PROVN OF GUARD REST ROOM AT RV AREA AND PROVN OF GALVALUME SHEET SHED ALONGWITH STRUCTURAL STEEL IN TECHNICAL AREA AT AF STN PALAM UNDER GE (AF) PALAM, DELHI CANTT - 10

M&L for surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soils complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth for foundation, etc. and getting out in any type of soil complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

Use and waste of form work (fair finished) to flat sides of concrete foundations, footings, bases of columns, raft and raft beams, side and soffits of foundations and plinth beams and similar works vertical or to batter and fair finished complete in all as specified and as directed.

Use and waste of form work to fair finished concrete flat surfaces of sides and soffit of floor or roof beams, beam, haunchings, girders, bressummers, lintels, cantilevers, shelves inclduing supports, over hangs etc complete in all as specified and as directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete wall, floor and roof n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20cm wide complete all as specified and as directed.

Use and waste of form work to fair finished concrete flat surfaces of sides of pillars, posts, columns etc complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and as directed.

M&L for RCC M-25 design mix using 20mm graded stone aggregate as in raft, foundation, beam, plinth beam, footing etc complete all as specified and as directed.

M&L for RCC M-25 design mix using 20mm graded stone aggregate as in column, struts, pillars etc complete all as specified and as directed.

M&L for RCC M-25 design mix using 20mm graded stone aggregate as in roof beam, lintel band etc complete all as specified and as directed.

M&L for RCC M-25 design mix using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, chajjas, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over as in reinforcement cut to length, bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Description all as srl item No. 13.00 above but 5mm dia and over upto and including 10 mm dia as in stirrups and binders etc complete all as specified and as directed.

Returning/filling in trenches in layer n exc 15cm thick including watering and well ramming complete all as specified and as directed.

Removing excavated material to a distance from site exc 500m but n. Exc. 1.5Km complete all as specified and as directed.

M&L for applying evenly a coat of hot blown bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified and as directed.

M&L for polythene film, 50 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan in any radius in half brick thick wall built in CM (1:4) complete all as specified and as directed.

M&L for 10mm thick rendering of ready mix plaster of approved make on brick/ concrete surfaces on internal walls, surfaces even and fair as per manufacturer's instructions, including necessary scaffolding complete all as specified and as specified.

M&L for 15mm thick rendering of ready mix plaster of approved make on brick/ concrete surfaces on external walls, fascia, parapet and chajjas, finished the surfaces even and fair including water proofing compound by weight as per manufacturer's instructions, including necessary scaffolding up to (G+3) storey complete all as specified and as directed.

M&L for 5 mm thick rendering of Ready mix plaster of approved make on brick/ concrete surfaces on ceiling, surfaces even and fair as per manufacturer's instructions, including necessary scaffolding complete all as specified

M&L for preparation of plastered or unplastered new surfaces of ceiling and applying three coat of white wash complete all as specified and as directed.

M&L for preparing new plastered surfaces and applying two coats of distemper oil emulsion on wall surfaces including primer over 3mm thick cement based wall care putty complete all as specified and as directed.

M&L for providing two coats of cement base paint over a coat fo primer after preparation of new plastered surfaces as on wall complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay, complete with glazing bars, dovetailed or welded & including cutting holes in brick walls for inserting holdfasts and making good dismantalled portion in CM (1:3) or cement concrete (1:2:4) type B1 complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay, complete without glazing bars, dovetailed or welded & including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B1 as required complete all as specified and as directed.

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and as directed.

S&F solid PVC door frame of size (50mm x 47mm) made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stliles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawing complete all as specified and as directed.

M&L for pressed steel frame for door with double rebated of size (125 x 60)mm including necessary fixing lugs, hinges, lock strike, plate etc with and including filling hollow portion with PCC (1:2:4) type B0 complete all as specified and as directed.

S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood factory made glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, provided with stiles and rails as specified in SSR Part-I Section-8 clause 8.24 (a) fixed to chowkats complete all as specified and as directed.

M&L for preparation of new undecorated painted wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and and average width of aperture not more than 1.40mm fixed with stainless steel wire staples complete all as specified and as directed.

