MAINTENANCE OF BUILDINGS AND REPAIRS CLEANING OF MANHOLES SEPTIC TANKS FILTER BEDS ETC AT VISHWA VIHAR AND AKASH VIHAR UNDER GE AF MARATHAHALLI

Amount

Petty repairs to joinery works such as easing of doors, windows, kitchen cabinets , refixing builder hardware, wire gauge etc by providing glue nails and screws to the satisfaction of user and rectifying other misc minor carpentary works assigned by the Engneer In Charge.

Petty repairs to plumbing/internal water supply works such as repair to leaking bib taps, pillar taps, mixers, stop cocks by tightening and providing washer repair to float valves, low leveled cistern by mixture adjustments leaking water supply lines by tightening the GI fitting or refixing W/S or sanitary fixtures using thread/teflon taps and including small GI fittings such as GI elbow, socket, union etc as required at site to the satisfaction of user as assigned by the Engneer In Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises.

Taking down cement plaster any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Demolition of PCC of any description and in any position as in complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar , including all quions, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick Screed bed or bedding layer for laying floor finishes in cement mortar 1:6 complete

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick Screed bed or bedding layer for laying floor finishes in cement mortar 1:6 complete

S&F glazed ceramic coloured tiles 7mm thick 450 x 300mm size in verticle surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 complete.

S&F in repairs Vitreous China White Squatting Pan, ‘ORISSA’ Pattern of size 580x440 mm with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan and fixed-in-repairs, complete all as specified and as directed.

Supply and fix in repairs vitreous china wash down water closet pan (Pedestal pattern) white, fixed in repairs (excluding fixing bolts, flushing cistern and pipe) including taking down complete all as specified and directed..

Supply and fix plastic water closet seat cover any colour, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, fixing in repairs complete all as specified and directed.

S & F in repairs PVC valveless, syphonic action type flushing cistern 10 ltr capacity low level white with inlet ball valve float and handle including brackets and flush pipe of polyethylene of density of PVC 32 mm for low level cistern etc complete all as specified and directed.

S&F in repair wash hand basin of size 550 x 400 mm vitrous China white flat back including brackets, waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed.

S&F in repairs MS brackets 450mm long made with IAS 25x3mm suitable for wash hand basin complete all as specified and directed.

S&F PVC Connection 15mm size with PTMT Nuts of length 60cmmm and fixed-in-repairs, complete all as specified and as directed.

Supply and Fixing in repairs health faucets Chromium plated (hand shower) with 8mm dia 1.50m long flexible hose, wall hook fixed with brass screws and all accessories complete all as specified and directed.

S & F in repairs 15mm bore Pillar taps, cast copper heads, capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed..

S & F in repairs bip taps 15mm chromium plated cast copper alloy with crutch or butterfly handle, screw down for iron pipe or for brass ferrule all as specified and directed.

S & F in repairs bip taps long body 15mm chromium plated cast copper alloy with crutch or butterfly handle, screw down for iron pipe or for brass ferrule all as specified and directed.

S&F in repairs two in one Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed by Engineer-in-Charge

S & F in repairs stop valves 15mm , cast copper alloys, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or unions all as specified and directed.

S&F in repair 15mm bore PTMT Bib taps standard any colour screwed down for iron pipe and fixed minimum weight 90 gm complete all as specified and directed. Make: Prayag .

S&F in repair 20 mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210gms)complete all as specified and directed.Make: Prayag .

S&F in repair 25 mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210gms)complete all as specified and directed.Make: Prayag .

S&F in repairs , Brass chromium plated shower rose 125mm size complete all as specified and directed.

S&F in repair PTMT waste coupling of 32 mm dia (half or full thread) including taking down old coupling of any description complete all as specified and directed.

S&F in repairs 32 mm dia flexible waste pipe for wash basin and kitchen sink complete all as specified and directed.

M & L PVC floor trap with grating including jointing with solvent cement, 75 mm dia outlet complete all as specified and directed.

Taking up or down steel tubing and connections, 15mm bore complete all as specified and directed.

Taking up or down steel tubing and connections, 20mm bore complete all as specified and directed.

S & F 16 mm bore CPVC pipes SDR 11 & plain CPVC SDR11 fittings on walls and ceiling or laying in floors, with all fittings complete all as specified.

S & F 20 mm bore CPVC pipes SDR 11 & plain CPVC SDR11 fittings on walls and ceiling or laying in floors, with all fittings complete all as specified.

S&F in repair 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame)n. exc. 1.5 Sqm each all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications & drawings complete

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strips of 20mm width stuck inside with solven cement for styles and plain colour PVC sheets for top rain lock rail and bottom rail on either side and as gap insert for top rail and bottom rails, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet bedding and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete

S & F butt hinges 125mm size extruded aluminium alloy with galvanised mild steel hinge pin,anodised, all as specified and directed

S & F aluminium handles 150 mm size cast type anodised all as specified and directed

S & F Aluminium anodised bolts barrel tower bolts 200 mm long of extruded section all as specified and directed

S&F in repair 100 mm aluminium anodised barrel tower bolts, of extruded section all as specified and directed

S&F in repair 150 mm aluminium anodised barrel tower bolts, of extruded section all as specified and directed

S&F in repair 300mm aluminum anodised sliding door bolts, with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alluminium alloy complete all as specified and directed.

