REPAIR/MAINT OF DG SETS, SIGN BOARD, STP AND CONNECTED ITEMS UNDER AGE E/M OF GE SATWARI

Amount

Material and labour for Routine servicing of DG Set capacity upto 30 KVA Make: Kirloskar/ Cimmins including drain out the unsv engine oil and taking out the fuel filter, oil filter, air filter from the engine as directed by Engr-in-charge Note :- Engine oil, Diesel filter, oil filter with Gaskit , coolent will be measured and paid separtely.

Ditto all as per Srl item No 1 here in before but of Cap 40 KVA DG Set

Ditto all as per Srl item No 1 here in before but of Cap 63 KVA DG Set

Ditto all as per Srl item No 1 here in before but of Cap 100 KVA DG Set

Ditto all as per Srl item No 1 here in before but of Cap 125 KVA DG Set

S & F in replacement of following spare part as per existing make / model of DG Set :-

Fuel filter of cap up to 40 KVA

Fuel filter of Cap 63 to 100 KVA

Fuel filter of Cap 125 KVA

Air filter of cap up to 40 KVA

Air filter of Cap 63 to 100 KVA

Air filter of Cap 125 KVA

Oil filter of cap up to 40 KVA

Oil filter of Cap 63 to 100 KVA

Oil filter of Cap 125 KVA

S&F refilling in replacement of engine oil grade 20W-40 of DG Set as directed by Engr-in-charge. Make Castrol/ Kirlosker/HP

Disconnecting the electrical connection for taking out unserviceable / BER equipment like DG set,Servo Voltage stablizer, LT panel Chloronation Plant etc, shifted from installation to MES store yard as directed by Engr-in Charge. The cost of transportation is deemed to be included in the quoted rate.

Supply & refilling coolant concentrate with high boiling point and low freezing point easy miscibility with water upto the required level complete. Make: Castrol/HP

Taking out the FIP from the Engine & sent to workshop for overhauling & calibration of FIP 40/63 KVA DG Set, 4 cylinder Make-Kirloskar / cummins with replacement of worn out part i.e plunger, delinking valve, copper washers, O rings which ever requried of site, .after overhauling & calibration of FIP. (a) FIP return back to site for refixing the original position testing & commisioning complete (b) Taking out the injector from the Engine and send to workshop for overhauling & calibration.calibration of the injector including replacement of the Nozzle -04 Nos. After calibration, injector send to the site for refixing the original position (c) Repair the baby pump including replacement of washers.as directed by Engr-in-Charge

Ditto all as per Srl item No 19 here in before but of size 100/125 KVA

M&L for dismantling, opening and cleaning of complete radiator assembly of following DG Sets, checking of water leakage, including upper and bottom tank cleaning of slots including welding/brazing where required and making 100% leak proof and washing with chemically anti corrosion /water solution by using jet pumping set and as well as cleaning manually by using steel wire brushes and removing all rust ,silt /corrosive material and making good smooth functioning and upper & bottom tank gasket set, all rusted nut, bolt, washer, radiator caps etc complete all as specified and directed by Engineer-in-Charge.

(a) Upto 63 KVA DG Set

(b) 100 to200 KVA DG Set

M&L for replacement of complete radiator assembly as per existing make along with gasket nut bolts washer of cap 125 DG Set as directed by Engr-in-charge.

M & L for dismantling the defective charging Alternator of 12 Volt DC, cleaning with cleaning agent, over hauling, and replacement of worn out parts i.e bearing of any description,field coil, which ever requried for functioning of alternator.

(a) Upto 63 KVA DG Set

(b) 100 to 125 KVA DG Set

M&L for disconnecting and dismantling the UNSV 12 Volt self starter assembly by removing the all bolts and nuts and disconnecting from DG sets, opening of self starter,overhauling of self starter, replacement of worn out bearing, bushes, field coil etc reconnecting testing and commissioning complete all as specified and directed by Engr-in-Charge.

