SPL REPAIR OF ROAD ENTRY GATE TO HQ UNDER GE NAMS

Material and labour for Repair to pot holes any depth, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc cutting around edges to at least 25 mm in depth making good the surface by applying a tack coat 5 kg/10 Sqm ,putting in premixed bituminous macadam well rammed and sealed with binder @ 9.8 kg / ten Sqm , blinded with 0.09 cum of stone chipping 6.3mm size and again well rammed to uniform surfaces , depth of pot hole not exceeding 30mm thick complete, all as specified as directed.

Material and labour for preparing black top surfaces by brushing with wire brushes for removing caked ,mud etc. sweeping with brooms and finally fanning the cleaned surfaces with air compressor to remove all loose dirt and applying evenly a priming tack coat with paving bitumen primer @ 5 kg/10 sqm using paving bitumen VG 10 and laying semi dense Asphaltic bituminous concrete ( SDAC ) 30mm consolidated thickness with 5.5% binder content VG 30 by weight of total mix with mechanical paver mixing in hot mix plant , rolled and consolidated to required camber and gradient with 8 to 10 tonne mechanical power roller complete, all as specified and directed. Note :- (a) Material for premixed carpet and sand seal coat shall be mixed in hot mixing plant duly approved by GE. ( b) Mix design of bituminous SDAC will be got done from approved lab. (c) The premix carpet shall be laid with mechanical paver.

Material and labour premixed bituminous, macadam laid/ rolled and compacted to required gradient and camber with using 20mm graded stone aggregate and paving bitumen @4% by the weight of total mix (consolidated thickness 75mm thick or less or as required) with 10 to 12 ton power roller complete, all as specified and directed.

Material and labour premixed bituminous, macadam laid/ rolled and compacted to required gradient and camber with using 20mm graded stone aggregate and paving bitumen @4% by the weight of total mix (consolidated more than thickness 75mm thick or as required) with 10 to 12 ton power roller complete, all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete, all as specified as directed.

Supply and fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints and necessary fittings laid in floors/wall or trenches complete, all as specified as directed.

Material and labour for stone kerb of machine pressed coloured precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate, block of finished at top bullnosed shape and finished surface even and smooth using coloured pigment and jointed in CM 1:6 struck finished complete, all as specified as directed.

Supply and fixing in repair Solar Cat eye / Stud of size 125mmX125mmX25mm (Shank 60mm) with aluminium alloy shell, high efficiency Mono - crystalline solar panel 2.40 V/0.30 Watt having one Ni-Mh are Ni-Cd rechargeable battery (1.2 V)/1600 MA), Six super bright LEDs with 10,000 to 18,000 mcd (Milli Candela) having flash rate 02 Hz and bearable weight 10 tons approx with view distance upto 1000 Mtrs of any colour i.e yellow, red, blue, green or white as required at site, working temp 10 degrees to 75 degrees C, working time 3 to 4 days after fully charged battery, charging time 5 to 6 hours from direct sun light, maintenance free unbreakable poly carbonate clear facing , automatically turns on at night and turns off at dawn including all fixing arrangement as per manufactures instructions complete, all as specified as directed. Make : DA 110(DHRUV) of DARK EYE or equivalent from list of makes.

Supply and fixing CAT'S EYE designed to provide enhanced, dependable road guidance to motorists in bad weather conditions, made out of strong ABS moulded body with polycarbonate /PMMA (Acrylic) micro prismatic reflectors ultrasonically welded on the moulded ABS body for maximum retro reflection in wet and dry conditions and to be fixed with Epoxy - Resin based adhesive or special Hot Melt Bitumen adhesive avoiding nails etc complete, all as specified as directed. Make :- 3Model No. DA972.0 or equivalent of Makes specified in list of Makes to be approved by GE.

Material and labour in repair for road delineator ABS round body, reflective reflectors (Amber/Red colour) and mounted on MS pipe 50mm dia duly powder coated overall length 850mm fitted with anti rust and theft steel net including welding of mild steel flat iron at bottom of delineator of size 25x5mm, 150mm long , necessary excavation and embedded in PCC block 1:2:4 type B1 of size 30x15x30cm complete, all as specified as directed. Make:- Dark Eye Model No DA-74 or equivalent of Makes specified in list of Makes