SPECIAL REPAIR TO SINGLE LIVING ACCN BLDG NO T12 T13 AND T14 OF 2 FOD AND CERTAIN MINOR AND REVENUE WORKS UNDER AGE BR III AT BB CANTT SRINAGAR

Amount

Dismantling of plain or corrugated steel sheeting of any gauge, thickness including roof covering etc, complete all as specified and directed by Engineer-in-Charge.

S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of an colour having tensile strength of 550 Mpa as in the roof covering/cladding to wall, fixed with shelf tapping screws, complete all as specified and directed.

S&F 0.50mm thick prepainted galvalume aluminum zinc coating GI based Plain steel sheet of any colour having tensile strength of 550 Mpa as in the roof covering / cladding to wall / ridges etc. fixed with shelf tapping screws, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engineer-in-Charge.

M&L for framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15cm thickness below or above GL, complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6 mtr mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan to any radius in half brick thick wall, built in CM 1:4, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in sub base for laying floor finishes etc. complete all as specified and directed by Engineer-in-Charge.

M&L for 18-20mm thick machine cut kota stone flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone/tile including grinding and polishing (mirror finish) (Size of each stone not less than 55cm x 55cm) including roughening of surfaces by pick axices and a coat of cement slurry @ 3 Kg/Sqm of surface over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

Taking down chowkats or frames without taking off shutters from the frame not exc 1.50 Sqm each, complete all as specified and directed.

Taking down chowkats or frames without taking off shutters from the frame exc 1.50 Sqm but not exc 4.0 Sqm each, complete all as specified and directed.

M&L for 1st class soft wood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed at site, complete all as specified and directed.

S&F 35mm thick factory made plain, framed, paneled shutters (two panels) of 2nd class Hard wood with lock rail and panel of 9mm thick B.W.P. commercial ply or 12mm thick veneered particle board with commercial veneering on both faces, sizes of rails and styles as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated, supplied and fitted to chowkats at site, complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick of 2nd class soft wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a), supplied and fitted to chowkats at site, complete all as specified and directed by Engineer-in-Charge.

M&L for galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed by Engineer-in-Charge.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm each pane, complete all as specified and directed by Engineer-in-Charge.

S&F 100mm size butt hinge, medium weight, cold rolled mild steel.

S&F 200mm size aluminium anodised barrel tower bolt of extruded section.

S&F 300mm size aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section.

S&F 150mm size aluminium handle, cast type anodised.

S&F 100mm size aluminium handle, cast type anodised.

M&L for 75mm thick PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection, finished even and smooth without using extra cement including making joints 10mm wide and 30mm deep at spacing not more than 2.5 mtr and at corners mandatory and filled with sealing compound Grade 'A', complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding of any description, fixed in any position with nails, complete all as specified and directed by Engineer-in-Charge.

S&F 6mm thick (05 Nos of ply) plywood, grade BWR, type BB, fixed with screws to timber frame work (wall / ceiling), complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class softwood weather boarding, clean sawn, plain 20mm thick or feather edged 15-20mm thick and fixed with 30mm laps, complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings 40 Sqcm and over in section, in any position, complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hardwood, clean sawn in scantlings, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or old wooden surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tile (heavy duty) with hard glazed rubber topping of size 30cm x 30cm x 25mm thick, set, jointed and pointed in grey cement slurry and pigment as in floors or path over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in coping, benching etc. including necessary formwork / moulds, complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class 'B' bricks in CM 1:4, straight or curved on plan not exc 6 mtr mean radius, complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in cover slabs (for manholes etc.), chullah, hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, complete all as specified and directed by Engneer-in-Charge.

M&L for Soakage well, excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonary with top ring of M-25 grade concrete including intercepting chamber and screen chamber made of brick masonary in CM 1:4, RCC/DWC complete filled with brick bats of size 2.40 Mtr dia X 3.0 Mtr effective depth, complete all as per drawing No. CESZ/TD-1078/2011 Sheet 1/1 and directed by Engineer-in-Charge.

Excavation in trenches not exc 1.50 mtr wide and not exc 1.50 mtr in depth for foundation, shafts, well, cesspits, manholes, pier holes etc. and getting out in any type of soil, complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundation, filling in, sub base and mass concrete, complete as specified and directed by Engineer-in-Charge.

M&L for 15mm thick rendering in CM 1:4 on brick walls with water proofing compound, finished even and smooth without using extra cement, complete all as specified and directed. (Note :- WPC shall be measured & paid separetly under respective item)

Supply only water proofing compound.

M&L for 150mm bore reinforced concrete pipe, class NP-3, laid & jointed complete with collar, complete all as specified and directed by Engineer-in-Charge.

Removing excavated material to a distance exc 250 mtr but not exc 500 mtr and depositing at a level not exc 1.5 mtr above the starting point, complete all as specified and directed by Engineer-in-Charge.

Removing excavated material to a distance not exc 50 mtr and depositing at a level not exc 1.5 mtr above the starting point, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm thick, complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed by Engineer-in-Charge.

Surface excavation in any type of soil, not exc. 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as in sub bases etc, complete all as specified and directed by Engineer-in-Charge.

