45/EDCB/2024-25

Amount

The work of safe carriage of the following material from store center Nawada to work site under the jurisdiction of EDD-II, Budaun Approx. distance upto 0-60 Km. Including safe loading and unloading.

P.C.C. Pole 8.5 Mtr Long

ST Pole 11 MTR Long

LT ABC (3x95+1x70+1x16) SQ. MM

LT ABC (3x120+1x95+1x16) SQ. MM

ACSR Rabbit Conductor

Three Phase Distribution Box

Earthing Complete

Stay set Complete

Stay Wire 7/10 Swg

Dropper Channel 100x50MM

Top Channel 100x50x2240

11 Kv Polimic Pin Insulator

11 Kv Polymeric Disc Insulator

GI Wire 6 Swg

GI Wire 8 Swg

GI Wire 10 Swg

TEE-Off Channel

MS Angle 75x75x6x2028

Guarding Angle 50x50x5x2500MM

Cross Arm V-Type 11kv

The following Decentralized material shall be provided by the contractor for execution of work as per RESPO Norms (the material shall be purchased from approved vendor of Discom).

Three Phase Distribution Box Clamp (LS)

Dead End Clamp

Eye Hook

J Hook

Extra For Stay at Angle Location

LT Shackle Insulator

LT Clamp

Clamps with Bolt & Nut

Stone Pad

T, Dropper, Top Channel Clamp for ST/PCC Pole

Cross Arm Holding Clamp

F-Clamp

Stay Clamp

Danger Board with Clamp

Aluminum Paint

Number Plate

Cost of LT Tailess Unit (400A) with 12 no. AI Lugs for 400 sqmm

Erection of the following support including cutting, making holes fixing of all types of accessories digging of pits complete in all respect as per RESSPO norms.

Double pole of ST Pole 11 Mtr. Long. for 100/250 KVA T/F

Single support of ST Pole 11 Mtr. Long.

Single support of PCC Pole 8.5 Mtr. Long.

Grouting of following poles with 1:4:8 mixture in size(450x450x1500mm.) including cost of cement/CC & sand Required as per RESSPO Norms. (All Grouting material shall be provided by the contractor).

Double pole of ST Pole 11 Mtr. Long.

Single support of ST Pole 11 Mtr. Long.

Single support of PCC Pole 8.5 Mtr. Long.

Laying, Stringing, Sagging & Jumpring of Following Conductor complete in all respect as per RESSPO Norms.

LT ABC (3x95+1x70+1x16) SQ. MM

LT ABC (3x120+1x95+1x16) SQ. MM

ACSR Rabbit Conductor

The work of driving the earthing electrode and making connections with GI wire.

Erection/Fixing of stay set with stay wire and clamp as per RESSPO norms including binding. climbing, clamping, tightening and nozzeling etc. complete in all respect including its grouting in ratio 1:4:8 of cement, sand and C.C. and sand etc. as per RESSPO norms. All the grouting material shall be provided by the contractor

Painting of ST Pole 11 Mtr. long. supports with one coat of red Oxide primer and two coats of aluminum white paint of ISI mark and top danger portion of each support must be painted by providing two coat of Post Office Red Paint (1.5 Mtr. Upper portion of support) Paint and material shall be provided by the contractor.

Fixing of danger plate on each location including proper clamping as per RESSPO Norms (Danger Board with clamps & bolts, nuts shall be provided by the contractor)

Fixing of number plate on each location including proper clamping as per RESSPO Norms (Number Plate with clamps & bolts, nuts shall be provided by the contractor)

Guarding of HT/LT/Telephone Line/Road/River crossing etc. and making net with suitable difference. Completely including fixing of all channel/angle etc. with proper locking at each support. All type nut & bolt shall be provided by the contractor.

Construction of 250 KVA T/F plinth 1.5x1.5x2 Mtr. for mounting T/F including foundation work (below ground 0.5 M), Brick work, RCC slab of 4” thickness and plastering in 1:6 ratio with 02 Nos channel pieces of 1.5 mtr long of size 100x50x6 mm compete in all respect as per RESSPO Norms.

Cage fencing of 250 KVA Plinth mounted transformer in Town areas to avoid electrical human/cattle accidents by fabrication of cage (1 Inch Sq wiremesh) made of 10 No gauge in suitable size angle iron frame of size 7.5'(L)x5'(W)x8’(H) by strenghtening of wire mesh 20x3 mm M.S. flat haorizentally as well as vertically, Grouting the panel with 1:2:4 cement/coorse send/brick ballast. The Frame should be bolted on angles at the four corners so that frame may be un-bolted/bolted at the time of replacement of the transformer. Provision of 1 gate should be there for maintenance of the transformer. Painting (1 coat of red oxide + 2 coat of Bus green enamel paint). The wire mesh should be earthed with 50x6 mm MS earthing strip with existing earthing of Transformer Body. All men, material and T&P provided by the contractor to complete the fabrication, transportation and installation.

Pipe Earthing of Transformer (By boring of 4 inch diameter 20 m deep, 40 mm diameter A Class GI pipe is inserted to a depth of 20 m and a holed pipe of 1.5m length is inserted at the bottom, Tighten one end of the MS strip of size 50x6mm with the nut bolt with the neutral of the converter and weld the other end with the GI pipe inserted in the boring for earthing. Putting a socket on the upper part of the pipe (mouth) so that water can be poured into it to retain moisture. To complete the work contractor will provide all material, manpower, T&P, safe carriage of material to worksite. Above work will be carried out under supervision of concerned JE/SDO/EE)

Erraction/Fixing of Tailess Unit (400 A) (Tailess Unit shall be provided by the contractor as per RESSPO Norms). complete in all respect as per

Errection and commissioning of 3 Phase Distribution Box on the LT Poles (All the material required shall be arranged by the contractor for errection and commissioning of distribution boxes except distribution box).

Dismantling and removing of following T/F,s and double pole and shifting at site of the work complete in all respect as per RESSPO Norms.

11/0.4 KV 100 KVA T/F

11/0.4 KV 250 KVA T/F

Mounting of following Transformer as per norms complete in all respect

11/0.4 KV 100 KVA T/F

11/0.4 KV 250 KVA T/F

Dismantling and removing of following 11/LT Lines and poles as per norms complete in all respect.

LT ABC (3x95+1x70+1x16) SQ. MM

LT ABC (3x120+1x95+1x16) SQ. MM

ACSR Rabbit Conductor

Safe back carriage of Following item (if any) from work site to Store Center, Nawada, Budaun approx distance upto 0-60 Km including loading & unloading.

A.B. Cable Scrap

Iron Scrap

STP Pole Scrap

ACSR Weasel Conductor Scrap

M/S TIWARI TRADING COMPANY (BID ID -4791535)

M/S RAHAT & BROTHERS ELECTRICALS (BID ID -4775231)