Repair/ Renovation/ Upgradation/ Improvement facelifting Electrical works in SKIMS as Detailed in SBD

Amount

Dismantlling of old existing panel on ground floor including removing of cables, circuit wires, changeover switch and UPS & fixing of the UPS . The job includes cost its re installation of Ground Floor/1st floor, as per requirement, complete job

Providing and laying of spans of 3 ½ core XLPE Al. cable Armored of various sizes as mentioned below size of 1.1KV grade

185 mm sq. 3 ½ core

300 mm sq. 3 ½ core

Providing & making of end terminations of following sizes Aluminium cables

185 mm sq. 3 ½ core

300 mm sq. 3 ½ core

Providing & fixing of fresh lighting point (5-6 amp) exposed surface with using double locked PVC channel 25x2 mm thick with accessories to be fixed on the surface of the wall with rowel plugs, saddles, screws, using multi-strand 3 x1.5 mm sq. pvc insulated copper wire (P+N+E) complete with P/F of switch 5/6 amps F/T to be fitted on 3mm Bakelite sheet suitable size,M.S/Wooden box, rowel plugs & screws etc. complete Point.

Providing & fixing of fresh lighting point (5-6 amp) recessed with using PVC Conduit meduim duty 25 mm dia with accessories using multi-strand 3 x1.5 mm sq. pvc insulated copper wire (P+N+E) complete with P/F of switch 5/6 amps F/T to be fitted on 3mm Bakelite sheet suitable size,M.S/Wooden box, rowel plugs & screws etc. complete Point.

SITC of Electric Heater / Geyser of capacities as mentioned below with following parameters . 1.Energy saving. 5 Star Certification by BEE 2. Provision of Temperature regulation by means of external Knob 3. Power Rating:- 220/ 230V, 50 Hz, Single Phase. 4. Maximum Rated Pressure.= 8 bar 5. Installation Type Vertical / Horizontal mounted as per site requirement 6. Body Type:- Rust, water proof and Shock Proof outer body with attractive looks and corrosion resistant inner tank made of cold rolled steel ,resistant to hard water. 7. Element Type:- glass coated heating element to prevent from corrosion and hard water. 8.Safety Valve maximum pressure =8 bar maximum 9. Energy efficiency feature:- Should have high density PUF insulation for energy Saving 10. Anti syphon system to prevent back flow of water. 11. Should have Indicating Lamps for ON & CUTT OFF. 12. Confirming to :IS 2082:2018 , IS 302-1, IS 302-2-21 35 Ltr.

Providing and fixing of LED 2feet long batten 6000/6500k Light having extruded aluminium body with anti-glare diffuser with energy efficient electronic driver CRI ≥ 80 with minimum sytem lumens 1000 and maximum wattage 10 , IP 20 , surge proctection 2KV or more including connection with multistrand copper conductor 3 core cable etc as required at sitewith burning hours greater than 50000 Hours.

Providing and fixing of LED 4feet long batten 6000/6500k Light having extruded aluminium body with anti-glare diffuser with energy efficient electronic driver CRI ≥ 80 with minimum sytem lumens 2000 and maximum wattage 20 , IP 20 , surge proctection 2KV or more including connection with multistrand copper conductor 3 core cable etc as required at sitewith burning hours greater than 50000 Hours.

Providing and fixing of LED 4feet long batten 6000/6500k Light having extruded aluminium body with anti-glare diffuser with energy efficient electronic driver CRI ≥ 80 with minimum sytem lumens 4000 and maximum wattage 40, IP 20 , surge proctection 2KV or more including connection with multistrand copper conductor 3 core cable etc as required at sitewith burning hours greater than 50000 Hours.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

6 Module

8 Module

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

P/f of Phenolic Laminated Sheet 3 mm thick .

Supplying and Fixing Double Locked PVC Channel 2 mm thick

Supplying and Fixing of following sizes Flexible Conduit

a) 19 mm dia

b) 25mm dia

a) 32 mm dia

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular Switches in recess etc. as required.

i) 1 or 2 Module (75mmX75mm)

ii) 3 Module (100mmX75mm)

iii) 4 Module (125mmX75mm)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface/recessed steel/ PVC conduit.

1 x 1.5 sq. mm

1 x 2.5 sq. mm

1 x 4 sq. mm

1x 6 sq. mm

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in Surface/recessed pvc conduit as required. 2x10mm+1x6mm

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including Connections etc. as required.