M&L for 7-8mm thick non-skid coloured ceramic tiles (square/rectangular), area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including 15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles of size 450mm x 300mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 10mm thick rendering in CM 1:3, complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregates), finished even and smooth without using extra cement as in plinth protection, complete all as specified and directed by Enginee-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

S&F stainless steel Peg set with 6 hooks each, complete all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking paver block of any shape and size, confirming to IS:15658-2006, M-35 Grade over and including 50mm thick sand cushioning and including 75mm thick hardcore of gauge not exc 63mm broken sote or boulder, complete all as specified and directed by Engineer-in-Charge.

M&L for hard drawn steel wire fabric, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.90mm in dia, supplied and fixed in reinforement, complete all as specified and directed.

M&L for preparation of newly surfaces steel of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china wash basin, white, flat back of size 580mm x 450mm excluding tap, waste chain and plug and porcelain stopper but including brackets, complete all as specified and directed.

S&F 500 Ltrs capacity rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

S&F 15mm bore angle valve, fancy type, chromium plated with wall flange, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions.

S&F PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F 20mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe.

S&F 15mm bore pillar tap, cast copper alloy with capstan head, chromium plated, fancy type, screwed down, high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F 15mm bore steel water tubing 'medium grade' galvanised with all fitting and fixed complete to wall and ceiling or laid in floors, complete all as specified and directed.

S&F 20mm bore steel water tubing 'medium grade' galvanised with all fitting and fixed complete to wall and ceiling or laid in floors, complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick cement concrete 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregates) as in floor, finished even and smooth with using extra cement, complete all as specified and directed by Engineer-in-Charge.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeeding 0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mm x 200mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 10mm thick rendering in CM 1:3, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over one coat of alkali-resistant primer, complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge.

M&L for walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick rendering in CM 1:4 on stone masonry surfaces of wall and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as in surface channels, bed of drains etc, complete all as specified and directed by Engineer-in-Charge.

Taking down carefully existing aluminium / copper point wiring on batten or in PVC conduit or in MS conduit with earth wire etc. (for light, fan, socket or power) complete and making good the disturbed surfaces of walls, ceilings etc. to match with existing surfaces, complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring for one light/fan/socket point, controlled by one switch with 1.5 sqmm copper conductor cable (multistranded) PVC insulated FRLS (unsheathed) single core 1100 volt grade, drawing in and including casing & caping or in PVC concealed conduit 19mm dia having wall thickness not less than 2mm with cast iron sunk / pressed steel terminal box made out of 1.2mm thick sheet including one coat of red oxide primer on internal and external surfaces covered with 3mm thick hylam brand IS-2036 Marked laminated sheet cover (for mounting switches, sockets, regulators etc.) and including 1.50 sqmm PVC insulated (multistranded) FRLS unsheathed copper conductor cable as continuous earth wire, complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 76.00 above but for one 3/5 pin 5 Amps socket outlet point, controlled by one switch on independent board.

All as per Srl item No. 76.00 above but for one 3/5 pin 5 Amps socket outlet point, controlled by one switch on same board.

All as per Srl item No. 76.00 above but using 2.5 sqmm single core multistranded copper conductor PVC insulated FRLS (unsheathed) cable for 3/6 pin 15 Amps socket outlet, controlled by one switch on independent board with and including 1.5 sqmm green solid copper conductor cable as continuous earth wire with lugs.

S&F lamp holder, insulated body PVC / polycarbonate with back plate suitable for batten fitting, complete all as specified and directed.

S&F ceiling rose three terminals polycarbonate, isolated body, complete all as specified and directed.

S&F switch piano, flush type, single pole, one way 5 Amps, complete all as specified and directed.

S&F switch piano, flush type, single pole, one way 15 Amps, complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 Amps, complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 & 15 Amps, flush type, complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type, complete all as specified and directed.

S&F 20 Watt LED light fitting with fixture, decorative ultra slim with co-extruded channel in thermally conductive material with plastic housing, heat sink, environmental friendly, energy efficient ready to use, complete all as specified and directed. Make :- Havells Cat Part No. LHEXBXPNIN1WO20 or Wipro Cat Part No. LL20-221-XXX-65-NE or HPL Cat Part No. HLPT51820PCGCW or Philips Cat Part No. BN021CLED20SPSUCDLGR

S&F 10 Watt 6000K LED bulk head luminaries with opal diffuser etc. complete with accessories, complete all as specified and directed.

S&F LED 10 Watt (candle / ball type) with B-22 base, complete all as specified and directed.

S&F sheet metal enclosure double door for mounting MCBs with 200 Amps rated bus bar, 8 way, AC 240 Volts with IP-43 protection including cutting chases to wall for fixing DB and making good the disturbed surfaces match with existing surfaces, complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 63 Amps, 240 Volts, 50 Hz AC, made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed.

S&F MCB SP 6-32 Amps, 240 Volts, 50 Hz AC, made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed.

M&L in replacement 10 Sqmm 1100 volts grade, heavy duty, PVC insulated, multistranded aluminium conductor and overall PVC sheathed in service connection, suspended by insulated hangers not more than 1 mtr apart including 4mm dia suspension GI wire one twin core cable flate porcelain insulators etc, complete all as specified and directed.

mirandcompany

M/S AKMAL CONSTRUCTIONS

ZAHOOR ENGINEERING WORKS

M/s Shabir Ahmed Mir and Bros

M/S Vivek Gupta and Co

M/S Gh Qadir

M/S MUSHTAQ AHMAD BHAT

MOHAMMAD YOUSUF MIR

M/S TAJ DIN KHARI

M/S ZENITH TRADE LINK