REPAIR / MAINT TO SUNKEN FLOOR TREATMENT, PLUMBING, PLINTH PROTECTION AND OTHER ALLIED WORKS

Amount

SCHEDULE A BOQ

S&F in repairs Vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor including provision of lime concrete bedding all as specified and as directed.

S&F PVC (SWR) S trap 110mm bore Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

M&L Bib Cock with wall flange screwed down screwed for iron pipe 15mm bore CAT Part No QT F2006151, HT F3001151 of CERA or equivalent to Parryware/Hindware including taking existing one complete as directed by Engr-in-charge.

S&F PVC Dual flush ceramic colour, low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements Including taking down existing one complete all as specified and as directed by Engineer-in-Charge Make/Cat Part No:- 21029 of hindware or equivalent approved make

M&L PVC connection 15 mm size with PTMT nuts of length 450 mm including taking existing one complete as directed by Engr-in-charge.

M&L Angular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, CAT Part No QT F2006202, HT F3001202 of CERA or equivalent to Hindware/Parryware including taking down existing one complete as directed by Engr-in-charge.

M&L Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer, 15 mm thick in Cement Mortar 1:6 complete including dismantling of existing tile and disposal off to outside MD land all as specified and as directed.

M&L Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including backing coat of 10 mm thick in Cement Mortar 1:4 complete including dismantling of existing tile and disposal of to outside MD land all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size exc 0.09 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as directed.

M&L Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado including 10mm thick 1:3 backing coat including taking down existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Taking down chowkhat or frame(wooden/steel) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S&F Mild steel work in framed work such as grills and similar work including framed guard bars, barred iron doors, ladders, framed balusters etc., including of fixing of sheet steel or other covering to doors etc., to be prepared for hanging /sliding with or including either hooks or hinges or steel hanging door fittings etc., confirming to Fe 410-0 or Fe 310-0 work complete including Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified .

S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

S&F Butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed.

S & F Aluminum handles cast type anodised 150 mm long complete all as specified and as directed.

Supply and fixing 200 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed.

S & F in repairs Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, comercial type on both faces complete all as specified and directed.

S&F Factory made second class hard wood 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

M & L Preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Note for item No 22 :- (a) All synthetic enamel paint, plastic emulsion paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

S&F 150mm extruded aluminum alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing 100 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed.

S&F 250mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminum alloy and fixed complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete all as specified and as directed.

S&F in repairs 300mm, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing complete all as specified and as directed.

M&L PVC bends 110mm bore including taking down existing one complete all as specified and as directed.

M&L PVC (SWR) 110mm junction (single T) equal or unequal provided with access door including taking down existing one complete all as specified and as directed.

M&L PVC (SWR) 110mm junction vent cowl all as specifed including taking down existing one complete all as specified and as directed.

S&F PVC (SWR) branch piece double (double Y) 110mm bore equal or unequal provided with access door including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) branch piece single (single Y) 110mm bore equal or unequal provided with access door including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F Wall mounted Shower Arms 200mm long flat shape for wall mounted shower with flange including taking down complete all as specified and directed (Make :CAT Part No-F7040102 of CERA or equivalent make of parriware /hindware..

S&F in repairs Overhead Shower ø120mm Round Shape with 3 Flow (ABS Body Chrome Plated with Gray Face Plate) complete all as specified and as directed. (Make :CAT Part No- F 7020305AB of CERA or equivalent make of parriware /hindware..

M&L in repairs Chromium plated wall mixer with provision for over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges complete all as specified and directed. Make:- QT F2002401 of CERA or equivalent in Parryware /Hindware / ESS-ESS

S&F PVC (SWR) P trap 110 mm bore Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

M&L Pillar taps 15mm bore CP with capstan head screwed down high pressure screwed for iron pipe Cat Part No QT F2006101 of CERA or equivalent to /Parryware/Hindware including taking down existing one complete as directed by Engr-in-charge.

M&L WHB, vitreous china (flate back or angle back type) of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe Complete including taken down existing one all as specified .

S&F 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down existing one complete all as specified and directed by Engineer- In - charge

M&L 32 mm low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm for WHB Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

M&L 40 mm low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm for WHB Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

M&L 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing complete all as specified and as directed.

S&F PVC (SWR) 75mm bore junction vent cowl including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) 75mm bore junction single (single T) equal or unequal provided with access door including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) branch piece single (single Y) 75mm bore equal or unequal provided with access door including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F in repair CP Soap dish CAT Part No- F 5007106 of CERA or equivalent make of Parryware /Hindware all as specified and as directed.

S&F in repair Towel rail 24" long for wash basin (Make : CAT Part No- F 5007103 of CERA series or equivalent make of hindware / parryware all as specified and as directed.

S&F 600 x 450 mm bevelled edge mirror fixed with 04 Nos Stainless steel studs including taking down existing one complete all as specified and as directed.