(a) Upto 63 KVA DG Set

(b) 100 to 125 KVA DG Set

M & L for replacement of UNSV batteries of 180 AH, 12 volts Make: EXIDE POWER / Amron / AMCO

M & L for replacement of UNSV batteries of 150 AH, 12 volts Make: EXIDE POWER / Amron / AMCO

M & L for replacement of UNSV batteries of 90 AH, 12 volts Make: EXIDE POWER / Amron / AMCO

M & L for replacement of UNSV batteries of 60 AH, 12 volts Make: EXIDE POWER / Amron / AMCO

Supply and fix in replacement of Automatic voltage regulator unit with voltage regulation (+/-)0.5% and voltage setting (+/-) 2% up to 63 KVA complete as directed by Engr-in Charge . Make: Kirloskar/Cumins/Greaves

Ditto all as per Srl item No 35 here in before but of Cap 100 to 125 KVA DG Set

Supply and replacement of battery lead heavy duty of copper conductor standard red for (+ive) terminal and black for (-ive) terminal with battery terminal of one end and battery lugs at other end complete .

Supply & replacement of battery terminal clamps made up of brass heavy duty with nuts and bolts complete

S & F in replacement of battery charger having electronic Circuit consisting of tridodes, rectifiers, capacitors, resistances etc suitable to be mounted on control panel to charge the battery of the DG Set at all times whenever there is electric supply either on mains or DG Set complete all as specified.

Supply and fixing in replacement of fuel pipe as per existing make and size including fixing arrangements all as directed by Engr-in-charge.

Supply and fixing in replacement of radiator fan belt as per existing make and size as directed by Engr-in-charge.

Supply, fixing in replacement of monitoring panel for generator set up to 63 KVA comprising of following :- (a) Microprocessor based genset controller (Power Command) for metering, monitoring, governing. (b) Engine protection for low lub oil pressure, high coolant temperature (alarm & shutdown) (c) Alternator protection parameters like under voltage, over current, under frequency, over (d) Relay driven for remote annunciations (e) Cyclic cranking (f) Auto/manual start/stop (g) Alternator trim adjustment from the front key pad (h) Operates within a temperature range 0-60 degrees and humidity upto 95% (i) Remote monitoring capability through separate interface modules (j) Genset metering parameters like lube oil pressure, coolant temperature, engine speed (RPM), run hours, DC voltage, intake manifold temperature, 3 phase volts and 3 phase amperes, frequency, KW, KVA power factor etc for following capacity DG Set. Make :- Kirloskar/ Cummins

Ditto all as per Srl item No 42 here in before but of size 100/125 KVA

M & L for Top head overhalling along with replacement of oil seal, O Ring, Head gasket, head valve , sleave of cap upto 63 KVA DG Set as directed by Engr-in-charge

Ditto all as per Srl item No 44 here in before but of size 100 to 125 KVA

M & L for taking out alternater 415 V form DG set removing the burnt winding wire from stator field coil , cleaning the slots for rewinding, and rewinding the same with super enamelled copper winding wire superior quality as per exisitng gauge and size, varnishing, drying, and assembling & refixing the same all as specified and directed by Engr-in-charge of Cap upto 63 KVA

Description all as per srl item No 46 here in before but of size 100 to 125 KVA

M & L for taking out alternater 415 V form DG set removing the burnt winding wire from rotor, cleaning the slots for rewinding, and rewinding the same with super enamelled copper winding wire superior quality as per exisitng gauge and size, varnishing, drying, replacement of bearings and assembling & refixing the same all as specified and directed by Engr-in-charge of Cap upto 63 KVA

All as per srl item No 48 here in before but of size 100 to 125 KVA

Supply and fixing in replacement analog type Voltmeter Square as per existing make and size, complete all as specified and as directed.

Supply and fixing in replacement pressure gauage of 0-100 mnwp, complete all as specified and as directed.

Supply and fixing in replacement analog type Ampere meter as per existing make and size , complete all as specified and as directed.

Supply and fixing in replacement Hrs run meter as per existing make and size , complete all as specified and as directed.

Supply and Fixing in replacement of Printed Circuit Board Card of battery charging unit in any Cap of DG AMF panel board.or as directed by Engr-in-charge

Supply and Fixing in replacement of solenoid switch of any Cap of DG set or as directed by Engr-in-charge

Supply & fixing in replacement of onload change over switch 415V AC, 4 pole front openable type in sheet steel enclosure including fixing arrangements in existing panel/on wall, including provision of thimble, nut bolts etc of 200 Amp as directed by Engr-in-Charge

Supply & fixing in replacement of outdoor type LED Glow sign sticker board of size 3x4 ft in day night version of bright green colour with operating software and also with USB Cable slot for input data programing working temperature range -25 digree to 85 digree, protection class IP 56 along with inclauser of sheet metal board of size 22 gauge for holding of LED Glow sign board for fixing on wall including nut bolts and all fixing arrangement with electrical connections complete as directed by Engr-in-Charge

Supply and fixing in replacement of 3 Pole Contactor MNX 70. Make L&T/Seimens/Schneider

Supply and fixing in replacement of 3 Pole Contactor MNX 110. Make L&T/Seimens/Schneider

Supply and fixing in replacement of unsv MCCB 630 Amp 4 pole 36 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost.

