ADDITION/ALTERATION AND SPECIAL REPAIRS TO EXISTING OTM ACCN AT GRC KAMPTEE

Amount

Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department.

Demolition of plain cement concrete in ground floor & paving not exc 15 cm thick above or below ground level complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Removing excavated material (soil) n .exc 50m and deposited where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including ashlar facing dressed stone and pre-cast concrete articles complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls/chajja/pillars, etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

Supply & fixing roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410 w (Gde E-250) quality 'A' complete all as specified and directed.

Dismantling Plain, CGI Sheet corrugated of any gauge thickness including pattern roof coverings complete all as specified and directed.

Dismantling of asbestos cement/translucent sheet corrugated/ semi-corrugated sheets in roof coverings including ridges complete all as specified and directed.

Dismantling of wall and ceiling board (fibre, insulation etc) or insulation board, slabs, blankets, any thickness including cover fillets complete all as specified and directed.

M&L for suspended false ceiling system using snap grid, non asbestos fibre ceiling board of size 595mm x 595mm x 4mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel section @ 90 grams/sqm (both side inclusive) consisting main 'T' runner with suitably spaced joints to get required length and of size 24mm x 38mm made from 0.25mm thick (minimum) sheet, spaced at 1200mm centre to centre and cross 'T' of size 24mm x 25mm x 1200mm made of 0.25mm thick (minimum) sheet, 1200mm long spaced between main 'T' at 600mm centre to centre from a grid of 1200 x 600mm and secondary cross 'T' length 600mm and size 24mm x 25mm x 600mm made of 0.25mm thick (minimum) sheet to be interlocked at middle of the 1200mm x 600mm panel from grids of 600mm x 600mm and wall angle of size 24mm x 24mm x 0.4mm including required cutting/making, opening for services like diffusers, grills light fitting, fixtures, smoke detectors, etc., main 'T' runners to be suspended from ceiling using slotted cleats of size 27mm x 37mm x 25mm of 1.0mm thick fixed to ceiling with 4mm GI bar hangers adjustable with galvanised butterfly level clips of size 85mm x 30mm x 0.5mm spaced at 1200mm centre to centre along main 'T', bottom exposed width of 24mm of all 'T' sections, all shall be pre-painted with polyster paint, for all heights as per specification complete all as per manufacturer instructions and complete all as specified and directed.

S&F non asbestos fibre cement false ceiling boards (595mm x 595mm x 4mm) (Texture) fixed with anodised aluminium snap grid frame work all as specified etc all complete fixed to timber/GI/Aluminium framework in ceiling with screw etc complete all as specified and directed.

M&L for taking down and refixing of false ceiling board in existing frame work of any description / position after cleaning/painting and repair of existing snap grid frame work complete all as specified and directed.

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any type, colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in weather boarding/eaves board in approved design/ pattern/shape to match with existing adjacent water boarding/eaves boards inclusive, as in ridges, hips, valley gutters, drip and straight and fixed with self tapping screw/nut bolt/normal GI screw/nail et as per site requirement at any height/position complete all as specified and directed.

Taking down existing water proofing treatment including PCC padding, mortar, etc and disposal rubbish out side MD land and hacking for key scrubbing down with water complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 (using 12.50 mm graded stone aggregate) as in padding over RCC roof complete all as specified and directed.

M&L for water proofing treatment by using APP torch on mineral/slate finished membranes over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing APP membrane having non woven polyester film reinforcement with 3 mm thick and weight not less than 3.00 kg/sqm and finished on top with mineral/slate finished torch on system; laid with 100 mm & 150 mm over lap on side & end laps respectively and applying two coats of aluminium paint as per manufacturers instructions complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:4 on brick or concrete surfaces using water proofing liquid compound and finishing surfaces even & fair without using extra cement. complete all as specified and directed. Note: water proofing liquid will be measured and paid separately.

Taking down door/window frames incuding shutters (without taking of shutter from the frames) n.exc 1.50 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down door/ window frames including shutters (without taking of shutter from the frames) exc 1.50 Sqm and not exc 4 sqm complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm but n. exc. 2.00 Sqm complete all as specified and directed.

