PROVISION OF PARKING SHED FOR CAR AND TWO WHEELER AND CERTAIN OTHER MINOR WORKS AT 24 ED AF STATION MANAURI

Amount

Surface excavation n.exc 30cm deep and averaging 15 cm deep and getting out in soft/loose soil etc

Excavating in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for wall foundation etc or for manholes etc not exceeding 10 Sqm area on plan and not exceeding 1.5 metre in depth and getting out in soft/loose soil.

Returning filling in foundation/trenches including spreading leveling, watering and well ramming in layers not exceeding 25cm thick complete.

Earth filling under floor in layers not exceeding 25cm thick & well ramming and watering as required.

Removing excavated surplus soil n. exc 50 metre and deposited where directed at a level n.exc 1.5 metre above the starting point complete.

M&L for hard core of broken stone or boulders guage not exceeding 63mm, deposited, spread and levelling in layers not exceeding 15 cm thick, watered and rammed to true surface

M&L for provide Cement concrete 1:4:8 type D-2 (Using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete

M&L for provide PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping, cills etc including necessary form work.

M&L for brick work with fly ash bricks, (old size) straight or curved on plan exc 6m mean radius, built in cement and sand mortar (1:6) complete

M&L for brick work with with fly ash bricks, (old size) straight or curved on plan to any radius in half brick thick walls built in cement and sand mortar (1:4)

M&L for provide 40 mm thick damp proof course 1:2:4 using 12.5mm graded crushed stone agreegate mixed with liquid water proofing compound as per manufacturers instructions including necessary form work complete as directed. Note:- water proofing compound shall be measured & Paid separately under respective item of this schedule as supply only.

Supply only integral water proofing compound.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work not exceeding 200mm thick (horizontal or slooping) flat rough finished surfaces of concrete complete.

Use & waste of form work to edge of concrete flats, roof/ shelves not exceeding 200mm wide, sides of bands in walls and similar work exceeding 100mm but not exceeding 200mm wide, rough finished surface of concrete.

S&F Solid PVC door frame size 50mm x 47mm made out of 5mm plain colour (wood grain finish) PVC sheet reinforced with M S square tube as per specification & drawing on page No. 160 of MES SSR Part-I

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC (wood finish) ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing of MES SSR Part-II. Note :-Frame for fixing shutter, hinges, builder hard ware shall be measured and paid for separately under repective item of this schedule.

S&F extruded aluminium alloy handles anodised 150mm long fabricated type, ISI marked complete all as specified & directed.

S&F aluminium anodised barrel tower bolts extruded section 150mm long, ISI marked complete all as directed.

S&F 300mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S & F Steel ventilator with top hung shutters including hinge with steel handle and steel peg stay complete as specified & directed by Engineer-in-Charge.

Supply & Fixed sheet glass 3 mm thick ordinary quality in Square or rectangular in shape not exceeding 0.5 Sqm each pane and glazing with oil putty or steel pins complete all as specified & directed by Engineer-in-Charge.

S&F 100mm size butt hinges with mild steel cold rolled medium weight

S&F structural steel work i.e. rolled mild steel in joist, channel, angle or tee sections in truss with connecting plate etc, comforming to Fe-410-W (Gde E-250) quality 'A'.

S&F for steel reinforcement mild steel TMT bars, 8mm dia, cut to length bent to shape required crankng, hooking end and binding with and including mild steel wire (annealed) not lkess than 0.90 mm dia.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screws as specfied.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screws as specfied.

M&L for 75 mm thick PCC (1:3:6) type C-2 , using 40 mm graded crushed stone aggregate as in plinth protection laid in panel not exceeding 3 metre surface shall be finished even and fair.

M&L for 25mm thick plain cement concrete type B0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) as sub base of tile.

M & L for 7 to 8 mm thick joint free non-skid ceramic coloured tiles ( square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete Note:- Quoted rate shall deem to included cost of bedding layer.

M&L Glazed ceramic coloured tile in vertical surface of size 300 mm x 450 x mm x 7-8mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment over & including bedding layer or screed bed or bedding layer in 10 mm thick cement sand mortar 1:4 complete as specified & directed by Engineer-in-Charge.

M&L for machine pressed precast concrete interlocking paver block with heavy duty glossy finish designer pattern coloured any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade laid over 25mm thick sand cushioning including filling of joints with sand complete. Note :- (i) Quoted rate shall deem to be included cost of 25mm thick sand cushioned below paver and during compaction. (ii) Design and colour of paver block shall be as approved by AGE(I).

M&L for 15mm thick rendering in cement and sand mortar (1:6) on fair faces of brick work surfaces finished even and fair without using extra cement.

