Construction of Office Building for District Ayurveda Medical Officer, At - Debendrapur, Bariapada, Dist- Mayurbhanj.

Plinth Protection

Approach Road

Supplying and filling in foundation and plinth with good quality river sand including watering, ramming with cost, conveyances, royalties, taxes of all materials and cost of all labour with T&P required for the work etc. complete as per specification & direction of Engineer-in-charge. Ground Floor

Plinth Protection

Approach Road

Providing and applying of Post construction Anti-termite treatment by drilling 12mm dia. holes at distance of 30cm @ junction of wall and floor about 300mm aprt deep

enogh to reach the soil below and chemical emulsion (PREMISE, IMIDACHLOPRIED 30.5SC OF BAYER MAKE mixed with 47.5 ltr water) pumped these holes to soak the soil @ 1 ltr soulation of each hole as per manufactures specification and the holes should be pluged with filling materials including cost of all material, labour conveyance and hiring charges of machinaries all taxes as per direction of EIC - Ground Floor

Plinth Protection

Approach Road

Providing and laying plain cement concrete of proportion (1:3:6) in foundation and floors using 4 cm. size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality and from approved quarry including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm. thick in each layer including cost, conveyance, royalties, taxes of all materials and cost of all labours,labour cess, T&P etc complete as per the direction of the Engineer-in-charge. Ground Floor

R.C.C. work of M-25 in following works using 12 mm. to 20 mm. (½” to ¾”) size (20 mm. not to exceed 25%) hard black crusher broken granite stone chips of approved quality from approved quarry including hoisting, lowering, laying and compacting concrete, watering curing, centering, shuttering and finishing the exposed surfaces smooth with cost, conveyance, royalties, taxes of all materials with all labour,labour cess and T & P required for the work etc. complete in all respect but excluding the cost and conveyance of M.S. rods or Tor steel and binding wire of 18 to 20 gauge and labour charges for straightening, cutting, bending, binding and tying the grills and placing in proper position and as per the direction of the Engineer-in-charge. Ground Floor

Column Base

Column

Lintel band

Chajja

Grade Beam

Roof Beam

Stair Case

Roof Slab

Window Shelves

Column

Lintel

Chajja

Grade Beam

Roof Beam

Roof Slab

First Floor (Head Room)

Window Shelves

Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of primary steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL / SHYAM STEEL (grade Fe-500D) etc. including bending, binding, welding and jointing if necessary and tying the grills and placing in position as required for R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying including cost, conveyances, taxes of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all floors with labour cess etc. (payment will be made on standard weight of B.I.S. for M.S. Rods or tor steel only) etc. complete as per specification & direction of Engineer-in-charge. Ground Floor

Fly ash Brick masonry using bricks of size 23cm. x 11 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix (1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar after immersing the bricks for 6 (Six) hours in water before use in Foundation & Plinth including splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as directed by the Engineer-In-Charge.

Head Room

Plinth Protection

Fly ash Brick masonry using bricks of size 23cm. x 11 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix( 1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar after immersing the bricks for 6 (Six) hours in water before use in Superstracture including splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as directed by the Engineer-In-Charge. Ground Floor

Cement concrete (1:2:4) with 12mm size chips of approved quality etc.comp.- Plinth Protection

Earthwork in hard soil with initial lead and lift including rough dressing and breaking clods upto 5cm to 7cm size and laying in layers each layer not exceeding 0.3m in depth etc. complete- Approach road

First class Fly ash Brick masonry using bricks of size 23cm. x 11 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix (1:4) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar after immersing the bricks for 6 (Six) hours in water before use in Superstracture including splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as directed by the Engineer-In-Charge Ground Floor

Window Shelves

Providing 16 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties and taxes of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge. Ground Floor

Window Shelves

Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties and taxes of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge. Ground Floor

Providing fitting and fixing of false ceiling with Aluminum anodised T Section No. 3215 with 2'-0 center to center, L section NO. 1705 upto 15 micron on 4 walls to be fixed by means of steel screw and P.V.C plug and the Aluminium grid 2-0 x 2" - 0" with 6mm thick plain A.C.Sheet of 125mm thick. etc. complete - Ground floor

Window Shelves

Supplying, fitting and fixing vitrified tile in floors of size 600mm x 600mm of colour/printed approved make conforming to IS: 13755 laid to 20mm thick cement mortar(1:4) (1 cement : 4 course sand) and filling joints with white cement of approved quality including cost of all materials, labour T&P etc required for the work all complete as per direction of Engineer-in-Charge. ( For New work Only) Ground Floor

Supplying, fitting and fixing Anti-Skid ceramic tile in floors, treads of steps and landing on 20mm thick cement mortar(1:4) (1 cement : 4 course sand) and filling joints with white cement of approved quality including cost of all materials, labour T&P etc required for the work all complete as per direction of Engineer-in-Charge. ( For New work Only) - Ground floor

Supplying all materials, labour, T&P and fixing porcelain glazed tiles in dados skirting on 12mm thick cement plaster (1:3) joint

ed with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete as per direction of the Engineer in charge. - Ground floor

Window Shelves

Fixing Granite tiles above 0.40sqm in floors,treads and landings on 25mm thick bed of cement mortar (1:1) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile. - Ground floor

Fixing vertified wall tiles in dados, (600mm x 600mm) skirting and in rises of steps on 12mm thick bed of cement plaster (1:3) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile. Ground Floor

