Extension of Bus Stand and C/O Rain shelter at Kanam in District Kinnaur (HP) (SH- Toilet Block, Rain shelter, WS and SI, Septic Tank and Soak pit and R/wall

Amount

Cutting in earth work and disposal of excavated earth upto a lead of 20 meters including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Excavation in soil in Hilly Area in all kind of soil, including cutting and trimming of side slopes and loading in truck and carrying of excavated materials disposing of excavated earth with embankment or dumping site as per clause 1603.1. & 1603.2, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out , construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto all lead dressing of sides and bottom and backfilling in trenches with excavated suitable material upto all depth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Excavation in foundations trenches etc in earth work in all kinds of soil, such as pick work, pick jumper work, jumper work, jumper blasting wrok, chiseling wedging out rocks including pumping or bailing out water upto all lifts, stacking the excavated soil not more then three metres clear from the edge of excavation and then returning the stacked soil in 15 cm (Fifteen centimetres) layers when required in to plinth side of foundations etcetra consolidating each deposited layer by ramming and watering and then disposing of all surplus exeavated earth as directed up to any lead by Engineer-in-Charge, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing form work with steel plates 3.15mm. (Three point one five milimetre) thick welded with angle iron in frame 30X30mmx5mm. (Thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling any floor/height and removal of the same for in situ-reinforced concrete and plain concrete work, Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floor etc. upto 200mm (Two hundred millimeter) in thickness. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Floor etc. upto 200mm thickness.

Columns, pillars, posts and struts. Square, rectangular or polygonal in plan.

Staircases with sloping or stepped soffits excluding landing.

Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Edges of slabs and breaks in floors and walls:Under 20 cm. wide.

Sides Sopits of beams haunchings cantilevers girders, bressumers and lintels exceeding 1 Mtr. in depth in all heights from floor.

Providing and laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specifications clause 802,803 1202 and 1203. 1:6:12 (One cement : six sand : twelve graged stone aggregate 40mm (Forty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and laying cement concrete 1:6:12 ( One cement : Six sand: twelve graded stone aggregate 20 mm nominal size) and curing complete excluding cost of centring and shuttering in Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve graded stone aggregate 20mm (Twenty millimeter) nominal size) at plinth level in Cement Mortar 1:6 (One cement: six sand) including curing and including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:5:10 (One cement : five sand : ten graded stone aggregate 40mm (Forty millimeter) nominal size) and curing complete excluding the cost of form work in Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Cement concrete 1:4:8 with 15% plum and curing complete including the cost of form work for plain and reinforce concrete in retaining wall/ Breast wall. Size of plum should be 150 to 300mm (One hundred fifty × three hundred millimeter) (For R/wall) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (One cement : two sand : four graded stone aggregate 20mm (Twenty millimeter) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floors two level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (One cement : two sand : four graded stone aggregate 20mm (Twenty millimeter) nominal size) and curing complete excluding cost of form work in: Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying reinforced cement concrete 1:1.5:3 (One cement : one point five sand : 3 graded stone aggregate 20mm. (Twenty millimeter) nominal size) and curing complete excluding cost of form work and reinforcement for feinforced concrete work in, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Suspended floor roofs, landings and shelves and their supports, balconies, beams, griders, bressumers and cantilevers upto two floor level

Column pillars posts and struts in foundation plinth upto all floor level complete in all respect

