8124 PROVN OF TOILET FOR GENTS AND LADIES STAFF NEAR BLDG P8C PROVN OF 1 X TOILET AND BATHROOM AT SINGLE OFFICERS MESS PROVN OF COVERED SHED AT CENTRAL CADET MESS PROVN OF BARBED WIRE FENCING AT AFMC HOUSE AND PROVN OF 11 NOS SLIDING WINDOWS AT AFMC

Amount

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing rubbish off the premises complete all as directed.

Demolition of plain cement concrete of any description and in any positon not otherwise specifically provided and removing from site complete all as directed.

Demolition of Reinforced Concrete of any description and in any position not otherwise specifically provided for and removing from site complete all as directed.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars etc but excluding ashlars facings dressed stone work and precast PCC Block, complete including removing from site complete all as directe.

Taking down chowkats or frames of wooden / steel n.exc 1.5 sqm with shutters (without taking off shuttrs from the frames) & removing from site including making good to disturbed jambs complete all as directed.

All as per item No 5 here-in-before but exc 1.5Sqm and n exc 4.0 Sqm each.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and removing from site complete all as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to to a distance not exceeding 50 M and making good surface complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / disintegrated rock complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material exc 1.50 Km. & n exc 5 km & depositing out side of MOD Land complete all as specified and directed.

M & L broken stone or boulder hard core gauge, n exc 63mm deposited spread and leveled in layers n.exc 15cm thick watered and rolled/rammed to a true surfaces complete all as specified and directed.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for PCC in 1:4:8 type D2(using 40 mm graded stone aggregate) in foundation filling, mass concrete complete all as specified and directed.

All as per item No 16 here-in-before but (1:2:4) type B2.

M & L for damp proof course 40mm thk to horizontal or vertical surfaces in cement concrete 1:2:4 type B-0 with using WPC as per manufacturer’s instructions including necessary formwork complete all as specified and directed.

M & L RCC M-25 Design mix for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

All as per item No 19 here-in-before but for Columns, pillars, piers, posts and struts complete all as specified and directed.

All as per item No 19 here-in-before but for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

All as per item No 19 here-in-before but for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

All as per item No 19 here-in-before but for chajjas

Use and waste of formwork to sides of rough finished surface of concrete foundations, footings, bases of columns, plinth beams and similar work vertical or to batter complete all as specified and directed.

All as per item No 24 here-in-before but to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

All as per item No 24 here-in-before but to sides and soffits of roof beam, lintels etc. including supports,overhangs and also splays between floors and beams complete all as specified and directed.

All as per item No 24 here-in-before but to soffits of roof slab not exceeding 200mm thk . including supports,overhangs complete all as specified and directed.

All as per item No 24 here-in-before but to chajjas including edges complete.

All as per item No 24 here-in-above but to rough finished surface of concrete edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M & L for precast cement concrete block masonry exceeding 10cm in width witth solid blocks of PCC (1:5:8) gde D-5 built in CM 1:6 complete all as specified and directed.

M & L solid block masonry n. exc 10 cm width, using blocks of Grade D4(1:5:8) built in cement mortar 1:4 complete all as specified and directed.

M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M & L Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M & L for cutting out bricks, forming toothing for, and bonding new into old work built in CM 1:6 including value of new materials entering old walls and jointing and pointing complete all as specified and directed.

M & L 40 mm thick Flush shutters, solid core construction, with partical board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F in opening solid PVC door frame of size 50mm x47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with prelam sheet reinforced with MS square tube, complete all as specified and directed.

S & F factory made solid PVC moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face complete all as specified and directed.

S & F butt hinges 100mm size extruded aluminium alloy with galvanised mild steel hinge pin anodised, type B-21 complete all as specified and directed.

S & F aluminium anodised, barrel tower bolts 200 mm long of extruded section and fixed complete all as specified and directed.

S & F extruded aluminium alloy handles, 150 mm size, fabricated type, anodised complete all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M & L 125 mm x 60 mm with 1.2 mm thick (PBI sheet with PCC 1:3:6 filling in inner core of frame) Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M & L Steel work in tubular trusses, post, struts etc including special shaped washer complete using ERW or induction butt welded tubes conforming to I. S.1161-1998 grade St.-240 complete all as specified and directed.

M & L roof trusses (framed), trussed, purlins, rails, fastenings and heavy bracket framing including distance pieces, cleats etc grade (Fe-410-W E-250, quality B) complete all as specified and directed.

M & L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment , grade Fe-410 W E-250 quality B complete all as specified and directed.

