CERTAIN SPECIAL REPAIR LBW AND MINOR WORKS IN THE AOR OF AGE BR I EM I AND EM II UNDER GE C KIRKEE

Amount

Surface excavation in soft/loose soil n.exc 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep and getting out complete all as specified and as directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m depth for foundation in hard rock and getting out complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth ; for foundation or for shafts, wells, cesspits, manholes, pierholes, etc n.exc 10 sqm on plan and n exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm thick in soil complete all as directed.

Removing excavated surplus soil not exc 50 m and depositing where directed at level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling as mass concrete complete all as specified and as directed.

M&L for providing RCC nominal mix type-A (1:1.5:3) (using 20mm graded stone aggregates) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for providing RCC nominal mix type A (1:1.5:3) (using 20mm graded stone aggregates) in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M & L for RCC nominal mix type-A (1:1.5:3) (using 20mm graded stone aggregates) as in Beams, cantilevers, bressumers, lintel bands, lintels over 1.5m span, etc complete all as specificed and as directed.

M&L for providing RCC nominal mix type-A (1:1.5:3) (using 20mm graded stone aggregates) in slabs supported on walls, floor slabs, roof slabs, and the like complete all as specified and as directed.

M&L for providing RCC nominal mix type-A (1:1.5:3) (using 20mm graded stone aggregates) in Chajjas complete all as specified and as directed.

M&L TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L TMT Mild steel bars 5mm dia and over upto and including 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders complete all as specified and as directed.

M&L Form work to sides of concrete foundations, footings bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation plinth beam and similar work vertical or bottom rough finished surfaces of concrete in flat and curved surfaces complete all as specificed and as directed.

M&L Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) with rough finished flat concrete surfaces complete all as specified.

M&L Form work to sides and soffits of floor or roof beams, beams haunching, girders, bressumers, lintels, cantilevers shelves including supports overhangs etc, also splays between floors and beams etc flat rough finished surface complete all as specificed and as directed.

M&L Form work to sides of pillars, posts, struts, piers, columns rough finished surfaces square, rectangular or polygonal complete all as specificed and as directed.

M & L for Hard core of gauge n.exc 63mm broken stone or boulders deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to true surface complete all as specified and as directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded granite stone aggregate) in sub base complete all as specificed and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 m clear span, cills, steps seismic and other similar bands plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height copings, kneelers, apex stones, bed plates, kerbs, water troughs, benching and the like including weathering, slightly rounded or chamfered angles and throating, complete all as directed.

M&L for precast cement concrete block masonry of grade C-5 having density not less than 1800 kg/cum and 28 days average minimum compressive strngth of block should be 5 N/sqmm as in walling set in cement mortar 1:6 complete all as specified and as directed.

M&L for precast cement concrete block masonry 10cm thick of grade C-5 (with plain or interlocking joints as directed) having density not less than 1800 kg/cum and 28 days average minimum compressive strngth of block should be 5 N/sqmm as in walling set in cement mortar 1:4 complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finishing top surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick/block/ masonry work or concrete surfaces in CM 1:4 (external) with or without using WPC and finishing top surfaces even and smooth without using extra cement complete all as specified and as directed.(WPC shall be measured and paid seperately)

M&L for 5mm thick rendering on concrete surfaces of ceiling in CM (1:3) and rendering is to be finished even and smooth without using extra cement complete all as specificed and as directed.

M&L 75mm thick Plain Cement concrete (1:3:6) Type C-2 (using 40mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement complete all as as specified and as directed by Engr-in-Charge.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in base course complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface 450 X 350 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10 mm thick cement plaster (1:4) as backing coat complete all as specificed and as directed.

M&L for sand/stone dust filling under floor or in foundation or for cushioning of UG cable/ at cable trenches including watering and consolidation complete all as specificed and as directed.

M&L for providing 60 mm thick machine pressed precast concrete interlocking paver blocks of any shape and size conforming to IS-15658-2006, with grey cement and pigment, rubber moulded tiles M-35 Grade, as in floors, paving, path etc. complete laid over sand cushioning complete all as specified and as directed.

