Renovation Work At Old Block

Amount

Exterior Berger Anti Dustt Paint with antidust Properties and dirt pickup resistance. Surface Prepartion :-Sanding with dry wall sander and building wash with High Pressure jet washer. 1 Coat Primer ( primer with triple booster formulation that fights against dampness, efflorescence and alkalinity )+ Repair with crack filler and HS latex plus + 2 more coat of Ext Emulsion Anti dustt paint all complete .

Distempering with oil bound washable distemper of approved brand and manufacture (Berger/Asian paint) to give an even shade : Two or more coats over and including water thinnable priming coat with cement primer. New and old Work

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Dismantling doors, windows and clerestory windows shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Fixing chowkhat in existing opening in brick/ RCC wall with dash fasteners/Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and all fittings wherever required including the cost of EPDM rubber / neoprene gasket required. Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) 88Sqm @9.5kg/sqm

Providing and fixing 6 mm thk tinted toughened glass in aluminium door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) :

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Weathercoat PU Roof Coat Berger Make :- Water based LiquidMembrane One component liquid, solvent free, cold applied waterproofing membrane, compliance with ASTM D 6083-97a. Surface Preparation:- 1) Clean the surface by removing Dust/Slurry and all creepers first with Wire brush then air blower and with Clean water. Ensure removal of algae or fungi from the surface. Surface must be free from dust, dirt, loose portions, oil, grease, efflorescence, old coatings etc. cleaning shall be done thoroughly. 2) In case any cracks which is less than 5mm use home shield crack fill paste and in case of crack more than 5mm treat with polymer modified mortar (Cutting V groove and pouring cement mortar mixed with Advance Latex Plus). 3) Apply 2 Coats of latex shield 2K (with the 6 Hrs Gap between each coat). Application of HS PU RoofKoat: Polyurethane based elastomeric waterproofing coating. a) Application of 1st coat of HS PU Roof Koat 50% water dilution prime coat over prepared surface. b) Application of 2nd coat of HS PU Roof Koat (without dilution) over primed surface (once primer become dry, preferably after 2-3hrs).c) Application of 20 gsm geotextile fleece over 2nd coat on wet condition so that it sticks properly. Overlapping of 50 mm to bemaintained. d) Application of 3rd coat of PU Roof Koat (without dilution) over geo textile fleeced surface (coat interval 6 hours) and allow the coating to be fully cured.

SHREE KRISHNA CONSTRUCTION CO.

Naagar Infrastructure Pvt Ltd

CREATORS ENGINEERS & INTERIORS

HANUMAT INFRATECH PRIVATE LIMITED