M&L for 10mm thick rendering in cement and sand mortar (1:3) on ceiling surface finished even and smooth without using extra cement

M&L for preparing new plastered surfaces of walls applying three coat of white wash on walls all as specified and as directed.

M&L for preparing new plastered surfaces of ceiling and applying three coat of white wash on ceiling

M&L for preparing of new plastered surface of wall and apply two coat of cement paint over a coat of primer.

M&L for preparing new or previously untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete.

S&F 15mm dia Tubes, ‘medium grade’ galvanised, with all fitting fixed on concealed in walls and ceilings or laid in trenches etc and testing. Note :- Excavation and earth work shall be measured and paid for separetely under respective item of this schedule.

S&F 20mm dia Tubes, ‘medium grade’ galvanised, with all fitting fixed on concealed in walls and ceilings or laid in trenches etc and testing. Note :- Excavation and earth work shall be measured and paid for separetely under respective item of this schedule.

S&F rotational moulded polyethylene cylindrical vertical with closed top water storage tank 'White' double layered 500 Ltr capacity, hoisted and fixed in position and making GI tubing inlet or outlet connection including ball brass valves high pressure of with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed 20mm dia polythene floated fly nut, tank nipple, 2 Nos 20mm dia union, wash out pipe etc complete.

S & F vitreous china WHB white colour of size 550X400 mm flat back or angle back type including angle iron bracket, waste coupling, PVC waste pipe 32 mm dia 60 cm long fixed pinning in ends of brackets, compete all as specified and directed.

S&F Vitreous china squatting pan, orissa pattern, size 580x440 mm white, with integral foot rests including connection to trap and to flushing pipe, anti syphonage pipe including making good to floor with PCC 1:2:4 or cement sand mortar 1:3 complete all as specified and directed by Engr - in - charge.

S & F PVC valveless, syphonic action type, flushing cistern, low level, white colour capacity 10 liters with inlet and outlet, ball valve, handle including cast iron brackets & 32 mm bore PVC flush pipes, compete all as specified and directed.

S & F PVC (SWR) pipes, single socketed, in any length, with rubber rings 110mm dia and fixed in position such as wall, ceiling, or laid in floor complete all as specified and directed

S&F 110mm PVC (SWR) bends any radius. complete all as specified and directed.

S&F PVC SWR floor trap, 110mm outlet dia, plain with grating including jointing with solvent cement.

S & F PVC connections 15mm size with PTMT nuts and bolts of length 450mm etc complete all as specified and directed

S&F angle valve of 15 mm bore CP high pressure screwed for iron pipes or brass ferrule compete all as specified and directed.

Supply & fixing in position of Gun metal Gate or globe valve with iron wheel head, screwed both ends for iron pipes of size 20 mm bore complete all as specified & directed.

S&F Pillar taps, 15mm bore CP with with capstan heads, long body screwed down, screwed for lron pipe high pressure with lettered "hot or Coled" with long shank compete all as specified and directed.

M&L Sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 6sqmm FRLS, 1100 Volts grade cable drawn into and including stove enamelled steel Conduit of size not less than 20mm dia including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 6 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 6 sqmm cable and one run of 6 Sqmm cable as earth lead with stove enamelled steel conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish. Make :- As specified in Appendix 'B' (list of Makes) to Particular specifications.

M&L Sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 4sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of size not less than 20mm dia including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 4 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 4 sqmm cable and one run of 4 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish. Make :- As specified in Appendix 'B' (list of Makes) to Particular specifications.

M&L Sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 1.5 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of size not less than 20mm dia including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 1.5 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 1.5 sqmm cable and one run of 1.5 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish. Make :- As specified in Appendix 'B' (list of Makes) to Particular specifications.

Supply and fixing single pole and neutral 2 way single door type with 240 volt MCB/ isolator sheet steel enclosure distribution board complete.

S&F MCB, DP, 240 volts, 40 Amps, 50Hz, 10 KA, 'C' series in accordance with IS/IEC 60947-3 complete and as directed.

S&F Ceiling rose, 3 terminal , PVC, polycarbonate insulated body

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS PVC cable IS:694 with multi stranded copper conductor of size 1.5 sqmm (Nominal area) drawn through and including rigid PVC conduit/ metelic conduit ISI marked not less than 20 mm dia with all PVC conduit fittings such as Tees, elbows, bend, reducers etc, concealed conduit wiring fixed on wall/ on ceiling with GI saddles, GI screws, rowel plugs (surface conduit wiring) with all fittings including tee, junction boxes and provision of pressed steel terminal box 1.25 mm thick of suitable size with 3 mm thick plastic laminated sheet cover for mounting switch sockets and regulators and drawn continuous earth wire with and including PVC insulated unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) connected to earth dolly complete all as specified and as directed by Engr-in-Charge for One light/fan point controlled by one switch. Note :- (i) The cost of chases cutting on wall for concealing conduit, boxes, plate etc are included in the unit quoted rate. (ii) Switches, sockets, etc shall be measured and paid for separately.