Fixing Vetrified industrials floor tiles of premium grade having thickness 8mm to 10mm confirming to IS 4457 of size (300mm x 300mm) in floor and in rises of steps on 25mm thick bed of cement plaster (1:1) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile - Ground floor

Window Shelves

Fixing Vetrified industrials Wall tiles of premium grade having thickness 8mm to 10mm confirming to IS 4457 of size (300mm x 300mm) in dados,skirting and in rises of steps on 12mm thick bed of cement plaster (1:3) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile - Ground floor

Supplying of M.S. Windows Grill made out of structural steel, flats, plates, bars confirming to IS for windows, ventilators etc. as per drawing and design, fixed to walls with clamps including priming 1 coat with all kdamages in walls and floors etc. including cost of all materials, labour, conveyance, taxes, royalties, scaffolding, watering, curing, sundries, tools and plants etc.as per the direction of the Engineer in Charge. Ground Floor

Supplying of M.S. Door Grill made out of structural steel, flats, plates, bars confirming to IS for windows, ventilators etc. as per drawing and design, fixed to walls with clamps including priming 1 coat with all kdamages in walls and floors etc. including cost of all materials, labour, conveyance, taxes, royalties, scaffolding, watering, curing, sundries, tools and plants etc.as per the direction of the Engineer in Charge. - Ground Floor

Supplying fitting fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balstrade of size 32mmx32mmx2mm @0.90mtr C/C and stainless square pipe bracing of size 32mmx32mmx2mm in 3 rows in stair case as per approved design and specification, buffing, pollishing etc with cost, conveyance taxex of all materials, labour, T&P etc. required for the complete in all respect. - Ground Floor

Providing and fixing 65mm x 125mm factory made single extruded WPC (Wood polymer composite) solid door/window/ceosetory windows & other Frames/chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (Maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge. (Make: WPC:Century/Black Cobra/Rajshri Plastiwood, Hardware fitting: Godrej/Dorset/Link/Dorma) - Ground Floor

Providing and fitting, fixing of 32 mm thick flush door shutters conforming to IS 2002 (Part-1) decorative type, core block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both face of shutters inclussive of 4 nos of stainless steel Butt Hinges (100mm x 60mm x 2.5mm) 40mm stainless steel screws. Cylindrical Look(Godrej-9843), Tower Bolts SS 10mm X 300mm (Bathroom)(Godrej 3264), PVC Door Buffer with SS Screw, teak wood lipping around the edges & paste with 1.5mm thick lam8inate on both side of the flush door, etc., including the cost of all materials, hardware fittings, cost of all labour, convence, loading, unloading, T&P, etc , complete as per the direction of Engineer-in charge. - Ground Floor

Window Shelves

Supply and fitting-fixing of Un-plasticised Poly Vinyl Choloride (UPVC) (FENESTA/NCL VEKA LTD). Casement Door-Window-60- Series duly manufactured using UPVC reinforced profiles of 60mm x 55mm x 2.5mm for outer frames, 102mm x 60mm x 2.25mm for casement Door Sash Profile and 74mm x 60mm x 2.5mm mullion profile capable of mounting single glazing system, system, structurally reinforced with hot dip galvanised up to 50 microns of minimum thickness of 2.0mm prefabricated & welded through fusion welding teh door frame shall be fitted with 12mm thick WPC Board of Greenly make duly fixed with EPDM weathering seal resistant accessories like clipping locking system made of aluminium 1 No., per set of sashes and the system is to be installed at the site using anchor fasteners silicon rubber sealant, easy glazing/deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges, materials and product conforming to ASTM D 368-14, EN-477-95 and other applicable codes and standards - Ground Floor

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Ref.-DSR-Page-549, Item-9.147D.3) Ground Floor

Window Shelves

Supply and fitting-fixing of Un-plasticised Poly Vinyl Choloride (UPVC) (FENESTA/NCL VEKA LTD). Ventilator / Top Hung-60-Series duly manufactured using UPVC reinforced profiles of 60mm x 55mm x 2.5mm for outer frames, 75mm x 60mm x 2.25mm for casement Window Sash Profile capable of mounting single glazing system, structurally reinforced with hot dip galvanised up to 50 microns of minimum thickness of 1.5mm prefabricated & welded through fusion welding the Window Sash shall be fitted with 6mm thick clear toughened glass of SAINT-GOBAIN make duly fixed with EPDM weathering seal resistant accessories like clipping locking system made of aluminium 1 Nos., per set of sashes and the system is to be installed using anchor fasteners, silicon rubber sealant, easy glazing/deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges, materials and product conforming to ASTM D 368-14, EN-477-95 and other applicable codes and standards - Ground floor

Window Shelves

Providing and fixing of Fixed Glazing with part Top hung of approved make to be fabricated from roll formed sections made of pre-painted steel etc. complete. (S/R page 249, item No. 14) Ground Floor

Window Shelves

Finishing wall surface with Acrilic wall putty (water based) of approved make and finish smooth and even surface to receive painting including cost of all materials labour T&P etc complete. Ground Floor

Window Shelves

Wall Priming one coat with wall cement primer water bound etc. complete Ground Floor

Window Shelves

Wall painting two coats with plastic emulsion paint of approved shade including costof paint. Ground Floor

Window Shelves

Wall painting two coats with weather coat paint of approved shade including cost of paint. Ground Floor

