Addition/alteration to Bldg No P-33 and minor work provn of toilet block at NFS site- (Signal Section) at AF Stn Darbhanga under GE (AF) Bihta.

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed by Engr-in-Charge

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) any thickness, incluing cover fillets, complete all as specified and as directed by Engr-in-Charge

Dismantling boarding, any description, fixed in any position complete all as specified and as directed by Engr-in-Charge

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and as directed by Engr-in-Charge

Taking down chowkats with shutter (without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sqm each, complete all as specified and as directed by Engr-in-Charge

Taking down chowkats with shutter (without taking off shutters from the frames) not exc 1.5 sqm each, complete all as specified and directed.

Taking down shutter and refixing in the same opening of any description exc 2sqm each, complete all as specified and as directed by Engr-in-Charge

Taking down plastering in cement lime or cement mortar complete all as specified and as directed by Engr-in-Charge

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed by Engr-in-Charge

Demolition Reinforcement Cement Concrete as in roofs floors/(other than ground floors) beams, staircase, landing, chajjas and similar suspended works complete all as specified and as directed by Engr-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge

Surface excavation n exc 30cm deep and averaging 15cm and getting out in Soft/ loose soil complete all as specified and as directed by Engr-in-Charge

Excavation in trenches n exc 1.50m wide and n exc 1.50m deep and getting out in soft/ loose soil complete all as specified and as directed by Engr-in-Charge

M & L for PCC 1:4:8 type D2 (using 40mm graded stone aggregates) as in foundations, filling mass concrete complete all as specified and as directed by Engr-in-Charge

M&L for brick work with sub class B bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engr-in-Charge

M&L for MS TMT bars 8mm dia and over cut to length, bent to shape required, including cranking, bending,spirally for hoping for columns, hooking end and binding with and incl mild steel wire (annealead) not less than 0.9mm dia, complete all as specified and as directed by Engr-in-Charge

Ditto but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders complete all as specified and as directed by Engr-in-Charge

Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed aggregate) mixed with water proofing compound as in complete all as specified and as directed by Engr-in-Charge

Supply only Liquid water proofing compound complete all as specified and as directed by Engr-in-Charge

M&L for RCC Nominal Mix 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in Beams, cantilevers, bressummers lintels over 1.5m span, complete all as specified and as directed by Engr-in-Charge

Use and waste of formwork to sides and soffits of, bressummers lintels, rough finished complete all as specified and as directed by Engr-in-Charge

M&L for RCC slab supported on columns, beams, wallas etc in roofs, landing etc and like Type B 1 (1:2:4) (20mm gardedstone agg) Nominal Mix, complete all as specified and as directed by Engr-in-Charge

Providing precast cement concrete 1:2:4 type B0 (12.5mm graded aggregate)louvres and jallies 15mm thick in cluding all mouldings set in CM 1:4 complete all as specified and as directed by Engr-in-Charge

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping), incl fair finish surface complete all as specified and as directed by Engr-in-Charge

Use and waste of formwork to edges of concrete flats, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide, complete all as specified and as directed by Engr-in-Charge

Rendering 15mm thick on other than fair faces on brick masonary or concrete surfaces in cm 1:6 finished complete all as specified and as directed by Engr-in-Charge

M&L 15 mm thick rendering on fair faces of external wall of brick masonary or concret surfaces in cm 1:4 finished complete all as specified and as directed by Engr-in-Charge

Prepration of newly plastered external surface of wall and applying two coat of cement base paint over a coat of chalk whiting complete all as specified and as directed by Engr-in-Charge

M&L for Prepration of newly plastered on walls complete all as specified directed and applying two coat of oil bound distemper over a coat of alkali resistant priming paint, complete all as specified and as directed by Engr-in-Charge

Returning, filling in, including spreading, levelling, waterning and well ramming in layers not exceeding 25cm thick , complete all as specified and as directed by Engr-in-Charge

Removing excavated material n,exc 50 m and depositing where directed at a level n, exc 1.5m above the starting point complete all as specified and as directed by Engr-in-Charge

M & L for hard core (broken bricks) of gauze n exc 63mm deposited, spread in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-Charge