S&F butt hinges 75mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolts of extruded section and fixed 150mm size complete all as specified and as directed.

S&F cast type anodised aluminium handles of size 150mm complete all as specified and as directed.

S&F curtain rail mild steel chromium plated with fixing brackets, stops, etc complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete all as specified and as directed.

M&L for 100mm thick PCC (1:4:8) type D2 (using 40mm graded granite stone aggregate) as in sub base including use and waste of necessary form work complete all as specified and as directed.

M&L for 60mm thick machine pressed precast concrete interlocking paver block of M-35 with glossy finish of approved shape and colour with and including 50mm thick sand filling, watering and consolidation complete all as specified and as directed.

M&L for machine cut Kota stone slab 20 to 25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete as in kitchen floor over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for machine cut Kota stone slab 20 to 25mm thick as in steps, skirting, dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick rendering in CM (1:4) complete all as specified and as directed.

M&L for hardcore gauge n. exc 63mm of broken stone or boulders deposited, spread and levelled in layers n. exc 75mm thick, watered and well rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, with and including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with and including bitumen 85/25 and sand in the proportion of (1:3 ) by weight complete all as spcified and as directed.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in floor etc complete all as specified and as directed.

M&L for glazed ceramic coloured tiles as in vertical surface of size (450 x 350)mm x 7mm thick / (350 x 250)mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match with and including over 10mm thick back coat in CM (1:4) such as skirting, dados, etc complete all as specified and as directed.

M&L for non- skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

S&F tubes, 'medium grade' 15mm bore galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F tubes, 'medium grade' 20mm bore galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) and cutting chases for concealed water tubing cutting not exc 10cm girth in brick wall complete all as specified and as directed.

S&F vitreous china wash down water closet pan (pedestal pattern) white including plastic water closet seat cover, white, closed pattern with flat bottom, and mild steel chromium plated hinging device and including "P" or "S" trap (exclusive flushing cistern and flush pipe) complete all as specified and as directed.

S&F health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and as directed.

S&F PVC valveless, syphonic action type, flushing cistern,10 ltr capacity low level, white, with inlet, ball valve, float and handle including brackets & flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and as directed.

S&F 15 mm bore chromium plated bib taps, with crutch or butterfly handle, fancy type, long body screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F 15mm bore dia CP finish, angle valve, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/CPVC pipe/fittings or for brass ferrule including cup washer/flange complete all as specified and as directed.

S&F wash hand basins, vitreous china of size (550 x 400)mm (flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and bedded in red lead cement, PVC waste pipe including 15mm bore dia CP cast copper alloy fancy type pillar tap, screwed for iron / CPVC pipe / fittings complete all as specified and as directed.

S&F vitreous china urinals, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe

S&F tubular towel rail, brass chromium plated 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F toilet paper holder with flat recessed type stainless steel complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 110mm PVC (SWR) WC connector bent type complete all as specified and as directed.

S&F PVC (SWR) junction single (single 'T') equal or unequal 110mm bore complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75 mm bore complete in all respect as specified and directed.

S&F PVC (SWR) 75mm dia bend type complete all as specified and directed.

S&F PVC (SWR) 100mm dia bend type complete all as specified and directed.

S&F cast iron nahani trap with CP grating including jointing with cement joint to waste pipe of 75mm dia fixed in cement concrete type B-1(1:2:4) complete all as specified and as directed by Engr-in-Charge.

S&F rotational moulded polythene water storage tanks of 1000 litres capacity three layered white colour including cover, anti mosquito cap, washout GI pipe, overflow GI pipe etc complete all as specified and as directed.

S&F ball valves 20mm high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed. (Minimum weight 20mm - 210 gms)

S&F gun metal, globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

M&L for 110mm bore PVC (SWR) pipe, single socket in any length with rubber ring joints fixed to wall including clamps complete all as specified and as directed.

S&F framed work such as grill, grating, etc with end of bars shouldered and / or revited, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, frame work of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for 15mm thick rendering on concrete surface on roof in cement plaster (1:4) finished even and fair without using extra cement by using Dr. fixit @ 3% of wt of cement content complete all as specified and as directed. Note:- Water proofing Compound shall be measured and paid seprately.