S&F in repair mild steel butt hinges of 75 mm size medium weight cold rolled by welding to existing frame complete all as specified and directed

S&F in repair mild steel butt hinges of 100 mm size medium weight cold rolled by welding to existing frame complete all as specified and directed

S&F in repair 100 mm size extruded aluminum alloy handles, fabricated type anodized complete all as specified and directed

S&F in repair 150 mm extruded aluminum alloy handles, fabricated type anodized complete all as specified and directed

S&F in repairs 100 mm long safety type aluminium anodised hasp and staple with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 20 mm dia D type chromium plated towel rail 600 mm long between flanges complete all as specified and directed.

S&F in repairs 20 mm dia anodised aluminium anodised powder coated tubular curtains rod including fixing brackets complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed.

S&F in repair mild steel helical door spring 300mm ordinary rat tail rod pattern springs including roller plate complete all as specified and directed.

Taking down rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends etc complete.

Supply and fix PVC (SWR) pipes single socketed 75 mm bore fixed in walls/Sunken floor.

Supply and fix PVC (SWR) bends 75 mm bore of any radius.

Supply and fix PVC (SWR) door Tee of size 75 mm.

Hacking out old broken glass ( any thickness, size, quality or description) from metal frame frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones including supply and fix 4mm thick sheet glass ordinary quality in square or n. exc 0.5 sqm each pane up to 4th floor complete all as specified and directed by Engr-in-charge.

Hacking out old broken glass ( any thickness, size, quality or description) from metal frame frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones including supply and fix 5 mm thick sheet glass ordinary quality in square or n. exc 0.5 sqm each pane above 4th floor complete all as specified and directed by Engr-in-charge.

Material and labour for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width 1:3:6, Type C-1 (20 mm graded crushed stone aggregate ) and setting in mortar cement mortar 1:6, complete.

Material and Labour for PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in coping, mud stops, benching, water tank platform etc.on roof, chajja weathering, slightly rounded or chamfered angles and throating etc. including necessary form work complete all as specified and as directed.

Material and Labour for PCC (1:2:4) type B-O using 12.5 mm graded crushed stone aggregate as in padding over roof for filling depression and making proper slope complete all as specified and as directed.

M & L for rendering 5mm thick cement plaster in cement mortar 1:3 on ceiling including finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 10 mm thick in patches in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and as directed.

Rendering 15mm thick in patches in cement mortar in 1:4 on fare face of brick work or concrete surfaces even and smooth without using extra cement & with using integral water proofing compound complete all as specified and as directed.

M&L for preparation of new surface/undecorated surfaces surface of ceiling and applying three coats of white washing complete all as specified and as directed.

M&L for preparation of new surface/undecorated surfaces of walls and applying two coats of Oil bound distemper over a coat of priming on plastered and other surfaces with alkali resistant priming paint complete all as specified and as directed.

M&L for preparation of new surface/undecorated surfaces of walls and applying two coats of Cement Base Paint of approved tint over a coat of priming on plastered and other surfaces with alkali resistant priming paint complete all as specified

S&F in repair galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm dia and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Removing demolished material exc 1.5 KM but n.exc 5 KM and depositing where directed at a level n.exc 1.50 M above the starting points all as specified.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes etc exc 250 liters and not exc 500 liters and writing date of cleaning with white paint on each tanks complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes etc exc 500 liters and not exc 1000 liters capacity tanks and writing date of cleaning with white paint on each tank complete all as specified and as directed.

S&F in repairs rotational moulded polythylene water storage tanks 500 ltrs capacity, ISI MARKED (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge

S&F in repairs rotational moulded polythylene water storage tanks 1000 ltrs capacity ISI MARKED (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge

S&F in repair round moulded PVC water tank lid for specially 500 Ltrs, 1000 Ltrs complete all as specified and directed.

Material and Labour for cleaning of sewer lines from Manhole to Manhole (including manholes enroute) of any depth and dia of pipe including testing sewer line by pouring water complete all as directed by Engr-in-Charge.

Cleaning of Manhole Upto 2m depth, any size and any depth including taking out sludge, sewer water, any other materials etc and disposal of the same outside MD land complete all as directed by Engr-in-Charge. Note:- Payment of blockage shall be paid again to the manhole if the blockage occurs after the interval of 1 month.

Cleaning of Manhole Exc 2m but not exc 4m depth, any size and any depth including taking out sludge, sewer water, any other materials etc and disposal of the same outside MD land complete all as directed by Engr-in-Charge. Note:- Payment of blockage shall be paid again to the manhole if the blockage occurs after the interval of 1 month.