S & F Factory made internal PVC door frame of size 50x47mm single revated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed by Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100 mm butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F 150mm size Extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

S&F aluminium anodised barrel tower bolt 150mm long of extruded section with steel screws complete all as specified and as directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete half fixed glazed and half top hung glazed complete all as specified and as directed (Glass shall be measured and paid separately).

S&F sheet glass 3 mm thick ordianary quality and galzing with oil putty in square n.exc 0.5 Sqm in each pane complete all as specified and as direcetd at site.

M & L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M & L preparation of newly plastered surface of wall and applying two coat of cement base paint (white or tinted) over a coat of alkali resistant primer complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of newly plastered surfaces complete all as specificed and as directed.

S&F Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests(excluding flushing cistern and flush pipe) including necessary lime concrete, connection to trap and to flushing pipe, antisyphonage pipe complete all as specified and as directed.

S&F wash down water closet (pedestal pattern) complete (including fixing of seat cover) pedestal pan and trap including connection to drain (or outgoing pipe ) and flushing pipe, antisyphonage pipe etc complete all as specificed and as directed.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc complete all as specified and as directed.

S&F wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and as directed.

S&F Vitreous china (White) urinal half stall type (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and as directed.(Make : Parryware/cera/Hindware)

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S & F stop cock (concealed) cast copper alloy, chromium plated fancy type screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions or brass ferrule with long shunk and cup 15mm bore complete all as specified and as directed.

S&F bib taps, cast copper alloy, chromium plated, fancy type screwed for 15mm bore of iron pipe or for brass ferrule complete all as specified and as directed.

S & F stop valves cast copper alloy, screwed down, high pressure with butterfly handle, screwed both ends for iron pipe or for unions 20mm bore complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F 500 litres capacity rotational moulded, polythene water storage tanks triple layered (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) triple layered hoisted and fixed in position complete all as specified and as directed.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe. (Minimum weight 15mm-142gms/ 20 mm - 210 gms . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed.

S & F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) complete all as specified and as directed.

S&F PVC (SWR) pipes, single socketed, 110mm bore in any length with rubber ring joints, fixed to walls etc complete all as specified and directed

S&F PVC (SWR) pipes, 75 mm bore, single socketed, in any length with rubber ring joints, fixed to walls etc complete all as specified and directed.

S&F PVC (SWR) junction single (Single 'T') equal or unequal, 100mm bore/dia with access door complete all as specified and as directed.

S&F PVC (SWR) bends of any radius 110 mm bore/dia duck's foot or heel rest complete all as specified and as directed.

S&F PVC (SWR) bends of any radius 75 mm bore/dia duck's foot or heel rest complete all as specified and as directed.

S&F PVC (SWR) reducers 75 mm bore/dia complete all as specified and as directed.

S&F 110 mm dia of outlet PVC (SWR) 'P' trap, jointing with solvent cement complete all as specificed and as directed.

S&F 75mm bore/dia PVC vent cowl all as specified and directed.

S&F 100mm bore/dia PVC vent cowl all as specified and directed.

S & F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm bore etc complete all as specified and directed.

S&F 75 mm dia of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specificed and as directed.

M&L brick work with fly ash old size bricks straight or curved on plan exc 6 m mean radius in CM 1:6 complete all as specified and as directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Supply only approved liquid integral waterproofing compound @ 0.20 lit per 50 kg of cement complete all as specified and as directed.

M & L TMT mild steel bars 6 to 8mm dia, cut to length, bent to shape required inluding cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L Precast RCC slab 1:2:4, type B1(using 20mm graded stone aggregates) as in cover slab (for manholes), landings, chajjas,water troughs,hangers, shelves and similar articles with plain faces set in CM 1:6 complete all as specified and directed.

M&L for providing plain cement concrete 1:4:8 type D-2 (Using 40 mm graded stone aggregates) as in concrete bed to drain pipes for 150 mm bore dia including packing under haunching against the side of pipe after laid and tested etc. complete all as specified and as directed.