All as per item No 59.00 above but One 5 pin 5 Amps socket out let point on same board controlled by one switch.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS PVC cable IS:694 with multi stranded copper conductor of size 1.5 sqmm (Nominal area) drawn through and including stove enamelled steel conduit ISI marked not less than 20 mm dia with all stove enamelled steel conduit fittings such as Tees, elbows, bend, reducers etc, concealed conduit wiring fixed on wall/ on ceiling with GI saddles, GI screws, rowel plugs (surface conduit wiring) with all fittings including tee, junction boxes and provision of pressed steel terminal box 1.25 mm thick of suitable size with 3 mm thick plastic laminated sheet cover for mounting switch sockets and regulators and drawn continuous earth wire with and including PVC insulated unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) connected to earth dolly complete all as specified and as directed by Engr-in-Charge for One 5 pin 5 Amps socket out let point on independent board controlled by one switch. Note :- (i) The cost of chases cutting on wall for concealing conduit, boxes, plate etc are included in the unit quoted rate. (ii) Switches, sockets, etc shall be measured and paid for separately.

All as per item No 61.00 above but One 5 pin 5 Amps socket out let point on same board controlled by one switch.

All as per item No 61.00 above but power point wiring for 15 Amps socket outlet using 2.5 sqmm copper conductor cable FRLS insulated unsheathed for phase and neutral and 2.5 sqmm as earth wire complete.

S&F of switch piano flush type 5 Amps single pole one way 230 volts complete.

S&F socket outlet , 5 pin 5 amps 230 volts flush type, multipurpose complete.

S&F Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V

S&F Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth

S&F Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 25A, 250V, 2P+earth

Supply and fixed sheet metal enclosure for MCB distribution board double door, SPN, 8 way with 200 Amp rated bus bar 230 Volts complete.

Supply and fixed sheet metal enclosure for MCB distribution board single door, SPN, 4 way with 200 Amp rated bus bar 230 Volts complete.

S&F MCB, Single pole and neutral, 230 volt, 40 Amp rating 10KA, C series fixed in DBs catered herein before.

S&F MCB, SP, 230 volts, 6 to 32 Amp rating, 10 KA, C series fixed in DBs catered herein before.

M&L for sand cushioning (dry ganga sand) to under ground cable for cable protection with layer of 8 cm deep before laying the cable and 15 cm depth after laying the cable, complete all as specified and as directed by Engr-in-Charge. Note : Only punned thickness of sand will be measured and paid.

M&L for brick, sub class 'B' well burnt, laid dry flat in trenches for protection of cable over LT/HT cable, complete all as specified and directed by Engr-in-Charge.

Labour for boring to hard standing/ plinth protection/ road etc in depth minimum 60 CM for crossing the GI pipe 40/80 MM dia of bore complete all as directed. Note :- Quoted rate shall be included cost repair to disturbed surface as site.

Supply, fixing on surface of wall / beam pole etc and laid in trench GI tubing light grade in size 40 MM dia of bore with all fittings complete.

Supply, laid in trench/ fix/ thembling/ glanding/ clamping on surface of wall / beam/ roof etc XLPE insulated armoured heavy duty electric power cable (E) with aluminium conductor 1100 volts garde cross sectional area 95 Sqmm x 3.5 core (earthed) complete.

Supply, laid in trench/ fix/ thembling/ glanding/ clamping on surface of wall / beam/ roof etc XLPE insulated armoured heavy duty electric power cable (E) with aluminium conductor 1100 volts garde cross sectional area 50 Sqmm x 3.5 core (earthed) complete.

Supply, laying & testing XLPE insulated armoured heavy duty electric power cable (E) with aluminium conductor 1100 volts garde cross sectional area 10 Sqmm x 2 core (earthed) complete.

Supply and fixing LED tube light fitting complete with frame, driver etc in 20 W 4 feet long white colour mounting on tow Nos of PVC round/ square block on surface of wall / beam etc incl making all electric connection using three core copper cable drawn through in PVC flexible conduit pipe from ceiling rose to fittings complete in all specification with connecting accessories as directed. Note:- (i) Make:- Bajaj cat No BCLSB 20 WH or equivalent model of make Phillips/ Wipro/ Crompton . (ii) Light fitting of other make of higher capacity may be used without any price adjustment.