S&F steel window with side hung shutters (glaze & gauze shutter) including projecting or box type hinges with steel handle peg stay and divided into square with glazing bars dovetailed or welded, to receive glazing, or gauzing including one coat of primer including fixing of hold fast of size 25 x 5 mm flat iron, etc complete all as specified and directed.

All as per BOQ Serial Item No.24 above but with glazing/sash bars for fly proofing complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges peg stay to receive glazing or gauzing and one coat of primer including fixing of hold fast size 25 x 5 mm of flat iron, etc complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 (using old size brick) complete all as specified and directed.

M&L for brick work with fly ash brick, straight or curved on plan to any radius built in half brick thick wall built in cm 1:4 (using old size brick) complete all as specified and directed.

M&L for rendering 15 mm thick in two coats (10 and 5mm thick) in CM 1:4 on brick or concrete surfaces even & fair smooth, using water proofing liquid compound and without using extra cement complete all as specified and directed. Note: water proofing liquid will be measured and paid separately.

M&L for rendering 10 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed..

M&L for rendering 5mm thick CM 1:3 on brick or concrete surfaces of ceiling /chajja's finished even & smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, but not backing removing serviceable tiles to store and rubbish off the premises up to 1 KM complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed or bedding layer in CM 1:4 finished fair and even for laying floor finishes/tiles etc complete all as specified and directed.

M&L for 10mm thick joint free vitrified tiles (Square/rectangular ) polished, area of each tiles not exc 0.36 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including screed bed or bedding/rendering layer 15mm thick in mortar CM 1:4 finished even and smooth for laying floor finishes complete all as specified and directed.

All as per BOQ Serial Item No.34 above but in skirting/dado including rendering 10mm thick in CM 1:3 as backing coat to receive tiles complete all as specified and directed.

M&L coloured glazed ceramic wall tiles 300 x 450 x 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles with & including rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 as backing coat to receive wall tiles/skirting/dados complete all as specified and directed .

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25mm thick (size not less than 450mm x 600mm) with and including 20mm thick cement screed base in CM 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar, etc with and including 10mm thick rendering in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed.

M&L for grinding & mirror polishing on existing old kota stone surfaces including filling all existing joints with grey cement slurry mixed with pigment to match the shade of slab complete all as specified and directed..

M&L for Cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in 25mm thick sub floors, leveling course, etc finished even & rough complete all as specified and directed.

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

Dismantling of cast iron pipe of 100 mm dia jointed in cement mortar and taking out from trenches, if required complete all as specified and directed.

Dismantling of cast iron pipe of 150 mm dia jointed in cement mortar and taking out from trenches, if required complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, etc including cleaning or refixing or removal to store complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F stack clamp made out of 50x5 mm flat iron for 75 mm dia of pipe complete all as specified and directed.

S&F stack clamp made out of 50x5 mm flat iron for 110 mm dia of pipe complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore, provided with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore, provided with access door complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (single Y) equal or unequal, 110mm bore, provided with access door, complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (single Y) equal or unequal, 75mm bore, provided with access door, complete all as specified and directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth complete all as specified and directed

S&F PVC (SWR) / rain water pipes 150 mm bore, single socketed in any length with rubber ring joints fixed to walls including taking down existing pipe of any description complete all as specified and directed.

S&F PVC (SWR) bends any radius, 150 mm bore, provided with access door complete all as specified and directed.

Taking up or down steel tubing and connections15mm bore complete all as specified and directed.

Taking up or down steel tubing and connections20mm bore complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F PVC (SWR) Nahani trap 75 mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan, pedestal pattern concealed, ISI marked, white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device complete all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 liters capacity dual flush, ISI marked, white, with all fitting and fixtures including brackets and fixing 32 mm bore PVC flush pipe, complete all as specified and directed.

Supply only flush pipe of polythene of low or high density 32 mm PVC for low level flushing cistern complete all as specified.

Supply only PVC connection 15 mm dia, 450 mm long including brass ferrules on both ends complete all as specified and directed

Supply only low density PVC pipe 32/40 mm dia as in waste pipe to sink/WHB complete all as specified and directed

S&F in repairs tubular towel rail of aluminium anodised, 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed.

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed.

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed.

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, ISI marked screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed

S&F in repairs Vitreous china wash basin, white, flat back, size 630 x 450mm counter sunk, oval type fixed in granite excluding taps, waste, chain and plug and porcelain stopper complete all as specified and directed.