M&L for Reinforced cement concrete pipes,150 mm bore of pipes Class NP-2, laid and jointed with collars complete all as specified and as directed.

S & F of conventional type, on site LLDPE septic tank designed to carry sewage and sullage water, including excavation in any type of soil/rock, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 20 users all as specified and directed.(Make :- Approved make of E-in-C)

M&L for Soakage wells of size 1.2M diaX 3.0 M effective depth excavation, in any type of soil/rock PCC in foundation, walls of honey combed Brick masonry with top ring of RCC including intercepting chamber and screen chamber made of Brick masonary in cement mortar, RCC cover slab / SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size all as speified and as shown in drawing No.CEPZ/2019/TD/03 Sheet 1/1 and 1/2 dated 30 Apr 2019 and as directed by Engr-in charge.

Supply fixing and laying in trenches galvanised steel water tubing 20 mm bore, medium grade with and including all medium grade fittings complete all as specified.

Supply fixing and laying in trenches galvanised steel water tubing 15 mm bore, medium grade with and including all medium grade fittings complete all as specified.

S&F gun metal gate valve with iron wheel head, screwed both ends for iron pipes 20 mm bore complete all as specified and directed.

S&F gun metal gate valve with iron wheel head, screwed both ends for iron pipes 25 mm bore complete all as specified and directed.

M&L for cutting and welding of existing CI/GI pipe in trenches for fixing/inserting of valve, bends , double socket, Tee pieces, single branch, Y junction etc, of any size of pipe complete by using nesessary cutting material such as gas cutter etc. all as directed by Engineer-in-Charge.

Cutting existing for GI steel tubing 25 to 32mm for alterations or additions from overhead tank on roof for new connection as per the site condition complete all as directed by Engineer-in-Charge.

M&L Cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed.

M&L Forming 12 mm thick expansion joint with pre-formed filler and top 30 mm primed and sealed with sealing compound Grade ‘A’ all as specified for thickness of concrete slab 150mm complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A' complete all as specified and directed.

M&L Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified and directed.

Excavating in post holes (or similar holes) in hard dense soil each n exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

M&L plain cement concrete 1:2:4, type B-2 (using 40mm graded stone aggregates) as in foundations, filling and mass concrete etc. complete all as specified and as directed.

M&L Rolled mild steel in roof truss (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, rectangular section conforming to Fe 410 -W(Gde-E- 250) quality-A, complete all as specified and as directed.

M&L Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 410 -W(Gde-E- 250) quality-A complete all as specified and as directed.

S&F pre painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F mild steel screw bolts machine made with hexagoanl or square heads at one end and screwed the other on screwed both ends each screwed to be fitted with washers and one hexagonal or square nut length of bolt exc 5cm but n exc 10cm long and dia of the neck 5 to 10 mm dia complete all as specified.

M&L for preparing new Steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying evenly two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for Reinforced cement concrete pipes,150 mm bore of pipes Class NP-2, laid and jointed with collars including demolition and breaking up drain pipes (SGSW/AC/RCC) including haunching and benching set in cement mortar complete all as specified and as directed.

M&L for Reinforced cement concrete pipes, 200 mm bore of pipes Class NP-2, laid and jointed with collars including demolition and breaking up drain pipes (SGSW/AC/RCC) including haunching and benching set in cement mortar complete all as specified and as directed.

M&L for Reinforced cement concrete pipes, 300 mm bore of pipes Class NP-2, laid and jointed with collars including demolition and breaking up drain pipes (SGSW/AC/RCC) including haunching and benching set in cement mortar complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 using 40 mm graded coarse aggregate in bed to drain pipes of 150 mm bore including forming cradles complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 using 40 mm graded coarse aggregate in bed to drain pipes of 200 mm bore including forming cradles complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 using 40 mm graded coarse aggregate in bed to drain pipes of 300 mm bore including forming cradles complete all as specified and as directed.

