Reddiyarchatram2_2024

Amount

Earthwork excavation for foundation in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary, refilling the foundation with excavated earth and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of 2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers.

Earthwork Open excavation in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary refilling the foundation with excavated earth other than sandy soil in layers of not more than 15 cm thick layers well rammed and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of 2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers.

Refilling basement with excavated earth other than sand with an initial head lead of 100 mts. and depositing the earth as shonw by the departmental officers in layers of not more than 15cm thick well rammed, watered and consolidated etc. complete complying with standard specification.

Supplying and Filling in foundation and basement with filling M sand in layers of not more than 15cm thick well rammed watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and Filling in foundation and basement with gravel in layers of not more than 15cm thick well rammed watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling of 40mm HBGS metal in dispersion trench around the stoneware pipe or in the leach pit or rain water harwesting pit or soak pit to the required thickness as directed by the departmental officers etc. complete. (The rate including cost of metal filling etc. complete complying with standard specification.

Supplying and filling of 20mm HGBS metal in dispersion trench around the stoneware pipe or in the leach pit or rainwater harwesting pit or soak pit to the required thickness as directed by the departmental officers etc. complete. (The rate including cost of metal filling etc. complete complying with standard specification.

Cement concrete 1:5:10 (one cement, five M-sand and ten aggregate) using 40mm gauge hard broken blue granite stone jelly for foundation and basement including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification and as directed by the departmental officers.

Plain Cement concrete 1:2:4 (One cement two m-sand and four aggregate) using machine crushed 20mm gauge hard broken granite stone jelly excluding cenetering, shuttering and, but including laying, curing and finishing etc., complete complying with standard specification and as directed by the departmental officers.

Foundation and Basement

First Floor

Second Floor

Third Floor

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) For column footing plinth beam etc.

Supplying and erecting steel centering including necessary supports for plane surfaces, for all RCC works including strutting upto 3.29m in all floors using mild steel shutters of size 90cmx60cm of BG 10 stiffened with mild steel angles of size 25mmx 25mmx3mm laid over silver oak (Country wood) Joists of size 10cmx6.5cm spaced at about 90cm c/c and supported by casurina props of 10cm to 13cm dia. (spaced at 75cm c/c) etc., complete complying with standard specification and as directed by the departmental officers. (The centering will be removed after specified period of concrete without damaging the concrete)

For plain surface such as RCC floor slab, roof slab, beam litels bed blocks, landing slab, waist slabs and beams, etc.,

For plain surface such as rectangular or square RCC columns, sunshdes, top and bottom slab of RCC, etc.,

For plain surface such as Vertical surfaces such as sunshade, boxing vertical drops, facia for sunshade and other vertical walls etc.,

Providing additional strutting using casurina poles to centering of RCC slabs or plane surfaces for every addtional 1 metre height or part there of but not less than 30cm over the initial height of 3m from floor level using casurina props of 10cm to 13cm dia including cross bracings etc., complete complying with standard specification and as directed by the departmental officer.

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance using with IS:456-2000, 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of M sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation & Basement

For Super structure in Ground Floor

For Super structure in First Floor

For Super structure in Second Floor

For Super structure in Third Floor

Supplying, fabricating and placing in position of steel reinforcement using MS (or) RTS rods for all RCC item of works including cost of steel and binding wire in all floors etc., complete complying with standard specification and as directed by the departmental officers.

Brick work in cement mortar 1:5 (one cement and five M sand) using Third class kiln burnt country bricks of size 8 3/4 ”× 4 1/4 × 2 3/4” including curing etc., complete complying with standard specification and as directed by the department officers. (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost).

For Foundation & Basement

Brick work in cement mortar 1:6 (one cement and six M sand) using Third class kiln burnt country bricks of size 8 3/4 ”× 4 1/4 × 2 3/4” including curing etc., complete complying with standard specification and as directed by the department officers. (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost).

