Construction of Transit Accommodation/Labour Shed-cum-Night Shelters for construction workers in Tinsukia, Assam

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, lift upto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soil as directed, within a lead of 50m. 2.8.1- All kinds of soil.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc., complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(Zone III) : 4 graded stone aggregate 12.5mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Weather shade, Chajjas, corbels etc., including edges

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in allcolours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixedwith pigment of matching shadecomplete.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointedwith grey cement slurry, including rubbing and polishing completewith :Makrana white second quality.

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:3 (1 cement: 3 fine sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal wood

Block board construction flush door with teak wood ply on both faces 35 mm thick

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Chromium plated Brass handles 75mm with plate 125x32 mm

Brass cupboard lock 6 levers of approved quality, 75 mm size

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chamberedframe with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes,wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track four panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 4.00 sqm upto 8.00 sqm).

Zinc alloy (white powder coated) casement handle for uPVC window/door

Fixing standard steel glazed doors, windows and ventilators in walls, including fixing of float glass panes with glazing clips and special metalsash putty of approved make, or metal beading with screws, (only steel windows, glass panes cut to size and glazing clips or metal beading with screws, shall be supplied by department free of cost. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product - For horizontal surface one coat @1.10 kg per sqm.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Applying breathable, non-reactive, antifungal, and water repellant Silane/Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials & labours involved except scaffolding).

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms.

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

PVC slotted pipe 150 mm dia as per IS: 12818

PVC slotted pipe 200 mm dia as per IS: 12818

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 40 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 100 mm nominal dia Pipes

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore

Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40 gms.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

C.I. trap for standard urinal with vent arm with operating and other couplings in C.P. brass: 80 mm dia

Shower rose C.P. brass for 15 to 20 mm inlet 150 mm dia

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

Mild steel tubes hot finished seamless type

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

Coloured inter locking C.C. paver Block

Gravel 5 mm to 10 mm

PVC blind pipe 150 mm dia as per IS: 12818

C.I. 500 mm dia cover with frame (medium duty)

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed,within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure orextra earth to be paid for separately)

Providing and stacking of Fishtail palm of ht. 270-300 cm bottom girth 40- 50 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 60-90 cm, with 8-10 branches, and healthy foliage, bushy in big size HDPE bag as per direction of the officer-in-charge.

Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed (the cost of sludge, manure and the good earth shall be paid for separately).

Boring, providing and installation bored cast-in-situ reinforced cementconcrete piles of grade M-25 of specified diameter and length belowthe pile cap, to carry a safe working load not less than specified,excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). 450 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. Single pile upto 50 tonne Safe capacity. Initial test (Test Load 2.5 times the Safe capacity)

Routine test (Test Load 1.5 times the Safe capacity)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work. 50 mm nominal dia Pipes

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. Rocky strata including Boulders. 350 mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.Rocky strata including Boulders. 350 mm dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with ,outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.200 mm nominal size dia having minimum wall thickness 5.40 mm

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).200 mm dia

Supplying, installation, testing and commissioning of water lubricated Submersible Pump Set 3-Phase (for 3HP/ 5HP/ 7.5HP/10HP) / Single phase (for 1 HP / 2HP) pump with bronze impeller of suitable diameter all complete."&" The pump set should be coupled with wet type submersible electric motor drive of adequate power suitable for operation at 230V/ 415 V, 50 Hz input power including supply of steel cable rope,"&" G.I. column pipe, suction strainer, Sluice Valve, Non-Return valve, sockets, bends, elbows etc. & GI delivery piping above ground up to sluice valve above ground level, electrical cable of adequate cross section,"&" clips electrical switch gear (starter) etc., Electric Control Panel Board made of MS Sheet duly painted with Anti-corrosive paints complete fitted with all electrical accessories i.e. Off-On Switch, Voltmeter, Ameter, Indicator light etc.,"&" bright Annealed Electrolytic Bar Copper Conducted PVC insulated sheathed round flexible 3-core Cable of the Motor Manufactured conforming to IS:694/1990 all complete as specified and directed by the Department with One year warranty from the date"&" of commissioning and satisfactory testing against any manufacturing defect. [If any such defect is found during the year from the date of installation and satisfactory testing, supplier will have to rectify the defect at their cost and risk & if necessary replace the pump set.] Test Certificate of Pump, Motor, Starter, Panel Board, etc. from the manufacturer shall have to be submitted:Discharge of the pump MRecommended make:- Kirloskar/ Jyoti/ Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guar or equivalent" 3 phase 3 HP pump, head considering all losses(m): 55