Cleaning of existing septic tank of 100 to 200 users capacity by using Mechanical Pumping Machine to removing water, sludge, stones, solid particles etc complete from the septic tank at any location and at distance from road and removing the same from the campus and buried complete all as specified and as directed as below: (i) The sludge/burried soil etc taken out shall be stacked alongwith the septic tank, sump well etc. After 48 hours of the sludge taken out, measurement shall be taken as of the solid contents for the purpose of payment. The tenderer are advised to keep this aspect in mind while quotating the rates. After taking the measurements, the solid contents shall be disposed off outside the Md land/area. (ii) Necessary precautions as well as safety measures shall be taken by the contractor without any extra cost, for working in the foul conditions. (iii) The contractor shall be entirely responsible for the lapse, mishappening to any of the manpower deployed and/or to other equipment/machinary/material at the site of work during the execution. (iv) For cleaning the sewere line/manholes also refer relevant clauses of particular specifications here-in-after.

Demolition of reinforced cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

S&F PVC (SWR) pipes, single socketed, 110mm bore in any length with rubber ring joints, laid in trenches or floors etc including taking down existing unserviceable SWR pipes and fittings complete all as specified and directed

S&F PVC (SWR) pipes, single socketed, 75mm bore in any length with rubber ring joints, laid in trenches or floors etc including taking down existing unserviceable SWR pipes and fittings complete all as specified and directed

S&F PVC (SWR) junction single (Single 'T') equal or unequal, 100mm bore/dia complete all as specified and as directed.

S&F PVC (SWR) junction single (Single 'T') equal or unequal, 75mm bore/dia complete all as specified and as directed.

Excavation over areas, n exc 1.5 m deep and getting out in soft/disintegerated rock complete all as specified and as directed.

M&L plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregates) as in foundations,filling and mass concrete etc.complete all as specified & directed.

S&F aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc and making good the jambs and painting with paint should match with the existing suface complete all as specified and as directed.

M&L point wiring with 1.5 Sqmm size PVC insulated unsheathed 1100 volt grade single core stranded FRLSH (multithreaded) copper conductor cable drawn into and including PVC casing caping of suitable size with all fitting and accessories with sunk type pressed steel terminal/PVC surface type boxes of 1.6 mm with 3 mm thick laminated sheet top cover concealed/surface in walls complete for Provn of switches/socket/fan regulators including one continuous run of PVC insulated (green colour) 1.5 sqmm multi stranded FRLSH copper conductor cable as earth wire and connected to common earth dolly for the following :- One light/fan point controlled by one, one way 5 Amps switch.

All as per item No.119 One five pin 5 Amp socket outlet, on same bord with other switches.

All as per item No.119 five pin 5 Amp socket outlet on independent bord.

All as per item No 119 above but with 2.5 sqmm size PVC insulated and unsheathed 1100 volt grade multistranded FRLSH copper conductor cable for 5 pin socket outlet 15 amp on independent board.

S&F 5 Amp switch flush, piano type single pole one way 5 Amp 230 volts AC circuit complete all as specified and as directed.

S&F socket outlet, five pin, 5 Amp, flush type multipurpose, 230 volts AC circuit complete all as specified and as directed.

S&F socket outlet, five pin, 6 Amp, flush type, 230 volts AC circuit complete all as specified and as directed.

S&F 15 Amp switch flush, piano type single pole one way 230 volts AC circuit complete all as specified and as directed.

Supply and fix socket outlet flush type 2 in 1, combination outlet comprising of 3 pin 5/15 amp 230 volts AC circuit complete all as specified and as directed.

S&F ceiling rose PVC/ polycoarbonate, isolated body, three terminal complete all as specified and as directed.

S&F LED Light fitting 20 watt, 220 V, AC decorative box type with driver ,holder including LED Tube Light connecting with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F LED lamp 7 watt, CDL, E-27 230v PF-0.95(min).

S&F LED tube light fitting, 20 watt, CDL, 230 Volts, 4 feet long, Trim linea complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable incl LED lamp and mounting casing box 2 nos+E12 any type all as specified and directed. Make- crompton Cat Part No LCTLN-20-CDL or equivalent from list of approved make circulated by Engineer-in-Chief.

