SPL REPAIR TO BLDG NO P03 OF 172 MH AT TIBRI MIL STN UNDER GE GURDASPUR

Material and Labour for rendering 12 millimeter thick ready-mix mortar of approved makes on brick or concrete ceiling surface, providing a finished surface that is even and fair up to a height of 12 meter. This work includes the taking down and removal of existing cement plaster of any description, complete all as specified and as directed.

Material and Labour for rendering 5 millimeter thick ready-mix mortar of approved makes on brick or concrete ceiling surface, providing a finished surface that is even and fair up to a height of 12 meter. This work includes the taking down and removal of existing cement plaster of any description, complete all as specified and as directed.

Material and Labour for rendering 15 millimeter thick ready-mix mortar of approved makes on brick or concrete surfaces of walls, providing a finished surface that is even and fair up to a height of 12 meter. This work includes the taking down and removal of existing cement plaster of any description, complete all as specified and as directed.

Material and Labour for preparation of new plastered surfaces of walls by brooming down, making good holes, cracks, et cetera, and Material and Labour for applying two or more coats of 100% Premium acrylic emulsion paint having Volatile Organic Compounds (VOC) less than 50 gram per litre and UV resistance as per Indian Standard 15489:2004. This includes alkali and fungal resistance, and dirt resistance exterior paint of the required shade (Company Depot Tinted) with silicon additives at the rate of 1.43 litre per 10 Square Meter, applied over and including a priming coat of exterior primer applied at the rate of 0.90 litre per 10 Square Meter over new surfaces, all as specified and as directed.

Material and Labour for preparation of new plastered surfaces of the ceiling by brooming down, making good holes, cracks, et cetera, and Material and Labour for applying three coats of white wash, complete all as specified and as directed.

Preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade on walls, applied over a priming coat of chalk whiting on the plastered surfaces, complete all as specified and as directed.

Material and Labour for preparation of old plastered surfaces of walls by brooming down, making good holes, cracks, et cetera, and Material and Labour for applying two or more coats of 100% Premium acrylic emulsion paint having Volatile Organic Compounds (VOC) less than 50 gram per litre and UV resistance as per Indian Standard 15489:2004. This includes alkali and fungal resistance, and dirt resistance exterior paint of the required shade (Company Depot Tinted) with silicon additives at the rate of 1.43 litre per 10 Square Meter, applied over and including a priming coat of exterior primer applied at the rate of 0.90 litre per 10 Square Meter over new surfaces, all as specified and as directed.

Material and Labour for preparing old plastered or unplastered surfaces of the ceiling and applying one coat of white wash, complete all as specified and as directed.

Material and Labour for preparing old plastered or unplastered surfaces of walls, including cornices, and applying one coat of distemper oil emulsion paint, white or tinted, complete all as specified and as directed.

Material and Labour for preparation of new wooden surface exceeding 10 centimeter width or girth, and applying two coats of synthetic enamel paint over one coat of primer, complete all as specified and as directed.

RUNNING METER

KILOGRAMS

Supplying and Fixing pressed steel frames 1.25 millimeter thick for door frame size 105 millimeter by 60 millimeter with one or more rebates. This includes necessary fixing lugs, hinges, lock strike plate, filling of chowkats with Plain Cement Concrete (PCC) 1 part cement : 3 parts sand : 6 parts aggregate type C-1 (using 20 millimeter graded stone aggregates), filling of hold fasts, tarring to the inner surface (surface in contact with concrete or brick surface) of chowkats and hinges, and applying two coats of synthetic enamel paint to the outer surface over red oxide primer after proper preparation of surfaces, complete all as specified and as directed.

Supplying and Fixing 30 millimeter thick factory made Flush shutters, featuring solid core construction, with block board core and plywood face panels on both sides, complete all as specified and as directed.