Window Shelves

Priming one coat with any approved primer including cost of primer over iron work etc. complete. Ground Floor

Painting two coats with any approved paint including cost of paints over iron / Wood works. Ground Floor

Providing 20mm thick grading plaster using cement plaster (1:4) on roof slab cost, carriage, royality taxes and all labour involved for the completion of item of work as per direction of EIC. - Ground Floor

2.5cm thick grading concrete (1:2:2) on roof slab using 6mm size hard granite chips including watering, curing etc.complete - First Floor

per hour

Providing fixing and fitting of 110mm dia P.V.C. rain water pipe of approved quality and approved make confirming to I S with necessary bends and clamps etc.complete fixed to wall with nail etc as per the direction of EIC including cost of all material with taxes labour T&P etc complete. - Ground Floor

Supplying and fixing of 80mm thick cement concrete interlocking paver block of M-40 grade of approved make, design, colour and size made by Block making machine with proper compaction laid in required pattern etc. complete in all respect conforming to IRC SP-63:2018.

Group-B L.P- F.P- C.B.P-

Group-C L.P- F.P- C.B.P-

Recessed wiring to submain in the following sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked conforming to IS-694/1990 in the following mm dia non-metallic heavy duty flexible conduit 1.6 mm thick along with the following sq.mm FR PVC insulated single core multistrand copper conductor as earth wire as required.(Make of wire-Finolex/L&T/Anchor/Havells/V-Guard//HPL or any other approved make) 2 X 1.5 sq.mm +1 X 1.5 sq.mm in 20 mm dia

2 X 2.5 sq.mm +1 X 1.5 sq.mm in 20 mm dia

2 X 4 sq.mm +1 X 1.5 sq.mm in 20 mm dia

2 X 6 sq.mm +1 X 2.5 sq.mm in 25mm dia

4 X 6 sq.mm + 2 X 2.5 sq.mm in 32 mm dia

2 X 1.5sqmm (for inverter wiring)

Supply and fixing of 6Amp plug with 6Amp switch on existing board (Modular type)

Point wiring for 5 / 6 amp modular socket outlet with 2 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked in recess 20 mm dia non-metalic PVC flexible conduit with modlular switch , modluar cover plate suitable size ISI marked earthing point with 1 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor for loop earthing etc. as required. ( Make of wire Finolex / L&T / Anchor / Havels / V Guard or any other approved make )

S/F of modular 6-16amp 3 pin modular shuttered socket with 16 Amp modular DP switch with indicator on 4 module GI box, wiring of plug with 4 sqmm wire, running earth with 1.5 sqmm PVC insulated copper conductor, 4 module cover plate in front complete in all respect suitable for friedge/ washing machine/ induction cook top point (Make of switch and socket- Havells/ Legrand/ Anchor or any other approved make)

Supply and fixing of 32amp motor starter on 2 module flush type GI box with suitable cover plate in front, 4 sqmm single core multistrand copper conductor as required between starter and 6-16 amp 3 pin shutterd socket on another flush type GI box

SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2200 lumen complete with electronic driver and all other accessories with diffuser having 5 years warranty i/c connection etc as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 5 years .

Supplying, installation, testing and commssioning of 1200 mm sweep BLDC ceiling fan with aluminium blades having wattage not more than 28W and Air delivery ≥ 215(m3/min) Make-USHA(Teohnix)/Crompton(Energion Groove)/Havells(Efficiencia Neo or equievalant reputed make & model A catagory ISI marked as approved ) including wiring the down rod of standard length (upto 30 cm) with 1.5 sq mm PVC insulated, copper conductor, single core cable etc. as required as per direction of Engg.-in-Charge,Replacement Warranty will be 4 years.. .(With fan Regulator)

Supply & fixing of LED Gate Light with all accessories.

Supply & fixing of LED 36w 2'x2' Surface/Recessed Mounted Light Equivalent. etc as required .

Supply and fixing of Electronic Step Type socket size fan regulator (Make-Cona/ Anchor/ Usha/Bajaj or any other approved make)

Supply and fixing of 300mm Exhaust Fan, Motor Speed: 1400 RPM Metal Blade, Double ball bearings heavy duty motor, metal bird guard, Air delivery (minimum): 1850 m³/h, Noise level : 40-45 dB

Supply and fixing of 90 watt led streetlight Endura citylite platinum energy saving and environmental friendly long lige LED street light made up of pressure die cast alluminium housing with acrylic cover as diffuser with IP66 pretection and impact resistance of IK07

Supply and fixing of 9Watt LED bulb, holder base type: B22 , Colour Temperature 6500 Kelvin Average Life 10000 Hours(Make- Havells/ Philips/Crompton or any other approved make)

S/F of 2 nos of 6/10 amp modular switch and 6 amp 5 pin shuttered socket on 8 module GI box with modular base plate and modular cover plate in front, complete in all respect (make of wire- Finolex/ L&T/ Anchor/ Havells/ V-Guard or any other approved make)

S/F of 4 nos of 6/10 amp modular switch and 6 amp 5 pin shuttered socket on 12 module GI box with modular base plate and modular cover plate in front, complete in all respect (make of wire- Finolex/ L&T/ Anchor/ Havells/ V-Guard or any other approved make)