Providing Tor steel reinforcement for R.C.C. work including cutting, bending, binding and placing in position complete in super-structure for all floor level in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Square rubble masonary coursed with hard stone of approved quality in foundation and plinth in Retaining walls/Breast walls including rakingout joints in:- Cement Mortar 1:5 (One cement: five sand) Superstructure above plinth level and upto floor all level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Square rubble masonary coursed with hard stone of approved quality in foundation and plinth in Retaining walls/Breast walls including rakingout joints in:- Cement Mortar 1:5 (One cement: five sand) Superstructure above plinth level and upto floor all level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Brick work using common brunt clay building brick in foundation and plinth in cement mortar 1:3 (1cement : 3 Sand) second class bricks, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Half brick massonary in common burnt clay building brick in cement mortar 1:3 (1cement : 3 Sand) second class bricks, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing woodwork in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position. 2nd class Deodar wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing pannelled and glazed door shutter( in first class Deodar wood having Top rail 10x4 cm (Ten into four centimetre) middle rail 15x4 cm (Fifteen into four centimetre) and bottom rail 20x4 (Twenty into four centimetre) cm sash bar 4x4 cm (Four into four centimetre) and panel 12 mm (Twelve ) thick Phenol bonded (both side) prelaminated Bwp grade partical board in matt finish ISI marked IS.No. 12823 as per approved shade of Kavista or its equvalent below middle rail and above middle rail 5 mm (Five millimeter) thick glass)i/c black enammelled iron butt hinges with necessary screws etc comp. 40 mm (Forty millimetre) thick as per Arch. drg. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56mm (Zero point fifty six millimeter) for doors, windows and clerestory windows including first class deodar wood ornamental beading 20 mm × 12.5 mm (Twenty millimeter into twelve point five millimeter) section including bright finished black enamelled iron butt hinges with necessary screws 40 mm (Forty millimetre) thick 1st class deodar wood as per Arch. drg. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing 40 x 3 mm(Forty into three millimetre) flat iron hold fast 40 cm(forty centimetre) long including fixing to frame with 10 mm (Ten millimetre) dia bolts, nuts and wooden plugs and embeding in cement concrete block 30 x 10 x15 cm (Thirty into ten into fifteen) centimetre) in 1:3:6 (one cement :three sand :six graded stone aggregate 20 mm(Twenty millimetre) nominal size ). including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

200×10mm (two hundred fifty into ten millimeter)

100×10mm (One hundred into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete 100mm (One hundred millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing oxidized M.S. sliding door bolts with nuts and screws etc. complete. 250x16 mm (Two hundred fifty into sixteen millimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Precast terrazzo tiles hydraulic compressed 20 mm ( Twenty millimetre ) thick (with marble chips of specified sizes) fixed on wall on 10 mm (Ten millimetre ) thick cement plaster 1:3 (1 cement:3 sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Extra if cut tiles other half tiles had to be used in risers of steps, skirting and dado including rubbing and polishing complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying White glazed tiles 6 mm (Six millimeter) thick in skirting risers of steps and dado 20 mm (Twelve) thick cement mortar 1:3 (One cement : three sand) and jointed with cement slurry in Super-structure for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying spartic ceremic tiles 5.5mm. (Five point five millimeter) thick in flooring (300 x300mm. (Three hundred into three hundred millimeter) size) treads of steps laid on a bed of 12mm (Twelve millimeter) thick cement mortar 1:3 (One cement : three sand) finished with flush pointing in white cement. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting, fixing in position and applying a priming coat of red lead paint. , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

In gratings framed guard bars,ladders,railling,brackets and similar works.

In single Stanchions composed of rolled steel joists or channels with caps,bases splices,angles brackets etc.

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm. (Fifty millimeter) diameter welded in straight length over M.S. flat at top of vertical balusters including one of re oxide priming coat complete (M.S. flat and balushters of railings shall be measured and paid separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foregin matter and scoured with wire brushes fine steek wool scrapers and sand paper complete. With ready mixed priming paint brushing red lead, Red-oxide/zinc oxide chorme, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting one coat (excluding priming coat)on previously painted wood and wood based surfaces with readymixed paint brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

With readymixed paint other thanwhite

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting complete ready mixed paint brushing wood primer pink in Super-structure for all floor, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface all dirt, dust and other foreign matters with enamel paint other than white, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

6mm (Six millimeter) Cement Plaster to ceiling. In cement mortar 1:3 (One cement : three sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster in single coat on fair side of brick/concrete walls for internal plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80 mm (Eighty millimeter) in girth and finished even and smooth. Cement mortar 1:5 (One cement : five sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

