SPL REPAIR OF STREET LIGHT FITTINGS INCLUDING CONNECTED WORKS AT SUKNA AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN UNDER GE SUKNA

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft/ Loose soil complete all as specified and directed.

Excavation over areas not exceeding 1.5 M deep and getting out in Soft/ Loose Soil complete all as specified and directed.

Excavation over areas exceeding 1.5 M and not exceeding 3 M deep and getting out in Soft/ Loose Soil complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / disintegrated soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Earth filling under floors incl spreading, leveling in layers n.exc 25cm thick including well ramming and watering as reqd complete all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for sand coushioning to UG cables (8cm deep before laying of cables and 15 cm over the cable) including spreading, levelling, well ramming in layers complete all as specified and directed. NOTE:- punned thickness of 18cm only will be considered for measurement and payment.

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point complete all as specified and directed.

M&L loose filling with broken brick aggregates of gauge 80 to 150 mm in soakage pits, soakage wells, sunken portion of slab etc using broken bricks complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, similar bands, plinth coarses, string coarses, lacing coarces, parapets nad railings upto 60 cm in height, filling in pressed steel door complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for Precast Reinforced cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for Manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed.

M&L for Reinforced Cement Concrete Type B-1 1:2:4 Nominal mix (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for providing Reinforced cement concrete (1:1.5:3) type A-1 Nominal Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately.)

M&L for RCC M-25 (Design Mix) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc basement slabs reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) as in chajjas complete all as specified and directed including necessary formwork rounded or chamfered on edges complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) using 20 mm graded stone as in beams, cantilevers, bressummers, lintels over 1.5m clear span complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) using 20 mm graded stone as in columns, pillars, piers, posts and struts complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks in one brick thick honey-comb wall built in cement mortar 1:4 complete all as specified and directed.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed .

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished surfaces of concrete, flat / curved complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

S&F 40 mm thick factory made flush door shutter solid core construction , with particle board core and plywood face panels,commercial type on both side complete all as specied and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 10 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof and including dismantling complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges with screws complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F 150 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed.

S&F 75 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Hasp and staple 100 mm safety type mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screw complete all as specified and as directed.

Supply & fix as in repair 28mm dia curtain harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. with two Nos of socket ,end caps and brakets (decorative type) complete for doors/window opening all as specified and directed

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 140 mm complete all as specified and directed.

S & F Ball catches with 8 mm dia., steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S & F Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples including wooden beads complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tank and similar work confirming to Fe-290 Gde E-165 Complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm to 10 mm dia.,cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S&F Roof truss (framed) trussed, purlins,crane gantires of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1998 grade St-240 including one shop coat of zink chrome primer complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S&F steel ventilator with top hung shutter and including hinges steel peg stay complete all as specified and directed.

M&L powder coated Aluminium door, window, Cup board and ventilator shutter and frame any type (Sliding or openable ) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. ,complete all as specified and directed. Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate.

M&L decorative type plaster of paris work of size not less than 50 mm x 50 mm, as in cornice or junction of wall and ceiling complete all as specified and directed.

S&F non asbestos fibre cement building boards 4 mm thick E-Board (designer pattern) fixed or laid / inserted to GI framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including GI frame work comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with contacting clips across the intermediate channel at 457 mm centre to centre hanging from structural steel / scantling with 6 mm GI wire complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

M & L in repairs 18/19 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work in cup board shutters, partitions, shelves and similar work with teak wood beading at the edges complete all as specified and as directed.

M&L 18-20 mm thick granite slab(of any type) tiles as in platform machine cut, bedded jointed with grey/ colored cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with nosing over and including 20mm thick cement screed in 1:4 complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2 using 40mm graded agg finishing even and smooth without using extra cement as in plinth protections/path and laid fair in alternate bays & construction joints to be given at every 3m interval and corners of buildings and filling the same with bitumen and sand 1:3 complete all as specified and directed.

M&L 100 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and rough complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) in floorings including finishing the surface even and fair to receive floor finishes complete all as specified and directed.

M&L Plain cement concrete 40mm thick type B-1 (using 20mm graded aggregate) in alternate bays and finished the surface even and smooth without using extra cement complete all as specified and directed. (Glass stirps measured and paid separately).

M&L for Glass dividing strips, 38 x 3 mm thick and inserted in position to confirm to design complete all as specified and directed.

M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing with cm 1:3 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm in cement mortar 1:4 complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L Rendering 15 mm thick on other than fair faces of brick work or concrete sur-faces in cement mortar 1:4 for finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:3 on ceiling or chajja finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated ceiling surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L for prepration of new plastered ceiling surfaces and applying two coat of oil emulsion distemper over a coat of primer over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint complete all as specified and directed.