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Plastering-: 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Single Cot (Bunker Bed). Overall size of the Cot – 2060L x 900D x 750mm H (Bed . height w/o mattress -400mm). The cot design is simple, modular & minimalist design, quick & easy to. assemble, weldless technology, stable & sturdy to take adequate weight.. Vertical Tubes are from Sq.40x1.2 thk tubes and horizontal beams are. Rectangular tubular profiles of 60x40 confirming to IS 4923:2017. All 04. vertical sections/legs are connected to to form the under-structure, confirming. to IS 4923:2017 grade.All legs & Beams are connected by press fitting the uniquely designed metal. formed hooks..Beam to beam are connected by cross beams of Sq.20mm ERW tube. confirming to IS 4923:2017, which supports the mattress platform. Mattress. platform is of 12mm thk plywood sheet. All metal parts comes with powder. coating finish 60-80 microns thk.. The legs are fitted with PPGF moulded leg bushes & levellers to adjust heights upto 20mm based on ground undulations.. Knock Down Construction . Note - Matress, pillows & Bedshhet Not Included . * Make: Featherlite

BED SIDE TABLE. SIZE: 450W X 450D X 510HT. 1 Drawer on Top + Open shelf below. Body - made up of 18MM Thk Prelaminated Particle Board with 2 MM PVC Edge banding . Drawer - With full panel drawer slides and Finger groove handle with cam Lock . Finish - As per Approved Shade . * Make: Featherlite

MATTRESS. Size: 1981mm x 915mm x 100mm thk. Slipwell, * Make: Featherlite

CANTEEN TABLE. Size: 1200W x 800D x 750HT. Table Top: HDHMR. Understructure: Wooden Legs. * Make: Featherlite

CANTEEN CHAIR. MODEL: TANG, * Make: Featherlite

CONFERENCE TABLE. Size : 4800W X 1200D X 750HT . Specifications:- Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges. of workstation surface shall be provided with machine pressed 2mm thick imported PVC . lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: 25 mm thick PLT gable end. Modesty Panel: 18 mm thick 450mm ht plt modesty panel. is considered which is machine pressed 2 mm thick imported PVC lipping glued with hot melt Eva glue free , from any VOC. Wire Management - 450mm Anodised flip up Made of Aluminium in anodised finish, which has soft closure and three way wire access & PVC cable tray. For entry of cables from the floor into the cable tray, vertical wire entry covers are provided for entry of power and data. * Make: Featherlite.

CONFERENCE MAIN CHAIR. MODEL: AMAZE MB BLACK ML ADJ ARMS. * Medium Mesh Back Chair , * Self Calibrating Multilock Mechanism. * Adjustable Lumbar Support, * Height Adjustable Arms, * Nylon Base, * Make: Featherlite

CONFERENCE BACK CHAIR. MODEL: CONTACT PROJECT VA FXD ARMS PC . * Contact Project . * Mesh Back . * Visitors chair . * Powdercoated Sledge Base . * Fixed Arms . *Make: Featherlite.