M & L for framed work as in grill, gratings, guard bars framed work for misc works including welding etc and other simiar work conforming to Fe-290 gde E-165 complete all as specified and directed.

M & L posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F Wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) incl all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L mild steel bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) 0.9mm dia or securing with clips quality confirming to TMT bars.

All as per item no 49 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders.

S & F welded steel wire fabric fixed to wood or steel members n exc 4 kg per sqm complete all as specified and directed.

M & L Mild steel sheet 1 mm thk & 100 mm dia eaves gutters, galvanised class 3, half round with rounded edges complete all as specified and directed.

S & F Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of heavy duty galvanised mild steel wire, staples or staple pins etc as ditected ( Each line wire to be measured) etc complete all as specified and as directed.

S & F ventiltors/ louvers with partially guaged shutter using 5 mm thick x 10 cm wide frosted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed.

Glazing clips 19352

S & F three track sliding window with two or more shutter with 4 mm thick tinted glass , one shutter of stainless steel wire cloth 0.56 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle lock, rubber beading and glazing clips etc using following aluminium powder coated sections confroming to catalogue of 'JINDAL' or of equivalent make complete all as specified directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & Verrtical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & Bottom 20844 (f) Glazing Clip 19352

S & F aluminum powder coated partition Pattern approved by GE using Jindal or equivalent Sections DP/SP weight not less than 1.0 kg/RM with frosted glass 5 mm thick and 12 mm thick prelaminiated particle board (both side laminated) fixed with glazing clips,Jointing cleats.rubber gasket,nepprene packing, anodised aluminium snap beading screws complete all as specifed and directed.

M & L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L polycarbonate sheet 1.50 mm thick of any colour having Specific gravity not less than 1.2 kg per sqm for roof covering and ridge, fixed with self tapping screws or otherwise specified etc directed by engineer in charge.

M&L for 12 mm thick gypsum board for ceiling on and including aluminium powder coated grid work 60 cm x 60 cm with using 36.5 mm x 23.5 mm x1.5 mm thick main tee, 23.5 x 23.5 mm x 1.28 cross tee and 25 x 25x 1.5 mm angles fixed to perimeter of wall for false ceiling including necessary supporting hanger with 4.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling suspended @ 120 cm C/C both and applying two coats of washable distemper over a coat of primar complete all as specified and directed.

S & F aluminium (die cast) body Door closer hydraluically regulated designation no 2 universal type suitable for door shutter of 701 to 850 mm in width and weight between 36to 60 kg complete all as specified and directed.

M & L for PCC 1:4:8 type D2(using 40 mm graded stone aggregate) 75 mm thick as in sub-base conc. Surface complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection/ path etc finished even and smooth without using extra cement complete all as specified and directed.

M & L for non skid coloured ceramic tiles (of any colour) flooring 7 to 8 mm thick area of each tile exceeding 0.11 sqm and not exc 0.18 sqm with joint free tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick cement screed bed in CM 1:6 complete all as specified and directed.

M & L for 300 x 200 x 6 to 7mm / 450 x 300 x 6 to 7 mm thick, coloured glazed ceramic tiles as in skirting/dado laid and jointed in neat cement slurry and pointed in coloured cement to match complete over and including 10mm thick rendering in CM (1:3) and triangular filleting on top in cement mortar 1:4 complete all as specified and directed.

M & L for designed chequred coloured tiles (path tiles) 25cmx25cmx22mm thick laid over and including 20 mm thk screed bed in CM 1:6 set jointed in neat cement slurry and pointed in coloured cement matching to tiles all as specified and directed.

M & L for 10mm thick rendering in CM 1:6 on concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M & L for 5mm thick rendering in CM 1:3 on concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15mm thick in CM 1:4 on brick or concrete surfaces finished with sponge finish with using water proofing compound as per manufacturer's instruction complete all as specified and directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mi- tres and stopped ends, etc complete all as specified and directed.

M & L for broken glass coping on top of walls in CM 1:3 complete all as specified and directed.

Supply only integral water proofing compound

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer all as specified and directed.

Complete removal of existing treatment and M&L for applying 2mm thick wall care putty and applying two coats of oil bound distemper over one coat of primer on walls all as specified and directed.

M & L for preparation of newly plastered surface and appliying three coats of white washing on ceiling all as spd and directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over one coat of primer all as specified and directed.

M & L for preparation of old plastered surfaces of wall and applying one coat of cement base paint complete all as specified and directed.

M & L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as spd and directed

M & L for preparaion of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as spd and directed.