S&F LED tube light fitting, 2'long, 10 watt,CDL 230 Volts, Trim linea complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm two core copper flexible conductor cable with mounting casing box 2 nos+E12 any type all as specified and directed. Make-Make- crompton Cat Part No LCTLN-10-CDL or equivalent from list of approved make circulated by Engineer-in-Chief.

S&F LED building security light 15 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20/25mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener all as specified and directed. Make-shakti, Cat Part No SZPSLMM015 or equivalent from approved list of make circulated By E-in-C.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers all as specified and directed.

S&F MCB distribution board 08 way SPN 240 volts factory fabricated complete alongwith busbar, neutral link and Earth bar, without MCBs all as directed by Engineer-in-Charge.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN 6 to 32 Amp in the MCB DB complete with connection testing and commissioning.Make : Legrand cat part No. 4086-9 to 4086-17 or equivalent from list of approved make circulated by Engineer-in-Chief.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

S&F Sheet metal Enclosure SPN 4 way (MCB DB) IP 43 Double door, 240 Volts AC. Make: Legrand cat part No.5076 11 or equivalent from list of approved make circulated by Engineer-in-Chief.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP 6 to 32 Amp in the MCB DB complete with connection testing and commissioning.Make : Schneider cat part No. A9N1P06C to A9N1P32C or equivalent from list of approved make circulated by Engineer-in-Chief.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings.

Supplying and laying un-reinforced precast concrete cable cover, class HVP, Class LV, Type I, flat, size 250mm x 150mm x 40mm all as directed by Engineer-in-Charge.

M&L for surface submain wiring with two sinle core PVC insulated and unsheathed 1100 volt grade multistranded FRLSH copper conductor cable of size 4 sqmm in PVC casing caping of suitable size with all fittings and accessories alongwith one single core green colour 1100 volt grade multistranded FRLSH copper conductor cable of size 4 sqmm as earth lead and connected to earth dolly.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium solid conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sqmm, 2 core nominal cross section in service connections all as directed by Engineer-in-Charge.

Supply, laying in trenches and testing of UG cable 16sqmm 04 core XLPE insulated screened,PVC bedded galvanised steel strip or wire, armoured heavy duty electric power cable with stranded aluminium conductor 1100 volts complete all as directed and specified.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as directed by Engineer-in-Charge.

M&L for brick protection with old size sub-class bricks ‘B’ Designation 75 for UG cable.

Supply, laying through GI pipe in trenches or fixed to pole/wall or fixed to LT panel board, and testing of UG cable, PVC insulated, screened, PVC bedded galvanised steel strip or wire, armoured, electric power cable (heavy duty) with stranded aluminium conductor, 1100 volts grade of size 10 sqmm 2 core with required alumonium cable lugs, heat shrink joints, colour code heat shrink sleevs at both cable ends complete all as specified and directed.(Note: (i) Heat shrink joint 2 core/ 4 core will be measured and paid under appropriate item of this BOQ.(ii) GI tubing required new will be measured and paid seperatly under respective item of this BOQ. (iii) Heat shrink sleev of 25mm long on HS joint for colour indication will deemed to be included in the quoted rate.(iv) additional aluminium cable lugs require for jointing cable termination will deemed to be included in the quoted rate and no extra measuerment/payment will be made.

M&L Steel tubular swaged poles type 410 SP-31 (9.00 metres long) complete with cast iron base plate, finial taper plug, bolts, nuts & screws conforming to IS : 2713 and made out of structural tube conforming to IS : 1161 and painted internally with a coat of bituminous paint and externaly two coats of aluminium paint over a one coat of red oxide primer as specified.

S&F LED Flood light fitting of 120 watt with LED driver complete with bracket made of 25/32 mm GI pipe light grade, clamps, nuts, bolts and washers.(Make: Bajaj prod code 169983 or equivalent make from approved list of make.)

S&F LED security light fitting of 60 watt with LED driver complete with bracket made of 25/32 mm GI pipe light grade, clamps, nuts, bolts and washers.(Make: Havels cat part No. ENDURAPEARLPLUSSL60WLED or equivalent make from approved list of make.)

