PROVISION OF SHED FOR 03 NOS DIESEL GENERATORS AND INDOOR PANELS AT NEW OTM COMPLEX AT DIGLIPUR AND PROVISION OF SHELTER/ SHED FOR 25 KVA DIESEL GENERATOR AND 1 REST ROOM AT FUEL STORAGE FACILITY AT AERIAL BAY, DIGLIPUR

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil.

Excavating in post holes (or similar holes) each not exceeding 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 mtr and making good surface in any type of soil.

Excavating in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 mtr in depth and getting out in hard/ dense soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/ loose or hard/ dense soil.

Removing excavated soil material not exceeding 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point

M&L for PCC Type B2, 1:2:4 (using 40mm graded granite stone aggregate) as in foundations, filling and mass concrete.

M&L for PCC Type D2, 1:4:8 (using 40mm graded granite stone aggregate) as in foundations, filling and mass concrete.

M&L Pre-cast cement concrete Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 complete.

S&F Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F Rolled mild steel as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality-A.

M&L preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

S&F Mild steel bolts of 75 mm long and 12 mm dia purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut.

M&L broken stone or boulders hardcore of guage exceeding 63mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rolled/ rammed to a true surface.

M&L 75 mm thick PCC Type D2, 1:4:8 (using 40 mm graded crushed granite stone aggregate) laid in sub-floors, sub-bases, floors and pavings, etc. complete all as specified.

M&L 40 mm thick PCC Type B1, 1:2:4 (using 20 mm graded crushed granite stone aggregate) laid in flooring and pavings, etc. finishing cement concrete surface even and smooth without using extra cement complete all as specified.

S&F glass dividing strips, 3 mm thick and 38 mm wide and inserted in position, conform to design.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick or concrete surfaces including mixed with water proofing compound as directed by the manufacturer and finished even and smooth without using extra cement complete all as specified. Note: WPC shall be measured and paid separately.

M&L for preparing new plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete.

Supply only Integral waterproofing compound.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil.

Surface dressing not exceeding 15 cm deep in hard/ dense soil.

M&L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surfaces of concrete

M&L for RCC M-30 design mix for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L formwork to sides of pillars, posts, struts, piers, columns and stanchions for flat fair finished surfaces of concrete.

M&L for RCC M-30 design mix for columns, pillars, piers, posts and struts

M&L for high yield strength deformed TMT steel bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for high yield strength deformed TMT steel bars 5 mm to 10 mm dia cut to length, bent to shape required, as in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

M&L for spreading and levelling in layers not exceeding 25 cm thick, well ramming including watering as required

M&L broken stone or boulders hardcore of guage not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rolled/ rammed to a true surface.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat fair finished surfaces of concrete.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for flat fair finished surfaces of concrete.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges for flat fair finished surfaces of concrete.

M&L for formwork to fins, louvers, fascia for flat fair finished surfaces of concrete.

M&L for RCC M-30 design mix for beams, cantilevers, bressummers, lintels over 1.5m span

M&L for RCC M-30 design mix for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate) precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar, complete, in walls and setting in cement mortar 1:4 complete.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick/ concrete surfaces finished even and smooth without using extra cement.

M&L for rendering 5mm thick in cement mortar 1:4 over 10 mm thick in cement mortar 1:6 on fair faces of brick/ concrete surfaces finished even and smooth without using extra cement.

S&F powder coated of any colour (Thickness or powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, and fixed

S&F 200 mm long aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F anodised aluminium frame for doors, windows, ventilators and partition with one or more rebates including joining cleat for fixing etc. inclusive of rubber neoprene packing and glazing clips for fixing of glass in aluminium frame all as per manufactures catalogue and as directed by Engineer-in-charge.

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples to frame of doors, windows and ventilators including jointing cleat for fixing etc.

S&F 4.80mm thick sheet glass, ordinary quality and glazing with oil putty in squares exceeding 0.50 sq. m in each pane.

S&F 150mm long aluminum handles, cast type.

M&L for two coats of exterior emulsion paint on new plastered surfaces over a coat of alkali resistant primer complete all as specified.