Supply and fixing LED tube light fitting complete with frame, driver etc in 10 W 2 feet long white colour mounting on tow Nos of PVC round/ square block on surface of wall / beam etc incl making all electric connection using three core copper cable drawn through in PVC flexible conduit pipe from ceiling rose to fittings complete in all specification with connecting accessories as directed. Note:- (i) Make:- Bajaj cat No BCLSB 10 WH or equivalent model of make make Phillips/ Wipro/ Crompton (ii) Light fitting of other make of higher capacity may be used without any price adjustment.

Supply and fixing exhaust fan 300 mm sweep steel body heavy duty with louver mounting bracket ISI marked 4 star rated energy saving less noise capacitor type incl making hole in brick wall plastering colour coading and all site required work for disturbed surface matching with existing and making electric connection using three core copper cable drawn through in PVC conduit pipe complete all as specified and directed. Make:- Crompton Greaves / Havells/ Khaitan /Bajaj/ Orient/ Usha

M&L for earthing for LT panel feeder pillar complete with galvanised mild steel earth electrode plate 600 X 600 X 6 mm thick buried directly and vertically in ground connected to galvanised iron earth strip 32x6mm size by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanised iron 40 mm bore medium grade pipe with all fittings from the earth electrode fixed along pole with and including 25 x 6mm flat iron clamp, bolts, nuts and washers and watering pipe shall be 20 mm bore GI medium grade from top of the earth electrode to bottom of the earth pit including all excavation and earth work in any type of soil and removal of surplus soil upto 50 metre, PCC pit with pre-cast RCC cover with handle, charcoal/salt, funnel , CI frame etc complete all as directed. Notes :-(i) The concrete pit shall be made in PCC 1:3:6 type C-1, 40mm thick precast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate with suitable MS handle in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. Reinforcement in RCC cover shall be of 8mm dia TMT bars laid @150mm c/c both ways. (ii) Item includes the cost of 7.5 metre GI pipe for protection of earth strip. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 metre earth strips. Any variation in length shall be adjusted through deviation order. (iv) Plate electrode shall be surrounded by adequate quantity of charcoal dust & salt to a packed thickness of 15 cm on all sides.

Supply. Installation, testing and commissioning of LT feeder pillar box in cubical housing cabinet, outdoor type, platform mounted (minimum height 45 cm above normal GL and 30 cm below normal GL) , CPRI approved factory made, totally enclosed, dust and vermin proof made out by 3.15 MM thick CRCA MS sheet of overall indicating size 750 x 650 x 450 MM and full built upon angle iron frame in size 40 x 40 x 6 MM, having front and rear hinged both side openable doors and lifting lugs (02 Nos) , locking arrangement to be connect to earthing strip at rear side, bottom detachable both side openable ,gland plate complete with suitable size zinc plated and passivated nut, bolts, spring and washers sheet steel bus bar chambers having front hinged covers with a set of electrolytic grade high conductivity. Contd... on Srl 84.01

Contd.......Srl No 84 - The cabinet and all members should be chemically treated with MSR solution for anticorrosive treatment. The panel shall be epoxy powder coated and the control circuit shall be connected by multi stranded copper conductor flexible wire 1.5 Sqmm in proper colour coding and drawn through in flexible conduit. The panel should be suitable for 415 volts ,50 Hzs, 3 phase,4 wire system ,suitable rating CTs and PTs . internal connection should be made by copper strip in suitable rating ,making incoming and outgoing connection using gland in suitable size including grouting KIOSK on floor (60 CM above the ground surface) in floor angel iron 50 x 6 MM imbedded to fixed the KIOSK with nut bolt, floor PCC (1:2:4) type B1 using 20 MM grade stone aggregate ( minimum 50 CM above GL and 30CM below GL) complete comprising the following items:- (a) 04 Nos bus bars equal size made out of Copper conductor strip in colour coating 600 Amps rated mounting on both side heat shrinkable insulators and PVC sleeves. -01 Set (b) LED indicating lamps of 'R' 'Y' and 'B' phase. Set of three -01 (c) Digital volts meter rating 3 phase class 1 - 01 No Make :- L&T WDS 301FE 00 (d) Digital Ammeter rating 3 phase 1A class 1 - 01 No Make :- L&T WDS 301OCA 00 (e) MCCB ,125 Amps rated, 4 pole, 415 volts grade , 25 KA breaking capacity adjustable thermal based operated - 01 No (As main incomer) Note : (i) Panel drawing shall be approved by Deptt for size/qty/ Tech specification before placing order (ii) All MCCB shall be confirming to Icu 100% and IEC 60947 -2 . in compact series (iii) All out going feeder shall be connected by cable through suitable size of gland plate/glands. (iv) The various feeder shall be indicated by 50mm size letters in synthetic enamel white paint. Make of MCCB : as per specified in list of make Appendix 'B' to particular specifications.

M/S R S Traders

M/S Garg Sons

R K CONSTRUCTION COMPANY