For Foundation & Basement

For Super structure in Ground Floor

For Super structure in First Floor

For Super structure in Second Floor

For Super structure in Third Floor

Damp proof Course with Cement Mortar 1:4 (One cement & four M sand) 12mm thick mixed with water proofing compound of approved quality confirming to ISS @ 2% by weight of cement used etc complete complying with standard specification and as directed by the departmental officers.

Brick work partition wall 10.80 cm thick using using Third class kiln burnt country bricks of size 8 3/4 ”× 4 1/4 × 2 3/4” in cement mortar 1:3 (One cement and three M sand including fixing hoop iron reinforcement if found necessary, laying, finishing and curing etc., complete complying with standard specification and as directed by the departmental officers.

For Super structure in Ground Floor

For Super structure in First Floor

For Super structure in Second Floor

Supplying and Fixing New Cuddappah slab fine polished of approved quality of 38 / 40mm thick including cost of cuddappah slab for cupboards, transportation to work site, labour charge for forming grooves in masonry if necessary and laying the slab in position with cement mortar 1:3 (One cement and three m-sand) etc., complete complying with standard specification and as directed by the departmental officers.

Manufactureing, supplying and Fixing RCC precast slab of 50mm thickness in reinforced cement concerete 1:2:4 (One of cement, two of sand and four of aggregate) using 20mm hard broken stone jelly and river sand, excluding the cost of reinforcement grills and including fabrication charges, moulding, curing, finishing charges and fixing in position neatly etc., complete complying with standard specification and as directed by the departmental officers.

50mm thick

75mm thick

Supplying and fixing of special type Terra Cotta Jally of size 20x20x8cm of approved pattern including pointing neat finishing and labour charges for fixing the jally in position etc., complete complying with standard specification and as directed by the departmental officer.

Fabricating supplying and fixing in position CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames of section size 105mmx60mmx1.25mm thick with necessary rebate of size 35x15mm for housing door shutters conforming to IS specification. Frames shall be fabricated to the specified door size with joints properly welded and grinded. Stiffeners with 25x3mm MS flat shall be provided around the frame at 60cm intervals. The cost shall also include for providing 3 Nos. of MS clamps with 25x3 flats each on either sides of door frame, providing bottom tie, with 10mm dia MS rod, providing necessary holes for receiving tower bolts 2 Nos. with stiffeners on inner side, providing the required number of I.O hinges of size 125x30mm for shutters properly welded to the frames, finishing the door with one coat of good quality red oxide primer with cement concrete 1:2:4 (One cement, two M sand and four aggregate) using 20mm gauge hard broken granite stone jelly packed inside to the frame including cost of all materials, fabrication and conveyance to the site and fixing in position with necessary scaffolding etc., complete complying with standard specification and as directed by the departmental officer.

Supplying and fixing in postion of 35mm thick solid core flush door shutters with following specification. with Commercial ply on both sides and with TW lipping of size 35x12mm on all edges with necessary adhesives and C.P. Screws Alu. Butt Hinges (6 nos. 250 x 16 mm Size) Alu. Aldrop1 No. 250 x 16 mm Size, Alu. Tower Bolt 2 No. 250 x12 mm size, alu. Tower Bolt 2 No. 200 x 12 mm size, D type alu. Handle 200mm length 2 No., alu. door stopper with rubber bush 2 No. shall be provided, as directed by the departmental officers etc., complete.

Single Leaf

Double Leaf

Supply and Fixing of M.S. steel doors with Single Leaves following specification. MS angles of size 40x40x 6mm at 3.5 kg/m used for the outer frame and MS angles of size 35x35x5mm at 2.60 kg/m for the shutter frames. Stiffners with 32x6mm at 1.50 Kg/m. MS flat is provided as the lock rail of the door and welded infact of both ends to the shutter frame, 18 gauge CR sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50 Kg / RM and MS flat on the rear side of the door sandwitching the CR sheet for rigidity with locking rail and bottom tie arrangements. Additional stiffners with 18x5 mm at 0.7 kg/m MS flats are provided horizontally diagonally on the rear side of the shutter. 2Nos of hinges in case of single leaf and 4Nos of hinges in case double leaf shutter is provided 6 Nos of hold fasts 200 length 40x40x6mm M.S. angle spliced at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. one at top and the other at bottom are provided. One aldrop is provided incase of double leaves door at lock rail section in the door. For single leaf doors, one more aldrop is provided in the inner side at the lock rail section of the door.