CABIN TABLE. Main Table : 1500W X 750D X 750 HT. Specifications:Table top : Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Understructure – Powder coated 50 x 50 perform legs and 40 x 20 cross beam. Modesty Panel: 18mm prelam Modesty. Wire Management: Raceway provided below table top for Power and Skirting Level for Data. 65mm dia grommet hole for wire access. *Make: Featherlite

CABIN STORAGE. Side Composite Storage : 900W X 450D X 750 HT. Table Top:18mm Thk pre laminated . particle board. Back:9mm Thk per laminated particle. board with 2mm PVC edge lipping. Shutters:18mm Thk PLB. Edge:All exposed area with 2mm thick . PVC edge lipping. Handle:Finger groove handle. Lock:Regular lock. *Make: Featherlite

STORAGE. Size : 900W X 450D X 2100HT . Table Top:18mm Thk pre laminated . particle board. Back:9mm Thk per laminated particle . board with 2mm PVC edge lipping.. Shutters:18mm Thk PLB. Edge:All exposed area with 2mm thick . PVC edge lipping.. Handle:Finger groove handle. Lock:Regular lock.*Make: Featherlite

WRITING DESK CHAIR. MODEL: RADDON WD. * Raddon Visitors chair. * Cushion Seat & Back . * With Arms . * Writing Desk.* Make: Featherlite

Supplying, carrying & installing Double Wooden Bed with Headboard (78''X72'')

Supplying, carrying & installing Double bed matress : Four Layers Foam Mattress of size 1981 mm x 1829 mm

Supplying, carrying & installing Almirah : Wooden Almirah / Wardrobe without Mirror with 3 Shelves

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automaticoperation and consisting of following, complete in allrespects, as required : (A) Horizontal type, multistage, centrifugal, split casingpump of cast iron body & bronze impeller with stainlesssteel shaft, mechanical seal conforming to IS 1520. (B) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operationon 415 volts, 3 phase 50 Hz, AC supply with IP 55protection for enclosure, horizontal foot mounted typewith Class-'F' insulation, conforming to IS-325. (C) M.S. fabricated Common base plate, coupling, couplingguard, foundation bolts etc. as required. (D) Suitable cement concrete foundation duly plasteredwith anti vibration pads. 1620 lpm at 56 m Head

Providing laying, testing & commissioning of 'C' classheavy duty MS Pipe conforming to IS 1239/3589 i/cfittings like elbows, tees, flanges, tapers, nuts bolts,gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports,anticorrosive treatment with coal tar/asphalt tape as perIS 10221, refilling the trench etc. of following sizes complete as required. 200 mm. dia (wall thickness = 6.3 mm)

Providing laying, testing & commissioning of 'C' classheavy duty MS Pipe conforming to IS 1239/3589 i/cfittings like elbows, tees, flanges, tapers, nuts bolts,gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports,anticorrosive treatment with coal tar/asphalt tape as perIS 10221, refilling the trench etc. of following sizes complete as required. 150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 40mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150mm

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying and fixing Single headed external yardhydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel,ISI marked, conforming to IS 5290 (type A) with blankGunmetal/Stainless Steel cap and chain as required. Single headed Stainless steel

Supplying, fixing, testing & commissioning of doubleflanged sluice valve of rating PN 1.6 with non risingspindle, bronze/gun metal seat, ISI marked completewith nuts, bolts, washers, gaskets and conforming to IS780 of following sizes as required : 100mm dia

Supplying, fixing, testing & commissioning of doubleflanged sluice valve of rating PN 1.6 with non risingspindle, bronze/gun metal seat, ISI marked completewith nuts, bolts, washers, gaskets and conforming to IS780 of following sizes as required : 150mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange& landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, 100mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, 150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipment on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Stainless Steel (Grade 304)

Supplying and fixing of fire brigade connection ofcast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. forsuitable dia MS pipe connection conforming to IS 904 as required. 4 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm diaquartzoid bulb type sprinklers of rating 68 degreecentigrade with required accessories : Pendant/ Upright sprinkler

Providing & fixing of pressure switch in M.S. pipe lineincluding connection etc. as required.