Excavation in trenches for exposing the sewage line and breaking SGSW pipe horizontally on top to help cleaning the sewer line from Manhole to the location where the SGSW pipe is broken and covering the broken portion of SGSW pipe from the top and sealing the opening in CM (1:3) including returning filling and ramming in trenches with excavated earth and disposal off surplus earth to a distance not exceeding. 50 m complete all as directed by Engr-in-charge (irrespective of depth and type of soil).

Cleaning blockages from Nahani trap to Gully trap by Roding etc and cleaning the sludge from NT taking up and refixing the grating in CM (1:3) including testing by pouring the water until smooth flow, complete all as directed by Engineer-in-charge. Note:- Payment of blockage shall be paid again to the manhole if the blockage occurs after the interval of 15 Days.

Cleaning of blockages from Gully trap to 1st Manhole length of sewer line not exceed 5m by roding etc and cleaning all sludge from Gully trap to 1st Manhole including pouring water until the smooth flow and necessary earth work and disposed of sludge etc complete all as directed. Note:- Payment of blockage shall be paid again to the manhole if the blockage occurs after the interval of 15 Days complete all as specified and as directed.

Cleaning blockages from water closet including cleaning the soil pipe (for 1St and 6th floor) by removing the access door cover in the bend and refixing it after cleaning the pipe, pouring water until smooth flow including necessary earth work and making good damages if any to plinth protection Manhole etc., all as directed. Note:- Payment of blockage shall be paid again to the manhole if the blockage occurs after the interval of 15 Days.

Demolition of existing SWSG gully trap including PCC kerb etc and supply and fix SWG gully trap square mouthed 100mm size set in PCC (1:3:6) type C1 block measuring 450mm and 100mm thick bed concrete and jointing to drain pipe in cement mortar (1:1) including 100x150mm high PCC kerb in (1:2:4) type B1 with CI perforated grating 150x150mm bituminous coated including disposal of waste/sludge complete all as directed.

Demolition of PCC around floor trap and dismantling existing floor trap and cleaning the blockage of pipe from floor trap to gully trap and supply and fix PVC floor/Nahani trap in existing pipe and embedding in cement mortar (1:1) including lowering or raising with vertical piece with PVC pipe for jointing trap and fixing gratings at true level of floor complete all as directed.

Removing / Bailing out of sewage water from the septic tank of various capacities and disposal outside MD land including cutting and removing all vegetable growth plants etc in around septic tank and filter bed etc and removing debris outside MD land complete all as specified and as directed.

Removal of sludge/disposal/sediment from septic tank of various capacities and disposal the same outside MD land including cutting and removing all vegetable growth plants etc including uprooting of small plants around septic tanks and filter beds and etc and removing debris outside MD land complete all as specified and as directed.

Removal/taking out of sludge muck consisting of loose aggregate sediments mud etc from filter bed and refilling the same after cleaning/washing into the filter bed complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and n. exc. 1.50 mtr deep and getting out in hard/dense soil complete all as specified and as directed.

Excavation in trenches but exceeding 1.5m deep and not exceeding 3.00m deep getting out in hard/dense soil complete all as specified and as directed.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25cm thick each complete in hard/dense soil all as specified and as directed.

Removing excavated soil to a distance exceeding 50m and not exceeding 100m and depositing where directed at level not exceeding 1.50m above the starting point.

Demolition and breaking up drain pipe (salt glazed stone ware) set in Cement Mortar, 150mm bore and getting out from trenches complete all as specified and as directed.

Cutting into existing Main Hole for connecting new drains, making good to pipe and rendering, cutting out existing benching and forming branch channel (1/2 round or 3/4 section) in cement concrete PCC (1:2:4) type B1, smooth finished and reforming benching as required internal dia of pipe 150mm complete all as specified and directed.

Material and Labour for 150mm bore salt glazed stone ware drain pipes laid in trenches and jointed in cement mortar (1:1) and tested complete all as specified and directed

Material and Labour for PCC (1:3:6) type C-2 for bed to drain pipes 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested, complete all as directed.

Material and Labour for forming fair finish to channel in manholes using extra cement.

Material and Labour for rendering 15mm thick in CM 1:4 on brick or cement concrete surfaces & finished even and smooth without using extra cement.

Material and Labour for PCC (1:3:6) type C2 using 40mm graded stone aggregate in foundation.

Material and Labour for pre cast cover slab using PCC (1:2:4) type B1 and set in CM 1:6 with top surface finished even & fair complete all as specified.

Use and waste the form work to Formwork to sides of concrete foundation, footings, bases of columns, rafts & rafts beams, sides & soffits (if any) of foundation & plinth beams; & similar work; vertical or to batter fair finished surface.

Material and Labour for TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally or hoping for columns, hooking ends & binding with including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed.

Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

Sai Ram Builders

C R R CONSTRUCTIONS

yuvan constructions

M/S SIRI BUILDERS

docileworx

sri sai construction

M/s STAR ELECTRICALS