Supplying and fixing in position of Solid PVC door shutters using 19 gauge 19mm MS square tubes for styles and outer frames 15mm M"S square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mmx30mm. The over all size of top rail, lock rail and bottom rail shall be 75mmx30mm. The over all size of frames shall be 50mmx45mm with suitable rebate for housing the shutter with frame.

Supplying and fixing in position of PVC Sliding Door with roller using 19 gauge 19mm MS square tubes for styles and outer frames 15mm M"S square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mmx30mm. The over all size of top rail, lock rail and bottom rail shall be 75mmx30mm. The over all size of frames shall be 50mmx45mm with suitable rebate for housing the shutter with frame.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing MS grills to doors, windows and ventilators etc. using necessary MS flats (or) square rods for inner members and outer members which should be fixed to window frames as directed and design given by the departmental officers inclusive of cost of providing one coat of best quality red oxide primer etc., complete complying with standard specification and as directed by the departmental officers .

Manufacturing, Supplying and fixing Stainless Steel hand rail for staircase using 50mm dia 304L Grade stainless steel pipe of 1.60mm thick at at required locations to a height of 1000mm from finished floor level welded to 38.30 mm dia stainless steel pipe post of 1.00mm thick as vertical at 900 center with 3nos of 25.40mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100x100x6mm MS base plate encased in the base concrete. The rate is inclusive of charges for cutting , bending , welding , grinding polishing conveyance, electrical charges , etc., complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for toilets of Differentially abled person using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Finishing the top roof with one course of solar reflecting ceramic tiles of size 305x305x7mm thick of approved quality set in cement mortar 1:3 (One cement and three sand) (12mm thick ) and mixed with for 10M2 / 4.00 kg Epoxy Packing conforming to ISS including curing etc., complete complying with standard specification and as directed by the Departmental officers.

Lime Concrete 1:2:5 (One lime, two M sand and five brick jelly) using 20mm gauge brick jelly for flooring and toilet depression filling etc., including laying, consolidating, finishing, rendering the top surface rough to receive the floor finish, curing, etc., complete complying with standard specification.

Special ceiling plastering in all floors and finishing the exposed surface of RCC items of work such as slab, beam, sunshade, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (One cement and three P-sand) 10mm thick with Bonding agent Cebex112, Zydex- Zycrete 2X or other Equalent compound conforming to BIS at 200 ml of one cement bag (50kg) for increased workablity and air entrainment including hacking the surfaces and providing cement mortar nosing, beading for sunshade, staircase, step, landing slab etc., including neat finishing and curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with cement mortar 1:5 (one cement and five P-sand) 12mm thick mixed with Bonding agent Cebex112, Zydex- Zycrete 2X or other Equalent compound conforming to BIS at 200 ml of one cement bag (50kg) for increased workablity and air entrainment used finishing in all floors using fine P sand including neat finishing, curing, etc., complete complying with standard specification and as directed by the department officers.

Plastering with cement mortar 1:3 (one cement and three P sand) 12mm thick with WPC 2% by weight of cement with Bonding agent Cebex112, Zydex- Zycrete 2X or other Equalent compound conforming to BIS at 200 ml of one cement bag (50kg) for increased workablity and air entrainment used in all floors using fine Psand including neat finishing, curing, etc., complete complying with standard specification and as directed by the department officers.

Supplying and fixing in position best approved of ISI quality of following dia PVC rain water down fall pipes having a working pressure of 4 kg / sq.cm including cost of necessary PVC shoe, PVC bend, C.I. gratings of required dia. and special clamps, brass screws, nails etc., and fixing of cast iron gratings at juction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable iron grating. The PVC pipe shall be fixed on wall with special type of clamps. Special type "U" clamp at the centre of the pipe line shall be fixed in addition to those for more than 3.0M pipe length complying with standard specification.