Supplying and fixing 14 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supply installation testing and commissioning of exhaust fans metallic Type with Bird Guard to protect fan in ruuning condition with double ball bearing & heavy motor including the cost of wall opening and making good etc complete as required 300 mm dia (Exhaust Fans)

Supply installation testing and commissioning of following sizes of plastic body exhaust fans shutter type with Heavy duty motor Rated speed = 1400 RPM . RAte voltage -220 to 240 Volts . A) 200 mm dia

Supply, Installation, testing and commissioning of 125A, 415V , 4P, indoor fixed type, single front, wall mounted, top cable entry, metal enclosed Automatic Transfer Switch (ATS) Panel with floor mounted suitable for operation at indoor site conditions with 1 no. ATS ( having two nos. of incomers) including supply of all commissioning spares, special tools and tackles & documentation, complying to Standard IEC 60947-6-1 for transfer and 60947-3 for disconnection function, shall have three distinct stable positions, the ATS shall have all the four poles fully rated and simultaneously operating. To be used between UPS & normal Supplies

Wiring for AC points with 2X4 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 Nos 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required ( 30 pts )

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in recess including cutting the wall and making good the same as required

Supply and fixing of 25mm dia medium class PVC conduit 2mm thick along with accessories like with rowel plugs ,screws ,sadlles ,bends etc complete as required at site . (in surface manner)

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve,10 KA SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required

Providing and laying Circuit wire as per site requirements using multi strand pvc insulated FRLS copper wire excluding the cost of conduit.

a) 3x 1.5 mm 2 multi strand pvc insulated copper.

b) 3x 2.5 mm2 multi strand pvc insulated copper.

c) 3x 4 mm² multi strand pvc insulated copper.

d) 4x 6mm² mm² multi strand pvc insulated copper.

e) 4x10mm² mm² multi strand pvc insulated copper.

Supplying and fixing following rating, 240/415 volts, “C”curve,10KA miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc (MCBs)

a) MCB single pole 6 A -32 A

b) MCB Double Pole 10 - 32 A

c) MCB TPN 32 A

d) MCB TPN 63A

SITC of Wall mount fans 400 mm with Plastic Body as specified below 1.Motor AC 2.Governing standard I.S.2997 (Latest) 3.Power Consumption: Approx. 100 Watts 4.Power supply Single phase AC 230V, 50Hz 5.Speed: 1200 -1400 rpm with regulator 6.Sweep: 400 mm 7.Air Flow: 72-80 m3/min. 8..motor protection through thermal 9.overload protection device 10.It should have minimum 3 levels of speed control. Features: Suitable for mounting on walls with easy mounting arrangements, Noise level shall be within limits adjustable upward and downward tilt mechanism

Supply, Installation, Testing and Commissioning of 1200 mm sweep, Ceiling fan (with Remote) with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019),THD less than 10% and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulationresistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Providing & making RCC foundation of 1300mm(H)X600mmX600mm size with 1:2:4(1Cement, 1.5 Coarse, 3 Stone aggregate) complete with 12mm dia. M.S. bar for reinforcement along with centering & shuttering i/c supplying & fixing 600mm long , 16mm dia J type G.I, coated foundation bolt/ Anchor bolt with template suitable for 6.0mtr octogonal Pole 100mm dia 600mm length corgated pipe complete with excavation the soil & refilling, ramming, curing etc. as reqd. a) 06 meter Octogonal Galvanized Pole (Foundation)

Supply & errection of flange mounted 6mtrs long hot dip galvanized Octangonal Pole of following height made from 3 mm thick HT Steel plate, having top dia-70mm & bottom dia of 130 mm complete with average coating thickness of atleast 65 micron.( Subham poles. The galvanizing shall be done in single dipping. There shall not be any circumferential welding. Pole shall have door of approximate 300 mm length at the elevation of 500 mm from the Base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connections. The door shall be flush with the exterior surface and shall have suitable locking arrangement. Pole shall have galvanized base plate of size 220 mm x 220mm x 12 mm thick with provision of holes for 4 no. 20mm dia bolt. including supplying and fixing the following in the window box provided for cable termination a) Supplying and fixing 6mm thick laminated mounted sheet inside the window mounted on and including providing and welding 02 nos G.I. strips 3mm thick of suitable length and having suitable size tapped holes as reqd. (S L Poles)

Supply fixing of galvanized pole bracket (arms) of approved design suitable for above mentioned existing a pole size completed in all respects with proper fabrication for installation of above street lighting fittings on the top of steel tubular poles. a) Single arm 1 meter long with an angle as per requirement. (Arm)