M&L for pre- polished granite slab machine cut of any shade as approved by GE of 18 to 20 mm thick including necessary notching, chamfering the edges over cement screed bed including Cutting, Grinding and Mirror polishing (Granite finish) with suitable grinding stones complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platforms, and other similar situations complete all as specified and directed.

Dismantling water tank of capacity exc 250 ltr & not exc 500 ltrs and removing to store of any description complete all as specified and directed

Dismantling water tank of capacity exc 500 ltr & not exc 1000 ltrs and removing to store of any description complete all as specified and directed

Dismantling water tank of capacity exc 1000 ltr & not exc 2000 ltrs and removing to store of any description complete all as specified and directed

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 2000 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

M&L for preparation of new surfaces and applying two coats of exterior grade weather proof paint over a coat of primer, water based on wall surfaces complete all as specified and directed

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including M&L for applying two coats of exterior grade weather proof paint, water based on wall surfaces complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall & applying two coats of cement base paint complete all as specified and directed

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over and including applying 3mm thick wall care putty complete all as specified and directed

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including M&L for applying 3mm thick wall care putty and applying two coats of distemper, oil emulsion white or tinted over and including one coat of readymade cement primer complete all as specified and directed.

M L for preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceilings and applying two coats of white wash complete all as specified and directed

M&L for preparation of new plastered surfaces and applying three coats of white wash on Walls complete all as specified and directed

M&L for preparation of old plastered surfaces and applying two coats of white wash on Walls complete all as specified and directed

M&L for Preparation of old wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over coat of pink primer complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed

M&L for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10 mm dia as tie bar complete confirming to Fe-410 -W (Gde E-250) quality A complete all as specified and directed.

S&F Plain mild steel wire of 4mm dia, galvanised class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc complete all as specified and directed.

S&F mild steel screw bolts ( machine made) of dia 16mm to 20mm with hexagonal and square heads at one end and screwed at the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut; length of bolt exc 22.5cm and n.exc 30cm long complete all as specified and directed.

S&F 35 mm thick plain framed panelled factory made shutter made out of IInd class hard wood rail and styles and panel of 12 mm thick veneered particle board or 9 mm thick plywood with commercial veneering on both faces the size of rail and style as per IS 1083 (part-I) kiln seasoned an chemically pressure treated of any number of panel complete all as specified and directed.

S&F flush shutters solid core construction with block board core and plywood face panels commercial type on both sides 35 mm thickness complete all as specified and directed.

S&F 35 mm thick IInd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats or frame etc any numbers of panels complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood grain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded wood grain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of wood grain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for rough cast, wired glass, 6.4mm thick and glazing with oil putty in squares exc 0.5 but n exc 0.75 sqm complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised, 125 mm size complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section, 150mm long complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section, 75mm long complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F sheet glass ordinary quality, 3 mm thick and glazing with oil putty in square n. exc. 0.50 Sqm in each pane complete all as specified and directed

S&F 3 mm figured glass, pin head type and glazed with oil putty in sqm n exc 0.50 sqm in each pane complete all as specified and directed

S&F aluminium frame for doors, windows, ventilators (powder coated) of any colour (thickness or powder coating not less than 50 micron)) with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engr-in-Charge.

S&F aluminium door shutters aluminium (powder coated) of any colour (thickness or powder coating not less than 50 micron)) section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F aluminium windows and ventilator shutters (powder coated) of any colour (thickness or powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified.

S&F brass mortise lock (4 levers), vertical type, size 100mm long including all fitting arrangements complete all as specified and directed.

S&F Heavy duty Aluminium body floor door spring (ISI marked) suitable for Aluminium swing doors, double action type including necessary cutting in floors and making good to match with the existing surface complete all specified and directed.

S&F prelaminated particle board 12mm thick, exterior grade, pre-laminated both sides with decorative choice lamination, fixed with screws to timber/aluminium frame work complete all as specified and directed.

S&F sheet glass ordinary quality, 4.00 mm thick and glazing with oil putty in square n exc. 0.50 Sqm in each pane complete all as specified and directed

S&F for sheet glass 5.50 mm thick tinted quality and glazing exc 0.50 sqm in each pane complete all as specified and directed.