Supply and fixing of following way Horizontal type TPN DB in recess , Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, IK 09 protection rating double door DB, available in CRCA sheet steel, RAL 9003, powder coated, Ready to use DBs - Provided with 100A insulated phase bus-bars, neutral bar/s with shroud/s , earth bar/s . sticking saddles , cement spill protector , color-coded interconnecting wire set , cable ties , blanking plates and circuit identification labels With provision for FP MCB/Isolator/RCCB/RCBO as incomer and SP MCBs as outgoings(Make- L&T, Legrand or any other approved make) 4 way Horijontal TPN DB Double Door with MCB Incomer

Supply and fixing of following way single pole and neutral sheet steel MCB distribution board 250V on surface/recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (but with out MCB/ RCCB/ Isolator) make-HPL/ Havells/ Legrand /L&T/C&S or any other approved make.) 8way, Double door

Supply and fixing of following rating 240 V/415 V "C" series MCB suitable for lighting and other loads of the following poles in the exiting MCB DB ISI marked complete with connections testing and commissioning etc. (Make-HPL/ Havells/ Legrand /L&T/C&S or any other approved make) SP MCB 6-32A C-series

DP MCB 32A C-series

FP MCB 32A C-series

Supply and fixing of 40 Amp DP RCCB, 30 mA in existing distribution box with all accessories complete in all respect(Make- L&T/ Havells/ Legrand or any other approved make)

Supply and fixing of 40 Amp FP RCCB, 30 mA in existing distribution box with all accessories complete in all respect(Make- L&T/ Havells/ Legrand or any other approved make)

Extra for using salt and charcoal for G.I. or copper plate earth as required

Supply and laying 8 SWG copper wire ISI marked at 0.5 meter below ground level for conductor earth electorde including soldering etc. as required

16/18 SWG pannel box 36 X 24X 10=8640 sq. inch for single door made out of CR sheet of 16SWG and boarder angle frame to provide above pannel with proper space ,hinges, and other accessories , hinged door must be painted one coated red oxide and two coat enamel gray paint.

Supply and fixing of internal wiring to equipment installed in the pannel board with required size of copper multistrand single core cables duly crimped with copper lugs and all connections 36 X 24 including cost of copper conductor and other fittings like gasket ,screw , nut and bolt , insulating materials etc.

S/F of 100 Amp four pole MCCB, 30KA in existing Panel

Supply and fixing of 100 A onload Changeover Switch-Disconnector in open execution (Conforms to IEC 60947-3, IS/IEC 60947-3)

S/F of coper bus bar 25 x 5mm with required size of insulating material and nut and bolts.

Supply and fixing of following rating 240 V/415 V "C" series MCB suitable for lighting and other loads of the following poles in the exiting MCB DB ISI marked complete with connections testing and commissioning etc. (Make-HPL/ Havells/ Legrand /L&T/C&S or any other approved make) SP MCB 6-32A C-series

Supply and fixing of following way single pole and neutral sheet steel MCB distribution board 250V on surface/recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (but with out MCB/ RCCB/ Isolator) make-HPL/ Havells/ Legrand /L&T/C&S or any other approved make.) 8way, Double door

Supply and fixing of LED Indicator lamp

Supply and fixing of SPD,40KA/Pole Cat. Nos 412243,4P ,4Modules,(Make:-Legrand,and other approval Make )

Supply and installation of Rubber Mats 12mm thick of size 2000mm x 1000mm x 12 mm thick Electrical tested with test certificate.

Supply and fixing of fire buckets with angular fabricated stand to fix 4 buckets in each stand for Electrical fire protection as per standards of Electrical Inspectorate.

Supply and fixing of Co2 fire extinguisher with mounting clamps with pressure test certificate .

Providing ,fixing , testing and commissioning of Portable ABC powder type fire extinguisher 6 Kg capacity containing Mono Ammonium Phosphate Powder 50, Stored Pressure Type, fitted with Discharge hose, brackets etc., The discharge

Range shall be minimum of 4 mtrs.The Internal Coating of Can shall be Epoxy Powder coating and External painted with Epoxy Polyester Powder coating.The thickness shall not less than 1.6 mm made of Sheet metal.The Fire Extinguishers shall be ISI Approved as per IS 15683:2006.Vendor shall consider the suitable signages along with the extinguishers.CEASE FIRE,SAFEGUARD,SAFEX,)

Supply and fixing of shock treatement charts duly laminated along with separate colour single line diagram laminated, to be fixed in Electrical control panel room.

Supply and fixing of first aid box with medicines complete with medicine with three years expiry date to be fixed in Electrical control panel room.

Supply and fixing of 2KVA/24 volt Sine wave UPS inverter with maximum bulb load 1500 watt, Max charging current 21amp, MCB protection, 2 nos of tubular battery 150AH capacity

