Provn of sets of community toilet Each consisting 10 Urinal Points 03 Wash Basins and 04 WC and water connection with 50 users septic tank and soak well at old air field Srinagar under GE 970 EWS

Amount

Surface dressing not exceeding 15 cm deep of any type of soil complete all as specified and directed by the Engr-in-Charge.

Excavation in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation or for shafts,wells,cess pits,,man holes pair holes etc not exc 10 sqm on plan and not exc 1.5m in depth and getting out in any type of soil complete all as specified and directed by Engr-in-Charge.

Plain cement concrete (1:4:8), type D-2 (using 40mm graded crushed stone aggregetes) as in foundations, filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns , raft and raft beams, sides and soffits ( if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed by Engr-in-Charge.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions on rough finished surface of concrete complete all as specified and directed by Engr-in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders,bresumers, lntels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc for fair finished surfaces complete all as specified and directed by Engr-in-Charge.

RCC, M-25 (Design Mix), using 20 mm graded crushed stone aggregates as in foundation footing, plinth beams, roof beams, lintel beam and mass concrete, complete all as specified and directed by Engr-in-Charge.

RCC, M-25 (Design Mix), using 20 mm graded crushed stone aggregates as in coloumns, pillers piers post and struts etc; complete all as specified and directed by Engr-in-Charge.

RCC, M-25 (Design Mix), using 20 mm graded crushed stone aggregates as in RCC bend, lintels over 1.5 meter span etc, complete all as specified and directed by Engr-in-Charge.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

All as per Serial item No 10 here-in-above but 5mm dia & over and including upto 8mm dia as in stirrups,spacers and binders complete all as specified and directed by Engr-in-Charge.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed by the Engr-in-Charge.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surface, finished even and smooth without using extra cement, complete all as specified and directed by the Engr-in-Charge.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface, finished even and smooth without using extra cement with liquid WPC @ 200 ml per bag of cement, complete all as specified and directed by the Engr-in-Charge.

Preparation of new plastered surface of walls and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surface of ceiling and applying two coats of white wash complete all as specified and directed by Engr-in-Charge.

Preparation of newly plastered surface of walls and applying two coats of cement based paint over a coat of white wash complete all as specified and directed by Engr-in-Charge.

Framed steel work such as in roof trusses, trussed purlin, crane gantries rails and fastening and heavy bracket framing (beam,tee,angle ,channel or flat section) including dIstances pieces ,cleats etc of Fe-410 W , Gde E-250 , complete all as specified and directed by Engr-in-Charge.

Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St. 240 , complete all as specified and directed by Engr-in-Charge.

Plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk) forming holes , without any attachment of Fe- 410-W, Grade E-250, quality -B , complete all as specified and directed by Engr-in-Charge.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt exceeding 22.5cm but not exceeding 30cm long, diameter of neck 16mm to 22mm complete all as specified and directed by Engr-in-Charge.

Preparation of new or previously untreated steel/ iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc primer ,complete all as specified and directed by Engr-in-Charge.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet, 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

S&F of 12mm thick gypsum board fixed in Anodized aluminum snap grid frame work for false ceiling, size of grid 605mmx605mm, runners of size 15x32mm with hangers of 6mm dia GI (up to 1200mm length) adjusting level, fixed to roof by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed by Engr-in-Charge. all as specified. Make: Everest, Armstrong or its equivalent as approved make.

S&F aluminium anodised louvered ventilator using rectangular tuve of size 63.50x25x1.50 mm including 4 mm thick froasted glass and fixed with mosquito frame with jalli complete all as specified and directed by Engr-in-Charge.

Plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pins at joints of 2nd class hard wood, complete all as specified and directed by Engr in Charge

S&F 30mm thick flush shutters, solid core construction with particle board core and plywood, commercial type on both sides with and including decorative laminate type 1, of thickness 0.90mm surface finish colour pattern as approved, fixed with approved adhesive as per manufactures instruction on both faces of shutter bounded edges with plain fillets n.exc 3 Sqm veneer wih lipping/ frame ot match face panels, commercial type on both side complete all as specified and directed by Engr in Charge .

S&F Butt hinges (ISI Marked) 125mm in size, Medium weight, cold rolled mild steel complete all as specified and directed by Engr-in-Charge.

S&F 150mm aluminium handles (ISI marked) extuded febricated type anodised , complete all as specified and directed by Engr-in-Charge.

S&F 200mm size aluminium anodised, barrel tower bolt (ISI marked) of extruded section complete all as specified and directed by Engr-In-Charge.

Aluminium alloy, anodised, sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, 300 mm size complete all as specified and directed by Engr-In-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 150mm complete all as specified and directed by Engr-in-Charge.