White washing with lime on decorated wall surfaces(one coat) to give an even shade including thoroughly brooming the surface to remove all dirt,dust,mortar drops and loose scale of lime wash and other foreign matter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give and even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth .Priming coat with distemper primer, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing plinth protection 50mm. (Fifty millimetres) thick in cement concrete 1:3:6 (One cement:three sand: six graded stone aggregate crushed 20mm. (Twenty millimetres) nominal size) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing under layer for plinth protection of 75mm (Seventy Five milimeter) thick (unconsolidated) bed dry bricks/stone aggregate 40mm (Forty milimeter) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing course rubble hammer dressed Ú’shaped drain with the side wall 15×22 cm in cement mortar 1:6 (1cement:6sand) and inside plastering with cement plaster 1:3 (1cement:3sand) including earthwork and laying 10cm cement concrete in 1:5:10 (1cement:5sand:10graded staone aggregate of 40mm nominal size) and 7.5cm cement concrete 1:2:4 (1cement :4sand:4graded stone aggregate 20mm nominal size) and finished with a floating coat of neat cement complete as per standard design, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone soling properly hand-packed filling interstices with Kharanja stone and consolidating with power road roller to the required gradient and comber including spreading watering and rolling of binding materials moorum or earth etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Extra for squared rubble masonary coursed with hard stone of approved quality in superstructure above plinth level and upto floor two level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone work ashlar punched (ordinary work) in superstructure upto floor two level in cement mortar 1:6 (1 cement : 6 sand) including point with cement mortar 1:2 (1 cement:2 sand)including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Pointing on square rubble, coursed or un-coursed stone masonry with cement mortar 1:3 (1 cement: 3 sand) ruled pointing, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

20mm Cement plaster in two coats, backing coat 15mm and finishing coat 5mm thick on rough side of brick/stone masonary walls for interior plastering uptofloor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. Cement Mortar 1:4 (1 cement: 4 Sand)

Providing and laying Cement concrete flooring 1:2:4 (One cement : two sand :four graded crushed stone aggregate 20mm.(twenty millimeters) ) laid in one layer finished with floating coat of neat cement 40mm.(forty millimeters) thick in Super-structure for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone Filling behind retaining walls, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in trenches mild steel pipe 100mm dia G.I. pipe including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint :- In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.60mm (Zero point sixty millimeter) thick pre-painted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeter) dia metre with prepainted limpet and rubber washers complete with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick pre-painted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with pre-painted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 8mm (eight millimeter) thick partical board celling of approved quality with but jointing and nail (frame work and cover fillets to ve paid for separately , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing partical board celling of approved quality with but joining and nail (frame work and cover fillets to be paid for seperately 30mm thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. BP Sheet 1.66mm (One point sixty six millimeter to 2mm (Two millimeter) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Extra fot provinding and fixing strips in joints of terrazzo floors 40 mm (fourty milimeter) wide and 4mm thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting two coats (excluding primimg coat) on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt, dust and other forigin matters enamel paint other than white, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204. Random rubble masonry in cement mortar 1:6 (One cement: Six sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing weep holes in brick masonry /stone masonry/plain reinforced concrete abutments, wing wall, return wall,with 100mm (One hundred millimeter) dia PVC pipe extending through the full width of the structures with slope of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614,709,1204.3.7 (For R/wall) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 1204.3.8. Granular material (For R/wall), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Heavy grade) tube fitting and clamps including making good the wall, ceiling and floor, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter)nominal bore

20mm (Fifteen millimeter)nominal bore

Making connection of galbanised steel distribution branch with galvanised mild steel main 20mm (twenty millimeter) to 40mm (fourty millimeter) nominal bore by providing and fixing tree including cutting and threading the pipes complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (Fifteen millimeter) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level. 1000 (One thousand) litres net capacity tank, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Construction chamber 300mm x300mmx500mm (Three hundred millimeter into three hundred millimeter into five hundred millimeter) inside size for stop cock with C.I. surface box 100mm x 100 mm x75mm (One hundred millimeter into one hundred millimeter into seventy five millimeter) (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (One cement : two sand : four crushed stone aggregate 20mm (Twenty millimeter) nominal size) 75mm (Seventy five millimeter) thick foundation concrete 1:5:10 (One cement : five sand : ten crushed stone aggregate) 40mm (Forty millimeter) (nominal size) and inside plastering with Cement Mortar 1:3 (One cement : three sand) finished with a floating coat for neat cement including curing complete with 100mm cast in situ plain each 158.10 935.00 cement concrete walls in 1:2:4 mix(One cement : two sand : 4 grades stone aggregate) 20mm nominal size complete with form work including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing high pressure P.V.C.spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

