Maintenance of BSNL Buildings and Staff Quarters in all urban and rural area under Rewari SSA for FY 2025-26 SH- Day to Day Maintenance For six Months

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (a) 1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural soureces : 4 graded stone aggregate 20 mm nominal size)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). (a) Lal Maraundy wood /sal wood

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100 x 58 x 1.90 mm

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand).

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm.

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: (a) Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm).

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved.

Providing and fixing uplasticised PVC connection pipe with brass unions : a) 45 cm length 15 mm nominal bore

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. A) 10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (Flexible pipe.) (a) 32 mm dia

40 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : a) Rectangular shape 453x357 mm

Providing and fixing G.I. pipes complete with G.I. fittings & clamps including cutting & making good the wall internal work - Exposed on wall. a) 15 mm dia nominal bore.

20 mm dia nominal bore.

25 mm dia nominal bore.

Providing and fixing C.P brass bib cock of approved quality conforming to IS :8931 a) 15 mm nominal bore

Providing and fixing C.P brass angle valve for basin mixer and geyser points ofapproved quality conforming to IS :8931 (a) 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Taking out existing wooden door shutter, repair by cutting, chieseling etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 a) Rectangular shape 600x450mm internal dimensions

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : a) 250x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : a) 200 x 10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : a) 125 mm

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -Charge

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : a) White solid plastic seat with lid

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : a)Black solid plastic seat with lid

Providing and fixing white vitreous china water closet squatting pan (Indian type) a) Orissa pattern W.C. pan of size 580x440 mm

Providing & fixing White vitreous china water closet squattingpan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site completewith all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. (a) Orissa pattern W.C Pan of size 580x440 mm

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : a) Flat back wash basin of size 550 x 400 mm.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) a) 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : a) Kitchen sink without drain board i) 610x460 mm bowl depth 200 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in- charge.

Taking out doors, windows and clerestorv window shutters (steel or wood) including stacking within 50 mnetres lead: a) Of area 3 sq. metres and below

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : a) 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: a) Two or more coats on new work .

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. - Internal work - Exposed on wall. (a) 20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same,all as per the direction of Engineer-in-charge

Deduct for not providing hinges in doors, windows or clerestory window shutters with : Stainless steel butt hinges with stainless steel screws : For 2nd class teak wood and other class of woodshutters

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes within 50 metres lead as per direction of Engineer- in-Charge. (a) Internal Work - Exposed on wall

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1cement: 4 coarse sand)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, aving brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for oors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. (a) With stainless steel cover plate minimum 1.25 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated luminium rod with L.P./ H.P.H.D. plastic ball. (a) 15 mm nominal bore, 105 mm long, weighing not less than 138 gms

20 mm nominal bore, 120 mm long, weighing not less than 198 gms

25 mm nominal bore, 152mm long, weighing not less than 440 gms

Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre) (if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account)

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:6 (1 cement: 6 fine sand)

6 mm cement plaster of mix :

1:3 (1 cement: 3 fine sand)

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspectionof work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment shall be made once irrespective of duration of scaffolding.Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required shade and colour complete to give and even shade.

Old work (one or more coats)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete :

New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Repair of water supply accessories/fittings like C.P. brass pillar cocks, long body bib cocks, gate valve etc. by providing brass phase(spindle) if required , rubber washer, thread and white leads etc for proper functioning of the accessories complete as per the direction of Engineer-in-charge.(Rate is exclusive of the cost of brass spindle whcih shall be paid for separatly)

Extra for providing bras spindle (heavy type) in bibcock, stopcock, pillarcock of approved shape /size as per site requiremement in item of repair of n bibcock, stopcock, pillarcock

Checking water supply system for proper supply of water from main outer pipeline to terrace tank and from terrace tank to user accessories complete as per the site requirement and the direction of Engineer-in-charge.

Removing blockage from bath/kitchen WC traps including removal blockage from bends for its proper function to use i/c opening door of Tee and re-fixing the same after removal of leakage. Complete as per the direction of the Engineer –in-Charge.( Item including at the cost for provide T & P, ladder etc.)

Removing blockage of existing sewer line by desludging , making arrangement of rodding , pumping , cleaning the sludge and disposal of the same beyond the municipal limits in prescribed environment friendly manner by mechanical transport then cleaning the sewer line with fresh water complete as per the site condition & as per direction of Engineer-in-Charge including pre-monsoon precautionary measures. .

Cleaning of khurras i/c removal of leaves and rubbish etc. and disposing the same away from the roof etc. all compete as per the direction of the Engineer-in-Charge.

