Construction i/c Metalling and Blacktopping of a road from Kyrdem to Khyndewsoo (Khyndewso) (10.00 Km) (MG/04/III/03/04) Upgradation using FDR Technology

Amount

Cutting of branches of trees shrubs and trimming of grass and weeds

iii) Trimming of grass and weeds from the shoulders/berms and disposing off the same to suitable locations as per technical specifications Clause 1914

Earthwork in Hill Road

Excavation in Hilly Areas in Soil by mechanical means A.Excavation in soil in Hilly Area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth with a lift upto 1.5 m and a lead upto 20 m as per Technical Specification Clause 1603.1

Full Depth Recycling asphalt/granular pavement Stabilization of in-situ (existing pavement crust) or soil or otherwise sub base/ base course up to the required depth by cold in-situ recycling using cement and chemical additives / otherwise: Providing pulverizing, spreading, milling and mixing of chemical additives at the appropriate rate as per job mix design in accordance with IRC-SP-72-2015 , IRC-37-2012 & 2018 and IRC SP 89 (part II) 2018. Cementitious additive @ rate of minimum 5 - 7% and CCS/CS additive should be spread on the existing pavement using a mobile truck mounted containe-rized cement/ additive spreader with micro processor controlled weighing and spreading system. The additive spreader shall have variable working width sufficient to cover whole pavement lane. The in-situ stabilization process shall be carried out by a mobile and self propelled stabilizer / reclaimer of working width of 2.4 m and with minimum engine horse power of 440 kw with a variable working depth up to 50 cm.

The resultant stabilized mix then would be profiled to the required grade, level and thickness using motor grader and the mix would be compacted using 20 tonne pad foot roller in combination with smooth wheel roller to achieve desired proctor density as per IRC 37-2012 & 2018 and complete in all respect and curing with water as required including all materials, labour and machinery etc. The entire in-situ process would be carried out in single pass with milling and pulverising of damaged asphalt pavement / soil/ aggregates / soil-aggregate mixture to the desired depth and with simultaneous addition of additives and water with machine integrated spray bars fited on the wheeled self-propelled and vibratory pad foot roller to achieve the desired proctor density in all respects. The tandem roller be followed by Pneumatic Tyre Roller. The minimum unconfined compressive strength (UCS) of stabilized sub base/ base should be 4.5 to 7 MPa after 7 / 28

days of curing as per IRC-SP-72-2015 , IRC-37-2012 & 2018 . Also durability aspects (wet-dry cycles) of stabilized sub base should be satisfied as per IRC 37-2012 & 2018 and IRC SP 89 (part II) 2018. The gradation mixes and materials should be as per IRC 37-2012 & 2018 and IRC SP 89 (part II) 2018. The train of equipments to be used are binder spreader- water Tanker- Additive Truck- Recycler- Padfoot Roller (20 Tonne) + Single Drum Compactor- Grader- Tandom Roller- Pneumatic Tyre Roller (20 Tonne) [ Min thickness of FDR shall not be less than the thickness mentioned in DPR, However FDR Thickness will be based on Design Mix ] [RA-6] 1.Additional Materials

2.Full Depth Reclaimation

Prime coat

(III) Providing and applying tack coat with bitumen emultion (RS-1) Using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface treasted with primer & cleaned with hydraulic broom as per technical specification clause 503.

Tack coat

(III) Providing and applying tack coat with bitumen emultion (RS-1) Using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface treasted with primer & cleaned with hydraulic broom as per technical specification clause 503.

Mix Seal Surfacing

Providing, laying and rolling of close-graded premix surfacing material of 25 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509 By Mechanical Means Type B (I) Bitumen (S-90)

TRAFFIC SIGN AND ROAD FURNITURE Trafic - Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminum sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801

(ii) 600mm equilateral triangle

(iii) 600mm circular

(vii) 900mm side octagon

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

5th Kilometer Stone

Ordinary Kilometer Stone (precast)

200 m Stone (precast)

Guide posts

Construction of RCC guide posts of 250 mm dia M15 grade cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC posts not to exceed 1 in 500 as per drawing and Technical Specification Clause 1608.2 (Rates as per Annexure A-7)

Painting lines, Dashes, Arrows, etc. on Road in Two Coats on New Work Painting lines, dashes, arrows, etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification Clause 1702

Centre Lines and Edge Lines

Speed Breaker

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting,1.5mm thick spported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm, 600mm below ground level as per drawings and Technical Specification Clause 801 ii. 600 mm Equilateral Triangle.

Providing and Fixing 'Logo' of PMGSY Project Providing and fixing of typical PMGSY informatory signboard with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flatiron 25mmx5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm. The angle iron frame of the lower most plate and flatiron frame of middle plate will be welded to 2nos.75mmx75mmof12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mmx450mmx 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mmof12SWG steel plate tube. All M.S. will be stove name led on both sides. Lettering and printing arrows, border etc. Will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed post sand steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause1701.2.3, fixed over aluminium sheeting, 2mm thick with area not exceeding 0.9 sqm supported on 2 inch dia GI Pipe firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450x450x600mm, 600mm below ground level as per approved drawing and Tehnical Specification Clause 1701

Providing and Fixing "Maintenance Information Board" Providing and fixing typical PMGSY Informatory signboard with Logo as per MORD specifications and drawing. One single MS plate of 1.6 mm thick welded with MS angle iron frame of 25mm x 25mm x 5 mm will be welded with

Protection Work (Retaining Wall)

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side (I) Ordinary Soil Upto 3 m depth Wall Footing

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 A. With crushed Stone Nominal mix 1:3:6 Below Footing

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 12 II.Coursed rubble masonry (2nd sort).In 1:4 cement mortar

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 12 II.Coursed rubble masonry (2nd sort).In 1:4 cement mortar Parapet Wall

PCC DRAIN WITH RCC COVER

Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I) Ordinary Soil Upto 3 m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 I. P.C.C grade M 10 Nominal mix 1:3:6 Drain Bottom

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 III. P.C.C. grade M 20 (i) Nominal mix (1:2:4)

Drain Side Walls

Drain Bottom

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 iv. R.C.C grade M 20

Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202 10 mm Tor

Lined Drain (L=100.00 Rm)

Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I) Ordinary Soil Upto 3 m depth

Providing and laying of dry rubble flooring complete as per drawings and technical specifications Clause 1303.3 Drain Bottom

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 III. P.C.C. grade M 20(i) Nominal mix (1:2:4)

Drain Side Walls

Drain Bottom

UNLINED DRAIN

Cross Drainage Work New Proposal Hume Pipe Culvert (10 Nos)

Excavation for Structures Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. I. Ordinary soil Upto 3 m depth

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling course below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Bedding for pipe II. Type B (First Class) Bedding Laying (First Class) bedding on well compacted sand, Moorum or approved granular material as per Clause 1105 (ii)

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in Single Row Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia

Stone Masonry Work in cement mortar in foundation of Head walls complete as per drawing and technical specification Clause 1109 (A) In 1:4 cement mortar

Plastering with Cement Mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification

Construction of Subgrade and Earthen Shoulders Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. I. Private Land

Cross Drainage Work Repair Hume Pipe Culvert (20 Nos)

Stone Masonry Work in cement mortar in foundation of Head walls complete as per drawing and technical specification Clause 1109 (A) In 1:4 cement mortar

Plastering with Cement Mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification

Good and Service Tax (18%)

Five Years Maintenance

Maintenance for 1st Year

Maintenance for 2nd Year

Maintenance for 3rd Year

Maintenance for 4th Year

Maintenance for 5th Year