M&L Glass shelf assembly including taking existing one complete as directed by Engr-in-charge. (Make : CAT Part No F5005101 continental of CERA series or equivalent make of Parriware /Hindware all as specified and as directed.

M & L Bullnosed chequered cement concrete tiles 32cm x 30cm x 30mm thick machine pressed set jointed and pointed in neat cement slurry as in treads and cut and polished using grey cement and pigments over screed bed or bedding layer of mortar 15mm thick for laying floor fnishes in cement mortar (1:4) including taking down existing tiles complete all as specified and as directed by Engineer-in Charge.

M&L taking down cement plaster on brick or stone walls, or concrete or ceilings etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, removal and depositing serviceable materials complete all as specified and directed.

M & L cement concrete tiles 20cm x 20cm x 20mm thick machine pressed set jointed and pointed in neat cement slurry on vertical surfaces as in skirting, dados and risers of steps and cut and polished using grey cement and pigments over backing coat of mortar 10mm thick for laying floor fnishes in cement mortar (1:3) including taking down existing tiles complete all as specified and as directed by Engineer-in Charge.

M&L Rendering 15 mm thick in cement mortar 1:6 on fair face of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L Preparation of new plastered surfaces wall applying two coat of OBD over a coat of alkali resistant priming paint complete all as specified and directed.

S & F in repairs sink cock of 15 mm bore (wall mounted) with 170mm long swivel spout and wall flange screwed down for iron pipe (make : Cat No QT F2006251 HT F3001251 of CERA or equivalent make of Hindware/ Parryware complete all as specified and directed.

S&F in repairs Sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410 mm x 330mmx160mm, including 40 mm waste coupling brass chromium plated,discharge pipe complete all as specified and directed.

S&F in repairs Waste coupling of PTMT (half or full threaded) of 40mm bore dia of discharge pipe . (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and directed.

S&F in repairs Plate rack of size 65 cm x 96 cm made of stainless steel, complete all as specified and directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided for complete all as directed.

M&L Plain cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in roof kerbs, benching rounded or chamfered on edge all as specified complete all as directed.

M&L 75mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates), as in plinth protection/path/hardstanding including making joints @ 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement including demolition of existing damagd cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness and rubish material shall be disposal to out side MD land complete all as specified and as directed.

M&L Taking down steel tubing 15 mm bore and connections including cleaning and refixing of old GI tubing 15mm bore including connections in new or old position (wall, ceiling & floor complete all as specified and as directed

M&L Taking down steel tubing 20 mm bore and connections including cleaning and refixing of old GI tubing 20mm bore including connections in new or old position (wall, ceiling & floor complete all as specified and as directed.

Note for Item No 73 & 74 :- The unit rate quoted is inclusive for necessary fittings of suitable sizes required for re-connection.

M&L Hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface including removal of existing complete all as specified and directed.

Demolition of cement concrete (reinforced) in of any description and in any position and removal of debris out of MD land complete all as specified and directed.

M&L 100 mm thick Plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate ) as in hard standing including demolition complete all as specified and directed.

M&L PVC bends 75mm bore including taking down existing one complete all as specified and as directed.

Supply and fixing in repairs factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension,including Pinhead Glass with thickness of 4mm required for fixed & louvers strips, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in imension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

M&L in repairs Granite work (of any type) 18 to 20mm thick (table rubbed and polished including round edge) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L plastic water closet seat cover for EWC with flat bottom and cover and mild steel chromium plated hinging device including taking down damaged existing one complete as directed by Engr-in-charge.

Treatment of the sunken floor slab comprises of the following specification and all as specified. Make :- Dr Fixit/ M/s Sika india Pvt Ltd/ STP Ltd/ M/s Fosroc Chemicals

(a) Demolition of cement concrete filling of any description in sunken portion in toilet and removing debris outside MD land.

(b) Cleaning the sunken/ lowered portion of RCC slab surfaces (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding conc to achieve proper sploe including cutting holes in bricks or RCC wall for spout

(c) Rendering of uneven surfaces with 10mm thick CM 1:4 mixed with integral water proofing compound @ 3% by wt of cement consumed. Fill it with water and check dampness and seepage. Where dampness/ seepage is noticed, nozzles shall be fixed and grouting carried out. (Quoted rate shall be deemed to be inclusive for WPC )

(d) All junctions points of side wall where CI/ GI pipes are passing through shall be sealed with epoxy putty.

(e) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.