Moorum filling under floors/ pavings, laid in layers not exceeding15 CM thick, spread, levelled and rammed/ rolled including watering to required level gradient, complete all as specified and directed by Engr-in-Charge.

M&L for Hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge.

75mm thick, PCC, (1:4:8), type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors, complete all as specified and directed by Engr-in-Charge.

Non skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:6), complete all as specified and directed by Engr-in-Charge.

Glazed ceramic coloured tiles of size 450x300x7mm thick, on vertical surface of walls or such as skirting, dados and risers to step etc set and jointed in neat cement slurry and pointed or coloured cement to match, including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engr-in-Charge.

75mm thick, PCC, (1:3:6), type C-2 (using 40 mm graded crushed stone aggregate) in paving/plinth protection, finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Machine pressed precast conctete interlocking paver block made with electrovabro technology of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, with grey cement & pigment (red colour) and 40 mm thick sand cushioning laid over sub base for fixing interlocking paver blocks , complete all as specified and directed by Engr-in-Charge.

PCC, (1:2:4), type B-1 (using 20mm graded crused stone aggregates) as in coping and like including formwork,weathering, slighting rounded or chamfered angle complete all as specified and directed by Engr-in-Charge.

S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and directed by Engr-in-Charge.

S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/ floors complete all as specified and directed by Engr-in-Charge.

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/ floors complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) bend of any radius complete all as specified and directed by Engr-in-Charge.

S&F 75mm PVC (SWR) bends of any rdius complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed by Engr-in-Charge.

PVC(SWR) floor trap,75 mm dia,plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

Rotational moulded polyethlene three layers water storage tanks 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated alu rod and high density plastic ball, screwed for iron pipe or brass ferrule and fixed all as specified in SSR Part-I, complete all as specified and directed by Engr-in-Charge.

15mm dia Bib taps/ stop cock , cast copper alloy , CP with crutch or butterfly handle fancy type, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engr-In-Charge.

Towel Rail, 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 170gms), complete all as specified and directed by Engr-in-Charge.

S&F Vitreous China wash down water closet pan ( pedestal pattern) , white (EWC) with 'P' or 'S' trap, connection to drain or outgoing pipe, 10 ltr capacity PVC flushing cistern, with brackets for flush tank, PVC connection , 15mm size with PTMT nuts of length 450mm including with all necessary fittings, inlet, outlet pipe connectios and plastic water closet seat cover, closed pattern with recessed bottom cover and mild steel chromium plated hinge complete all as specified and directed by Engr-in-Charge.

Vitreous China half stal Urinal flat back, white (including flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including waste pipe fixing complete all as specified and directed by Engineer-in-Charge.

Vitreous china water closet Squatting Pan "Orissa", Pattern , white size 630 x 450mm with integral foot rest including provision of PCC (1:3:6), type C-1 (using 20mm graded stone aggregate) as in bedding connection to trap, outgoing flushing pipe, anti sypohonage pipe, 100mm bore 'P' or 'S' of pipe etc, complete all as specified and directed by Engr-in-Charge.

S&F Vitreous china wash basins counter oval type of size 460x310x220mm fixed in cooking platform made out of 16 to 18 mm thick granite wtih and including PTMT waste coupling of size 32mm bore and waste pipe as suitable size complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore, health fauset, chromium plated, with flexible tube 8 to 10mm dia and 1m logn and with wall hook complete all as specified and directed by Engr-in-Charge.

S&F, CP brass toilet paper holder with flap complete all as specified and directed by Engr-in-Charge.

PVC connections 15mm dia with PTMT nuts of 450mm long suitable size at both ends, complete all as specified and directed by Engineer-in-Charge.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe 15mm dia , for WHB complete all as specified and directed by Engr-in-Charge.

16-18mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills, cooking platforms and like in CM 1:4 including pointing in white cement 1:2 using marbal dust with admixture of pigment to match with shade of granite including moulding half round and polishing complete all as specified and directed by Engr-in-Charge.

15mm dia Bib taps,cast copper alloy with crutch or butterfly handle fancy type, screwed down, for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge.

Galvanised iron water tubing (ISI marked) 15 mm bore (medium grade) with and including all fittings (ISI marked ) such as sockets, bends, elbows, unions, tees, diminishing pieces etc laid in trenches or fixed to walls/ceiling/ floor , complete all as specified and directed by Engr-in-Charge.

Galvanised iron water tubing (ISI marked) 20 mm bore (medium grade) with and including all fittings (ISI marked ) such as sockets, bends, elbows, unions, tees, diminishing pieces etc laid in trenches or fixed to walls/ceiling/ floor complete all as specified and directed by Engr-in-Charge.