Supply, installation, testing and commissioning of fire hose box, suitable for accommodating 2 sets of 15m long 63mm dia, RRL hose pipe and one branch pipe. The hose box shall be double door, made out of CRCA sheet (not less than 2mm thick) with due process of anti rust treatment and powder coated with red enamel paint complete with locking arrangement

Providing, fixing, testing & commissioning ofinstallation control valve of cast iron body,brass/bronze working parts comprising of water motoralarm, bronze seat clapper, clapper arm andhydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete withdrain valve and bypass, test control box, ball valves,MS pipe of required size, flanges, orifice plate, gasketetc of following sizes as required 150mm dia

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.4 Zone

Supplying & laying of 2x1.5 sq mm fire alarm armoured cable, 600/1000V rated with annealed copper conductor ha XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supply, installation, testing and commissioning of CO₂ Fire Extinguisher, ISI marked, conforming to IS:15683.Capacity 4.5 Kg

Supply, installation, testing and commissioning of ABC type Fire Extinguisher, ISI marked, conforming to IS:15683.Capacity 5 Kg

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered). Depth exceeding 1.5 m but not exceeding 3 m

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Manhole Cover with Frame.

Ladder

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 2 + 4 way/6 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.). 8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100 amps

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying 1200 mm sweep ceiling fan Orient /Usha/Cromton/Bajaj make.

Supplying of 300 mm Heavy Duty Exhaust Fan ( 900 RPM) Orient make

Supplying,Installation, testing and commissioning of surface mounted LED batten (20W) fitting 1200mm length having Lumen efficacy ≥ 120lm/watt, System Lumen output ≥ 2000 lm, Metal housing , CRI ≥ 80, Power factor ≥ 0.9, THD ≤ 10% having suitable diffuser and CCT in between 4000K to 6500 K (i/c both Limits) complete with all accessories etc. directly on ceiling/wall including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. (Philips/ Bajaj/ WIPRO/ JAQUAR or equivalent make).

Supplying fitting & fixing of LED Bulb non-dimmable in the existing batten / angle holder as required and as directed by the department ( Syska or eqvt. make). LED SRL Bulb (Maxglow) B-22 Base (6500K) --15W

"Supplying with installation testing and commissioning of Hi -wall split (Cordless remote) air conditioner of the following capacity complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit as directed by the department. Approved make Carrier, Hitachi, Diakin, Mitshubishi. Warranty: Company will have to provide warranty on the entire product for twelve months from the date of commissioning. Additional warranty on Rotary & Scroll Compressor will be four and two years respectively. Service: Three free services will have to be provided by the company apart from the breakdown calls, if any. 5 star rating--2.0TR split, Carrier/Voltas or equivallant Make

Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. 5.0 KVA Automatic Input 90-280 V Out put 200-240 V, (Vee-Dee/Luminous or equivallant make)

Supplying with fitting and fixing of Single Phase Modular Motor Starter switch of the following specification complete including making necessary connection as specified and directed by the deptt. Overload Relay Range 16 - 25 Amps in 3 Module

Supplying including installation,testing and commissioning of Extra Refrigerant pipe for Split type Air Conditioner Machine as specified and directed by the department

Supplying, installation, testing and commissioning of the 63KVA 11/0.4KV aluminium wound out door type oil filled Level-2 Distribution Transformer complete including all accessories like Earthing terminal, Liftung Lugs, Drain Valve, Oil filling Hole with plug, Silicagel Breather, First filling of Oil as per IS355, Arcing Horn, Radiator, Air Release Plug, Conservator Tank etc along with cost of load security, Meter Security and making necessary arrangement of obtaining NOC for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date .

Supplying hot dip Galvanized Steel tubular pole manufacturing out from electrically welded in 3 (three section having a base plate including providing all required building materials as directed and specified by the deptt. (BANSAL/SRP / Valmont / PARUTHI ENGR make) 410 SP 66 Length of pole = 12.00 metre., Length of sections, Bottom = 5.80 M, Middle = 3.10 M, Top = 3.10 M, Out side dia. & Thickness Bottom = 219.10 x 5.60 mm, Middle =193.7 x 4.85 mm, Top =165.10 x 4.50 mm

Supplying and fixing of 11KV GOAB Switch 150Amp with all accessories complete as required and as directed by the department.

Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the department.

Supplying and fixing of 11 KV 5 KA Lighting arrestor (Poly) set complete as required and as directed by the department.