Supply and fixing in replacement of unsv MCCB 400 Amp 4 pole 36 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost. Makes: Legrand(DPX^3) Cat No.422007 or equivalent make in list of makes.

Supply and fixing in replacement of unsv MCCB 4 pole 320 Amp, 36 KA and thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost. Make: LEGRAND Model No DPX>3 Cat Part No 422006 or equivalent make in list of makes.

Supply and fixing in replacement of unsv MCCB 250 Amp 4 pole 36 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost. Makes: Legrand(DPX^3) Cat No.420249 or equivalent make in list of makes.

Supply and fixing in replacement of unsv MCCB 200 Amp 4 pole 36 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost. Makes: Legrand(DPX^3) Cat No.420248 or equivalent make in list of makes.

Supply and fixing in replacement of unsv MCCB 160 Amp 4 pole 36 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost. Makes: Legrand(DPX^3) Cat No.420097 or equivalent make in list of makes.

Supply and fixing in replacement of unsv MCCB 125 Amp 4 pole 16 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost. Makes: Legrand(DPX^3) Cat No.420016 or equivalent make in list of makes

Supply and fixing in replacement of unsv MCCB 100 Amp 4 pole 16 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Outgoing and incoming spreaders should be provided for connecting cable without any extra cost. Makes: Legrand(DPX^3) Cat No.420015 or equivalent make in list of makes.

M&L For Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground to a depth not less than 3 mtr below normal ground level with top edge of earth plate at a depth not less than 2.25 mtr below ground level, earth plate surrounded by 15 cm thick packed layer of charcoal, magnicium sulphate, common salt and connected with in and including GI strip of size 32x6mm by means of stainless steel bolts, nuts, check nuts and washers connected to test point 40mm bore of GI pipe (light grade) from earth plate up to testing point for protection of GI strip and 20 mm bore GI pipe (medium grade) with wire mesh and funnel for watering including necessary excavation and earth work, (in any type of soil) PCC chamber (1:3:6) type C-2 with RCC cover with suitable size of handle made out of 8mm dia MS bars and angle iron 40 x 40x 3mm frame for cover complete all as shown in electrical plate No 3 of MES schedule Part I of SSR Part-I 2009 complete all as specified. RCC cover shall be painted with red paint over a primer coat and the rate include in the unit rate of item Note : If black soil required in earthing for proper resistivity , the same shall be provided by the contractor without any extra cost on this account

M&L For Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground to a depth not less than 3 mtr below normal ground level with top edge of earth plate at a depth not less than 2.25 mtr below ground level, earth plate surrounded by 15 cm thick packed layer of charcoal, magnicium sulphate, common salt and connected with in and including GI strip of size 25 x4 mm by means of stainless steel bolts, nuts, check nuts and washers connected to test point 40mm bore of GI pipe (light grade) from earth plate up to testing point for protection of GI strip and 20 mm bore GI pipe (medium grade) with wire mesh and funnel for watering including necessary excavation and earth work, (in any type of soil) PCC chamber (1:3:6) type C-2 with RCC cover with suitable size of handle made out of 8mm dia MS bars and angle iron 40 x 40x 3mm frame for cover complete all as shown in electrical plate No 3 of MES schedule Part I of SSR Part-I 2009 complete all as specified. RCC cover shall be painted with red paint over a primer coat and the rate include in the unit rate of item Note : If black soil required in earthing for proper resistivity , the same shall be provided by the contractor without any extra cost on this account

M& L bore Earthing in any type of soil hard dence /shoft disintegrated rock not less than 250 mm dia 16 feet deep filled and black soil up to 7 feet from bottom complete with galvanized steel pipe 40 mm bore medium grade 3 mtr length tapers at bottom and provide 12 mm holes at 75 mm centre to centre up to 205 mtr of lrngth from bottom burried directly in ground filled with 45 cm alternative layer of charcoal magnisium sulphate and salt up to ground level connected with earthing strip 32x6 above ground level by means od ss bolts nuts washers including brazing upto equipments in including GI steip drawn into GI pipe 40 mm dia light grade upto required lenth as protection pipe top edge of earth electrode to be plugged with GI plug complete as directed by Engr-in-Charge Note : If black soil required in earthing for proper resistivity , the same shall be provided by the contractor without any extra cost on this account

Disconnecting & Taking out clorine gas cylender 100 kg from the pump house / MES Store yard and fwd to Authorized workshop /dealer for removing all chlorine gas safely , the empty gas cylineder shall be deposited by the contractor in mes store yard as directed by Engr-in Charge NoteThe cost of transportation is deemed to be included in the quoted rate.