160 mm dia

110mm dia

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with Stain free nano polished vitrified tiles (like Marbonite or equivalent) of approved quality and colour of size 600 x 600x 8 mm thickness in all floors over a base layer of cement mortar 1:3 (one cement and three M sand) 20mm thick and pointing with white cement using 0.30kg/m2 including adding suitable colour pigments to suit the colour of tiles finishing perfectly and curing etc., including cost of tiles, all materials and incidential charges, transportation charges and labour charges for laying tiles etc., complete complying with standard specification and as directed by the Departmental officers. (The tiles should be got approved by the Departmental officers before use on works).

Paving the floor with Tactile paver type of new tack BT yellow colour ceramic tiles of approved quality and colour of size 305 x 305 x 15mm in all floors over a base layer of cement mortar 1:3 (one cement and three M sand) 20mm thick and pointing with white cement using 0.30kg/m2 including adding suitable colour pigments to suit the colour of tiles finishing perfectly and curing etc., including cost of tiles, all materials and incidential charges, transportation charges and labour charges for laying tiles etc., complete complying with standard specification and as directed by the departmental officers . (The tiles should be got approved by the departmental officers before use on works).

Paving the floor with Anti skid colour and Design ceramic tiles of size 305x305x6mm of approved quality and colour of size 305x305x6mm for flooring in all floors over a base layer of cement mortar 1:3 (One cement and three m sand) 20mm thick and pointing with white cement using 0.30 kg of white cemenbt per square metre including adding suitable colour pgments to suit the colour of tiles finishing perfectly and curing as directed by the departmental officers including cost of tiles, all materials and incidental charges, transportation charges and labour charges for laying tiles as directed by the departmental officers complete complying with standard specification. The tiles should be got approved by the departmental officers before use on work.

Dadooing the walls with colour design glazed tiles of size 300mmx 450mmx 8mm of approved quality in all floors set in cement mortar 1:2 mix (one cement & two M-sand) 10mm thick and pointing with white cement using 0.4 kg/m2 including adding suitablee colour pigments to suit the colour of tiles including finishing the joints neatly and curing etc.,complete complaying with standard specifications. (The tiles should be got approved by departmental officers before use on the work).

Supplying and fixing of PVC corner beading of best approved quality and colour standard size and thickness of required height of walls using cement mortar 1:2 (One cement and two M sand) and finishing the surface smooth with ceramic tiles etc., complete complying with standard specification and as directed by the departmetal officers.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed.

Painting the walls two coats with best Oil bound distemper of approved quality (to be approved by the Executive Engineer before use on works) over one coat of primer for newly plastered wall including preparation of surface and finishing neatly including cost of all materials, brushes, scaffolding charges etc., complete complying with standard specification and as directed by the departmental officers.

Painting the exterior walls surface two coats of best and approved first quality and colour of Exterior emulsion paint in all floors over one coat of primer including preparation of surface, wall putty two coats with good quality including cost of wall putty , emmary sheet, plates, etc. and including labour charges for rubbing the wall scrapping putty pasting works and making good smooth surface and finishing neatly etc., . complying with standard specification and as directed by the departmental officers etc. complete. ( The make, quality and colour of paint should be got approved by the departmental officer before use of work)

Supplying and painting the walls with two coats of cement paint over one coat of cement primer including preparation of surface curing complete in all floors etc., complete complying with standard specification and as directed by departmental officers (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Painting the new wood work two coats with best approved first quality and colour of synthetic enamel paint over a priming coat of approved quality in all floors including cost of paint, labour and other materials like brushes, putty and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officers. (The make quality and colour of paint should be got approved by the departmental officer before use on work).

Painting the new iron work with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat and including cost of painting materials, brushes, putty, preparation of surfaces and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officer. (The quality and colour of paint should be got approved by the departmental officer before use on work).