Supplying and Fixing a Factory made solid panel Polyvinyl Chloride (PVC) door shutter 30 millimeter thick (style), consisting of a frame made out of Mild Steel (MS) tubes for the top and bottom rails. The Mild Steel frame shall be covered with heat moulded plain colour Polyvinyl Chloride 'C' channel having a Polyvinyl Chloride sheet strip of 20 millimeter width stuck inside with solvent cement for stiles, and plain colour Polyvinyl Chloride sheets for the top rail, lock rail, and bottom rail on either side and as a gap insert for the top rail and bottom rail. The panelling of plain colour Polyvinyl Chloride sheet shall be fitted in the Mild Steel frame, welded or sealed to the stiles and rails with suitable Polyvinyl Chloride sheet beading, and joined together with solvent cement. This includes supplying and fixing in the frame at site as per specification and drawing, complete all as specified and as directed.

Supplying and Fixing Mild Steel framed work, such as door frames or chowkats or gates, made of angle or other sections, including gusset plates, rails, braces, et cetera, and similar work. This includes primer conforming to Grade E 250 quality A, complete all as specified and as directed.

Supplying and Fixing Galvanized mild steel wire cloth, 0.63 millimeter nominal diameter of wire and average width of aperture 1.40 millimeter, and fixed with tinned tacks or galvanized wire staples, complete all as specified and as directed.

Supplying and Fixing Aluminium anodized barrel tower bolt of extruded section 150 millimeter long, Indian Standards Institution marked, complete all as specified and as directed.

Supplying and Fixing extruded aluminium alloy handle, fabricated type, anodized, of size 150 millimeter long, complete all as specified and as directed.

Supplying and Fixing 100 millimeter size butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized and fixed, type B-21, through bolt or with screw, complete all as specified and as directed.

Supplying and fixing in repair a curtain rod 20 millimeter diameter of Mild Steel with Polyvinyl Chloride Coated finish, including fixing brackets, stops, rollers, et cetera, fixed to the wall with screws and Polyvinyl Chloride plug, including taking down the existing curtain rod, complete all as specified and as directed.

Material and Labour for waterproofing treatment to sunken floors with the application of a two-component acrylic modified cementitious coating, incorporating a glass fabric sheet between coats (using approved materials such as SIKA Top seal-107 / Brush Bond FOSROC / Dr Fixit / STP / CICO). The application must be done on a dried surface free from contaminants such as dirt, dust, oil, surface treatments, and old coating. Concrete substrates must be prepared mechanically using abrasive blast cleaning or milling to remove cement laitance and existing coating, and achieve a gripping, clean, dry, and laitance-free profile. The installation instructions of the Manufacturers shall be followed strictly. Note: (a) Any visible cracks must be chipped out, cleaned, and filled with SIKA latex SBR 100 Putty / Dr Fixit 302 SBR latex / Perma latex SBR / FOSROC Nitobond SBR latex / Asian Paint latex in a "V" groove pattern, and the surface finally cleaned with a powder grinder, wire brush, and vacuum pressure. (b) The waterproofing coating should be taken up to a height of 450 millimeter above the Finished Floor Level (FFL) on vertical surfaces. (c) The second coat shall be applied 6 to 8 hours after the application of the previous coat and in the right-angle direction. (d) All traps in sunken slabs must be enclosed with Plain Cement Concrete (PCC) 1 part cement : 1.5 parts sand : 3 parts aggregate (Minimum 150 millimeter) all around. Complete all as specified and as directed.

Material and Labour for removing existing treatment, including all loose gravel, cement mortar, dirt, oil, grease, and foreign material using a jet of dry air. This involves roughening and cleaning the surface mechanically or by grinding to make it smooth before application. Removing loose existing bituminous material manually and with a heat torch gun to obtain a smooth, plain finished surface free from loose material. Repairing all joints and cracks, and applying a primer (such as Smart Care epoxy primer) to seal the pores and cracks and enhance the adhesion of the coating. Applying a first coat of fibre-reinforced elastomeric liquid waterproofing membrane formulated with Polyurethane (PU) hybrid polymers and reinforcing acrylic fibres, featuring a Sun Reflective Index (SRI) of 100-110, having a mi

Material and Labour for Plain Cement Concrete (PCC) 1 part cement : 2 parts sand : 4 parts aggregate type B-0, using 12.50 millimeter graded stone aggregate as in roof padding, averaging a thickness of 50 millimeter, complete all as specified and as directed.

Material and Labour for Plain Cement Concrete (PCC) 1 part cement : 5 parts sand : 10 parts aggregate type E2 using 40 millimeter graded stone aggregate as in filling, foundation, and mass concrete in sunken floor, complete all as specified and as directed.