Cleaning of existing manholes by desludging & making arrangement of rodding , pumping & cleaning the sludge and disposal of the same beyond the municipal limits in prescribed environment friendly manner by mechanical transport then cleaning the walls & floors with fresh water complete as per the site condition & as per direction of Engineer-in-Charge .(Circular or rectangular manhole of any depth or size)

Cleaning of septic tank including soak pit by mechanical or manual means including removing waste mattter, sewage, sullage and removal of the same from the site to approve dumping ground upto 15 km lead and finally cleaning with fresh water all complete as per the direction of Engineer in charge.The contractor may visit the site i.e; O/o GMTD wherethe item is to be executed for site conditions, size of tank etc for quoting of his rates.

Repair of flushing cistern by setting right internal arrangement for easy and proper operation including providing and fixing PVC washers wherever required complete as per the direction of the Engineer-in-Charge.

Repairing and Setting right aluminium door by dismantling the door providing necessary pivots hinges etc with necessary screws/nails for easy and proper opening and closing operation and then again refixing the same complete as per the direction of the Engineer-in-Charge.

Welding at site i/c transportation of electric welding set for repairing of section windows, M.S. grills, steel chowkhats, hinges, steel jafferies and other steel members (Upto any floor level) i\c welding, hammering, etc for the smooth operation of the fittings, welding of broken part by welding. (Rate includes cost of labour i.e one welder and beldar and electrodes , tranportation of the welding set and movement of welding set but excludes the cost of the steel members and fittings if required) all complete as per direction of Engineer-in-charge.Rate is for single day in one buiding compound

Providing and Fixing siphon set in PVC cistern of approved quality etc all complete as per direction Engineer - in - charge

Providing and fixing handle for low level flushing cistern etc all complete as per direction of Engineer - in - charge

Taking out old grown trees /plants at different location such as shafts balconies, roof etc upto floor five level including demolishing brickwork, cement concrete so as to remove the roots of the treee/plants all complete and repairing the same with old bricks with cement mortar 1:6 (1 cement : 6 coarse sand) and providing and laying new cement conctrete 1:2:4 (1 cement : 2 Coarse sand : 4 stone aggregate 20 mm nominal size) and finishing with cement plaster of mix 1:4 (1 cement : 4 coarse sand) as per site requirment and disposal of the building rubbish etc & like all complete as per the direction of the engineer in charge. (Note: the agency executing the work shall have to make his own arrangement of in scaffolding, jhulla etc and other T & P and labour required for the item)

Providing and fixing C.P. brass waste of standard pattern for sink or wash basin complete as per the direction of Engineer-in-charge:- a) 32 mm dia

40 mm dia

Providing and fixing pair of iron angle for holding wash basin including removing old rusted angles and fixing new angles in cement mortar etc. complete as per directions of Engineer-in-charge.

Extra for providing powder coated MS butt hinges 100x58x1.90 mm in flush door shutters (if any hinges missed in chowkhat)

Providing and fixing fly proof galvanized M.S wire gauge to door, windows and clerestor windows using galvanized M.S wire gauge with average width of aperture 1.4mm in both directions with wire of dia meter 0.63mm with nails and murrandy wood beading wherever required including dismantling of old unserviceable wire gauge all complete (Area opening for panel inserts excluding portion inside grove/rebate).

P/F PVC cover on PVC water storage tanks of capacity 500 litre to 2000 litre with necessary locking arrangements screw nuts etc complete as per direction of Engineer - in -charge.

Providing and fixing C.P. brass pillar cock 15mm nominal bore of approved quality conforming to IS specifications complete as per directions of Engineer-in-charge.

Providing and fixing stainless steel grating(Jali) with or without hole for waste pipe floor trap etc complete.:- (a) 100 mm diametre

Repairs to cement concrete flooring of thickness 40mm in patches of area 2.5 sq. metres and under including cutting & dismantling the patch in proper shape and preparing the sub grade and repairing with Cement concrete of mix 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry all complete including disposal of rubbish to the dumping ground within 50 metres lead.

Providing and fixing brass ball valve with of approved quality (screwed end) : a) 15 mm nominal bore.

20 mm nominal bore.

25 mm nominal bore.

32 mm nominal bore.

Taking out of unserviceable materials i/c dismantling fittings upto any floor height and stacking the same within 50 mtr. lead complete as per the direction of Engineer-in-charge. a) Brass bib cock/stop cook / pillar cock / gate valves/angle valves/ball cock/ball valve/waste couplings and like items etc upto 40mm nominal bore

Aluminium/mild steel - handles /tower bolts/ sliding door bolts

Door Closer

Floor Spring

Credit on account of unserviceable material received from dismantling, demolishing or lying at site issued to agency:- a) Brass bib cock/stop cook / pillar cock / gate valves/waste couplings/angle valve/ball valve etc and like scrap.

PVC water tank,cistern ,pvc connections etc and like scrap

Mild steel/ cast iron/ GI scrap, Floor spring, Door closer etc and like material

PTMT Fittings.

Wooden Doors/windows of area 2.00 sqm or below

Please Enable Macros to View BoQ information