S&F Ball brass valves, ISI marked, high pressure, with polythene float and fly nut, screwed for iron pipe or brass ferrule 20mm bore complete all as specified and directed.

S&F Vitreous china urinal full stall, white, with & including chromium plated waste coupling including connections to flush pipe and outgoing pipes complete all as specified and directed.

S&F Plywood, grade BWR,type BB, fixed with screws to timber/MS frame work thickness 6 mm fixed to receive the lamination sheet complete all as specified and directed.

S&F Decorative laminates 0.90mm thick type I, or surface finish, colour and pattern as approved complete all as specified and directed.

M&L for Marble (makrana white) work (table rubbed and polished) for wall lining (veneering to wall), skirting/ dado/cill/lintels /floor/jams, etc. 25 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified and directed.

Supply only liquid integral water proofing chemicals complete all as specified and directed.

S&F wire netting of fibre mesh (grid size 2.5mm x 2.5mm and 120 GSM) fixed in properly with suitable nails or glue as per manufacturer instruction for repair of cracks at various locations in wall, beam, chajja, faces, slab, lintel, etc including taking down plaster of cracked portion and making good the area by rendering in CM 1:3 and finally to match the surface with adjacent surfaces by applying white wash or cement base paint as applicable complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in foundations, footing, plinth beams, bases for columns, basement/ grade slab, etc and mass concrete complete all as specified and directed..

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in columns, pillars, posts & struts complete all as specified and directed.

Use & waste of Form work to chullah hoods, chajjas, column/pillar troughs and similar items including edges for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for design Mix RCC M-25 using 20mm graded aggregate as in landings, balconies, canopies etc complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Mild steel TMT 6 to 8mm dia cut to lengths bent to shape required including cranking, bending spirally for hooking and binding with MS wire( annealed) not less than 0.9mm dia etc all as specified & directed.

M&L for expanded metal (wt n.exc 4kg per sqm), cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed.

M&L for Cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required to match the adjacent surface; cutting exceeding half brick but not exceeding one brick complete all as specified and directed.

S&F angle iron frame work for placing desert cooler /wind tie/partition frame work etc including anchor bolts (fasteners of 8mm dia and 100 mm long) and all necessary drilling, welding, bolting or riveting, etc. and similar work and fixing to the required location and position including shape and size conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub-base, under floors and pavings complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C1 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for Cement Concrete 1:2:4 type B1 using 20mm graded stone aggregate as in floors and paving, 100mm thick, laid in panels and finished even & smooth without using extra cement and metallic hardener complete all as specified and directed.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:4 complete all as specified and directed.

M&L for Chequered paver tiles reflective/glossy type, any colour as decided by GE, size- 300mm x 300mm x 20 to 25mm thick, set, jointed and pointed in neat cement slurry in floors, etc complete all as specified and directed.

S&F for 25mm dia curtain rod of approved quality including cutting and fixing to curtain brackets complete all as specified and directed.

S&F for fancy type curtain brackets of approved quality fixed to wall with screws complete all as specified and directed.

Demolition of reed lathing, single or double including battens and plaster or chicken wire lathing, RCC jali complete all as specified and directed.

M&L for providing precast reinforced cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in louvers and jallies 35mm thick (measured solid) of approved design/style including all mouldings and set in cement mortar 1:4 complete all as specified and directed.

S&F Automatic stainless steel air turbo ventilator (base dia 600mm and exhaust dia 810mm & minimum 38 blades) with unbreakable UV & temp resistant, minimum thermal expansion & contraction, fire retardant (self-extinguishing) polycarbonate sky light sheet, sheet shoes as per manufacturer’s instructions, ventilator should be rain and storm proof, self-lubricant, maintenance free, high grade material all as per sample kaept in GE's office complete all as specified and directed.

S&F Aluminium grills for windows (in approved design/pattern) fixed with aluminium beading complete all as specified and directed.

Taking down point wiring with aluminum conductor cable of light point fan & socket light & power complete including light fittings any type, switches, sockets, ceiling rose, switch boards, bell/buzzer, bell push, tube light fitting, regulator, etc, and making good the disturbed surfaces of walls/ floors, etc to match with existing surfaces including white washing/colour washing/ distemper to match with existing wall/floor/ceiling finishes complete all as specified and directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed.