S&F 4.8 mm thick glass including tinted/dark film n.exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S&F 4.8 mm thick glass including tinted/dark film exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S & F 3 mm thick Frosted glass, ordinary type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane fixed to steel frame including steel pin complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

M&L in repairs High dencity polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.40 mm bore pipe complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S & F 15 mm bore bib tap chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 15 mm bore bib tap, two way, fancy type chromium plated, cast copper alloy, with crutch or butterfly handle and wall flange, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed.

S&F 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for hot water supply complete all as specified and directed.

M&L for 75 mm dia, type B-1, 1:2:4 cast iron floor/nahani trap with grating including jointing to waste pipe fixed in cement concrete complete all as specified and directed

M&L for 100 mm dia, type B-1, 1:2:4 cast iron floor/nahani trap with grating including jointing to waste pipe fixed in cement concrete complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S & F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore pipe complete all as specified and directed.

M & L 150 mm dia Salt Glazed stoneware Grade ‘A’ drain pipes laid in trenches and jointed in CM 1:1 complete all as specified and directed.

S&F in repairs CP Sensor faucet for wash basin (battery operated) complete all as specified and directed.

S&F in repairs CP Sensor flushing valve for urinal with complete kit (battery operated) complete all as specified and directed.

S&F in repairs 900 mm x 450 mm curved shaped urinal partition with frosted glass size 8mm to 10mm with chrome finish complete all as specified and directed.

S&F Urinal (back inlet with fixing accessories size 340x 325x 650mm, complete all as specified and directed.

S&F in repairs EWC Rimless single piece WC with UF Soft close seat cover, hinges, dual flush cistern fitting, fixing accessories and accessories set size 360 x 675 x 750mm complete all as specified and directed.

S&F in repairs wash hand basin counter Top basin size 705 x 460 x 195 mm ALS WHT 85601 complete all as specified and directed.

S&F in repairs stainless steel towel rail 600mm AQN - 7711 complete all as specified and directed.

S&F in repairs 600 mm stainless steel towel rack with lower hanger cat pat No - AKP-35781PS complete all as specified and directed.

S&F in repairs soap dispenser with glass bottle cat part No CAN - 1135 N complete all as specified and directed.

S&F in repairs Soap dish holder Cat Part No CAN - 1131N Complete all as specified and directed.

S&F in repairs Towel ring square with round flange Cat Part No CAN - 1121N complete all as specified and directed.

S&F in repairs Towel roll holder with stainless steel flap Cat Part No CAN - 1153S complete all as specified and directed.

S&F in repairs Tumbler holder Cat Part No AKP-35741P complete all as specified and directed.

S&F in repairs Double coat hook Cat part No AKP -35761P complete all as specified and directed.

S&F in repairs Hand shower (health faucet) with 8mm dia, 1.2m long fexible tube & wall hook cat part No ALD -573 complete all as specified and directed.

S&F PVC Connections pipe 450 mm long braided hose with two 15mm nuts & rubber washers without nipple cat part No - ALD 805B complete all as specified and directed.

S&F PVC Connections pipe 450 mm long braided hose with two nuts & rubber washers (suitable for basin mixers) cat part No - ALD 803B complete all as specified and directed.

S&F PVC Connections pipe 600 mm long braided hose with two nuts & rubber washers (suitable for basin mixers) Cat part No - ALD 801B complete all as specified and directed.

Dismantling 75/100 mm dia CI pipes including tee, branch piece, bend at any position (wall or laid in trench) complete all as specified and directed.

M&L CI Sand cast pipe 100 mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and directed.

M&L CI Sand cast pipe 75 mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and directed.

S&F CI Branch piece 100mm bore, double (eaqual or unequal), with parallel branches and fitted with oval access door complete all as specified and directed.

S&F CI Branch piece 75mm bore, single (equal or unequal), ordinary or inverted spigot or socketted type with parallel branches and fitted with oval access door complete all as specified and directed.

S&F CI Bands 75 mm bore with oval access door complete all as specified and directed.

S&F CI Bands 100 mm bore with oval access door complete all as specified and directed.

S&F CI Cowls 75 mm complete all as specified and directed.

S&F CI Cowls 100 mm complete all as specified and directed.

S&F vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F vitreous china (white) flat back urinal half stall type (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and directed.

S&F vitreous china wash basin white flat back size 550 x 400 mm excluding taps waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

S&F PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F Health faucet (ABS body) of CP 15mm bore fancy type and with 1.25 mtr long easy flex tube in chrome finish and wall hook including CP nipple with socket complete all as specfied and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No. 157.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 157.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on same board.

All as per item No. 157.00 here-in-before but one 3 pin socket outlet / 15 amps on the independent board with other switches, with cables 2.5 sqmm size complete all as specified and directed

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE :- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp , 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB ,SPN DB, 04 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

M &L of Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sqmm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost complete all as specified and directed.