Material and Labour for 25 millimeter thick Cement Concrete 1:2:4 type B-0 (using 12.5 millimeter graded stone aggregate) as in sub base for receiving the floor finishes, complete all as specified and as directed.

Supplying and Fixing non-skid, coloured ceramic tiles, 7 to 8 millimeter thick, joint-free (square or rectangular), where the area of each tile exceeds 0.11 Square Meter but does not exceed 0.18 Square Meter, for floors et cetera. The tiles shall be set and jointed in neat cement slurry and pointed in white cement or coloured cement to match. This includes 15 millimeter thick screed bed in Cement Mortar 1:6, and dismantling of the existing tile floor and screed, complete all as specified and as directed.

Material and Labour for ceramic glazed coloured tiles of size 350 millimeter by 250 millimeter by 7 millimeter or 450 millimeter by 300 millimeter by 7 millimeter thick, joint-free, applied on and including a 10 millimeter thick screed bed in Cement Mortar 1:4. The tiles shall be set and jointed in neat cement slurry and pointed in coloured cement mixed with pigment to match the colour of the tiles on vertical surfaces of the wall, such as in skirting or dado. This includes dismantling of existing tile floor and screed, complete all as specified and as directed.

Supplying and Fixing in repair Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down for high pressure, with or without lettering 'Hot' or 'Cold', with long screwed shanks and fly-nuts, screwed for iron pipe 15 millimeter bore and fixed, complete all as specified and as directed.

Fixing only Galvanized Iron tubing 15 millimeter bore, medium grade, fixed to wall, ceiling, or floor et cetera. This includes cleaning and re-using old serviceable pipe and supplying new fittings, Indian Standards Institution marked, complete all as specified and as directed.

Fixing only Galvanized Iron tubing 20 millimeter bore, medium grade, fixed to wall, ceiling, or floor et cetera. This includes cleaning and re-using old serviceable pipe and supplying new fittings, Indian Standards Institution marked, complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving not exceeding 15 centimeter thickness (below or above ground level), including disposing of the resulting rubbish to a distance exceeding 50 Meter but not exceeding 100 Meter away to low lying areas, complete all as specified and as directed.

Material and Labour for 40 millimeter thick Plain Cement Concrete (PCC) 1 part cement : 2 parts sand : 4 parts aggregate type B-1 (using 20 millimeter graded stone aggregate) as in floor finishing, providing an even and smooth finish without using extra cement, complete all as specified and as directed.

Material and Labour for 50 millimeter thick Plain Cement Concrete (PCC) 1 part cement : 2 parts sand : 4 parts aggregate type B-1 (using 20 millimeter graded stone aggregate) as in plinth protection, providing a finish that is fair and even, complete all as specified and as directed.

Material and Labour for Plain Cement Concrete (PCC) 1 part cement : 4 parts sand : 8 parts aggregate type D-2 in foundations, such as sub base, filling, and mass concrete (using 40 millimeter graded stone aggregate) to raise the level, complete all as specified and as directed.

Material and Labour for Green Marble work 18 to 20 millimeter thick (table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms, staircase and similar locations, set in Cement Mortar 1:4. This work includes pointing in white cement 1:2 using marble dust with admixture of pigment to match the marble shade, including 15 millimeter thick screed bed in Cement Mortar 1:4 and dismantling of existing marble, complete all as specified and as directed.

Use and waste of formwork for Chullah hoods, shelves, chajjas, weather shades, corbels, water troughs, and similar items, including the edges of rough finished flat concrete surfaces, complete all as specified and as directed.

Supplying and Fixing in repair kitchen sinks made of stainless steel 1 millimeter thick with plugs, washers, wastes, and coupling. This includes bedding in cement mortar onto a dwarf wall or including fixing cantilever brackets and connecting union to pipe. The overall size is 495 millimeter by 420 millimeter, and the bowl size is 410 millimeter by 330 millimeter by 160 millimeter, including fittings arrangement, complete all as specified and as directed.