Taking down sub main wiring of any size/ capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces complete all as specified and directed.

M&L point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in & including non metallic rigid PVC conduit (ISI marked) medium grade not less than 20mm diameter with all conduit accessories in concealed wiring system by cutting of brick/stone wall and making good disturbed surface of wall in CM 1:3 (except on ceiling for fan point only, surface casing capping will be used in lieu of concealed PVC conduit) including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm, pressed steel modular boxes sunk on wall for mounting of modular switches, switch sockets, fan regulator, etc including modular box and cover with frame any size complete all as specified and making good disturbed surfaces for one light point controlled by one, one way switch complete all as specified and directed. Note :- (i) Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. (ii) All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly

All as per BOQ Serial Item No.154.00 above but One ceiling /exhaust fan point controlled by one switch and regulator complete all as specified and directed.

All as per BOQ Serial Item No.154.00 above but One 3 pin 5 amp socket out point on the same board with other switches complete all as specified and directed.

All as per BOQ Serial Item No.154.00 above but One 3 pin 5 amps socket out let point on independent board complete all as specified and directed.

All as per BOQ Serial Item No.154.00 above but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point complete all as specified and directed.

All as per BOQ Serial Item No.154.00 above but wiring with 4.0 sqmm multi stranded cable and earth wire with copper conductor of size 4.0 sqmm for 15 amps power point.

All as per BOQ Serial Item No.154.00 above but One bell/buzzer point controlled by one bell push complete all as specified and directed.

M&L for sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLSH cable 1100V unsheathed with stranded copper conductor of 4.0 sqmm nominal cross section area and drawing into non metallic rigid conduit with & including PVC insulated stranded copper conductor of 4.0 sqmm nominal cross section area as earth wire complete all as specified and directed. Note: - (i) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor shall be measured as one unit length. (ii) Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same make.

All as per BOQ Serial Item No.161.00 above but 2 x 6.0 Sqmm with earth wire of 1 x 6.0 Sqmm complete all as specified and directed.

All as per BOQ Serial Item No.161.00 above but 2 x 10.0 Sqmm with earth wire of 1 x10.0 Sqmm complete all as specified and directed.

S&F ceiling rose surface type 2/3 terminal 5 amps complete all as specified and directed.

S&F lamp holder insulated body with back plate for angle/ batten fitting complete all as specified and directed.

S&F Modular switch one way 6A, 1 module complete all as specified and directed.

S&F Modular switch one way 16A, 1 module complete all as specified and directed.

S&F Modular Socket 6A 2/3 pin combined 2 module complete all as specified and directed.

S&F Modular Socket 6A/ 16A 2/3 pin combined 2 module complete all as specified and directed.

S&F Modular Fan step regulator,120 watt 2 module complete all as specified and directed.

S&F LED tube light wall/ceiling mounted, minimum capacity of 1 x 18 watts LED, box type tube light with system lumens with efficacy > 115 Lm/W at system level (including the driver loss). The luminaire should have cool day light colour temperature of 6500 K CRI > 80, Life 40,000 burning hours with 70% lumen maintenance, PF > 0.95, surge protection of > 2KV; all photometrical and electrical parameters must be supported by LM 79-80 test report from NABL accredited lab or UL switching cycle of 50,000 times, lamp starting time not more than 1 sec; the LED tube light must confirm to applicable IS 10322/EN 60598; housing of batten should be made from single piece poeder coated CRCA steel sheet complete all as specified and directed.

S&F light fitting 9W LED bulk head luminaries with lamp holders etc complete with all accessories and including connecting up with twin core twisted flexible cable suitable size of 230V, 50HZ complete all as specified and directed.

S&F Energy efficient surface mounted 2'X2' grid Ceiling LED fitting 36/40 W rated voltage 240 V, 50Hz combination with profiled and flat diffuse complete all as specified and directed.

S&F building security light LED 25 W with Lumen O/P 1800 with driver with rated voltage 240 V, 50Hz,including mounting GI (made out of 25 mm dia light grade pipe 0.8 m bent two shape including FI clamps nut bolts etc complete all as specified and directed.