50mm (( fifty millimeter) nominal size

110mm (One hundred & ten millimeter) nominal size

Providing and fixing C.I. cowl 100mm (one hundred millimeter) complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110mm × 75mm (One hundred ten millimeter into seventy five millimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing vitreous china wash basin water closet squatting pan (Indian type W.C. pan) size 580mm. (Five hundred eighty millimeters) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) Orrissa pattern, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC 'P'or 'S' trap for water closet (squatting pan) ISI marked including jointiing the trap with the pan and PVC pipe with approved adhesive etc. complete. 110mm (One hundred & ten millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT Coloured/ white high density polyethylene / poly propylene 10 (Ten) litres capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (Fifteen millimeter) nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm (Forty millimeter) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately: Flat back type of size 430mm x 260mm x 350mm. (four hundred thirty millimetre into two hundred sixty millimeter into three hundred fifty millimetre) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clamps etc. (all in C.P. Brass) including cutting holes and making good the same 32mm nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing vitreous china wash basin No. 10001 of Hindware or its equivalent with single hole for pillar tap with C.I or M.S brackets painted white including cutting holes and making good the same but excluding fitting, Flat back , 630mm × 450 mm (Six hundred thirty millimeter into four hundred fifty millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass waste for wash basin or sink. 32mm (Thirty two millimeter) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.I. Union for wash basin or sink:- 32mm (Thirty two millimeter) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass S Trap for wash basin and sink :- 32mm (Thirty two millimeter) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 100mm (hundred millimeter) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600mm x 450 mm bevelled edge mirror of superior glass, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing chromium plated Toilet paper holder C.P. Brass, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Division Plate for Urinals 600mm × 300 (Six hundred millimeter into three hundred millimeter) Vitreous China, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge in all leads and lifts.

Providing and fixing C.P Brass Bib tap with capstan head (Superior or heavy type) 15mm (Fifteen millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass pillar tap with capstan head 15mm (Fifteen millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass angle valve 15mm (Fifteen millimeter) without Nuts and pipe, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing P.V.C. connection with brass unions:- (a) 300/450mm (Three hundred/four hundred fifty millimeter) length. 15mm (Fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

20mm (Twenty millimeter) nominal bore

Providing and fixing 32mm (Thirty two millimetre) C.P. Brass waste, and plug for glazed ware sinks, basins, etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug,brass chain and stud : providing, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and lfixing brass full way valve with wheel, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter) nominal bore.

20mm (Twenty millimeter) nominal bore.

Providing and lfixing brass ball valve (horizontal plunger type), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter) nominal bore.

Providing and lfixing G.I./M.I Union of following sizes where not included in the items, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter) nominal bore.

20mm (Twenty millimeter) nominal bore.

Constructing manhole with RCC top slab in 1:2:4 mix (One cement: two sand: four graded crushed stone aggregate 20mm (Twenty millimeter nominal size), foundation concrete 1:4:8 (One cement: four sand: eight graded crushed stone aggregate 40mm (forty millimeter) nominal size, inside plastering 15mm (Fifteenmillimeter) thick with cement mortar 1:3 (One cement: Three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty millimeter) nominal size, finished smooth complete: - (i) In side size 800mm× 800×500mm (Eight Hundred into Eight hundred Five hundred millimeter) deep including C.I cover with frame. (Light duty single seal: pattern 1) 455mmX 610mm (Four Hundred Fifty Five x Six Hundred Ten millimeter) internal dimensions total weight of cover and frame to be not less than 38Kg. (thirty eight Kilogram) (Weight of cover 23Kg. (Twenty Three kilogram) and weight of frame 15Kg. (Fifteen Kilogram.) (a) With 200mm (Two Hundred millimeter. thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(One cement: Three sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

rattan kirti