M & L for PCC 1:3:6 type D2 (using 40mm graded stone aggregates) as in foundations, filling mass concrete complete all as specified and as directed by Engr-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, complete all as specified and as directed by Engr-in-Charge

M&L 15mm thick screed in CM 1:6 on brick or concrete surfaces for fixing of tiles as in floor complete all as specified and as directed by Engr-in-Charge

M&L Chequered cement concrete tiles 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors With grey pigment cement and pigment complete all as specified and as directed by Engr-in-Charge

M&L for Non-Skid ceramic coloured tiles (Premium quality) 7 to 8 mm thick area of each tiles exc 0.18sqm but not exc 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed by Engr-in-Charge

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed by Engr-in-Charge

S&F coloured Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and as directed by Engr-in-Charge

M&L steel work in roof trusses (framed)trussed purlins, crane gantries rails and fastenings and heavy bracket framing (beam, tee, angle channel or flat sections ) includingdistance pieces cleats etc Fe-410 W complete all as specified and as directed by Engr-in-Charge

S&F RMP sheeting 1.5 mm thick with 1.5 corrugation side lap fixed with L-type or J type or cranked hook bolts in roof, wall etc complete all as specified and as directed by Engr-in-Charge

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated /plain steel sheet 0.50 mm thick of any colour as approved by Engr-in-Charge/GE having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engr-in-Charge

S&F Anodised aluminium snap grid frame work wih 20x25mm 'T' and 20x20mm 'L' section with grid size of 605x605mm including with necessary 3.15mm GI wire as in suspended etc complete all as specified and as directed by Engr-in-Charge

S&F Gypsum ceiling board 60x60cm x12mm thick (pre-finished decorative type) in ceiling fixed with screw as per manufacturers instruction, or complete all as specified and as directed by Engr-in-Charge

S&F anodised aluminium frame for doors, windows, ventilators, partations with one or more rebates including joining cleat for fixing etc, complete all as specified and directed by Engr-in-Charge.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) each shutter. hinges type B-21100mm long (2 no.) suitable handle (1no.) complete all as specified and as directed by Engr-in-Charge

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each shutter, hinges, (03 Nos in each shutter) anodized sluminium snap beading screws etc anodised aluminium snap beading screws etc, complete all as specified and directed by Engr-in-Charge.

S&F Sheet glass 5.5 mm thick ordinary quality and glazing with Aluminium beading with rubber neoprene packing square exc 0.5 sq.m in each pane, complete all as specified and directed by Engr-in-Charge.

S/F mortice locks of 100mm size vertical of 4 levers, aluminium body fixed to aluminium works, complete all as specified and directed by Engr-in-Charge.

S/F in repair mortice locks of 100mm size vertical of 4 levers, aluminium body fixed to aluminium works, Complete all as specified and directed by Engr-in-Charge.

S&F for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavey duty and fixed to aluminium door, complete all as specified and as directed by Engr-in-Charge

S&F in repair Door closer hydraulically regulated designation No 1 universal type, suitable for door shutters up to 851mm to 1000mm in width and of weight between 61 to 80 kg Aluminium body complete all as specified and as directed by Engr-in-Charge

S&F 4 mm Figured glass, pin head type and to be fixed in Aluminium frame work with rubber neoprene packing and aluminium beading etc complete n exc 0.5 sq. m in each pane complete all as specified and as directed by Engr-in-Charge

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed by Engr-in-Charge

M&L for roof sheets stays, window guard bars, plain let in and fixed independently in wooden frames L or T section support for shelves etc., and similar articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed by Engr-in-Charge

As per item No 55 but fixing only

M/L 2nd class H/wood chowkhats, plain, solid, straight, wrought, framed, rebate on the solid,rounded or chamfered put together with glue pinned at joints complete all as specified and as directed by Engr-in-Charge

S&F 30 mm thick flush shutter , solid core construction ,with block board core and plywood face panel ,commercial type on both side complete all as specified and as directed by Engr-in-Charge

