KKNPP CSR 2025 26 Establishment of Disaster Control and Coordination Center in Tirunelveli District

1) Establishment of Disaster Control and Coordination Center in Tirunelveli District.

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of walls Brick / stone masonry in Cement mortar walls under 3m hin

Dismantling, mosaic in sites finish cement morter floor clearing away and carefully stacking materials useful for re-use for any thickness of walls Floor finish and dadooing walls in cement mortar with mosaic tiles / glazed tiles / cuddapah slabs

Brick work in CM 1:5mix using country bricks ground moulded of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard nerificntjnn in First FloorJ

Supply and Fixing in position of Cuddapah slab of 25 mm thick non polished for hoor including pointing and all other labour charges etc., complete as per standard spcifications

Providing Cup-board Shutter with frame using termite /water proof plvv/ood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol alcng with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed’ by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer before use on work. P.No 48

Plastering with Cement Morter 1:5 mix 12 mm thick inculding cost and conveyance of all materials to site and labour charges for curing etc

Paving the floor with best quality vitrified Tiles of following size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplyins and painting the walls with two coats of wall put:ty as instruct:ed fry the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before

Grid Ceiling Providing and fixing in true horizontal level false ceiling grid of Prelude exposed 24 mm grid system with 15mm manufactured by Approved Make by Architect.Using hot dipped chemically cleaned capping prefinished in baked polyster galvanized steel section exposed surface paint wall angle of size 3000 x 19 x 19mm used in the periphery of the ceiling fixed to the wall partition RC column band walls with the help of screw at 600mm C/C. main runner of size 3000x15x32mm suspended at a 1200mm C/C by using 2mm/3mm dia GI wire hanger securely fixed to the structural soffit of RC slab by using 6mm anchor fastener at every 1200mm (max) and 1200mm long cross tee of size 15 x 32mm to be interlocked between in main runner at 600mm C/C. (max) to form a grid of 1200 x 600mm.long cross tee of size 15 x 32 fixed In between 1200 mm long cross tee Black silhouette for forming a grid of 600 x 600mm. Finally laying Armstrong Lay - in Fine fissured 99 Board edge Ceiling with Perforated (standard) tile of Trulok Edge manufactured by M/s Armstrong world Industries Ltd.,

Providing and fixing of Aluminium Composite Panel (ACF) 4 si‹Jecl having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is — 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4n1m thick ACP sheet (0.25 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACI’ sheet bounded with special type structui al sealant of do lv corning 789 or quivalent in dust free conditions the gaps between ACF sheet to be filed faith whether sealant: and backer rod or 12mm foam sheet to ensure wateF 5I!1d air tightness in all complete complying with standard specification as directed by the departmental officer (M-0658)

He supply and installation of uPVC partitions with doors shall utilize uPVC profile sections with an outer wall thickness of 2.30mm (±0.2mm), featuring an outer frame of 74mm x 60mm x 56mm, a shutter of 104mm x 60mm x 66mm, a mullion of 72mm x 60mm x 36mm, a glazing bead of 35mm x 18mm, a 20mm multi-chambered hollow uPVC panel section of 150mm x 20mm, and a uPVC panel bead of 19mm x 16mm. All profiles of frames, sash, and mullion shall be reinforced, where required, with 1mm thick GI steel sections. The door will be equipped with 3D hinges for enhanced weight holding capacity, and security devices such as multipoint lock systems with a cylinder lock facilitated handle, all compliant with relevant specifications and departmental directives. Glazing or uPVC panels shall be 5mm thick Plain Toughened or uPVC panel grip, held by TPE (Grey) weather-sealed gaskets. All corners and mullion joints of the frame and sash shall be mitred cut and fusion welded without mechanical joints, with all welded joints neatly trimmed to a grooved nib finish, ensuring the finished products are free from sharp edges. The complete units shall be fixed into pre-finished openings by drilling and fastening through the outer frame using high-quality fasteners, and silicon sealant shall be applied to fill the gap between the wall and the frame for a leakproof installation and completion etc., Complete. and as directed by the department officers. Collapsible UPVC Glazed Partition including the cost of Materials, Transportation, Tools & Fittings and labour charges for fixing in position (M-3005)

Earth work excavation and depositing on bank with in initial lead of 10 m and initial lift of 2m in hard stiff clay, stiff black cotton soil, hard red earth,earth mixed with small sized boulders and hard gravelly soil as per SS 20B

Filling the basement with excavated earth in layer not more than 15 Cm. complying the Standard specification

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing,laying and curing etc complete

Brick work in cement mortar 1:5 mix using country bricks 83/4"x4 1/4"x2 3/4" and conveyance of all materials to site and all labour charges etc complete

Plastering with Cement Morter 1:5 mix 12 mm thick inculding cost and conveyance of all materials to site and labour charges for curing etc complete

Paving the floor with best quality vitrified Tiles of following size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the Floor with scratch proof Designed colour ceromic tiles of size 305x305x6mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing of walls with Printed design glazed tiles of size 30 cm x20cmx6mm laid in CM 1:2, (One Cement and Two crushed stone M.Sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Distembering two coats with best approved distember including cost and conveyance of all materials to site and all labour charges etc complete

Fabrication and supply of Mild Steel glazed Window of any size with single leaf outer frame,mullion section made of 35x35x5 mm equal M.S angle and shutter frame made of 25x25x5 mm M.S angle for horizontal and vertical member with stiffener etc complete