Supplying with fitting and fixing of galvanised channel of 100 mm x 50 mm x 6mm, 2200 mm long complete with clamps ,blots, nuts etc. as required and as directed by the department.

Supplying with fitting and fixing of Pole clamp of G.I. Flat (50x6)mm , as required and as directed by the department.

Supplying with fitting and fixing of G.I. LT Angle Crosarm( 40x40x6x500 ) mm , as required and as directed by the department.

Supplying with fitting and fixing of G.I. Angle (50x50x6)mm , as required and as directed by the department.

Supplying with fitting and fixing of G.I.Nuts & Bolts with washer , as required and as directed by the department.

Supplying with fitting and fixing of Microprocessor based with inbuilt earth fault protection module 4 pole MCCB 200A ICS= 100%, ICU 35KA(Minimum) , as required and as directed by the department.

Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. (RR Kabel/Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make or equivalent) . a) 3&1/2 x 50 Sq.mm. Tr.Panel to Vertical TPDB( Main Building)

Supplying with fitting and fixing of Aluminium Lugs 50 sq mm , as required and as directed by the department.

Supplying with fitting and fixing of C.I. Earth Pipe 1.8m Inner dia 100mm, outer dia 110mm with perforated holes of 15mm dia at 30 cm interval along length of the pipe

Supplying with fitting and fixing of 1.1 KV (LT) Grade Armoured 1CX95 sq mm Aluminium , as required and as directed by the department.

Supplying with fitting and fixing of Aluminium Lugs 95 sq mm , as required and as directed by the department.

Erection of steel tubular or rail pole strut in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling and secured with holding clamps, bolts, nuts, etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. Substation Earthing &Transformer Panel

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. Substation Earthing &Transformer Panel.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm). Transformer Neutral Earthing

APDCL Part. Supplying with fitting and fixing of LT Trivector energy meter with Metering Cabinet, as required and as directed by the department.

Construction of 11KV Over Head High Tention Line ( to be paid to APDCL as a Deposit works)

Load security to be paid to APDCL ( APDCL Norms)

Supplying fitting & fixing Single phase Submersible motor pump set suitable for 100 mm bore well and above 2 HP as directed & specified by the Department. (Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guard or equivallant make)

"Supplying fitting & fixing of Submersible motor pump set control panel as directed & specified by the Department. Type-FS 2HP DOL((Make- Havells,L&T,CRI or equivallant )

"Supplying fitting & fixing Three core cable with bare bounched copper conductor insulated & sheathed with pvc for Submersible pump motor as directed and specified by the department , Finolex/RRKabel/Havells or equivallant make. 3 core 6.00 sq mm

Supplying fitting & fixing of Wair Rope 10 mm size for keeping Submersible pump motor as directed and specified by the department.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

"Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f. mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) AMF Control Panel.5) Suitable batteries with lead.,6) First fill of lube oil.,7) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer.(Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Greaves, Leroy somer alternator). 58.5 KVA DG Set with AMF Panel

"Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20 protection) in powder painted sheet steel enclosure fitted on angle iron frame of the follwing capacity complete with making necessary connection as specified and directed by the deptt. (Standard/L&T/ Havells/ C&S/ HPL, make)

Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. (RR Kabel/Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make or equivalent) . a) 3&1/2 x 50 Sq.mm

Supplying with fitting and fixing of Aluminium Lugs 50 sq mm , as required and as directed by the department.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Construction of RCC Foundation for DG Set

Supply and Installation of 2 MP Fixed Dome Network Camera. Image Sensor:- 1/2.7" Progressive Scan CMOS, Max. Resolution:- 1920 × 1080 Min. Illumination:- Color: 0.005 Lux @ (F1.6, AGC ON), B/W: 0 Lux with IR (Make:- Hikvision)

Supply and Installation of 2 MP Fixed Bullet Network Camera. Image Sensor:- 1/2.7" Progressive Scan CMOS, Max. Resolution:- 1920 × 1080, Min. Illumination:- Color: 0.005 Lux @ (F1.6, AGC ON), B/W: 0 Lux with IR (Make:- Hikvision)