S&F pole mounted box of size 10"x8"x4" with hinged door with and including following: (a) Din rail for mounting DP MCB - 01 No. (b) Connector box suitable for 3 phase 4 wire min 16 Sqmm cable - 01 No.

M&L PVC insulated flexible cable 3 core 2.5 Sqmm drawn in PVC conduit 20mm dia clamped on pole with necessary clamps etc.

M&L Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3.00 meter long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300mm dia and 6.00 meter deep using suitable mechanical drilling rig (for drilling near the specified location), connected with galvanised steel earthing lead of 25x4mm all as shown in plate No.02, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2 with pit cover 400x400x80mm with 8mm dia MS handle, funnel, wiremesh, 32mm dia light grade GI tubing for protection of GI strip 25x4mm, charcoal and salt in alternate 150mm thick layer around GI earth pipe, including necessary returning filling in and removal all as specified or indicated in SSR Pt I, including testing to achieve earth resistant value as per IS specification on completion.

M & L GI tubing 40 mm dia light grade galvanized with all fittings and fixed to wall/pole or under road crossing with necessary clamps, nuts, bolts and washers for cable protection complete all as specified and directed.

M & L GI tubing 25 mm dia medium grade galvanized with all fittings and laying in trenches complete all as specified and directed.

M&L Cutting to the existing Road/hard standing upto 300mm deep and 200mm wide for crossing GI water pipe line and make good by filling mass concrete PCC 1:4:8 as per existing pattern complete all as directed by Engineer -in-charge.(Note: Mass concrete PCC 1:4:8 shall be measured and paid in seperate item of this BOQ)

Suppy install test and commissioning outdoor type LT panel(CPRI approved) confirming to relavent IS factory fabricated made out of 3 mm thick out door type CRCA sheet duly powder coated & suitable size to accomodate all accessories / fittings with suitable size of copper power wire and angle iron frame with following accessories comparmentlize in construction to accomodate incoming /outgoing Cables and connecting copper wire including foundation for fixing angle iron frame for panel. comprising of the following :-(a) MCCB 100 Amps, 4 pole -01 Nos (b) TPN MCB 63 Amp-02 Nos (c) SPN MCB 40 Amps - 02 Nos (d) Indication lamp RYB -01 set. (e)Ammeter & Voltmeter each one (f) Aluminium bus bar (g) one digital timer (g) one power contactor MNX 40 A 240 Volt all as specified and directed.Note- Panel shall be CPRI type tested and to be fabricated in ISO certified panel manufacturing factory-Panel Make-Success Engineers, Bhosari

Supply, Install, Testing and Commissioning of 'Solar Hot Water System' (Flat Plate Collector) based on indirect transfer of heat of capacity 200 litre per day including all fittings by means gas welding or brazing leak proof fully insulated with glass wool with supporting structure duly painted complete with hot water storage tank made from stainless steel sheet, brass socket and nipple fully insulated with glass wool with cold and hot water tubing, gun metal valves, coil type stainless steel heat exchanger with necessary wiring fixed on PCC platform all as specified and as directed. Make: SINTEX/BHEL/TATA/BP SOLAR INDIA LTD.NOTE: (i) The system will be provided 4 Sqmm copper conductor, PVC insulated multistranded, unsheathed FRLS cable drawn in ISI marked 25mm dia medium grade PVC conduit, concealed in wall surface/roof slab/ ceiling (4x1) with electric backup 3KW for 200 litre capacity solar water heating system. (ii) The hot water tube shall be 20mm KITEC(PEX-AL-PEX) and its cost upto 5.00 RM shall be deemed to be included in rate quoted against item descriped above. (iii) Thickness of stainless steel sheet of storage tank should be 20 gauge. (iv) The cost of medium grade 20mm water tubing with all fittings for filling water tank shall be deemed to be included in quoted unit rate against item descriped above. length beyond 5m shall be measured and paid seperately.

AJINKYA VIKRAM GAIKWAD

Vastushilpa Contrustion

A K ENTERPRISES