PER 1000 NOS

Supplying and Fixing a steel window (box type) made of Electric Resistance Welded (ERW) tube hollow P-section of size 60 millimeter by 25 millimeter, featuring a double rebated outer frame comprising double shutters (gauged skeleton and glazed shutters). The shutter frame is made of Electric Resistance Welded tube P-section size 50 millimeter by 20 millimeter with two openable leaves for each shutter, consisting of two Numbers sash bars of T-section 20 millimeter by 3 millimeter welded to the frame, and one vertical mullion of Electric Resistance Welded box type T-section of size 60 millimeter by 25 millimeter and Flat Iron 2 millimeter thick welded or screwed to the frame for fixing the wire gauge. This includes Mild Steel guard bars, fittings, and fixtures welded to the frame or shutters as detailed below and as shown on Drawing Number CEJZ/TD-1020/08 Sheets 1/3 to 3/3, complete including two coats of painting and taking down the unserviceable window: (i) Hold fasts, 150 millimeter long, made of Flat Iron 12 millimeter by 3 millimeter 04 Numbers per window; (ii) Handle of Z-section 20 millimeter by 25 millimeter, 100 millimeter long 01 Number per leaf; (iii) Mild Steel Tower bolt 150 millimeter long 02 Numbers per leaf; (iv) Z-section 20 millimeter by 25 millimeter, 100 millimeter long stopper 01 Number per leaf;

(v) Cleat 55 millimeter long of hollow square 15 millimeter by 12 millimeter 02 Numbers per leaf; (vi) Mild Steel pintle hinges size 75 millimeter by 12 millimeter 2 Numbers per leaf; (vii) Making good dismantled portion in Plain Cement Concrete (PCC) 1:2:4 type B-1 for hold fasts (four Numbers for each window); (viii) Painting with one shop coat of zinc chromate primer. Note: Wire cloth and glass shall be measured and paid for separately. Complete all as specified and as directed.

Supplying and Fixing point wiring using PVC insulated and PVC unsheathed multi-stranded Fire Retardant Low Smoke Halogen (FRLSH) copper conductor cable of size 1.5 Square millimeter. This work includes installation in concealed PVC conduit fittings, making good all disturbed surfaces, and providing continuous copper earth wire of 1.5 Square millimeter cross-section connected to the common earth system. Including the provision of a 3 millimeter thick plastic laminated sheet of appropriate size and fixing it to Cast Iron or Mild Steel boxes for mounting accessories such as switches, surface sockets, and regulators, complete. The item covers: (a) One light, fan, or bell point control

led by a single one-way switch, as specified and as directed.

Supplying and Fixing 3 pin socket outlet, rated at 5 Amperes, flush type, as specified and as directed.

Supplying and Fixing switch, flush type, rated at 15 Amperes, single pole, one way, as specified and as directed.

Supplying and Fixing 3 pin socket outlet, rated at 15 Amperes, flush type, as specified and as directed.

Supplying and Fixing piano switch, 2 way, rated at 5 Amperes, as specified and as directed.

Supplying and Fixing a replacement LED tube light fitting suitable for all-purpose surface and wall mounting. The fitting shall be a polycarbonate LED batten with single-side connection, aluminium housing, and an integrated electronic driver of 20 Watt capacity (four feet length). Including connection with Polyvinyl Chloride (PVC) insulated twin core 23/0.0076 twisted copper cable from the ceiling rose to the tube light fitting, complete, as specified and as directed.

Supplying and Fixing in replacement of an electronic step-type fan regulator, rated at 100 Watt, 240 Volt. Including connection, complete, as specified and as directed.

Supplying and Fixing lamp holder, Polyvinyl Chloride (PVC) body, angle type. Including a 9 Watt Light Emitting Diode (LED) bulb with a polycarbonate body, complete, as specified and as directed.

CUBIC METER

Material and Labour for supplying and fixing ceiling rose, surface mounted, made of bakelite, 65 millimeter by 50 millimeter in size, with three terminals, as specified and as directed.

Supplying and Fixing in replacement a Galvanized Iron (GI) pipe bracket, made out of light grade Galvanized Iron (GI) pipe of 32 millimeter diameter and bent to shape (1.5 Meter long). Including Mild Steel (MS) clamps made out of Mild Steel (MS) flat iron of size 32 millimeter thick, complete with nuts, bolts, and washers. This work includes dismantling the existing Galvanized Iron (GI) pipe bracket and drilling of holes for nuts and bolts, et cetera, as specified and as directed.