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Fabrication and supply of Mild Steel Ventilators of any size with single leaf outer frame made of 35x35x5 mm equal M.S angle and shutter frame made of 25x25x5 mm M.S angle for horizontal and vertical member with stiffener and fully covered with 18 G plate etc complete

Painting Two Coats for new iron work such as doors windows and ventilators etc complete

Exterior Emulsion painting two coats with best approved quality and colour paint over one coat of Base coat including cost and convyance of all materials to work site and labour charges etc., complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Providing and fixing in true horizontal level false ceiling grid of Prelude exposed 24 mm grid system with 15mm manufactured by Approved Make by Architect.Using hot dipped chemically cleaned capping prefinished in baked polyster galvanized steel section exposed surface paint wall angle of size 3000 x 19 x 19mm used in the periphery of the ceiling fixed to thë wall partition RC column band walls with the help of screw at 600mm C/C. main runner of size 3000x15x32mm suspended at a t200mm C/C by using 2mm/3mm dia GI wire hanger securely fixed to the structural soffit of RC slab by using 6mm anchor fastener at every 1200mm (max) and 1200mm Icng class tee of size 15 x 32mm to be intei locked between in main runner at 600mm C/C. (max) to form a grid of 1200 x 600mm.long cross tee of size 15 x 32 rxed In between 1200 n m long cross tee Black silhouette for Vorming a grid of 600 x 600mm. Finally laying Armstrong Lay - in Fine fissured 99 Board edse Ceiling with

i) Electrical Arrangements

Wiring with 2*1.5 mm (22/0.3) PVC insulated unsheated Sc Cu conductor of 1100 V Grade in suitable PVC ridged pipe on wall and ceiling with PVC accessories with tw switch box inflush with wall covered hylum sheet of 3 mm thick with painting of suitable colour for open PVC light point and fan point SD 18

Wiring with 2 x 1.5 sqmm PVC unsheated Sc alu cable of 1100 V Grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113 mm T.W Switch box in flush with wall covered with nylon sheet of 3mm thick 5 Amp 3 pin for open PVC plug point SD 36

Supply and fixing of 1200 mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 m down rod with fan clamp with side plates and across arm of size 450mm (18") SD 110

Supply and fixing of single box type 4'20 W flu fitting complete with tube copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheated leads from terminals to the fitting SD 88

Supply and fixing of fancy glass shade and 7 W /9w LED Bulb

Supply and fixing of LED bracket with Twin box type Street light fitting complete with electronic ballast with all accessories SD 447

ii) Water Supply Arrangements

Supply and delivery PVC Pipe including cost and Conveyance etc complete.,

110 mm Pvc Pipe

75 mm Pvc Pipe

20 mm Pvc Pipe

Earth Excavation and depositing on bank for with an initial le.ad and lift as per hard gravely soil for pipe line etc complete.

Laying of PVC rigid pipes with lead of 200m lowering into trench, laying in proper grade, alignment, jointing PVC coupler with specials etc complete., 110mm dia PVC pipe

Laying of PVC rigid pipes with lead of 200m lowering into trench, laying in proper grade, alignment, jointing PVC coupler with specials etc complete., 20mm dia PVC pipe

Re-filling with excavated soil compplying with standard specification in layers of 15cm thick well rammed and consolidated after pipes and specials etc complete.,

Supply and delivery of PVC / GI pipe Specials including all cost and conveyance etc complete.

20 mm dia PVC Elbow

20 mm dia PVC Tee

25 mm dia PVC Nalli

110mm dia PVC Elbow

75 mm dia PVC Elbow

Supply and delivery of 1000 lit capacity HDPE tank as per IS 12701/1996

Supplying and fixing in positon European water Closet earthern ware of approved quality and brand with "P" or "S" trap with double flapped seat and seat cover with bran hinges and 10 lit PVC low level flushing tank with all fittings including giving necessary connection to PVC pipes etc., complete

Supplying and fixing of PVC Panelled door Shutters Hollow type - 200mm x 20mm Panelswith iron wall thickeness for panels and styles of Suitable size with 2 mm wall thickness with reinforcement using MS angles / flat complete complying with standard specification.

Providing Paver Block With Path Way AT Distirct Relief Coordination Centre To Collector Office Campus Pavement

Earth work Excavation for Formation in all soils and Sub Soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of Formation as per SS20A For Core Wall Foundation

Cement concrete 1 : 4 : 8 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Cement concrete 1 : 3 : 6 mix using 20mm HBG metal for core wall cost and conveyance of all material to site including labour charges for mixing laying compacting and curing etc., complete complying with standard specifications and as directed.

Construction of Granular Sub base by providing well graded material (25 mm to 4.75 mm IRC HBG metal @ 65 %,4.75 to 2.36mm IRC HBG metal @20%&2.36 mm below IRC HBG metal @15%)& (the material passing 425 microns sieve shall have liquid limit and plasticity index not more than 25 & 6% repectively) spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with rotovator at OMC and compacting with three wheel 80-100 KN capacity and finished in accordance with the requirements of the specification and thickness as per approved plans or as directed by the Engineer (Mix -in - place method) .

Providing and Laying Paver Block of 60mm thick approved design made out of 12mm and 6mm HBGS chips in M30 mix properly cured to attain the required strength, Laying and interlocking block and well compacted using 1-3 ton capacity compressor, the cost inclusive of all materials for manufacturing, interlocking block loading transportation to work site unloading and labour charges for fixing over Sand bed of 30mm thick & Joints filling using compressor of 1-3 ton capacity including hire and fuel charges for compressor and all other incidental charges etc complete.

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

Please Enable Macros to View BoQ information