Providing expansion joint of 20mm width in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non - absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

Providing expansion joint of RCC floor slab for 20mm width using polysulphide as sealent on top and bottom for a depth of 7.5mm each and packing the inner space using compressible non - absorbent, filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed.

Providing expansion joint of 20mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non - absorbent, flexible and well compressible filler materials of approved quality and covering top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed.

Providing Anti – termite treatment to soil adjacent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 part I to IV in stage to suit the progress of work consist as per the detailed specification as below (Measurements taken for the plinth area for the purpose of payment) including braking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport & storing etc., complete and as directed by the departmental officers.(The chemical should be got approved by Executive Engineer before use on work). Stage -1 : Spraying Anti –termite chemical solution for the foundation before laying concrete, in bottom and sides of foundation. Stage-2 : Spraying Anti –termite chemical solution to the grade beam level, spraying has to done for to grade beam brick masonry contact with the back fill earth. Stage-3 : Spraying Anti –termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out and sand filling by making holes with crow bar to a depth of 60cms and at 60cms intervals on both direction and at junction of wall and flooring throughout. Stage -4 : Spraying Anti –termite chemical solution alround building outside by making holes with crow bar before laying plinth protection and the holes to be close after the treatment.

Supplying and installation of Ceramic Steel chalk writing board with the following specification. The 2mm GI Sheet is placed with wall side over the GI sheet necessary adhesive is spreaded and fixed the 9mm MDF board on the GI sheet 0.40mm thick ceramic steel chalk board is provided over the MDF board and the whole arrangements are fixed to the frame using heavy anodized Aluminium section and Chromium plated provided in the corners. The whole arrangement are fixed to the wall using wooden plugs and screws etc., The rate includes all above materials, labour charges and taxes etc., complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) powder type fire extinguisher of 6 kg capacity as per IS:15683with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc. including conveyance, all incidential charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc. complete as per standard specification and as directed by the Departmental Officers. Make: Excellent/Safety First/equivalent.

Supply and fixing of carbon-di-oxide gas type 2 kg. capacity Fire extinguisher as per new IS:15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc. including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc. complete as per standard specification and as directed by the Departmental Officers. Make: Excellent/Safety First/equivalent.

Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm.

Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames. Glass: 5mm reflective Saint Gobain OR equivalent

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact complete and complying with standard specification and as directed by the departmental officers.

Supplying and fixing ornamental Brass-in-lay Burma Teak Wood Entrance Door with a size of 2.10 m x 2.55m with six leaves as per the drawing and design as approved by the departmental officers.The clear opening of each door shall be of 2.00m. The outer frames are of finished size 175mm x 125mm.The Each door shall have two leaves of 1/3 panelled and 2/3 glazed. The Outer frame of the shutter of finished size of 150mm x 50mm.All the Panels shall be of finished 50mm thick. The main outer frame, shutter frame and panels shall be engraved with computer design ornamental carving works of approved pattern with skilled carpenter as directed by departmental officers. All the glazing works shall be done with design painting works.Necessary grill protection arrangements shall be made for the glass portion. The door frame and shutters shall given two coats of best and approved quality of high Glossy Polyurethane finish.The rate includes cost of best and approved quality of Burma Teak wood,design painted glass, Brass hinges,Tower bolts, Aldrop, locking arrangments,ornamental handles,brass screws and labour charges, transportion charges, all taxes, etc., complete.

Supplying and fixing in position Indian water closet oriya type of size 580x440mm white glazed earthernware of approved quality with 'P" trap or 'S' trap conforming to IS 2556-Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to PVC. pipes by dismantling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specification and as directed by the departmental officers.(The Oriya type Water Closet and all accessories should be got approved by the departmental officers before use on work)

Supplying and fixing in position White Glazed European water closet of best quality and approved make with 100mm P or S trap with double flapped rigid PVC.seat cover with chromium plate brass hinges, including supplying and fixing PVC. Low level flushing tank 10 litre capacity of approved quality on wall with teak wood plugs, brass screws and 2 numbers 15mm dia gun metal wheel valve, 15mm dia nylon connection and giving necessary water supply connection as directed by the departmental officers. The rate includes cost of 100mm dia PVC.Pipe 60cm long including cost of 3 Kg.of white cement 6Kg.of cement, spunyarn, shellac, thread ball, teak wood plugs, brass screws 75mmx10mm etc., complete complying with standard specification and as directed by the departmental officers. (The European Water Closet and flushing tank should be got approved by the Departmental Officers before use on work.)