Supply of Elegant look 60 W (+/-10%) AIO LED Solar Street lights having extruded alluminium housing, 180Wp or more Mono Crystalline Panel/Laminates fixed on the top of the luminaire housing, maintenance free 12.8 volts 78 Ah or more LiFePO4 battery(BIS certified) , BMS, MPPT charge controller, PIR sensor to provide 2 days (24 hrs ) back up . The luminaire is having IP 65 protection for critical components, IK 07 and having lumen output of > 10000 lumen and having minimum lumen efficacy >160 lm/w) as per LM 79 report third party NABL lab to justify the lumen output & lumen efficacy . Lenses should be provided on the LED chip for better lighting dstribution to avoid glare on human eyes. Both the luminaire and Mono Crystalline Panel must be manufactured in India. The Solar lighting company must submit the third party NABL lab reports to justify the luen efficacy,luminaire output , IK 07 and IP 65 protection ( In house NABL lab reports will not be acceptable). The Luminaire should be supplied along with adjustable type mounting bracket which can be fitted directly on the pole. The Solar Street light and solar panel having capacity of 180 Wp or more must be designed to take the wind load at 180 KM/HR wind speed (As per wind load test report ) . The Solar lighting companies should submit the lighting design report prepared by their in house lighting design for achieveing desired lux level if required as per the direction of engineer in charge .The Solar lighting manufacturer must submit the declaration letter by mentioning that complete solar light and the solar panel are manufactured in India ( Made in China product are not acceptable) and warranty certificate on their company's letterhead by mentioning warranty period as 5 years and necessary aftersales ervice will be provided through their tollfree base service network located within 100 KM from the project site. The Solar Street light manufacturer should have own NABL accredieted laborotory. The Scope of work includes 5 years comprehensive maintainace work including repair /Maintainance/Replacement of the product in case of any defect including labour/ The following test reports must be submitted for the technical acceptance of the products. 1.LM 79 REPORT (Third party NABL lab only) , 2. IK 07 (Report of Third party NABL lab only for any wattage of AIO solar light ) , 3. IP 65 (Report of Third party NABL lab only , 4. Wind load test report of AIO Street light having 180 Wp or more capacity Solar Mono Panel suitable for 180 KM/Hr wind Speed. The AIO solar street light must complies to the following : 1. EN50530 – MPPT Efficiency , 2.. IEC61547 , 3. IEC61000-3-2 – EMC , 4. IEC 60598-2-3 ,5. IEC 62109-1, ( The necessary test reports of third party NABL lab against the above must be submitted for any wattage of AIO Solar street lights for acceptance of product/TDS approval prior to start of the work. All the test reports must be in the name of solar lighting company ) Make- (Philips/Panasonic/Wipro/Havells/Bajaj/Crompton )

Supply of 8 mtr long hot dip galvanized Octagonal pole having base dia of 155 mm and top dia of 70 mm and plate thick ness of 4 mm or more. complete with base plate and 4 nos. Jtype En 8 grade foundation bolts to withstand 180 KM / HR or more wind speed considering the weight & dimension of 1 nos 60 W AIO Solar light to be fitted in the pole at two diffrent heights ( One light on Pole Top and second light on the differential bracket) (Make - Bajaj/Vakrangee/Valmont /RR Ispat/ Utkarsh)

Construction of RCC foundation by using M20gradeRCC and Fe415 grade reinforcementin the foundation by considering the SBC as 10 T per sq mtr and fixing 4 nos. EN8 grade foundation bolts in that foundation for installation of pole with solar lighton that foundation.The work shall be executed as per the instruction of EIC .

Installation of 8 mtr pole on the adaptor plate after fixing the 60 W AIO Light in the pole by using suitable machinery by taking all safety precautions as per the direction of EIC. (make- as approved by PWD Odisha)

Supply of following PVC armored cables ISI marked.(Make- Glowstar/ Polycab/ Nicco/KEI/HPL/ Mescab or any other approved make) 25sq.mm 3 1/2 core

3 1/2 X 25sqmm

Supplying and laying

of size 63 mm dia (OD-63 mm & ID-51 mm nominal) DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

Supply and fixing of 50mm dia medium class GI pipe with fixing of fan hook complete in all respect

Laying of one number of PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation, sand cushing, protective covering and refilling the trench etc. as required.

32mm dia UPVC ASTM-D Pipes

40mm dia UPVC ASTM-D Pipes

Supplying all materials , labour, T&P and providing and fixing to wall or ceiling and floor PVC pipes conforming to C-PVC1785/89 ( Sch-80 ) and G.I pipe fittings of the following nominal bore with clamps including making good the wall,ceiling and floor ,testing all complete as per P.H. specification and direction of Engineer-in-charge .(Supreme/Ashirvad/Oriplast) 25mm dia C-PVC Pipe

20mm dia C-PVC Pipe

Supplying all materials,labour,T&P and cutting holes through existing brick work including making good the damages in cement mortar(1:4) for taking GI pipes and fittings/PVC pipes and fittings etc.all complete as per PH specification and direction of the Engineer-in-charge. 250mm thick wall

Supplying all materials , labour, T&P and cutting holes in RCC floors and roofs upto 19cm thick for passing P.V.C pipes and G.I fittings etc. , and repairing the holes after insertion of pipe etc. with cement concrete (1:2:4) including finishing complete so as to make it leak-proof as per P.H. specification and direction of Engineer-in-charge In ground floor

Supplying all materials , labour, T&P and cutting grooves in pucca floors and walls for taking P.V.C pipes and G.I fittings etc. and making good the damages including finishing complete as per P.H. specification and direction of Engineer-in-charge. In ground floor

Supplying all materials , labour, T&P and fixing rotational moulded polyethylene cylindrical vertical water storage tanks conforming to IS:12701/1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc. including hoisting upto a height of 5 metres above ground level and placing the tank to the required position and providing 5.40 mtr. lengthx0.25 mtr width KB brickwork in cement mortar (1:6) of 0.46m height in staging and 0.13mtr thick circular protection wall of 0.46mtr height to support the tank,12mm thick cement plaster in cement mortar (1:6) over brick work, RCC slab of size 1.60mX1.60m and 0.10m thick ,RCC beam of 0.25mx0.30m and 2.60m average length in cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips including centering and shuttering,watering,curing ,cost of all materials,conveyance of all materials to worksite , payment of royalty, all taxes etc.all complete as per approved drawing , P.H. specification and direction of Engineer-in-charge.( Sintex/Supreem/Rotomax)2000 ltrs capacity rotational moulded polyethylene cylindrical vertical water storage tank -In first floor

Supplying all materials , labour, T&P and fitting and fixing brass/CP fittings of following nominal bore with supply of all jointing materials complete as per P.H. specification and direction of Engineer-in-charge 15mm C.P.Bib cock(Cat.No-CQT-CHR-23037)Jaquar.