M&L non - skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L screed bed 15mm thick in cement and sand mortar 1:6 on floor surfaces for laying floor finishes complete all as specified.

M&L 25 mm thick PCC Type B0, 1:2:4 (using 12.5 mm graded crushed granite stone aggregate) laid in sub-floors, sub-bases, floors and pavings, etc. complete all as specified.

M&L glazed coloured ceramic tiles in vertical surface 350x 250x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick/ concrete surfaces finished fair and even to receive tiles complete.

S&F Vitreous china wash down water closet pan (Pedestal pattern) white complete including plastic water closet seat cover (White) closed pattern with flat bottom and cover and mild steel chromium plate or aluminium hinging device and connecting to trap anti syphonage pipe etc. and PVC valveless, syphonic action type low level flushing cistern 10 litre capacity, white, with inlet, ball valve, float, handle including brackets, and flushing pipe 32 mm dia etc complete all as specified.

S&F 630 mm x 450 mm size white, flat back vitreous china wash hand basin including PVC waste pipe and 32 mm bore CP waste coupling including CI brackets complete all as directed.

M&L 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

M&L 150x150 mm size salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P'

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches complete all as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches complete all as directed.

S&F 110 mm bore PVC (SWR) Vent cowl fixed complete all as directed.

S&F 110 mm bore PVC (SWR) bends any radius

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal

S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal

S&F 75 mm bore PVC (SWR) bends any radius

S&F 15 mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed.

S&F 15 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F 15 mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down highpressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as directed.

S&F new 500 litres capacity rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer (ISI Marked) white colour both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

S&F 25 mm bore dia of pipe ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S&F 25 mm bore dia of pipe gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

M&L for 15 mm bore new steel water tubing medium grade galvanised (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as directed.

M & L for 25 mm bore new steel water tubing medium grade galvanised (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as directed.

M & L for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including casing and caping with all fittings such as internal bend, end caps etc fixed on the surface of wall, ceiling, roof, steel structure etc. by means of suitable fixing accessories, with GI pressed steel / PVC box suitable for modular switches sunken boxes (with earth dolly) covered with logic modular PVC sheet cover for fixing of switches, sockets etc including PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:- NOTE: - Switch and socket to be measured and paid for separately. (a) One light point controlled by one 5/6 amps one way switch.

(b) One exhaust fan/ fan point controlled by one one way switch.

(c) One Socket outlet, three pin, 6 Amp, controlled by one 6 amps one way switch on independent board.

(d) Security light point.

All as per item No. 80 here-in-above but with 4 Sqmm cables for one 3 pin 15Amps, socket outlet point on independent board .

S&F modular switch 6 Amp, flush type, one way, single pole, 1 module complete. Make: Legrand / Philips / Crabtree

S&F modular switch 16 Amp, flush type, one way, single pole, 1 module complete. Make: Legrand / Philips / Crabtree

S&F modular socket outlet, 3 pin 6 Amp, flush type, 2 modular all as specified and as directed.

S&F modular socket outlet, 3 pin 16 Amp, flush type, 2 modular all as specified and as directed.

S&F ceiling rose, surface bakelite, 65x50 mm, flush type, two to three terminals.

M&L for metal flush box 3 module and white cover plate with frame, 3 module

M&L for metal flush box 6 module and white cover plate with frame, 6 module

S&F 20 Watts surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver etc with complete accessories with all including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make: Havells Cat No. ENDURALINEARNEOBS20WLED830SPCWH or equivalent in Bajaj / Crompton

S&F 22 Watts surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver etc with complete accessories with all including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make: Havells Cat No. ENDURALINEARNEOBS22WLED830SPCWH or equivalent in Bajaj / Crompton

S&F 10 Watts surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver etc with complete accessories with all including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make: Havells Cat No. ENDURALINEARNEOBS10WLED830SPCWH or equivalent in Bajaj / Crompton

S&F sheet metal enclosure DB SPN 8 way for provision of MCBs of different capacities SP 240 V with suitable busbar, double door type with IP-44 protection glass.

S&F MCB SPN 40 Amps, 240 V, 10kA rupturing capacity.