Supply& fixing SS health faucet of best quality with control valve etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position PVC Nahini trap of size 110x75mm with best pvc gratings of approved brand and quality with fixed over a bed of brick jelly lime concrete 1:2:5(one part of lime,two parts of sand and five parts of 40mm size brick jelly)and finished with cement Mortar 1:3(one cement and three sand)including dismantling masonry works wherever found necessary and making good the damaged portions to the original condition giving connections to the pipe etc., complete complying with standard specification and as directed by the departmental officers. (The PVC Nahini trap with grating should be got approved by the departmental officer before use on works).

Supplying and fixing in position best quality of approved make white glazed earthernware wash hand basin (without pedestal) of size 550x400mm with a pair of cast iron brackets , including cost of 15mm diametre brass chromium plated pillar tap, 32mm diametre C.P.waste, 32mm diametre PVC waste pipe with rubber plug and chain, 15mm diametre gun metal wheel valve, 15mm dia brass nipple, 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with pair of C.I.brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anti-corrosive paint including testing for leakage etc., complete complying with standard specification and as directed by the departmental officers.(The wash hand basin and specials should be got approved by the departmental officers before use on work)

Supplying and fixing in position of Indian make white glazed earthen ware lipped mouth flat back Urinal of best approved quality with 32mm dia bell mouthed PVC connection,15mm dia G.M wheel valve,fixing the Urinal to the wall in position with necessary T.W. plugs,clamps,screws shellac etc.,including dismantling masonry if necessary and redoing the same to original condition,fixing the 15mm GI pipe connection and wheel valve, painting the pipe with two coats and checked without any leakage etc., complete complying with standard specification and as directed by the departmental officers.(The urinal should be got approved by the departmental officers before use on work)

Supplying and fixing in position of polished white marble slab (Adanga) of 20mm thick for urinal partition of size 1.20x0.60m including and fixing the marble slab with C.M.1:3 etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed porcelain sink of size of 600 x 450 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Supplying and fixing PVC Ventilating shaft of 110mm dia (having working pressure 4 kg / sq.cm) and 3 m height including cost of cylindrical cowl of best approved quality etc., complete complying with standard specification and as directed by the departmental officers. The PVC ventilating shaft should be got approved by the departmental officers before use on work.

Supplying, laying and jointing 150mm dia glazed stoneware pipes of approved brand and quality with spigot and socket ends in dry conditions of stoneware pipe with water tight joints with necessary earthwork excavation to the required depth with spunyarn and loose joints laying in true alignment and gradient and conducting required water test with necessary tools and plant etc.,complete complying with standard spcification and as directed by the departmental officers. (The Stone ware pipe should be got approved by the departmental officer before use on works).

Supplying, laying and jointing PVC soil / waste pipes of approved and best variety conforming to IS. Specification with ISI. mark of the following sizes including, cutting and threading of PVC Pipes, fixing specials but excluding cost of such specials but including fixing to wall with necessary teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in roof and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges. The PVC Pipes should be got approved by the Departmental Officers before use on work. Below ground level.

75mm dia PVC pipe

110mm dia PVC pipe

160mm dia PVC pipe

Supplying and fixing in position of the following PVC specials best approved quality conforming to ISS and providing leak proof joints with PVC adhesive etc., i and giving connections to the PVC pipe etc., complete complying with standard specification.(The PVC specials should be got approved by the departmental officer before use on works).

