SPL REPAIR TO LT OVERHEAD CONDUCTORS BY REPLACING INTO LT UNDERGROUND CABLE AT SUB STATION NO 05 AND ITS CONNECTED AREAS AT CME PUNE

Amount

Dismantling of ACSR or AAC conductors and removing old material from site for taking credit.

Dismantling concrete poles/struts of any size and removing old material from site for taking credit and making good the disturbed surfaces all as specified/directed by Engr-in-Charge

Dismantling insulators any type, any size and revoming old material from site for taking credit

Dismantling cross arms of MS channel or angle sections etc complete and removing old material from site for taking credit

Dismantling and taking out old unsv XLPE cable any size alongwith DWC pipe and setting aside for credit complete.

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep and making good surface for laying /removing of cable all as specified and directed by Engr in charge as in

(a) Soft/loose soil

(b) Hard/dense soil

(c) Soft/disintegrated rock.

Excavation in trenches n exc 1.5m wide and depth beyond the first 1.5 m and making good surface for laying /removing of cable all as specified and directed by Engr in charge.

Returning filling in excavated soil in trenches, watering and well ramming in layers n exc 25 cm complete all as specified.

Removal of surplus excavated soil to distance n exc 50 metre all as specified and directed

M & L for bituminous road cutting to a width of 45 cm and depth 50 cm for laying of pipe for laying of UG cables and making good with PCC (1:3:6) type cI (using 20mm grade stone aggregate)

M&L PCC(1:4:8) type D-2 using 40mm graded stone aggregates as in foundadion filling and mass concrete ( for foundation bed concrete in stay poles or any other directed site ) complite all as specific and directed

M&L PCC(1:3:6) type C-2 using 40mm graded stone aggregates as in foundadion filling and mass concrete ( for foundation bed concrete in stay poles or any other directed site ) complite all as specific and directed

M&L PCC(1:2:4) type B-1 using 20mm graded broken stone aggregates as in foundadion filling and mass concrete ( for coping above ground level in stay poles or any other directed site ) complite all as specific and directed by Engr-in-Charge.

Supplying and laying GI tubing light grade of size 40mm dia bore for encasing cables for mechanical protection , laid under Plinth / Floors/ Paths Culverts or fixed on wall or concealed in wall/floor or along poles or as street light poles or as street light mounting bracket with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works all as specified and directed by Engr-in-charge.

Supplying and laying GI tubing light grade of size 50mm dia bore for encasing cables for mechanical protection , laid under Plinth / Floors/ Paths Culverts or fixed on wall or concealed in wall/floor or along poles or as street light poles or as street light mounting bracket with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works all as specified and directed by Engr-in-charge.

Supplying and laying GI tubing light grade of size 80mm dia bore for encasing cables for mechanical protection , laid under Plinth / Floors/ Paths Culverts or fixed on wall or concealed in wall/floor or along poles or as street light poles or as street light mounting bracket with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works all as specified and directed by Engr-in-charge.

Supply , laying and testing cable XLPE insulated screened pvc bedded galvanised steel strip or wire armoured , electric power cables ( heavy duty) with stranded aluminium conductor 1100 volts grade in trenches/ passing through pipe/fixing on walls, floors etc incl connection with proper sizes lugs and gland, suitable clamp of cross sectional area 4 core 16 Sqmm all as specified and directed.

All as per item 17 above but of the size 4 core 25 Sqmm

All as per item 17 above but of the size 3.5 core 35 Sqmm

All as per item 17 above but of the size 3.5 core 50 Sqmm

All as per item 17 above but of the size 3.5 core 70 Sqmm

All as per item 17 above but of the size 3.5 core 95 Sqmm

All as per item 17 above but of the size 3.5 core 120 Sqmm

All as per item 17 above but of the size 3.5 core 150 Sqmm

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 50 mm and inner dia 38 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl couplers & bends complete all as specified. Make : REX POLYEXTRUSION LTD or its equivalent as approved

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 77 mm and inner dia 63 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl couplers & bends complete all as specified. Make : REX POLYEXTRUSION LTD or its equivalent as approved

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 90 mm and inner dia 75 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl couplers & bends complete all as specified. Make : REX POLYEXTRUSION LTD or its equivalent as approved

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 120 mm and inner dia 103 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl couplers & bends complete all as specified. Make : REX POLYEXTRUSION LTD or its equivalent as approved

S&Fcable route marker with suitable rainforcement of size 50x20x10cm with latter inscribed on both side as MES LT CABLE of specified ront side not les then 60mm as directed and mounted on pcc 40x30x30 cm complete using PCC 1:2:4 B-1 using 20mm graded stone aggregade and including painting using cement bsed paint to the satisfaction of Engr in Charge .