M & L for preparation of old steel surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M & L for preparation of new surface of steel of any description not otherwise described n exc 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M & L machine cut kota stone slab flooring 20to 25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick screed bed in CM (1:6) including rubbing and polishing complete all as specified and directed.

M & L granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing laid over and including 20mm screed bed in cement mortar (1:6) complete all as specifed and directed.

Rounding to edges of stone slabs one edge such as in steps or similar situation complete all as specified and directed.

S & F 75mm dia PVC floor Trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

S & F salt glazed stone ware gully traps square of size 150 x 150 mm including setting & jointing to drains with CM (1:1) complete all as specified and directed.

S & F 75mm dia cast iron soil , waste and vent pipe in any length with or without ears with cement joints laid in floors complete all as specified and directed.

S & F 15mm bore GI tubing "medium grade" galvanized with all fittings and fixed complete to walls and ceilinng or laid in floors etc complete all as specified and directed.

All as per item No 89 here-in-before but 20mm bore.

Cutting chases, pinning in making good to facings where required and pointing in CM 1:4 for concealed water tubing etc complete all as specified and directed.

S & F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to wallsv or laid in floor complete all as specified and directed.

All as per item No 92 here-in-before but but 75mm bore.

All as per item No 93 here-in-before but laid in trenches.

S & F PVC (SWR)110 mm bore bends any radius all as specified and directed.

All as per item No 95 here-in-before but 75mm bore.

S & F PVC (SWR) branch piece 110mm bore double (double Y) equal or unequal complete all as specified and directed.

S & F PVC (SWR) 110mm bore vent cowl all as specified and directed.

M & L for RCC pipes class NP-2 with socketed ends laid and jointed complete with rubber ring joints of 150 mm dia complete all as specified and directed.

M & L for cement concrete 1:4:8 type D2 in concrete bed to 150mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Cutting into existing manhole for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finish and reforming benching as required complete all as specified and directed.

M & L for PCC 1:2:4 type B-1, (using 20mm graded stone aggregate) as in benching in drains incl all moulds and forms all as specified and directed.

M & L for PCC 1: 2:4 type B0 as in copping including weathering, slightly rounded or chamfered angles and throatly all as specified and directed.

M & L for providing precast RCC (1:2:4) type B1 using 20 mm graded stone aggregate in Manholes covers set in CM 1:4 complete all as specified and directed.

S & F 32 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed.

S & F 1000 lit Rotational moulded polythylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position with 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plasitc ball complete all as specified in SSR Part-I.

All as per item No 106 here-in-before but 500 litre capacity tank.

S & F 20mm bore gun metal globe or gate valves with iron wheel head, screwed boh ends for iron pipe and fixed complete all as specified and directed.

S & F 150mm size square grating of PTMT (min weight 100gms) all as specified and directed.

S & F PVC connection 60 cm long ,15mm dia size with PTMT nuts all as specified and directed.

S & F cromium plated pegstay three in each set all as directed.

S & F pillar taps CP 15mm dia , cast copper alloy with capstan heads, screwed down high pressure with long screwed shanks and flynuts complete, screwed for iron pipe complete all as per cat No CON-021KN of make Jaquar or equivalent model from approved makes given in the make list.

S & F chromium plated two way bib cock with wall flange 15mm dia as per Cat No-29041 ‘Fusion (Quarter Turn)' of make Jaquar or equivalent model from the approved make given in the make list.

S & F 15 mm bore bib taps,fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15mm bore stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F 15mm dia angular stop cock with wall flange cast copper alloy chromium plated fancy type screwed down high pressure with crutch or buterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F CP towel rail 20mm dia and 600mm long including brackets complete all as per cat No CAN -111N of make Jaquar or equivalent model from approved make given in the make list.

S & F toilet paper holder, stainless steel, box type fix to wall withh cromium plated brass screws complete all as specified and directed.

S & F 125 mm dia swivel type brass chromium plated shower rose of approved quality complete all as specified and directed.

S & F for health faucet as per cat No ALD-573 of make Jaquar or equivalent model from approved make given in the make list.

S & F vitreous china squatting Pan " Orissa " pattern of size 580 mm X 440 mm white with integral foot rests ( excluding flushing cistern and flush pipe) including provn of cement concrete bedding & PVC (SWR) 'P' trap complete all as specified and directed.

S & F vitreous china wash down water closet pan, 'Pedestal' coloured , including fixing bolts etc including PVC seat cover white flat bottom with aluminium anodised hinging devices (excluding flushing cistern and flush pipe) complete all as specified and directed.

S & F vitreous china wash hand basin, white, overall size 550x 400mm flat back including fixing with fasteners/CI brackets, PVC waste pipe 32mm dia, CP brass waste coupling 32mm dia etc complete all as specified and directed.