Providing, installation, testing and commissioning of LED Street light luminaire as per following specification 1. Input voltage : 150 V to 270 V 2. LDE lamp efficiency : Min 95 to 110 lumens/watt 3. Power factor : >0.90 4. Life expecting : 50,000 hours 5. No of hours usage / day : 10 to 12 hours/day 6. Rated watt : 70-80 W 7. Luminous flux : 7000 to 8000 lumens 8. Colour Temperature : 5,500 to 6500 K with test certificate 9. Ingress protection : IP 65/IP 66 10. Total harmonic distortion (THD): <15% with test certificate 11. Colour rendering index : Ra > 75 12. Working Temperature : 0 deg to 50 deg C 13. Average lighting/ beam angle : 120 to 160 deg 14. System power efficiency : > 85 % 15. Luminary Casing : Pressure die cast Aluminum with toughened glass cover and water proof fixture To be fixed on Octagonal Pole thru Arm. (Lumenaires S.L.)

Supply, installation, testing and commisioning of LED Focus light luminariesin place of existing non functional High mask Lights as per following specification 1. Input voltage : 150 V to 270 V 2.Lumens : Min 20000 3. Power factor : >0.90 4. Life expecting : more than 40,000 hours 5. No of hours usage / day : 10 to 12 hours/day 6. Rated watt : 200W 7. Luminous flux : Min. 20,000 8. Colour Temperature : 5,500 to 6,500 K with test certificate 9. Ingress protection : IP 65/IP 66 as per IS/IEC60529-2001 with test certificate. 10. Total harmonic distortion (THD): <15% with test certificate 11. Colour rendering index : Ra > 80 12. Working Temperature : 0 deg to 50 deg 13. Luminary Casing : Pressure die cast Aluminum with toughened glass cover and water proof fixture

Supply, installation, testing and commisioning of LED flood light luminariesin place of existing non functional High mask Lights as per following specification 1. Input voltage : 150 V to 270 V 2.Lumens : Min 5000 3. Power factor : >0.90 4. Life expecting : more than 40,000 hours 5. No of hours usage / day : 10 to 12 hours/day 6. Rated watt : 50-60W 7. Luminous flux : 5000 to 5500 lumens 8. Colour Temperature : 5,500 to 6,500 K with test certificate 9. Ingress protection : IP 65/IP 66 as per IS/IEC60529-2001 with test certificate. 10. Total harmonic distortion (THD): <15% with test certificate 11. Colour rendering index : Ra > 80 12. Working Temperature : 0 deg to 50 deg 13. Luminary Casing : Pressure die cast Aluminum with toughened glass cover and water proof fixture Alongwith Stand and to be installed at Ground, complete job as required at site.;

Providing and laying of spans of 3 ½ core/2 core XLPE Al. cable Armored of various sizes as mentioned below in place of damaged/burnt out / fresh ones of 1.1KV as per IS 7098/ II/ 85 with latest amendements

16 mm sq 2-core

Supplying and making end termination with and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 x 16 sq. mm

Supplying and fixing terminal block, suitable for 16 sq.mm conductor- 04 Way

Fixing of one number PVC insulated 16 mm Sq. 2core and PVC sheathed / XLPE power cable of 1.1 KV grade of following size as required, (clamped with 1mm thick saddle)

Painting of ST Poles with 1coat of Red Oxide primer and 2 coats of Al. Paint. The job includes the cost of snading, cleaning, preparing the surface, already erected Poles (upto 11 Mtr. Pole length)

Disconnecting , dismantalling of Existing Distribution Board, by way removing existing connections, and re-fixing of the DB, re-connecting the connections, after recessing in the wall , plastering complete job

Supplying and fixing , single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way Double Door

6 Way Double Door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . a) 8 way VTPN

Providing and fixing following rating and breaking capacity and Four pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.. (Lift) a) MCCB 100 A 4P having 30 KA B/capacity

Supplying and fixing following rating, 240/415 volts, “C”curve,10KA miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (MCB TP) (Lift) a) 63 Amp TP

b) 40Amp TP

Providing and laying of spans of 3 ½ core XLPE Al. cable Armored of various sizes as mentioned below in . (Lift) .

a) 35 mm sq 3 ½ core

Supplying and making end termination with and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

a) 35 mm sq 3 ½ core

Making of earthing point with 2 inch dia GI pipe , B class , caged in 6 inch GI pipe class B in CCM compound and 10 feet Deep, as earthing electrode . The pit is to be dug using borewell and covered with 10''X10'' inch manhole cover .

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

M.Y. ELECTRICALS

SHA INFRA