160mm PVC 'Y'

160mm PVC Plain elbow

160mm PVC door elbow

160mm PVC cowl

110mm PVC Door 'Y' (Double)

110mm PVC Plain elbow

110mm PVC door elbow

75mm dia PVC Door 'Y' (Single)

75mm dia PVC Plain elbow

75mm dia PVC bend

75mm dia PVC cowl

160mm dia PVC Tee

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) with necessary earth work anf refilling charges the earthwork and refilling charges shoul be paid seperatly, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. For External Water supply arrangements. (Below Ground Level)

50mm dia UPVC pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs,UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. For External Water supply arrangements. (Above Ground Level)

50mm Dia UPVC Pipe

40mm Dia UPVC Pipe

32mm Dia UPVC Pipe

25mm Dia UPVC Pipe

20mm Dia UPVC Pipe

Supplying and fixing in position 15mm dia Chromium Plated screw down Taps (heavy type) of best quality and approved make conforming to ISS and providing leak proof joints with thread and shellac etc., including fixing and connecting to the pipes etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the departmental officer before use on work)

Supplying and fixing in position UPVC specials such as plain bend and shoe of various sizes of best approved quality conforming to ISS.and providing leak proof joints including fixing to wall and giving connection to the UPVC. Pipes including,dismantling the brick masonry/RCC.floor or roof slab and redoing the disturbed portion to original condition etc.complete as directed by the Deptl.Officers complete complying with standard specification

50mm UPVC Tee

50mm UPVC Union

50mm UPVC hex nipple

50mm UPVC Coupling

50mm dia UPVC Elbow

40mm UPVC Tee

40mm UPVC Union

40mm UPVC hex nipple

40mm UPVC Coupling

40mm dia UPVC Elbow

32mm dia UPVC elbow

32mm dia UPVC Tee

32mm dia UPVC Union

32mm UPVC hex nipple

32mm dia UPVC coupling

32 x 25mm dia UPVC reducer elbow

25mm dia UPVC Elbow

25 x 20mm dia UPVC reducer Tee

20 x 15mm dia UPVC reducer Elbow

Supplying and fixing in position best quality and approved variety of new Gun Metal Gate Valve / Wheel Valve heavy type excluding the fixing charges but including necessary cutting & threading of GI pipes for jointing the GI specials and providing two coats of painting with good quality and approved variety of anti-corrosive paint over a coat of red oxid primer coat in the case of pipe line above ground level and one coat of tarring in the case of pipe line below ground level etc., complete

40mm dia wheel Valve

32mm dia wheel Valve

Supplying and fixing in position of Man hole cover with frames of size 600x600mm (Heavy Duty) of best approved quality and as per Indian standard specification make etc., complete complying with standard specification and as directed by the departmental officers. (The Man hole cover should be got approved by the departmental officers before use on work).

Drilling of borewells of size 6" to 8" dia. in sedimentary formation using hand boreset including insertion of casing pipe etc., and supplying and packing of pebbles (Conveyance of hand bore set including loading and unloading to be done by the contractor)

Drilling bore well upto 60m (110mm dia)

Suppling of new special blue PVC pipe for bore well of approved quality and verty confirming to IS 4985 with ISI mark of the following size and standard length including cost of pipe transprotion to work sites cutting threading jointing labour charges for erection as directed by the departmental office complete complying with standard specification

110 mm dia Special blue slotted pipe

Supplying and fixing 300 mm dia RCC Hume pipe pressure non spun pipe with socket and spigot end as per IS 458/2003 manufactured with sulphate resistance cement with 12 mm HI- alumina lining with rubber ring joint.

Providing cupboard shutter using termite/water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc. as directed by the departmental officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer before use on work.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Jet Black and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 16/ 18mm thick of flamed steel grey granite and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Labour charges for finishing the top of working tables and staircase step portion with nosing arrangements in Granite slab tiles including cutting the edges and polishing including cost of polishing materials complete complying with standard specification and as directed by the departmental officers.