S&F 30 mm 2 nd class hardwood Glazed and skeleton shutters, divided into squares, with plain, chamfered or roun ded, mitred and rebated sash bars, any numbers rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed by Engr-in-Charge

M&L for Hold fast for fixing of chowkats and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and as directed by Engr-in-Charge

S&F mild steel medium weight cold rolled butt hinges 100 mm long complete all as specified and as directed by Engr-in-Charge

S&F aluminium anodised, barrel tower bolt of extruded section 150mm long complete all as specified and as directed by Engr-in-Charge

S&F 125 mm long aluminium handle, cast type, anodised complete all as specified and as directed by Engr-in-Charge

S&F aluminium alloy anodised sliding door bolt with hasp staple (bolt type), 250 mm long,and fixing clip of sheet cast or extruded section or fixing bolt cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge

S&F 20mm thick 2nd class Boarding, fixed with nails in any situation Planed one side with butt joints complete all as specified and as directed by Engr-in-Charge

M&L Second class hard-wood in scantlings clean sawn complete all as specified and as directed by Engr-in-Charge

M&L preparing surface of wood and wood based materials new or old, of any description and girth, not otherwise described and treated with creosite complete all as specified and as directed by Engr-in-Charge

M/L two coats of synthetic enameled painting over a coat of pink primer to wooden surfaces of any description exc 10 cm width or girth complete all as specified and as directed by Engr-in-Charge

Preparation of steel surfaces of any description over 10 cm width or girth and applying 2 coats of synthetic enamel paint over a coat of red oxide zinc chrome primer , complete all as specified and as directed by Engr-in-Charge

M&L for Cutting holes in brick walls built in cement mortar exc. Half brick but not exc one brick for inserting holdfasts and making good dismantled portion in cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in tranches or in floors complete all as specified and as directed by Engr-in-Charge

S & F 110mm bore PVC (SWR) bends complete all as specified and as directed by Engr-in-Charge

S&F harrison rails mild steel chromium plated with fixing brackets stops rollers etc complete all as specified and as directed by Engr-in-Charge

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:4 complete all as specified and as directed by Engr-in-Charge

M&L for brick work with sub-class “b” bricks, straight or curved on plan to any radius in half brick thick built in cm (1:4) complete all as specified and directed.

M&L for Prepration of newly plastered on walls complete all as specified directed and applying three coat of white washing, complete all as specified and as directed by Engr-in-Charge

M&L 5mm thick rendering on ceiling or concret surfaces in cm 1:3 finished complete all as specified and as directed by Engr-in-Charge

M&L for Prepration of newly plastered on ceiling complete all as specified directed and applying three coat of white wash, complete all as specified and as directed by Engr-in-Charge

M & L 100 thick PCC 1:3:6 type B2 (using 40mm graded stone aggregates) as in base course to floor finish complete all as specified and as directed by Engr-in-Charge

M & L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate including finished surface even & smooth without using extra cement as in plinth protection complete all as specified and as directed by Engr-in-Charge

S & F PVC door with chowkhats frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supply & fixing in opening as per specification & drawing complete all as specified and as directed by Engr-in-Charge

S & F factory made solid panel PVC door shutter 30mm thick (style) make "RAJSHRI" consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed tothe stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixed to frame at site complete as directed of Engr-in-Charge or Manufacturer's specification and drawing.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed by Engr-in-Charge

S/F 3mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-Charge

Preparation of new steel surfaces and applying 2 coats of synthetic enamel paint over a coat of red oxide zinc chrome primer primer, complete all as specified and as directed by Engr-in-Charge

Use and waste of formwork to edges of concrete flats, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls horizontal or sloping and similar work exc 5 cm but n exc 10 cm wide, complete all as specified and as directed by Engr-in-Charge

M&L for rendering 10 mm thick in CM 1:4 on wall to receive tile complete all as specified and as directed by Engr-in-Charge

M&L for Glazed ceramic coloured tiles in vertical surfaces 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed by Engr-in-Charge

S&F 20mm Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed in repairs, complete all as specified and as directed by Engr-in-Charge