Lagging to pipes used in external water supply or plumbing all round with 25mm thick bounded mineral wool preformed "SNAP ON" pipe sections of density 144 kg/Cum conforming to IS-9842 for 20mm dia GI pipe provided with chicken mesh wire netting 25mm gauge,20mm mesh with 0.01 mm aluminium foil complete all as specified and directed by Engr-In-Charge. Note:- Cost of provision of clamps made to shape from mild steel flat iron of size 8 mm dia x 4 mm including long, nuts and washers with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer for fixing of lagged pipes and other pipes shall be included in the respective items of pipes here-in-before complete all as specified and directed by Engr-in-Charge.

RCC pipe, 150mm dia class, NP3 laid in trenches and jointed with collar complete all as specified and directed by Engr-in-Charge.

Plain cement concrete (1:4:8), type D-2 (using 40mm graded granite stone aggregates) in concrete bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested for pipes of 150mm bore concrete all as specified and directed by Engineer-in-Charge.

Providing precast cement concrete 1:2:4, Type B-0 (using 20mm graded aggregates) as in landing, cover slabs (for manholes etc) chullah, hoods, chajjas, and similar articles with plane face) set in CM 1:4 complete all as specified and directed by Engr-in-Charge

PCC, (1:2:4), type B-1 (using 12.5mm graded crused stone aggregates) as in coping and like including formwork,weathering, slighting rounded or chamfered angle complete all as specified and directed by Engr-in-Charge.

Construction of septic tank in ordinary soil, foundation in PCC (1:2:4), for 50 users, brick work in CM 1 : 4 ( with top of slab at ground level) including necessary excavation and earth work in any type of soil and disposal of surplus soil as directed, RCC manholes covers having 6mm plate embedded all around/fibre reinforced cover with angle iron welded frame complete all as per drg No CESZ/TD-01/2015, Sheet No 1/3 and 2/3,including vent shaft with cowl and sludge chambers etc, complete, all as specified and directed by Engineer-in-Charge.

Construction of soakage well 3 mtr dia and 3.00 mtr deep in ordinary soil below inlet (depth) from inlet pipe to ground level 45 cm, including excavation and earth work in any type of soil, PCC (1:3:6), type C-2 (using 40 mm graded stone aggregates) in foundation, walling honey combed , cover slab of M-25 design mix, including intercepting chamber, screen chamber in brick work in CM 1:4 , RCC cover slab in M-25/ RR masonary, filling with brick bats complete all as per drg No CESZ/TD-01/2015, Sheet No 3/3 and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming, in layers not exceeding 25 cm thick , complete all as specified and directed by Engr-in-Charge.

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in any type of soil complete all as specified and directed by Engr-in-Charge.

Gun metal, globe or gate valve of 25mm dia bore non rising spindle heavy duty with iron wheel head, screwed both end for connection GI pipes complete all as specified and directed by Engr-in-Charge.

M&L for cutting existing 50mm dia steel tubing for altrationns or additions (Each cut measured) and screwing/ inserting new GI Tee 50x50x20mm in position without takig down the existing pipe for taking new connections with all fittings and joints complete all as all as specified and directed by Engr-in-Charge

Steel water tubing, 25mm bore, 'medium grade', galvanised, with all fittings and fixtures including short lengths, bends, elbows, tee, unions etc. laid in trenches/ fixed to wall or Ceiling complete all as specified and directed by Engr-in-Charge.

Rolled mild steel in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps , bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffners , gusset plates , etc conforming to Fe-290 (Gde E-165) complete all as specified and directed by Engr-in-Charge.

Point wiring using FR PVC insulated unsheathed /multistranded copper conductor cable 1.5 sq mm drawn through and including PVC casing and caping ISI marked and of appropriate width as specified, fixed on surface of wall/ ceiling with mild steel sunken box and bakelite sheet 3 mm thick including all fittings such as tees, bend and junction boxes etc complete for one light/ Fan point controlled by one switch, 5 Amps, one way, using cable (1.5 Sq mm for phase and neutral and 1.5 sq mm earthing), complete all as specified and directed by Engr-in-Charge.

All as per above Srl Item No 80 but here-in-before switch socket combination 2 in 1, 3 pin 5/15 Amp on Independent board using cable (2.5 Sq mm for Phase & neutral and 2.5 Sq mm for earthing) complete all as specified and directed by Engr-In-Charge.

Ceiling rose surface bakelite, 3 terminal size 50 x 65 mm surface type, complete all as specified and directed by Engr-in-Charge.