Cleaning of civil unit (Receiving chamber, screen channel, MBBR unit, Tube settle unit, chlorine contact tank and sludge drying bed) of the plant as directed by Engr-in Charge

M & L for replacement of tube settler media from tube settler tank of plant. PVC COOL tubes CD-TS120 (Loose leaves) surface Area: 11m2/m3 at 60 deg angle inclination, vertical ht 750mm

M & Filling of PVC bio pac floating media of MBBR unit of the plant as directed by Engr-in Charge

Supply and installation in replacement of fine bubble EPDM diffuser Dia 90mmx1000mm diffuser with 1 inch air inlet connection and SS 304 nipple EPDM membranes duly clamp. Type of diffuser : Tubular, Non-clog, Non-buoyant MOC of membrane : EPDM/PTFE layered EPDM MOC of diffuser internal : PP Silt size : Less than 1mm Area of influence zone : 2.5 Sqm Optimum through put - 10 cum/hr maximum allowable pressure - 0.7 kg/cm2. Make : SCOGEN

Taking out unserviceable butterfly valve and supply and fixing new butterfly valve (As per existing type) of cast iron both ends for flange fitting of size 200 mm dia complete

Ditto all as per Srl item No 79 here in before but size of 150 mm bore

Ditto all as per Srl item No 79 here in before but size of 100 mm bore

Ditto all as per Srl item No 79 here in before but size of 80 mm bore

Ditto all as per Srl item No 79 here in before but size of 50 mm bore

Cutting of wild grass ,bushes ,unwanted vegetation trees upto 30cm grith including roots from inside/surrounding of installations including cutting of bushes along barbed/cattle fencing of the installation comlete all as specified and directed by Engr-in-charge.

Replacement of automatic star delta starter three phase of size 40 HP as directed by Engr-in-charge

Ditto all as per Srl item No 85 here in before but size of 25 HP

Supply and fixing in replacement PVC insulated and PVC sheathed flat submersible cable 16 sqmm 3 core with stranded copper conductor 1100 volts grade suitable for submersible motors and pumps and making electric connections all as specified and directed. Make : Polycab / Finolex / Havells

M&L for taking out old unsv MS Pipe of size 200 mm and replacement the same on appropriate size complete with nut bolt flanged, packing material and testing all as specified and directed by Engr-in-charge.

Ditto all as per Srl item No 88 here in before but size of 150 mm bore

Ditto all as per Srl item No 88 here in before but size of 100 mm bore

Material and labour for run lead joint including all jointing material such as lead, spun yarn etc for 100 mm bore cast iron spigot & socketed pipe & fittings. (Exc earth work will be measured & paid for separetely.

Description all as per item No 91 here in before but for 150mm bore cast iron spigot & socketed pipe & fittings.

Description all as per Srl item No 91 here in before but for 200 mm bore pipe.

M&L for taking out 30 HP non clog submersible pumpset from sewage sump, disconnecting pipes, pump and transporting to workshop for reapir, cutting of burnt winding/cleaning of stator for rewinding with super enameled PVC copper wire of existing size,prviding with insulating materials, flame proof/water proof laminated insulated strips,cotton tape, varnishing complete and shifting back to site and lowering & assembling in the existing position, connecting and testing all as specified and directed by Engr-in-charge.

Description all as per srl item no 96 here in before but of size 7.5 HP to 15 HP

M & L for Replacement the defactive part of submersible pump sets are as under:-

(a) Thrust bearing of non clog submersible motor7.5 HP to 15 HP

(b) Gun metal bushes for non clog submersible motor 7.5 HP to 15 HP

(c) Impellers for non clog submersible pump 7.5 HP to 15 HP

(d) Bowl bush for non clog submersible pump 7.5 HP to 15 HP

(e) Neck ring for non clog submersible pump 7.5 HP to 15 HP

M&L for dismantling and de-coupling 20HP air blower pump from the electric motor and re-assembling the pump on existing foundation complete with motor after repair/overhaulding with following and testing complete all as specified and directed.The cost of transportation to and fro workshop is deemed to be included in the quoted rate. a) Adjustment of safety valve. b) Replacement of spring assy c) Re-metaling/turning of pump shaft. d) Replacement of oil ENKLO 320, oil seal, bearing, filter. e) Replacement of belts & pressure gauge.