M & L and erect in true vertical position (or to be fixed in an inclined position as strut pole) steel tubular swaged poles complete with MS base plate of 6 mm thick of size 300 mm x 300 mm, finial taper plug, pole cap, bolts, nuts and washers and screwed pole made out of FRW MS tubing conforming to IS-2713 (Part-II) 1980 type 410-SP-31 ( 9 meters long ) pole including drilling of holes of required size and Nos for fixing of cross arms, painting with one coat of red oxide primer and two coats of aluminium paint for exposed surfaces and two coats of black bituminous paint for portion embeded in concrete, etc complete all as specified and directed

Supply, installation, testing and commissioning weather and vermin proof factory made CPRI approved LT feeder pillar box IP 65, out door cubicle/KIOSK type totally enclosed outer cage made out of 3.15 mm thick sheet metal and inner compartments of 2.0 mm thick sheet metal enclosure with angle iron frame of MS angle 50x50x6 mm grouted in CM, 45 cm below ground level and 60 cm above round suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber /wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated internally/ externally of approved colour with PCC foundation and aluminum bus bar for 3 phase & neutral mounted on epoxy insulator-01 Set, size 1.2 x 1.0 x 0.5 Mtr (approx) including connecting the following:- Location - Inside INI Near OR,s guest Room, Proposed Panel No-5 on site plane.

(j) Provision of cubicle to accommodate the above mentioned accessories. (k) Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Supply, installation, testing and commissioning weather and vermin proof factory made CPRI approved LT feeder pillar box IP 65, out door cubicle/KIOSK type totally enclosed outer cage made out of 3.15 mm thick sheet metal and inner compartments of 2.0 mm thick sheet metal enclosure with angle iron frame of MS angle 50x50x6 mm grouted in CM, 45 cm below ground level and 60 cm above round suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber /wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated internally/ externally of approved colour with PCC foundation and aluminum bus bar for 3 phase & neutral mounted on epoxy insulator-01 Set, size 1.2 x 1.0 x 0.5 Mtr (approx) including connecting the following:- Location - Inside INI Near OR,s Line, Proposed Panel No-6 on site plane.

(j) Provision of cubicle to accommodate the above mentioned accessories. (k) Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Supply, installation, testing and commissioning weather and vermin proof factory made CPRI approved LT feeder pillar box IP 65, out door cubicle/KIOSK type totally enclosed outer cage made out of 3.15 mm thick sheet metal and inner compartments of 2.0 mm thick sheet metal enclosure with angle iron frame of MS angle 50x50x6 mm grouted in CM, 45 cm below ground level and 60 cm above round suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber /wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated internally/ externally of approved colour with PCC foundation and aluminum bus bar for 3 phase & neutral mounted on epoxy insulator-01 Set, size 1.2 x 1.0 x 0.5 Mtr (approx) including connecting the following:- Location - Back side of East wing mess Proposed Panel No-3 on site plane.

Supply, installation, testing and commissioning weather and vermin proof factory made CPRI approved LT feeder pillar box IP 65, out door cubicle/KIOSK type totally enclosed outer cage made out of 3.15 mm thick sheet metal and inner compartments of 2.0 mm thick sheet metal enclosure with angle iron frame of MS angle 50x50x6 mm grouted in CM, 45 cm below ground level and 60 cm above round suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber /wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated internally/ externally of approved colour with PCC foundation and aluminum bus bar for 3 phase & neutral mounted on epoxy insulator-01 Set, size 1.2 x 1.0 x 0.5 Mtr (approx) including connecting the following:- Location - Near Car Wash, Proposed Panel No-4 on site plane.