S&F switch piano flush button type one way 5 Amp complete all as specified and directed by Engr-in-Charge.

Lamp holder insulated body with back plate suitable for batten fitting/ angle fitting/ CFL/LED lamp , complete all as specified and directed by Engr-in-Charge.

Switch socket combination outlet 5 pin, 5/15 Amp, 230 Volts flush type, complete all as specified and directed by Engr-in-Charge.

Exhaust fan 380 mm sweep 900rmp heavy duty dia with louvers including grouting of bolt of suitable size for fixing of frame and connecting with electric circuit from ceilig rose with the help of PVC cable of 3 core 40/0.0076 complete all as specified and directed by Engineer-in-Charge. Make : Bajaj / Havells/Usha.

Sheet metal enclosure factory made (double door) shutter type for DB SPN, 240 Volts, 8 ways with suitable rated bus bar, neutral link, earth bar complete all as specified and directed by Engr-in-Charge.

S&F MCB SPN 6-32 Amps 230 volts, C curved 50 Hz AC 10 KA complete all as specified and directed by Engr-in-Charge.

S&F MCB SP 6-32 Amps 230 volts, C curved 50 Hz AC 10 KA complete all as specified and directed by Engr-in-Charge.

S&F Energy efficient LD street light luminaire 45 watts capacity compriss a die-cast aluminium housing including elect connectins complete all as speified and directed by Engr-in-Charge. (Make - Bajaj at No BRTFG 45 W LED I or its equivalent as specified make)

Street light bracket made out of 40mm dia galvanised tube, medium grade, 1.2mtr long, bend to shape to the required degree including painting with two coats of synthetic enamel aluminium paint over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with GI steel earth plate electrode 600x600x6mm burried directly in ground not less than 2.25 mtr deep below normal ground level with top edge of earth plate not less than 1.5mtr below normal ground level connected to the Galvanised iron wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised steel all as shown on electrical plate No 5 of MES Sch 2009 Part-I connected to earthing test point and testing on completion with and including necessary excavation and earthwork, earth electrode, earthing lead from electrode to eqpt/sub stn , adequated quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 using 20mm graded black trap/granite/basalt stone aggregate, 40mm thick cover reinforced with 8mm dia bar 4 Nos both way with 12mm dia round bar handle, GI light grade protection pipe 15mm bore with funnel and wiremesh and 15mm dia GI light grade earth lead protection pipe complete all as specified and directed by Engr-in-Charge. Notes:- (i) On testing after completion if the desired resistenance is not obtained the contrator shall redo the earthing without any extra cost to the department.

S&F 18/20 watts 4' long surface mounted LED batten integrated electronic driver complete all as specified and directed by Engr-in-Charge (Make - Bajaj Cat No BCLSB 18NW or its equivalent as specified make)

S&F of Electric water Geyser, Storage type, of capacity 25 Ltr, BEE 5 Star rating, body of ABS plastic material, copper inner tank, auto cut, Adjustable temperature, safety valve, thermal cut out, input voltage 230 Volt, 1500/2000 watts capacity including all fittings 4 sets of nut, bolts and washers of minimum dia 10mm, grouting in wall, 2 Nos PVC connections 45 cm long suitable for Hot/Cold water and two No's brass CP 15mm bore stop valve, 01 No NRV, 01 PRV, 01 Plug top 16 Amps and making all electric and water connections complete all as specified and directed by Engr-in-Charge.

S&F LED lamp 7/9 w capacity white in colour suitable for regular holder all as specified and directed by Engr-in-Charge.

M&L for cutting of road crossing/ PCC hardstanding for laying of cable/ pipe and making good the existing surface with same finishing material including removing of the surplus soil outside of defence land complete all as specified and directed by Engr-in-Charge.

Sand cushioning to underground cables 8cm thick before laying cable and 15cm thick after lying and streching the cable, complete all as specified and directed by Engr-in-Charge. Note :- For payment purpose punned thickness 18cm shall be measured.

Brick (well burnt locally available sub class `B') cable cover laid over sand cushioning to cable in trenches keeping width of brick parallel to the length of cable all as specified and directed by Engr-in- Charge.

Supply, laying, Jointing and testing LT cable XLPE of insulated, screened PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade cross section area 16 sqmm 2 core laid in trenchers, duct, passing through pipe, fixed to poles complete all as specified and directed by Engr-in-Charge.

S&F GI Pipe light grade ISI marked including all fittings on wall or laid on floor as reqd position of size 50 mm bore for protection of cable in trenches/under road complete, all as specified and directed by Engr-in- Charge.

M/S Alam Construction

M/S LUCKY BUILDERS

Javeed And Co