(f) M&L for applying two coats of polymer modified cementious water proof coating as per manufactures instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed

(g) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound 3% by wt of cement consumed as per manufacturers specification including rounding of corners and junctions sloping towards spout. (Quoted rate shall be deemed to be inclusive for WPC )

(h) PCC 100 mm thick 1:5:10 type E2, using 40mm graded stone aggregate complete all as specified

(j) PCC 40 mm thick 1:2:4 type B-0 using 12.5 mm graded stone aggregate complete all as specified

Note for item No 83 to 92 :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage, seepage and to the entire satisfaction of GE. Test shall be done in presence of reps of Engineer-in-Charge and record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing is include in the rates quoted above. The contractor shall produce guarantee bond giving TEN years guarantee for the waterproofing work from the date of completion of subject work. A sum of 3% of the quoted amount shall be retained out of the final bill amount as security deposit for waterproofing work. The amount shall be released to the contractor after satisfactory expiry of ten years guarantee period from date of completion of subject work.

S&F False ceiling using GI snap grid size 60x60cm with main runner 38x24,wall angle & cross tee 29x24mm wall angle 24x24mm suspended with 4mm dia GI Wire fixed with steel dash fasteners carrying max load upto 8.1 Kg/Sqcm with 4mm thick designer ceiling board (Lake & Hill) all as per Everest regular T-2430 or equivalent (Make-Ramco/Charminar/Armstrong) including dismantling all as specified and as directed.

S&F Aluminium extruded section body door closer hydraulically regulated,designation No.3, universal type, suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 kg and fixed including taking existing one complete as directed by Engr-in-charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel covert governing pivot made of brass, other parts made of mild steel heavy duty including taking down existing wire cloth all as specified and directed.

S & F 9mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work including taking down existing one complete all as specified and as directed.

S&F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved including taking down existing one complete all as specified and as directed.

S & F in repairs 18/19mm thick Particle board for insulation purposes, fixed with screws to timber framework complete all as specified and as directed.

S&F Stainless steel thali basket of size 600x 500x 100mm Including taking down the existing one complete Make : Butterfly or equivalent make as per list of makes in PS)

S&F Stainless steel cutlery basket of size 530 x 505 x 100 mm Including taking down the existing one complete Make : Butterfly or equivalent make as per list of makes in PS)

S&F Stainless steel spring hinges of size of approved pattern and make suitable for base/wall unit of modular kitchen Including taking down the existing one complete (Make : BIR SS or equivalent make as per list of makes in PS)

S&F Magnetic catches with 8mm dia steel ball and brass body and striking plate including letting in repairs complete all as specified and directed.

S&F Stainless steel plain basket of size 530 x 505 x 100mm Including taking down the existing one complete. Make : Butterfly or equivalent make as per list of makes in PS

S&F Stainless steel bottle basket of size 200x 508x 431mm B35e. Make : Butterfly or equivalent make as per list of makes in PS

S&F Stainless steel telescopic slider of 500 mm of approved pattern and make suitable for drawer in base unit of modular kitchen including taking down the existing one complete all as specified and directed.

S&F Brass continuous(Piano)hinge 30mm widthof flap, bright finish of electrolyte complete all as specified and as directed by Engneer-in-Charge

S&F Stainless steel handles of size 150 mm of approved pattern and make suitable for Base/Wall unit of modular kitchen Including taking down the existing one complete (Make : Spykar or equivalent make as per list of makes in PS)

S&F Brass 4 lever cupboards locks grade I size 65 mm complete including taken down existing one complete all as specified and as directed by Engineer-in-Charge

S&F 40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished complete including taking down existing one all as specified and as directed.

M&L 25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings including taking existing one complete as directed by Engr-in-charge.

M&L Mild steel powder coated brackets for holding the drapory rod and fixed to wall with MS screw including taking down existing one complete as directed by Engr-in-charge.

Supply and Fixing in repairs Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapaery rod as directed.

S&F PVC body cabinet mirror of size 500 X 400 MM of approved design and pattern Including taking down existing one complete all as specified and as directed by Engineer-in-Charge . (Make: Cat Part No 556 of Prayag or its equivelent in ESSCO/ Kohler as approved by GE

S & F in repairs second class hardwood Plain fillets square, rectangular or triangular in section of area Exc 3 sqcm and n exc 6 sqcm, clean sawn, secured with nails or brads complete all as specified and as directed.

S & F in repairs 15 mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

M&L in repairs Doom grating 125mm dia with waste hole of PTMT(minimum weight 40gms) Including taking down existing one complete all as specified and as directed by Engneer-in-Charge.

D.R ASSOCIATES (BID ID -3171327)

KRISHNA ENTERPRISES (BID ID -3166031)

GMS Builders (BID ID -3171175)

SKM CONSTRUCTION (BID ID -3170986)

T C KARUNANITHI (BID ID -3166967)

KAARTHIC BUILDERS (BID ID -3170848)

T SANJEEV KUMAR (BID ID -3167603)

p.chinnasamy (BID ID -3167989)

Sri ASK Constructions (BID ID -3171081)

K S MUTHU CONSTRUCTTIONS (BID ID -3168559)

G Perumal and co (BID ID -3171237)