S&F MCB SP 6-32 Amps, 240/ 410 V, 10kA rupturing capacity.

S&F MCB SPN 6-32 Amps, 240 V, 10kA rupturing capacity.

M&L for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filled in alternate layers and electrode connections by using Galvanised earth wire 4mm dia and 7.50 mtrs connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 15 mm dia GI pipe medium grade for protection of GI earth wire and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chamber, MS funnel, wire mesh, 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance not exceeding 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No. 3 of schedule Part-I (2009). Note: (i) The quoted rate shall include for protection pipe, GI water pipe, wire mesh, funnel, excavation, RCC pit cover, PCC chamber pit, test point, 4 mm dia GI wire from top of earth plate upto 5 metres above ground level and if GI protection pipe is less than 5 metres, no price adjustment shall be made. (ii) PCC pit shall be provided at least 500 mm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fitting junction etc shall be deemed to be included in the quoted rate. (iii) RCC pit cover shall be precast of RCC 1:2:4, type B1, 80 mm thick reinforced with XPM (weighing not less than 4 Kg/ Sqm in lieu of cast iron cover).

Supply, lay and testing XLPE insulated, cores laid up, PVC innersheated, armoured with aluminium strip, glavanised wire, heavy duty LT UG electric cable with solid aluminium conductor, 1100 Volts grade, extruded PVC Type ST2 sheathed, conforming to IS: 7098 (Part I) 1988 of cross- sectional area 2 core 10 sqmm.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil.

Supply and laying 40 mm dia bore GI pipe light grade with necessary fittings in trenches/ floor/ pillar/ fixed on pole etc for cable protection .

Supply and laying of DWC (Double Wall Corrugated) HDPE pipe, ISI marked IS 14390 Part-II, of outer dia 50mm and inner dia 38mm with smooth internal and profiled external surface for non pressure underground cable including all connected accessories like coupler, 'O' Ring etc, for protection of cable complete all as specified and as directed. Make: Red Polyextrusion/ Telerex

S&F 1200 mm sweep ceiling fan 230 V, BEE 5 star rated with electronic fan regulator and providing new 3 core 1.5 sqmm copper conductor cable from ceiling rose to ceiling fan with all accessories complete. Make: Crompton HB Plus/ Bajaj / Havells

S&F 300 mm sweep exhaust fan heavy duty 900 RPM, 230 V, 50 Hz, PVC body noiseless type with PVC flush shutter and cable from ceiling rose to fan complete all as specified. Make: Crompton EXHD300-4-1/ Bajaj Maxima Delux / Havells

S&F 30 Watts new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment with IP65 protection and impact resistance of IK07. Make: Havells Cat No. ENDURAPEARLSL30WLED757SASYTOPC or equivalent in Bajaj / Crompton

S&F sheet metal enclosure DB SPN 12 way for provision of MCBs of different capacities SP 240 V with suitable busbar, double door type with IP-44 protection glass.

M&L for submain wiring with 2 runs of 4 Sqmm single core FRLS PVC insulated, unsheathed, multi stranded copper conductor and one single core 4 Sqmm FRLS PVC insulated , unsheathed , multi stranded copper cable as earthing lead as per IS : 694 / 1990 drawn through and including non-metallic PVC rigid conduit/casing caping of size as ordered in walls / ceilings etc complete all as specified and directed. (Note:- 2 runs 4 Sqmm cable, one run 4 Sqmm cable and one run of PVC Conduit/Casing caping shall be measured as one unit length) .

Supply, lay and testing XLPE insulated, cores laid up, PVC innersheated, armoured with aluminium strip, glavanised wire, heavy duty LT UG electric cable with solid aluminium conductor, 1100 Volts grade, extruded PVC Type ST2 sheathed, conforming to IS: 7098 (Part I) 1988 of cross- sectional area 2 core 16 sqmm.

M/s K Moorthi

M/s Kanaka Agencies

M/s Shiva Engineering

MS KAMARIKAR CONSTRUCTION

Govinda Swamy Construction

SWASTHIK ENGINEERING WORKS

M/s Pintu Furniture