M&L earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick buried directly in ground in vertical position (earth pit not less than 2.25 m deep below the normal ground level) with top edge of the earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead of GI strip 32x6 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, all as shown in electrical plate No. 3 connected to earthing test point and including dismantling complete all as specified and directed. Note:- The unit rate shall also include for earth work in any type of soil, PCC 1:3:6 type C1 chamber, RCC 1:1.5:3, type A1 cover slab, 50 mm thick reinforced with 8 mm dia TMT bar @ 140 mm C/C both ways, 10 mm dia plain bar lifting handle embedded in cover slab, 20 mm bore medium grade GI watering pipe, 15 mm bore GI light grade earth lead protection pipe, funnel, wire mesh, copper lugs, charcoal and common salt in alternate layer etc.

S&F Exhaust fan 250 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed.

S & F LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF =0.95, total System Lumens not less than 1100 lm, 6500k CRI = 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed.

S & F Surface and wall mounted LED batten 20 watt 4ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.90, Efficiency not less than 110 lm/W color temp 6500k CRI = 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing in repair for 25 Watt LED Street light / Road light Luminaire type of energy saving long life LED street light made up of pressure die cast aluminium housing with modular lens having IP-66 with sensor complete with connections fittings and including connecting with twin core 2.5 sqmm weather proof aluminium conductor cable complete all as specified and directed .

Supply and fixing in repair for 45 Watt LED Street light / Road light Luminaire type of energy saving long life LED street light made up of pressure die cast aluminium housing with modular lens having IP-66 with sensor complete with connections fittings and including connecting with twin core 2.5 sqmm weather proof aluminium conductor cable complete all as specified and directed .

Supply and fixing in repair for 45 Watt LED Street light / Road light Luminaire type of energy saving long life made up of pressure die cast aluminium housing with toughened glass with IP-66 with connections fittings and including connecting with twin core 2.5 sqmm weather proof aluminium conductor cable complete all as specified and directed .

Supply and fixing in repair for 90 Watt LED Street light / Road light Luminaire of energy saving long life made up of pressure die cast aluminium housing with toughened glass with IP-66 with connections fittings and including connecting with twin core 2.5 sqmm weather proof aluminium conductor cable complete all as specified and directed .

S&F of 6 KW three phase automatic street light control panel with and including astronomical switch for automatic operation on/ off street light as per set time through programmable 24 hrs switch , 32 A TP Power contactor, 40 A TPN MCB wall /floor moutable, IP 54 enclosure made out of CRCA sheet duly powder coated conforming to IS/IEC 61439 & 60529 in built short circuit protection ,Class H insulation,FRLS internal wiring,extended wide band coil and locking arrangement with padlock and panel lock complete all as specified and directed.

Supply and fix sub class 'B' bricks of standard size for cable protection laid flat across the cable in trenches complete all as specified and directed.

Supply and fixing of GI tubing light grade 40mm dia for protection of cable on pole , under road crossing or across drain , along electric pole or floor / wall complete all as specified and directed.

S&F in repairs street light junction box IP 66/69 weather proof for outdoor installation black colour having size 155 x 210 x 92 mm with terminals having two knockouts for cable entries from rear side, proctection against rain water, temperature resistant and impact resistence also comprising external bracket for fixing on pole complete all as specified and directed.

Supply, laying testing and commissoning of cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) LT Cable with stranded aluminium conductor 1100 volts grade of size 10 sqmm 2 core complete all as specified and directed.

Supply, laying testing and commissoning in replacement of cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) LT Cable with stranded aluminium conductor 1100 volts grade of size 25 sqmm 3.50 core including taking down old unsv complete all as specified and directed.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F geyser of capacity 25 Litres, 230V, 50Hz, vertical, wall mounted type, BEE 5 star rated, ABS outer body, copper inner tank with vitreous enamel coated, incoloy glass coated heating element, adjustable thermostat for temperature regulation, multifunctional safety valve with & including 3 core copper cable of 1 to 2 metre length with 3-pin plug of 16A capacity, fixing arrangement such as. bracket, nuts, bolts washers etc. complete all as specified and directed.

S&F Sheet metal enclosures with socket single pole and neutral enclosures with a 2 pin and earth plug and socket complete with one single pole MCB's of 10 Amps complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repair street light brackets made out of GI tubing, light grade, 40mm bore 1200 mm long bent to shape at 120 degree, fixed on pole by providing MS clamp made up of flat iron 50 x 6 mm including bolts nuts and washer of suitable size complete all as specified and directed

SHRI N.DAS (BID ID -3455556)

MS ORIENT ENGINEERING WORKS (BID ID -3454739)

R N SAH N CO (BID ID -3454797)

M/s TRIMURTI ASSOCIATE (BID ID -3456416)

Jagatbandhu Enterprises (BID ID -3455603)

M/S GLORIOUS CONSTRUCTION (BID ID -3456001)

Janata Enterprises (BID ID -3455462)

G C DUTTA N CO (BID ID -3456210)