Supply and Installation of 32-ch 1U K Series AcuSense 4K NVR. H.265+/H.265/H.264+/H.264 video formats, Up to 2-ch@12 MP or 3- ch@8 MP or 6-ch@4 MP or 12-ch@1080p decoding capacity, Up to 256 Mbps incoming bandwidth (Make:- Hikvision)

Supply and Installation of 4TB Surveillance Grade Hard Drive for Storage (Make:- Seagate/ Toshiba/ WD)

Supply and Installation of 8 Port PoE Switch. (Make:- D-Link/ Digisol/ Netgear)

Supply and Installation of of 32” Full HD Display Monitor, BacklightDLED Backlight, Pixel Pitch:- 0.49(H)mm * 0.49(V) mm, Max Resolution:- 1920 * 1080 @60Hz, Brightness:- 360 cd/m²(typ.), Contrast:- 1200:1(typ.), Response Time:- 8ms (Make:- Hikvision)

Supply and Laying of Cat6 UTP Cables including RJ45 Connectors (Make:- D-Link/ Molex/ Netgear)

Supply and Laying of 1.5 Sqmm 3 Core Electric Wire (Make:- Finolex/ Havells/ KEI/ Polycab)

Supply of 9U Wall Mounted Equipment Rack (Make:- Valrack/ D-Link/ Netrack)

Supply and Installation of 4X4 PVC Box for Camera

Supply and Installation of 25MM PVC Pipe along with accessories (Make:- AKG/ Berlia/ Pearl Plast)

Supply and Installation of 2KVA Offline UPS with External Batteries and Bettery Rack (Make:- Microtek/ Numeric/ Delta)

Supply, Installation, Testing and Commissioning of 5,000 lumens XGA laserlight source projector. Display system: 3 LCD system, Size of effectivedisplay area:- 0.63”(16.0 mm) x 3 BrightEra LCD Panel, Aspect ratio: 4:3,Number of pixels:- 2,359,296 (1024 x 768 x 3) pixels, Throw ratio:- 1.41:1to 2.27:1, Contrast ratio (full white / full black):- ∞ :１,(Make:- Sony/ Christie/ Barco)

Supply, Installation, Testing and Commissioning of Projector Ceiling Mount Kit (Make:- Liberty/ Milan/ Suvira)

Supply, Installation, Testing and Commissioning of 8 Feet X 6 Feet Motorized Projection Screen (Make:- Liberty/ Milan/ Suvira)

Supply, Installation, Testing and Commissioning of POPUP BOX; Easy Access To Connectors Durable Pnematic Movementand Mechanical Latching Mechanism One Female 15pin HD Connector And 3.5mm Mini Stereo Audio Jack, Two CAT RJ45 network/data/phone Connectors, Two Unswitched AC Outputs, One HDMI (Make:- Magnum/ Extron/ Kramer)

Supplying installation, testing, programming and commissioning of 4x2 4K 18Gbps HDMI Matrix with Scaler and Audio De-Embedding. 4x2 HDMI Presentation Switcher with 4 HDMI inputs to 2 HDMI matrix outputs. HDMI 2.0b for resolutions up to UltraHD / 4K 60Hz (4:4:4) incl. HDR10. 4K to 1080p downscaling. HDCP 2.2 compliant. Smart EDID management ARC functions on second HDMI output, analog and digital audio de-embedding. Control via web-GUI, RS232 and IR, EDID management.Make:Purelink / Atlona / Extron / Lightware (Make:- Purelink/ Extron/ Aten)

Supplying installation, testing, programming and commissioning of Video equipment HDMI HDBaseT-Lite Extender (4K@40m)(HDBaseT Class B): Video: Max. Data Rate 10.2Gbps (3.4Gbps per lane) 10.2Gbps (3.4Gbps per lane), Max. Pixel Clock 340 MHz 340 MHz, Compliance HDMI (3D, Deep Color, 4K) HDCP Compatible, HDMI (3D, Deep Color, 4K) Max. Resolutions / Distance Up to 4K@35m (Cat 5e/6) / 40m (Cat 6a/ATEN 2L-2910 Cat6); 1080p@60m (Cat 5e/6) / 70m (Cat 6a/ATEN 2L-2910 Cat6) 4K supported: 4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0); 4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4) (Make:- Kramer/ Extron/ Aten)