(j) Three pole Contactor 63 A Current Rating 70A General use 10A, 415V with coil Make L&T Model MNX 70 Three pole contactor complete. Make L&T cat part No CS97076/Legrand/schneider - 01 N0 (k) Digital timer switch with inbuilt backup current capacity 16 Amps operated on 415 volts AC 50Hz, Make: Indoasian cat part No TDA43111/ Legrand/Indoasian - 01 No (l) Provision of cubicle to accommodate the above mentioned accessories. (m) Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Supply, installation, testing and commissioning weather and vermin proof factory made CPRI approved LT feeder pillar box IP 65, out door cubicle/KIOSK type totally enclosed outer cage made out of 3.15 mm thick sheet metal and inner compartments of 2.0 mm thick sheet metal enclosure with angle iron frame of MS angle 50x50x6 mm grouted in CM, 45 cm below ground level and 60 cm above round suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber /wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated internally/ externally of approved colour with PCC foundation and aluminum bus bar for 3 phase & neutral mounted on epoxy insulator-01 Set, size 1.2 x 1.0 x 0.5 Mtr (approx) including connecting the following:- Location - Near ET Quarter, Proposed Panel No-1 on site plane.

(h) Provision of cubicle to accommodate the above mentioned accessories. (j) Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Supply, installation, testing and commissioning weather and vermin proof factory made CPRI approved LT feeder pillar box IP 65, out door cubicle/KIOSK type totally enclosed outer cage made out of 3.15 mm thick sheet metal and inner compartments of 2.0 mm thick sheet metal enclosure with angle iron frame of MS angle 50x50x6 mm grouted in CM, 45 cm below ground level and 60 cm above round suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber /wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated internally/ externally of approved colour with PCC foundation and aluminum bus bar for 3 phase & neutral mounted on epoxy insulator-01 Set, size 1.2 x 1.0 x 0.5 Mtr (approx) including connecting the following:- Location - Inside INI Near Vijay Hall, Proposed Panel No-7 on site plane.

(a) Aluminium bus bar rectangular 400 Amps full for phase and half for neutral mounted on epoxy insulators with colour coding PVC sleeves.-01 job (b) MCCB 200 Amps, TPN, 415 Volts, 50 Hz , 25 KA - 01 No ( Incoming) (c) MCCB 160 Amps, TPN, 415 Volts, 50 Hz , 16 KA - 01 No ( Outgoing) (c) MCCB 100 Amps, TPN, 415 Volts, 50 Hz , 16 KA - 02 No ( Outgoing) (c) MCCB 63 Amps, TPN, 415 Volts, 50 Hz , 16 KA - 03 No ( Outgoing) (c) MCCB 40 Amps, TPN, 415 Volts, 50 Hz , 16 KA - 04 No ( Outgoing) (e) RYB LED Indicator Lamp- Set of Three-01

M & L for fabrication of junction box made out of fibre material complete with TPN ,aluminium bus and suitable for one number MCB (SP) including one No MCB (SP) 10 Amps 240 volts with glands for incoming & out going cable including fixing of flat iron clamps of size 20x4mm on PCC/Steel tubular pole complete all as specified and as directed by Engr-in-Charge. Make: Havells/Sintex.

S&F of PVC insulated cable with copper condcutor 1.5 sqmm three core drwan through pole from pole junction box to street light connector and testing complete.

M & L for earthing complete with GI earth plate electrode of size 60 x 60 x 0.6 cms thick burried directly in ground vertically at a depth of not less than 2.25 Mtrs below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to galvanised iton strip of 25 x 4 mm as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, 40 mm dia GI tubing light grade protection pipe upto test point, 20 mm dia GI watering pipe with funnel and wire mesh, PCC pit 1:3:6 with pit cover of size 30x30 CM made of RCC 1:3:6 with suitable handle, angle iron frame of angle iron size 40 x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling in all as required at site all as specified in plate No 3 of SSR Part-I and directed by Engr-in-Charge.

Priyanka Power line (BID ID -3242017)

Adinath Technical Services (BID ID -3242739)

Mahindra Electric Stores (BID ID -3248135)

ONKAR ELECTRIC AND GENERAL STORE (BID ID -3242971)

Pritam Electro Mechanical Services (BID ID -3241240)

SBS Enterprises (BID ID -3247099)

SHREE VAIBHAV ELECTRICALS (BID ID -3242651)