S & F oval shaped coloured vitreous china WHB table top Colonia snow white, fancy type of overall size 595 x 380 mm, cat No 7751 of cera or of equivalent make specified here-in-after including 32 mm CP waste coupling, PVC waste pipe etc complete, including granite slab counter of black colour as approved and of size 1.20mtr x 0.60 mtr includingrounding edges etc complete cutting nitches rounding edges etc complete, horizontally supported by 01 No of 35 mm thick cuddappa stone slab one side mirror polished complete all as specified and directed.

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S & F chromium plated soap dish fixed to walls with chromium plated brass screws complete all as specified and directed.

S & F PVC Valve less syphonic action type flushing cistern 10 liters capacity, low level white ,with inlet ball valve float and handle including brackets & flush pipe of polyethylene of low or high density PVC 32 mm dia for low level cistern complete all as specified and directed.

S & F 600mm dia auto ventifresh air ventilator of stainless steel including 2mm thick transperent acrylic sheet fixing with 'L' or 'J' type hooks ,bitumen washers fixed in roof complete all as per manufacturer's instructions and as directed.

M & L for applying bitumin primer @ 0.30 ltr/Sqm conforming to IS 3384 use in waterproofing treatment and laying APP polymer membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyster non moven fabric (wt. not less than 150 gms/ sqm) laid on primer by force application complete all as specified & finish and sealing all the over laps of 75 mm in length side and 100 mm on the width side of membrane by torching the same all as per manufacturer's instruction including applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane complete all as specified and as directed.

Cutting existing steel tubing for alterations or additions of 20mm bore pipe complete all as directed.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated unsheathed 1100 Volts, ISI-694 marked drawn through duly concealed in wall /roof/ floor along with suitable fittings with MS sunken boxes of 1.6 mm thick, of suitable size including 3mm thick for laminated backelite sheet ISI marked for having switches sockets etc along with1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified forOne light/fan point controlled by one, one way switch. Note :- Rate for cutting chases in walls and making good as per the existing shall be included in the quoted rate and no extra cost shall be admissible for the same.

S & F for Switch piano, flush type single pole, one way 5 Amp all as specified.

S & F for ceiling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver. Make - Crompton model - Trans Air or equivalent model from the approved make given in the make list.

S & F for wall mounted LED tube light fitting 20 watts with output of 2000 lumens , box type (decorative) light fitting, 230 volts with extruded CRCA sheet coated heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 20 watts complete all as specified and as directed. Make :- Make HPL Cat part No HLPLEDT820(CW) 20W or equivalent model from the approved make given in the make list.

Supply and fix in replacement LED Tube light fittings wall mounted, 18 W LED 6500K with Opal white Poly Carbonate diffuser provided with high efficient integral constant current LED Driver 230 V etc. complete with mounting batten including all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size from ceiling rose to connector Conforming to Cat Part No. BLRB DB 118 & BLRB18 W CW LED of Make :- Bajaj or equivalent model from the apporved make given in the make list.

S & F bulkhead luminaries including LED bulb 10w Make Bajaj Cat part No 112334 BIBWP 10W LED or equivalent model from the approved make given in the make list.

S & F Distribution board sheet metal enclosure double door, factory made fixed flush with wall inside niches for mounting MCBs 240 Volts with bus bars with front openable cover Single pole and neutral 4 Way with 200 A busbar with IP 54 Proection complete all as specified and as directed.

S & F for MCB DB, SPN, sheet metal enclosure, 2 way complete all as specified and directed.

S & F for MCB double pole of rated capacity 32 amps, 240 volts breaking capacity 10 KA, C-curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA ,C- curve complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 2.5 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor drawn through and including non-metallic rigid 20 mm PVC rigid , ISI marked and its accessories duly PVC conduit in wall/ roof / floor including one run of single core 2.5 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor cable as earth continuity conductor along with the wiring and connected from DB to DB/ main board complete all as specified and as directed.

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to depth of not less than 1.5 m below ground level connected to and incl GI wire 4 mm dia and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover and MS angle iron frame, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete.

M & L for Reinforced concrete pipes class NP 2 with one collar per length of pipe of dia 100 mm 2 nos half round (for bottom and top ) and before laying excavated area shall be leveling all as specified and directed by Engr - in - Charge

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core.

M & L for machine cut cudappa stone slab 20-25mm thick over 15mm thick cement screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

All as per item No 133 here-in-before but drawn through PVC surface conduit.

L.T Associate

SUJATA CONSTRUCTION