Supply and Installation of High Resolution HDMI to HDMI Cable 1M (Make:- Kramer/ Belden/ Aten)

Supply and Installation of High Resolution HDMI to HDMI Cable 15M (Make:- Kramer/ Belden/ Aten)

Supplying installation, testing, programming and commissioning of Audio equipment ON TABLE BOUNDARY MICROPHONE for any conferencing system: Frequency response 40 Hz – 20 kHz, Nominal impedance 200 Ω, Sensitivity 10 mV/Pa. Frequency Response :- 40 Hz - 20 kHz, Max. sound pressure level:- 140 dB, Sensitivity :- 10 mV/Pa, Dynamic range :- 111 dB (A). (Make:- Sennheiser/ Shure/ Beyerdynamic)

Supply, Installation, Testing and Commissioning of Small Format DSP core with 8 user-configured card slots, Lua scripting engine, optional softwarelicensed HearClear AEC. (Make:- Xilica/ Biamp/ Q-Sys)

Supply, Installation, Testing and Commissioning of Analog Input Card having 2 Mic/ Line Inputs. (Make:- Xilica/ Biamp/ Q-Sys)

Supply, Installation, Testing and Commissioning of Analog Output Card having 2 Mic/ Line Outputs. (Make:- Xilica/ Biamp/ Q-Sys)

Supply, Installation, Testing and Commissioning of Wireless Handheld Microphone (Make:- Audio Technica/ Sennheiser/ Shure)

Supply, Installation, Testing and Commissioning of of 25 Watts 8" Full-ange Loudspeaker System; 50Hz - 16Khz; 90° Conical Nominal Dispersion; 8 Ohms Nominal Impedance And 6W,3W,1.5W @ 100V/ 70V (Make:- JBL/ Tannoy/ Funktion One)

Supply, Installation, Testing and Commissioning of 4 Channel Power Amplifier for above speakers . (Make:- Behringer/ Crown/ Powersoft)

Supply and Laying of 2 Core 1.5 Sqmm Speaker Cables (Make:- Polycab/ Finolex/ KEI)

Supply and Laying of Audio Signal/ Microphone Cables (Make:- Gotham/ Belden/ Klotz)

Supply and Installation of Audio Connectors and Accessories (Make:- Gotham/ Amphenol/ Neutrik)

Supply and Laying of 25MM PVC Conduits (Make:- AKG/ Berlia)

Supply and Laying of Cat 6 UTP Cable

Supply and Installation of 17U Floor Mounted Equipment Rack (Make:- Nettrack/ Valrack/ LinkEu)

Supply and Installation of USB Extension Cable 10M (Make:- Peoplelink/ Belden)

Supply, Installation, Testing and Commissioning of Video Conference Camera :Video System : 1080P, 720P, 540P, 480P, 360P, 240P etc. Sensor : 1/2.7'', CMOS, Effective Pixel: 2.07M Scanning Mode : Progressive Lens : f4.7mm ~ 46.3mm, F1.8 ~ F2.8 Optical Zoom : 10X Digital Zoom : 16x Minimal Illumination : 0.5 Lux @ (F1.8, AGC ON) Shutter : 1/30s ~ 1/10000s. Quad Microphone • 4 mic array, 4 meters radius intelligent pickup, up to 85dB speaker volume• Intelligent noise reduction, echo cancellation, AEC, full- duplex voice communication• Support USB/Bluetooth • LINE IN/OUT interface, connect to the conference terminal • Supports one extension unit • Come with Three-party call function • Built-in rechargeable battery (Make: PeopleLink)

ON GRID SOLAR POWER GENERATING PLANT. INCLUDING ALL ITEMS