15mm C.P.Pillar cock(Cat.No-COP-CHR-011PM)Jaquar.

15mm dia CP Angle Stop cock.(Cat.No-FLR-ABR-5053N)Jaquar.

25mm dia brass fullway valve(Shakti Make)

32mm dia brass fullway valve(Shakti Make)

40mm dia brass fullway valve(Shakti Make)

15mm dia CP two way Bib Cock ( Cat-No-FLR-ABR-5041N)Jaquar.

15mm dia. C.P extension piece

15mm dia. C.P flange

125mm dia CP gratting

Health faucet.(Cat.No-ALD-ABR-563)Jaquar.

Supplying all materials ,labour ,T&P and fixing 10 litres capacity PVC low level flushing cistern with a pair of PVC brackets complete with fittings such as pvc siphonic arrangements, 15mm dia nominal size pvc ball valve with polythene float ,pvc handles, unions and couplings for connection with inlet, outlet and overflow pipes, 32mm dia CP long flush bend, 15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet , and connecting the inlet pipe with supply main etc.all complete as per specification and direction of Engineer-in-charge 10 ltrs. capacity PVC L.L cistern with flush bend(Parryware/Hindware/Cera/Kerovit/Somany)

Supplying all materials,labour,T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No.13592/1992 to walls with nails,bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification,testing,earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of Engineer-in-charge 110mm dia U-PVC SWR Pipe (Supreme/Ashirvad/Oriplast)

110mm dia U-PVC Door Tee

110mm dia U-PVC Plain Band

110mm dia U-PVC Plain Tee

110mm dia U-PVC Offset without ear

110mm dia U-PVC Plain Shoe Bend

110mm dia U-PVC Door Cross Tee

110mm dia U-PVC Door Bend

110mm dia U-PVC 'P'Trap

110mm dia U-PVC Cowl

110mm dia U-PVC Socket plain

Supplying all materials , labour, T&P and cutting holes through existing brick or laterite masonry wall for taking U-PVC / HCI pipes and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge 250mm to 375mm thick wall

Supplying all materials, labour, T&P and cutting of R.C.C roof or cornice for taking H.C.I pipes and making good the damages etc all complete as per P.H.Specification and direction of the Engineer in charge.

Supplying all materials , labour, T&P and cutting of RCC chajja for taking HCI or U-PVC pipe and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge

Supplying all materials , labour, T&P and fixing Vitreous china water closet ,squatting pan ( Indian type W.C. pan / Orissa pattern squatting pan ) duly embedded in cement concrete 1:5:10 using hard granite metal 4cm nominal size including fixing a pair of vitreous china 250mmx130mmx30mm foot rest, fixing 100mm dia hci 'P' or 'S' trap for water closet squatting pan including jointing the trap with pan in cement mortar (1:1), cutting the floor and mending good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge 580mmx440mm size Orissa Pan (Parryware/Hindware/Cera/Kerovit/Somany)

Supplying all materials,labour,T&P and fitting and fixing vitrous Chaina washed down water Closet (European type water closet - EWC) with integral "P" or "S" type trap to the floor including wodden plug and chromoum plated screw including jointing the trap with soil pipe in CM(1:1) fixing plastic seat cover for washed down water closet with crmium plated brass hinges and rubber buffers including polishing etc all complete as per specification and direction of Engineer-in-charge. One Piece Closet "Berlin"(Cat.No-92099)Hindware

Supplying all materials ,labour ,T&P and fixing Wash basin with hole for pillar taps with cast iron or MS brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc. fixing pedestral for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply m

ains for wash basin , fixing 12mm dia CP brass waste etc.all complete as per specification and direction of Engineer-in-charge.550mmx400mm size wash hand basin with Porcelain pedestal(Parryware/Hindware/Cera/Kerovit/Somany)

Supplying all materials ,labour ,T&P and fixing wash kitchen sink with outlet at end and weir overflow including fitting and fixing a pair of cast iron or MS brackets painted white, fixing 50mm/40mm dia CP brass waste , fixing 50mm/40mm dia PVC waste pipe 910mm long with supply of wooden plugs, screws and cement etc. including cutting holes in walls and making good the damages etc.all complete as per specification and direction of Engineer-in-charge 600x450x250 mm stainless steel kitchen sink with drain board-glossy-IS:13983 - 1994 (Jayna make)

Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 4cm size hard granite metal including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing cement concrete ( 1:2:4 ) with 12mm size crusher broken hard black granite chips including watering, curing,cost of all materials, conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge

Supplying all materials ,labour ,T&P and fixing Mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with chromium plated brass screws and washers etc.all complete as per specification and direction of Engineer-in-charge Mirror(Bevellededge) 600mmx450mm