Supplying and Fixing Light Emitting Diode (LED) street light fitting, rated at 35 Watt, 230 Volt Alternating Current (AC), outdoor type. The fitting features high pressure die cast aluminium housing, heat resistance, and is complete with a driver, lamp bracket with impact and corrosion resistance, including thermal management in multiple optics, and complete Ingress Protection 65/66, as specified and as directed.

Supplying and Fixing in repair Miniature Circuit Breaker, single pole, rated from 6 Amperes to 32 Amperes, complete, as specified and as directed.

Supplying and Fixing in repair Miniature Circuit Breaker, single pole and neutral (SPN) type, rated from 40 Amperes to 63 Amperes series, complete, as specified and as directed.

Material and Labour for replacement of a Distribution Board (DB) made out of Cold Rolled Cold Annealed (CRCA) sheet, vertical type, double door, Triple Pole and Neutral (TPN), 4 Way, Mild Steel (MS) sheet. Including fixing the board in the wall, cutting chases, grouting, necessary patch work, and white wash to match the existing finish, including making all electrical connections, as specified and as directed. The Distribution Board contains the following components (Note: All connections of incoming and outgoing wires in the Moulded Case Circuit Breaker (MCCB) and Miniature Circuit Breaker (MCB) must be made using a thimble of suitable size, as specified and as directed): (a) Moulded Case Circuit Breaker (MCCB) 4 Pole, 63 Amperes, 16 Kilo Amperes breaking capacity with thermal release - 1 Number (Incoming). (b) Bus bar 200 Amperes rated, made out of Aluminium, duly insulated and covered with wire adhesive tape (Red, Yellow, Blue, and Black) - 4 Numbers. (c) Miniature Circuit Breakers (MCB) Single Pole and Neutral (SPN) 40 Amperes - 4 Numbers, and Miniature Circuit Breakers (MCB) Single Pole (SP) 40 Amperes - 4 Numbers (Outgoing). (d) Connection from the Moulded Case Circuit Breaker (MCCB) to the bus bar will be made with an Aluminium Strip of suitable size, as specified and as directed.

Material and Labour for complete earthing, including supplying and fixing a Galvanized steel earth plate electrode, 60 centimeter by 60 centimeter by 6 millimeter thick, buried directly in the ground (earth pit not less than 2.25 Meters deep below ground level) with the top edge of the plate not less than 1.5 Meters below normal ground level. The plate is connected to a Galvanized Iron earth lead wire of 4.0 millimeter diameter by means of Galvanized Iron or steel bolts, nuts, check nuts, and washers, all as shown in electrical plate Number 3, and connected to the earthing test point. Including testing upon completion, providing a watering funnel and wire mesh, and the protection system consisting of a 20 millimeter bore medium grade Galvanized Iron pipe (for watering) and a 15 millimeter bore light grade Galvanized Iron pipe for protection of the earth lead. The work includes provision of a concrete pit in Plain Cement Concrete (1:3:6) Type C1, and a pre-cast Reinforced Cement Concrete (1:2.4) Type B1 cover slab, 54 centimeter by 54 centimeter by 5 centimeter, including 8 millimeter diameter Thermo Mechanically Treated (TMT) bars both ways at 15 centimeter center to center, with one lifting handle made out of an 8 millimeter diameter Mild Steel bar. All necessary excavation and earth work in any type of soil is included, complete with dismantling the existing system, as specified and as directed.

Supplying, laying, and testing electric power cables, Cross-linked Polyethylene (XLPE) insulated, screened, Polyvinyl Chloride (PVC) bedded, galvanized steel strip or wire armoured (heavy duty), 1100 Volt grade, with stranded aluminium conductor of size 50 square millimeter, 3.5 core.

Excavation in trenches in soft loose soil, including cutting road surfaces, for poles, stays, cables, pipes, and similar items. The excavation width shall not exceed 1.5 meter and the depth shall not exceed 1.5 meter, including getting out all excavated material, as specified and as directed.

Returning filling, including spreading and well ramming in layers, each layer not exceeding 25 centimeter thick, in soft loose soil, as specified and as directed.