S&F LED tube light wall/ceiling mounted, minimum capacity of 1 x 9 watts LED, box type tube light with system lumens with efficacy > 115 Lm/W at system level (including the driver loss). The luminaire should have cool day light colour temperature of 6500 K CRI > 80, Life 40,000 burning hours with 70% lumen maintenance, PF > 0.95, surge protection of > 2KV; all photometrical and electrical parameters must be supported by LM 79-80 test report from NABL accredited lab or UL switching cycle of 50,000 times, lamp starting time not more than 1 sec; the LED tube light must confirm to applicable IS 10322/EN 60598; housing of batten should be made from single piece poeder coated CRCA steel sheet complete all as specified and directed.

S&F sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting double door complete all as specified and directed.

S&F sheet metal enclosure vertical triple pole & neutral(VTPN) with MCCB 40 amps for 415 volts 4 way with 200 Amp rated bus bar flush /surface mounting double door complete all as specified and directed.

S&F MCB single pole 240 volt 6 to 40 amps 10 KA breaking capacity, 'C' series complete all as specified and directed.

S&F MCB single pole and neutral 240 volt 6 to40 amps 10 KA breaking capacity, 'C' series, complete all as specified and directed.

Earthing complete with galvanized street earth plate electrode 600x600x6mm thick buried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanized iron or steel all as shown in electrical plate No 5 connected to earthing test point complete all as specified and directed and testing on completion including the material and labour for following :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric weighting not less than 1.87 Kg/sqmm (d) Funnel with watering pipe of GI 20mm nominal bore medium grade and Aluminum lugs etc all as specified. (e) 15mm nominal bore medium grade GI protection pipe up to 7.50 meter long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

S&F Exhaust fan single phase,200/230 mm sweep, metalllic with bolts, nuts, washers and connected electrically complete all as specified and directed.

S&F Air Circulator fan 450mm sweep, 250V, 50 HZ complete with all fittings complete all as specified and directed.

S&F 3 phase trunking bus bar panel with 200 amp aluminium bus bar flush mounted complete connecting with existing supply complete all as specified and directed.

S&F Rigid non metallic 25 mm dia PVC conduit inclusive of boxes, Junction/terminal all tees, bend,elbow,reducers,bell mouth tube ends and fixing accessories such as couplers, lock nuts,saddles,pipes hook etc concealed on surface on wall and making good including taking down existing TV, Telephone, Signal cables and re used in given non metallic PVC conduit complete all as specified and directed.

S&F Rigid non metallic 32 mm dia PVC conduit inclusive of boxes ,Junction/terminal all tees, bend,elbow,reducers,bell mouth tube ends and fixing accessories such as couplers, lock nuts,saddles,pipes hook etc concealed on surface on wall and making good including taking down existing TV, Telephone, Signal cables and re used in given non metallic PVC conduit complete all as specified and directed.

S&F Rigid non metallic 40 mm dia PVC conduit inclusive of boxes ,Junction/terminal all tees, bend,elbow,reducers,bell mouth tube ends and fixing accessories such as couplers, lock nuts,saddles,pipes hook etc concealed on surface on wall and making good including taking down existing TV, Telephone, Signal cables and re used in given non metallic PVC conduit complete all as specified and directed.

Excavation in trenches for laying of cables, poles and stay in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.50 mtr deep and getting out complete all as specified and directed

Returning filling in,including spreading, leveling watering and well ramming in layers not exceeding 25 cms thick complete all as specified and directed

Removing excavated materials not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed

S&F Double wall Corrugated High Density Polymer Ethyl (HDEP) pipe for laying of Electric cable of size 50 mm outer diameter and 38 mm inner Diameter with IS 14930 (part 2) 2001 and 6 mm thickness laid in trenches,wall, floor , pole including bends, sockets and other connected accessories complete all as specified and directed.

Supply and laying in trenches or fixing in walls / poles or drawing through pipe XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 25 sq mm, 4 core including testing after laid and jointed complete all as specified and directed.

Deduct schedule of credit (calculation will be done off line) Rs.6,81,503.00

SIBAL AND SIBAL

M/s Dara Constructions, Pulgaon

Quality Builders

chronicle enterprises

M/s MM TRADERS

M/s JAYPEE ENTERPRISES

M/S JAI BHAWANI CONSTRUCTIONS

M/s Shrangi Rishi Construction

Manak landmarks