M&L for APP based modified pre fabricated five layer 3 mm thick and weighing not less than 3.6 Kg/Sqm water proofing membrane reinforced with polyester non woven fabric mat with 150 gm/Sqm black finished with compatible primer conforming to IS 3488 @ 0.30 Lit/ Sqm and bonding material 85/25 bitumen 1.2 Kg/Sqm before and after laying membrane laid by torch application side overlap of 75 mm and overlap of 100 mm longtitudinally, at the junction of roof and parapet wall a grove of 75mm wide and 65mm deep and shaping horizontal of groove with CM (1:3) with bituminous mastic joints/overlap shall be sealed with hot bitumen 85/25 complete all as specified and as directed.

Supply only integral water proofing compound complete complete all as specified and as directed.

M&L for 'E' board ceiling 4mm thick with GI framed work with main tee of size (24 x 28.5)mm made out of PGI sheet 0.3mm thick doubled at web and single at flange. Flanage covered with powder coated sheet 0.35mm thick and wail angles (24 x 24 x 0.3)mm powder coated for ceiling, ceiling board (60cm x 60cm) x 4mm thick, suspended with GI wire 2.24 mm dia and length as required @ 600mm C/C with adjustable device complete including plugging in brick/concrete work with steel raw plug @ 600 mm C/C and applying two coats of OBD over ceiling board. Ceiling board shall be pressed to the ceiling tee with staple clips at all four sides including making good all the disturbed portion complete all as specified and directed.

Supplying and laying 150mm bore Reinforced Cement Concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and as directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as concrete bed to drain pipes of 150mm bore including packing under and haunching against the sides of pipes, after they are laid and tested complete all as specified and as directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation and bed concrete or in channel and drain etc complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan, exc 6M mean radius, built in CM (1:4) complete all as specified and as directed.

M&L for rendering 15mm thick in CM (1:4) on brick/ concrete surfaces of walls finished even and fair complete all as specified and as directed.

Supply and fixing SFRC manhole cover of size (1000mm x 600mm) x 70mm thick laid over existing drain complete all as specified and as directed. Make:- (a) PS Concrete (b) M/s KK Manhole.(c) Or equivalent as approved by GE

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in kerbs or mud stops, rounded or chamfered edges, etc complete all as specified and as directed.

Excavation in post holes each n. exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n. exc 25cm, watering and well ramming earth or broken rubble mixed with around in layers n. exc watering and removing surplus soil to a distance n. exc 50m and making good surface in hard/ dense soil complete all as specified and as directed.

Excavation in post holes each n. exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n. exc 25cm, watering and well ramming earth or broken rubble mixed with around in layers n. exc watering and removing surplus soil to a distance n. exc 50m and making good surface in hard rock/ PQC complete all as specified and as directed.

S&F mild steel rolled section as in main and cross beams, hip and jack rafter, purlins where connected to common rafters and running rails and guides, fixed with angle cleats or other connecting plates etc conforming to Fe-410W (Gde E-250) quality-A grade complete all as specified and as direted.

S&F mild steel work in tubular trusses/ posts including special shaped washer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 complete all as specified and as direted.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of FE-410-W (Gde-E-250) quality B complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall or in ridge, valley gutters etc fixed with self tapping screws complete all as specified and as directed.

S&F flat iron fillets as in wind ties for roof including securing bolts/screw etc complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in coping and other similar band or holdfast block and necessary use and waste of form work complete all as specified and as directed.

M&L for broken stone or boulders hardcore of gauge n.exc. 63mm deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface for plinth protection/path complete all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) surface finished even and smooth without using extra cement complete all as specified and as directed.

Description all as per ser item No. 101.00 above but for one socket outlet 3pin 5 Amp controlled by one switch on independent board complete all as specified and as directed.

Description all as per ser item No. 101.00 above but for one 3 pin 5Amps socket out let point on the same board controlled by one switch complete all as specified and as directed.