M& L in replacement of single plase preventor 440 volt complete as directed by Engr-in-charge

Material and labour for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate for supporting of CI/GI pipes, header etc all as specified and directed.

Material and labour in replacement of Cast iron fitting for CI spigot socketed/ flanged pipe bend (any type radius and angle) tapers any type (straight, bends increasing, decreasing or double socket etc) tee pieces, single branch 'Y' junction double branch cross (all socket or socket spigot or flanged) collars, cap and plugs upto 200 mm bore connection pieces one end flanged and other socket or spigot and bell mouth piece one end flanged and other end tapering as bell mouth complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of pipe line ,connection etc and getting out all in hard and dense soil.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point.

M& L in replacement of contactor 3 pole with coil voltage 220 volt type MNX 50 Rating complete as directed by Engr-in-charge

Supply and fixing in replacement of MCCB 200 amps cap 4P 415 volt breaking cap 35 KA with adjustable thermal and adjustable magnetic settings Make Havells / L&T / C&S

Supply and fixing in replacement of MCCB 100 amps cap 4P 415 volt breaking cap 16 KA with adjustable thermal and adjustable magnetic settings Make Havells / L&T / C&S

Supply and fixing in replacement of MCCB 63 amps cap 4P 415 volt breaking cap 16 KA with adjustable thermal and adjustable magnetic settings Make Havells / L&T / C&S

Supply and fixng in replacement Cast iron Non return valve (NRV) 150 mm bore complete conforming to IS 1969 double flanged and drilled including bolts, nuts, washers, gasket etc complete and dismantling of old one complete all as specified and directed. Make : Kirlosker/VENUS/ SANT

Description all as per Srl item No 113 here in before but 100mm bore pipe

Supply and fixing in replacement cast iron body sluice valve heavy duty class PN 1.6 flanged ends any pattern with cast iron wheel & mild steel spindle ISI marked confirming to IS-14846 of 2000 for 150 mm bore pipe with jointing material ,flanged joint,rubber gasket 6mm thick, nuts & bolts, washer complete all as specified and directed. Make:- Kirlosker/VENUS/ SANT

Description all as per Srl item No 115 here in before but 100mm bore pipe

Carry out water (Raw and treated ) from all STP plant and testing for bacterial, chemical and biological analysis of sewage water treated water from Govt approved lab for following parameters and submission of test reports all as directed: - (a) PH (b) Chemical Oxygen demand/COD (c) Biological Oxygen Demant/BOD (d) Total Suspended solids (e) Oil and Grease (f) TKN (g) Total Coliform (h) Organism MPN (k) Dissolved Oxygen Note: Water testing shall be carried out twice in peroid of contract all as directed and empty collection bottle will be provided by the contractor.

Taking out sludge from underground main sewage/drainage receiving sump (10 metre diameter and 6 metre deep) and removing it to a distance not less than 150 metre incluidng scrapping off the walls and cleaning by applying bleaching powder @ 1Kg per sqm complete all as directed.

Description all as per srl item No 118 here-in-before but size (8 metre diameter 6 metre deep).

Description all as per srl item No 118 here-in-before but size (12 metre diameter 6 metre deep).

Description all as per srl item No 118 here-in-before but open type and size (12 metre diameter 6 metre deep) including taking out broken tree/branches if found etc complete all as directed.

Material and labour for cement base paint of complete sewage/drainage sump buildings inner & outer by scraping old wall and ceiling surfaces and applying two coats synthetic enamel paint of approved colour over all metal/wooden surfaces complete all as directed.

M&L for framed work such as grills, gratings etc with ends of bars, shoulders and or riveted or forged into spikes, framed guard bars, burred iron doors, ladders framed balasters walk ways, railings, frame work of sewage tanks & similar work conforming to Fe-290 Gde E-165 complete all as directed

M/S S K Electricals Regd

M/S RAJ ENGINEERS

M/S AMBASSADOR ELECTRIC WORKS

M/S ASHOK KUMAR SURI

BMMJ TRADERS AND ENGINEERS