S & F vitreous china wash down water closet pan (pedestral pattern) white including fixing to flushing cistern and flush pipe and plastic water closet seat cover black closed pattern with flat bottom and cover and mild steel hinging device. complete all as specified and as directed by Engr-in-Charge

Supply and fixing PVC flushing cistern, white, 10ltr capacity with 32mm dia flush pipe any lenth fixed to water closed complete all as specified and as directed by Engr-in-Charge

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including brackets including cutting for and pinning in ends of brackets or erecting stand including 32 mm waste coupling and Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engr-in-Charge

S&F 15mm Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed by Engr-in-Charge

S&F Fancy type Stop valves angle /concealed 15mm bore, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engr-in-Charge

S&F fancy type Bib taps, cast copper alloy 15mm dia with capston head handle, screwed down, screwed for iron pipe complete all as specified and as directed by Engr-in-Charge

S&F Brass chromium plated Tublar towel rail 20mm dia D type 60 cm long between flanges complete all as specified and as directed by Engr-in-Charge

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and as directed by Engr-in-Charge

S&F of 16mm 3 layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN16 ) UV stablized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or in floors etc complete all as specified and as directed by Engr-in-Charge

S&F 20mm dia Unplasticised PVC pipes of pressure rating 10kgf/cm2 fixed complete to wall ceilings or in floors complete all as specified and as directed by Engr-in-Charge

S&F Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and as directed by Engr-in-Charge

M&L 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by Engr-in-Charge

M&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed by Engr-in-Charge

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joint anf fixing adhessive, fixed to walls complete all as specified and as directed by Engr-in-Charge

S & F 75mm bore PVC (SWR) band complete all as specified and as directed by Engr-in-Charge

S & F 110mm bore PVC (SWR) junction double (double T) equal or unequal complete all as specified and as directed by Engr-in-Charge

S & F 75mm bore PVC (SWR) junction double (double T) equal or unequal complete all as specified and as directed by Engr-in-Charge

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and as directed by Engr-in-Charge

S& 500 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by Engr-in-Charge

M&L 20mm bore of pipe Cutting existing steel tubing for alterations or additions (Each cut measured) complete all as specified and as directed by Engr-in-Charge

S & F Ball in repair 20mm brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by Engr-in-Charge

Taking down carefully aluminium/copper wiring/power pont wiring(light,fan,call bell,socket or power circuits)complete and making good the disturbed surfaces of walls,ceiling etcincl painting with same colour of the back ground complete all as specified and as directed by Engr-in-Charge.

Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store complete all as specified and as directed by Engr-in-Charge Note:- To be measured only when found serviceable in all respects complete for reuse.

Material and labour for point wiring for One light point with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, ISI marked, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, ISI marked, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick with 3 mm thick plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed including takin down old/unsv wire complete all as specified and as directed by Engr-in-Charge (a)One light/fan point controlled by one way switch.

(b) 3pin 5 Amp socket outlet on independent board complete all as specified and as directed by Engr-in-Charge.

(c) 3 Pin 5 Amp socket outlet on same board complete all as specified and as directed by Engr-in-Charge.

All as per item No 115 but 3 pin 15 Amp socket outlet on indenpendednt board with 2.5 Sqmm cable complete all as specified and as directed by Engr-in-Charge.

S&F Switch Socket conmbination 2 in 1 3 pin 5 Amp and 3 pin 15 Amps flush type universal complete all as specified and as directed by Engr-in-Charge.

S&F Socket flush type 5 pin 5 Amps shutter complete all as specified and as directed by Engr-in-Charge.

Switch Piano, flish button, single pole one way, 5 Amp,230 Volts complete all as specified and as directed by Engr-in-Charge.

Ceiling rose surface bakellite of three terminals complete all as specified and as directed by Engr-in-Charge.

S&F Sheet metal enclosre for MCB DB SPN 6 way double door 240 Volts with 200 Amps rated bus/bars complete all as specified and as directed by Engr-in-Charge.

S&F MCB SPN 63 Amp ISI marked convient to 'C' Curve breaking capacity 10 KA complete in repair complete all as specified and as directed by Engr-in-Charge Make:- Havells/Legrand/Hager.