Description all as per ser item No 101.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 sqmm stranded copper conductor cable PVC insulated including earth wire 2.5 sqmm copper conductor cable connected to earth dolly complete all as specified and as directed.

Description all as per ser item No 101.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 4 sqmm stranded copper conductor cable PVC insulated including earth wire 4 sqmm copper conductor cable connected to earth dolly complete all as specified and as directed.

S&F modular switch colourful white/black/golden etc 1 way 6 Amps one module complete all as specified and as directed by Engr-in-Charge.

S&F modular socket 6 Amps 2/3 pin combined 2 module complete all as specified and as directed by Engr-in-Charge.

S&F modular switch one way 16 Amps one module complete all as specified and as directed by Engr-in-Charge.

S&F socket modular type 6 amp/16 amps, 2/3 pin combined 2 module complete all as specified and as directed by Engr-in-Charge.

S&F ceiling rose, surface type, 65mm x 50mm, 3 terminals complete all as specified and as directed by Engr-in-Charge.

S&F stepped type modular fan regulator 100 watt 1 module, 230 volts, 50 Hz, AC supply complete all as specified and as directed by Engr-in-Charge.

S&F MCB protected socket PVC plastic base model (White), 4 module, 20 Amp suitable for AC box alongwith 3 pin top complete all as specified and directed by Engr-in-Charge.

S&F LED sleeky bldg security light (Lens) fitting of 35 watts, 6000K, including GI bracket bend to shape made out of GI pipe light grade of 25mm bore size upto 1.2 mtr long etc complete with two nos of clamps, nuts, bolts of suitable size, duly painted with two coats of synthetic enamel paint over a coat of primer and all fixing arrangements to wall/ pole, including connecting up with 2 core copper flexible wire of size 23/00.0076 complete all as specified and as directed.

S&F indoor decorative LED battens integrated type 20 watt 4 feet white/warm white fixture complete with all accessories internally prewired and including connecting up with twin core copper conductor cable complete all as specified and as directed by Engr-in-Charge.

S&F batten holder insulated body suitable LED lamp 10W, 220-240 volts, 6500 K, B-22 base cap complete all as specified and as directed.

S&F LED bulb of 9 watt, B22 base, 6500K complete all as specified and as directed.

S&F LED tube/mirror light fitting 9 watts, 2 feet batten type fixed on wall/ ceiling etc. including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

M&L for earthing complete with galvanized steel plate elecrode of size 60cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.25 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. Provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC (1:3:6) type C-2 using 40 mm graded stone aggregate shall be provided. The chamber shall be constructed one metre away from edge of earth pit of 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron of size (50 x 50 x 6)mm frame including two coats of synthetic enamel painting over a red oxide primer to exposed steel surfaces. Excavation in soft/ loose soil, returning, filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No. 3 of SSR Part-1 (2009).

S&F vertical type load line distribution board, double door, TPN 4 way, IP 43 IK09 AC, 3 phase, 415 volts, TPN bus bar 200 Amps rating and earth bar & din rail with IP 43 rating complete all as specified and as directed by Engr-in-Charge.

S&F sheet metal enclosure for distribution board SPN (when MCBs to be used ) 8 way double door, 200 Amps rated bus bars and with neutral, earthing bar and din rail with IP 43 rating complete all as specified and as directed by Engr-in-Charge.

S&F MCCB, 4 pole 200 Amp, 36 kA, 415 Volts complete with connections complete all as specified and as directed by Engr-in-Charge.

S&F MCB SPN 32 Amp, 10 kA, 230 V 'C' series complete with connections complete all as specified and directed by Engr-in-Charge.

S&F MCB SP 6-32 Amp, 10kA, 230 V 'C' series complete with connections complete all as specified and as directed by Engr-in-Charge.

S&F sub main wiring with two single core of 6 sqmm FRLS PVC insulated and unsheathed stranded copper conductor alongwith earth wire 6 sqmm drawn in 25 mm PVC rigid conduit connected to main board complete all as specified and as directed. Note:- Two core cable, one core earth wire and PVC conduit shall measured together as unit length.

S&F mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles/ walls, laid under floor/ road crossings, complete with and including necessary clamps, socket & elbow etc complete all as specified and as directed.