Supplying all materials,labour,T&P and fixing standard sized Glass-shelf with C.P brass bracket and guard rail complete fixed to wooden pluges with screw etc.all complete as per specification and direction of Engineer-in-charge.600mmx125mm size glass shelf with C.P ruard rail

Supplying all materials ,labour ,T&P and fixing standard sized CP brass towel rail complete with CP brass brackets fixed to wooden plugs with chromium plated brass screws etc.all complete as per specification and direction of Engineer-in-chargeC P Towel Ring

Supplying all materials ,labour ,T&P and fixing CP Soap Holder complete with CP brass brackets fixed to wooden plugs with chromium plated brass screws etc.all complete as per specification and direction of Engineer-in-chargeCP soap holder

Supplying all materials,labour ,T&P and filling in foundation and plinth with sand well watered and rammed including cost, conveyance of all materials to work site ,payment of royalty,taxes etc. all complete as per direction of the Engineer-in -charge In ground floor

Fitting and fixing vetrified tiles with matt finish Kajaria ( Fog Perla or equivalent ) on floor or steps & landing on 25mm. Thick bed of cement mortar (1:1) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including cost conveyance, roylalities and taxes etc. all complete as per direction of Engineer-in-charge.(600mmx600mm)

Supplying all materials,labour,T&P and providing 12mm thick cement plaster(1:4) on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge.

Fitting and fixing vetrified tiles with matt finish Kajaria ( Duren Marfil / Equvalant) to dados skirting & risers of steps on 12mm tick C.P(1:3) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including cost conveyance, roylalities and taxes etc. all complete as per direction of Engineer-in-charge.

Supplying all materials ,labour ,T&P and constructing Inspection Chamber of inside size 760mmx760mmx460mm with cement concrete (1:3:6) using 40mm size crusher broken hard black granite metal on bed , KB brick work in cement mortar (1:6) in foundation and plinth, moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips, 12mm thick cement plaster (1:3) with cement punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab (1:2:4) using 12mm size crusher broken hard black granite chips with R.C.C man hole cover, earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering,curing,cost of all materials, conveyance of all materials to worksite, payment of royalty,all taxes etc.all complete as per approved drawing, P.H specification and direction of Engineer-in-charge Inside size : 760mmx760mmx460mm

Supplying all materials ,labour ,T&P and constructing Man Hole Chamber of inside size 910mmx910mmx910mm with cement concrete (1:3:6) using 40mm size crusher broken hard black granite metal on bed , KB brick work in cement mortar (1:6) in foundation and plinth, moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips, 12mm thick cement plaster (1:3) with cement punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab (1:2:4) using 12mm size crusher broken black hard granite chips with R.C.C man hole cover, earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering,curing, conveyance of all materials to worksite, payment of royalty, taxes etc.all complete as per approved drawing, P.H specification and direction of Engineer-in-charge Inside size : 910mmx910mmx910mm

Excavation of foundation in laterite rock or any hard rock (other than granite or disintegrated rock) removed by chiselling including dressing and levelling the bed not exceeding 1.50 mtr. in depth and depositing the soil within initial lead of 50 mtr. and as per specification approved by the Department.

Supplying all materials, labour, T&P & constructing Soak Way Pit of the following size with dry brick walling from bottom upto invert of inlet pipe and KB brick work in cement mortar (1:6) for the remaining height at top, cement concrete (1:4:8) using 40mm size crusher broken hard black granite metal on bed, 12mm thick cement plaster in cement mortar (1:4) inside and outside over masonry brick work, gravel backing in the rear of well steining, RCC cover slab in cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips fitted with iron lifting handles including earth work in open well excavation in all kinds of soil and refilling of cavity around the pit and painting the iron works, watering, curing,cost of all materials,conveyance of all materials to worksite, payment of royalty, all taxes etc. all complete as per approved drawing,PH specification and direction of the Engineer-in- charge. 1.20m dia x 2.00m deep inside size Soakway Pit

Supplying all materials ,labour ,T&P and constructing gully trap chamber of inside size 250mmx250mm with 8cm thick RCC precast cover slab in cement concrete (1:2:4) mix using 12mm size crusher broken HG chips, foundation concrete (1:4:8) using 40mm size crusher broken HG metal on bed and around trap, KB brick work in cement mortar (1:6) in foundation and plinth and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap, 150mmX150mm size CI grating etc.all complete as per drawing, specification and direction of Engineer-in-charge. In side size 250mmx250mm

Supplying all materials,labour,T&P and laying in trenches ( to level or slope ) unplasticized PVC pipe conforming to IS:4985/2000 of the following outside dia for class-3 (0.60mpa) including jointing with supply of approved solvent cement by non-heat application method/ as per manufactures's providing and laying in trench cement concrete(1:4:8) with 40 mm size hard granite metal in the Type-C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer-in-charge. 110mm dia U-PVC pipe ( Allround concrete )

Supplying all materials, labour, T&P and providing cement punning including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.30m in depth and as per direction of the Engineer-in-Charge.

Extra lifts of 1.50 mtr or part thereof over the initial lift of 1.5 mtr in all kinds of embankments and road works and ordinary earthwork in general. 1x6.10x2.70x0.30

Supplying all materials, labour, T&P and providing M.S reinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and filling in foundation and plinth with sand well watered and rammed including conveyance of all materials to worksite, payment of royalty, taxes etc.all complete as per direction of the Engineer in charge.

Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 4cm size hard granite metal including watering, curing, conveya

Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

nce of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and making MS step iron in 20mm diameter MS steel bars and fixing into walls of man hole/septic tank duly embedded in cement concrete (1:3:6) complete as per specification and direction of the Engineer in charge.

Filling in foundation and plinth with excavated materials, moorum including watering and ramming as directed by the Engineer in charge

Supplying all materials, labour, T&P and providing 6mm thick cement plaster (1:4) on RCC work including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge R.C.C floor and roof slabs up to 4.30m height

R.C.C beams,columns,girder and bressmer etc.

Supplying all materials, labour, T&P and providing cement concrete (1:1.5:3) with 12mm size hard broken granite chips for R.C.C works including hoisting, laying, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard broken granite chips including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing brick work with Fly ash bricks having crushing strength not less than 75kg/cm² with dimensional tolerance ± 8 percent in cement mortar (1:4) including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge In F&P

Supplying all materials, labour,T&P and providing 25mm thick grading concrete (1:2:2) on roof slab with 6mm size hard granite chips on new work including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing shoring and shuttering foundation trenches, pits etc with close wooden planks or sheets shuttering etc all complete as per direction of the Engineer in charge.

Dewatering with 5 H.P diesel engine pump during excavation

Supplying all materials, labour, T&P and fitting and fixing S.W.Tee of size 150mx150mx150m as per P.H.D.specification and direction of the E.I.C.

Supplying all materials, labour, T&P and constructing vent base as per P.H.D specification etc all complete.

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the engineer in charge. 110mm diameter U-PVC SWR pipes(Supreme/Ashirvad/Oriplast)

110mm U-PVC cowl

Supplying fitting and fixing 30mm thick Solid panel PVC door shutter consisting of frame made out of MS tube of 19 gauge thickness and size of 19mmx19mm for stile & 15mmx15mm for top and bolt rails set with PVC door frame(Choukatha)of size 50mmx47mm is made out of 5cm thick sheet properly joined with solvent cement adhesive as per section view with MS square tube of 19mm of 19mm gauge to be inserted inside to give extra structural strength the price is inclusive of all cost of all materials labour,T&P etc.complete in all respect as per direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and providing fitting and fixing (Aqua guard) Pure Chill 80 PSS RO+UV of size 750x570x1350mm height with water storage capacity 80 liters along with 2 nos of faucets 1 for cold water and 1 for normal water including a flow of 1.5 ltr per minute etc all complete as per approved drawing,specification and direction of the Engineer in charge.

Supplying all materials,labour,T&P and setting up boring equipments including erection of suitable staging for installation of the required size of tube well,dismantling and removing the same after completion of the work including transportation of the boring equipments,cleaning and leveling the site,excavation of mud pit,channels etc.leveling of site all complete as per direction of Engineer-in-charge

Supplying all materials,labour,T&P and transporting the boring pipes,top casing grouting pipes and fittings,PVC pipes and well screens etc.to the worksite including loading and unloading etc. all complete as per direction of Engineer-in-charge

Supplying all labour,T&P and drilling pilot bore not less than 102mm dia. without casing pipes in all kinds of soils and rocks for the following depths excluding supply of necessary cutting equipments,extra sockets (whenever required ) etc. and withdrawing the boring pipes,washing and keeping the bore clean for logging if required all complete as per direction of Engineer-in-charge Labour for drilling pilot bore from 0 to 360 mtr labour charges

Supplying all labour,T&P and reaming the pilot bore to following sizes and depths without casing pipes including withdrawing the boring pipes,washing the bore by means of pipe cylinder etc. all complete as per direction of Engineer-in-charge Reaming 100 mm dia. to 150 mm dia.

Reaming 150 mm dia. to 200 mm dia.

Reaming 200 mm dia. to 250 mm dia.

Supplying all labour,T&P and jointing materials and lowering the 300mm dia top casing pipes into the position and removing the same after use all complete as per direction of Engineer-in-charge

Supplying all labour, tools and plant and jointing materials and lowering the pvc casing pipes, fittings and well screens in position including fitting and fixing of centraliser, cutter plug and washing the bore etc complete as per the direction of the Engineer in charge

Cost of 150mm Dia casing Pipe

Cutting slots in 150mm dia Pipe

Cost of 150mm dia end plug

32mm dia steel short piece

Cost of 150mm dia cap

Supplying all materials,labour,T&P and packing the bore with washed gravel (size p-6 )of around the pipes in good quality excluding cost of gravel etc. all complete as per direction of Engineer-in-charge

Supplying all materials,labour,T&P and materials for cleaning and developing the tube well with compressor continuously washed till clean and adequate discharge is obtained from the tube well including supply and use of necessry equipment and labour complete in all respect as per the direction of the Engineer-in-Charge.

Supplying all materials, labour, T&P and providing fitting & fixing submerssible pump with squirrel cage induction type submerssible electric motor to run single-phase line voltage ranging from320 to450 volt confirm to IS 8034/89 with following specification suitable control pannel jointing with GI/PVC/HDPE pipe, electrification, testing, commissioning , trial running, conveyance of all material to work site, payment of all taxces etc all complete as per PH specification and direction of Engineer-in-charge. 1 H.P single phase 3 stage head range 20 to 35 metres, discharge 145 to 110

DOL contol pannel suitable for 1HP pump