S&F MCB Single pole 240 Volts 6-32 Amp ISI marked convienent to 'C' Curve breaking capacity 10KA complete all as specified and as directed by Engr-in-Charge Make:-Havells/Legrand/Hager.

S&FSingle pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amp complete all as specified and as directed by Engr-in-Charge

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level (with top edge of earth plate not less than 1.5 metre below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick precast RCC cover in 1 : 2 : 4 type B1 with 3 Nos 8 mm dia TMT bars both ways with 12mm dia round bar handle complete all as specified & directed by Engineer-in-Charge. Note:- Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item and additional earth strip/protection pipe etc. if any required at site shall be measured and paid for separately under appropriate item of Schedule `A’

Material and labour for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 4.0 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade, ISI marked complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing surface complete all as specified and as directed by Engr-in-Charge.

Supply and fixing LED lights fitting 1x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engr-in-Charge.

Supply and laying & testing cable XLPE insulated heavy duty electric cables with aluminium conductor, 1100 volts grade, cross sectional area 35 Sq mm 3.5 core including necessary cable lugs, bolts, nuts and washers complete all as specified and directed. Make:- Nicco/Plaza/Gloster/Havells/polycab

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr deep in loose / soft soil and getting out for under ground cable / erection of poles, stays etc complete all as specified and as directed by Engr-in-Charge.

Returning, filling in including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick complete all as specified and as directed by Engr-in-Charge.

Removing of excavated material n, exc 50 mtr away and depositing where directed at a level n, exc 1.5 mtr above the starting point complete all as specified and as directed by Engr-in-Charge.

M&L for laying of bricks subclass ‘B’ old size laid flat perpendicular to the direction of cable for protection of cable complete all as specified and as directed by Engr-in-Charge.

M&L for sand cushioning for cable with river washed sand and pinning to provide required cover as per SSR Part –I complete all as specified and as directed by Engr-in-Charge.

Supply and fix GI pipe of 40 mm light grade on pole , ISI marked ,of specified sizes including necessery pipe ,fittings , MS clamps, bolts , nuts etc., complete all as specified and as directed by Engr-in-Charge.

S&F Sheet metal enclosre for MCB DB SPN 4 way double door 240 Volts with 200 Amps rated bus/bars complete all as specified and as directed by Engr-in-Charge

Supply and fix GI pipe of 25 mm light grade on pole , ISI marked ,of specified sizes including necessery pipe ,fittings , MS clamps, bolts , nuts etc.complete all as specified and as directed by Engr-in-Charge

Material and labour for sub main wiring with 2.5 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 2.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade, ISI marked complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing surface complete all as specified and as directed by Engr-in-Charge

Cutting walls any type, making holes for fixing of exhaust fan any size or sweep and making good surface with fine plastering and finishing and colouring with existing colour matching complete all as specified and as directed by Engr-in-Charge

Supply and fixing Exhaust fan of 300 mm sweep,1400 RPM,230/240V,single phase with louvers. Make:-Havells/Usha/Crompton

S&F of pipes Galvanized steel water tubes medium grade, ISI marked galvanized with all fitings laid in trenches or roof/wall of sizes 25 mm dia complete all as specified and as directed by Engr-in-Charge

Cutting of existing 50 mm dia pipe GI/CI in position for insertion of new tees, tail pieces, flanged etc. including necessary jointing material for flanged fitting or lead joint complete all as specified and as directed by Engr-in-Charge

S&F Gate valve with iron wheel head(ISI marked) screwed both ends for iron pipe and fixed of dia 25 mm complete for the following sizes of GI pipes complete all as specified and as directed by Engr-in-Charge

Construction of brick masonary valve pit chamber of following size 450X450X450 mm (internal diemnsion) including PCC, brickwork and MS sheet cover 3mm thick, MS angel iron frame size 40 mmX 40 mm X 6mm around of valve pit,locking arrangement with pad lock size 25mm dia brass,6 lever with duplicate keys(make godrej) and painting all steel surfaces with two coats of synthatic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-Charge

M/S ANAND MOHAN ENTERPRISES

Bikarma Enterprise