S&F PVC ventilation fan, with louvers shutter of sweep size 200/250mm, single phase, embedded in the wall / window including provision of PVC flexible copper cable from ceiling rose to fan giving connection along with mosquito jali on Wall/Window complete all as specified and as directed.

Supply and fixing BLDC ceiling fans five star rated complete with blades, down rods, electronic regulator, remote and all accessories, 230 V, 1200 mm sweep, Air delivery 225 CMM, RPM 350, Power 32W with service value 6.00 BEE with brushless direct current motor (BLDC) complete all as specified and as directed.

S&F LED flood light fitting 100-120 watt with internally prewired including electronic driver and connecting up with three core flexible copper conductor 1.5 sqmm cable complete all as specified and as directed.

Supply and fixing electric water heater (geyser), storage type with inner tank with glass lined coating and heating element heavy duty 2 KW capacity 25 litre, BEE 5 Star rated Engineered for hard water complete with all accessories such as pressure safety relief valve, thermostat, NRV, connection piece (steel armoured - 02 Nos) etc conforming to relevant latest IS including anchor fasterner - 04 Nos complete all as specified and as directed. Make:- Bajaj Shield Series Immorto, Crompton Amica Pro 25-L, Havells Greta Pro 25L or equivalent as per list of makes.

Supply and fixing stop valve, cast copper alloy fancy type, chromium plated screwed down, high pressure with crutch or butterfiy handle screwed both side for iron pipe 15 mm bore complete all as specified and as directed.

Supply, laying, jointing and testing of 50 Sqmm 3.5 core XLPE insulated, screened, PVC bedded, galvanized steel wire or strip armoured electric power cable (heavy duty) with aluminium stranded conductor 1100 volts grade, laid in trenches, passing through ducts/pipes, fixing along poles, complete all as specified and as directed. Note:- Excavation, earth work and protection of cable shall be measured and paid seperately.

S&F HDPE DWC electrical conduit, 100 mm nominal bore for passing of cable, fixed to poles/ walls, laid under floor/ road crossings, complete with and including necessary clamps, socket & elbow etc complete all as specified and as directed.

S&F air circulator wall mounted fans 230 volts single phase oscillating of size 400 mm sweep, 60 Watt Hi speed fan, plastic body & blades, pull cords for speed regulation & oscillation, mounting with bolts, nuts and including provision of PVC flexible copper conductor cable of size 23/0.0076 three core from ceiling rose to air circulator fan complete all as specified and as direted.

Supply and installing hi wall split units indoor and outdoor of split type AC of 2 TR complete with cordless remote control unit and with in-built air ioniser and plasma filter for better indoor air quality with BEE 5 star rating inverter type with and including suitable AC stand wall mounted / floor mounted type complete all as specified and as directed by Engineer-in-charge. Make:- Voltas/ Llyod / LG / Blue Star / Samsung / Godrej / Haier.

Supply and fixing voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanised iron steel tubing medium grade of size 25mm complete including cutting of existing pipe line for jointing with all fittings such as bend, tee, reducer, elbow and union of require size including fastners, bolts, washers, fixed on wall and making good to the disturbed surface after making hole complete all as specified and as directed.

Supply and fixing galvanised iron steel tubing medium grade of size 20mm complete including cutting of existing pipe line for jointing with all fittings such as bend, tee, reducer, elbow and union of require size including fastners, bolts, washers, fixed on wall and making good to the disturbed surface after making hole complete all as specified and as directed.

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) for iron pipe 20/25 mm bore complete all as specified and as directed.

M&L for screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) for iron pipe 20/25 mm bore complete all as specified and as directed.

Supply and fixing stop valve, cast copper alloy fancy type, chromium plated screwed down, high pressure with crutch or butterfiy handle screwed both side for iron pipe 25 mm bore complete all as specified and as directed.

Supply and fixing stop valve, cast copper alloy fancy type, chromium plated screwed down, high pressure with crutch or butterfiy handle screwed both side for iron pipe 20 mm bore complete all as specified and as directed.

Please Enable Macros to View BoQ information