Labour charge for grooving the granite slab for staircase step portion including cutting the edges and polishing including cost of polishing materials etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and laying of 63 mm thick high strength type of interlocking rubber moulded hydraulic pressed paver block of approved colour made up of designed concrete mix 1:1:2 using 10 to 12mm size HBG stone jelly in required shapes and sizes having minimum compressive strength of 40 N/mm2 to be laid in flurrying bone pattern with approved non sticking surface at top. The rate is inclusive of levelling the site, compacting with power compactor and sweeping the sand grouting and also inclusive of transportation charges, loading, unloading and labour charges for laying the paver block, etc. complete and as directed by the departmental officers

Drilling of Borewells anywhere in TamilNadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the departmental Officers) including construction of mud pit.

up to 60m depth below ground level

from 60m to 90m

from 90 m to 120m

from 120m to 150m

from 150m to 180m

Reaming 140/150 mm dia pilot bore to 300mm dia bore as directed by the departmental Officer

up to 60m depth below ground level

from 60m to 90m

from 90 m to 120m

from 120m to 150m

from 150m to 180m

Charges for developing the Borewell with air compressor of 600 CFM capacity (Minimum 8 Hours) including transportation, labour and fuel charges for compressor as directed by departmental Officers and conducting yield test by 'V' notch method.

Supply of 150mm dia PVC special casing pipe without slot of best approved quality having pressure of 6 kg/sq.cm. etc., complete as directed by the departmental officers. The pipe should be got approved by the Executive Engineer before use on works.

Supply of 150mm dia PVC special casing pipe of best approved quality having pressure of 6 kg/sq.cm. etc., complete as directed by the departmental officers. The pipe should be got approved by the Executive Engineer before use on works.

Labour Charges for inserting PVC Casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC Couplers with Cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the departmental officer

Supply and fixing of 160mm dia PVC End cap of best approved quality having pressure of 6 kg/sq.cm. etc. complete as directed by the departmental officers. The pipe should be got approved by the departmental officer before use on works.

Supplying and erecting 10.00 H.P 3 phase submersible pump with DOL starter, 3 phase panel board of approved make conforming to ISI.including cost of all accessories, transportation charges, labourcharges for erecting and fixing the motor in position testing as directed by the Departmental Officers complete complying with standard specification. The quality and standard of product should be got approved by the Departmental Officers before erecting. Necessary warranty card should be produced before erection of Motor.

Supplying and fixing of 3 x 6 sq.mm PVC insulated and sheated 3 core flat type copper cable confirming to IS 694/1990 etc., complete complying with standard specifications.

Suppling and delivery of best and approved quality of 50mm dia HDPE pipe of 10kg/m2 size including laying in the basement and tying with copper wire etc., complete complying with standard specification for delivery line from the bore from submersible pump in borewell and as directed by the departmental officer.

Supplying and tying of Nylon rope of 18mm dia thread make with best quality for holding submersible pump etc., complete as directed by the Executive Engineer. The Rope should be got approved by the Executive Engineer before use on works.

Supplying and Fixing of PVC ready made water tank of approved quality with standard specification and best brand including testing for leakages after making installations and connections. The cost inclusive of lid and lock with bolt and nuts for PVC tank, transportation, loading, unloading, lifting, installation and necessary connections etc., complete complying with standard specifications and as directed by the departmental officers.(The PVC Water Tank should be got approved by the Executive Engineer before use on works).

Finishing the top of flooring with granolithic floor finish of 25mm thickness with plain cement concrete of mix 1:2:4 (One cement, two M sand and four aggregate) using 20mm / 10 to 12mm ISS gauge hard broken granite stone including finishing the top smooth and forming thread lining and curing etc., complete complying with standard specification and as directed by the Departmental officers

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 2.40 mx 2.40 m.The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 4 mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 No., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Supplying and fixing of Hylem sheet 3mm thick for expansion joint etc., complete complying with standard specification and as directed by the Departmental officers

Supplying and fixing of Incinerator for Ladies Toilet etc., complete complying with standard specification and as directed by the departmental officers.

Providing mixing laying polymer based water proofing treatment for the sunken toilet by applying cement based fiexable WPC conforming to IS 2645 to a thickness of 1mm of the prepared surface of the roof slab / floor slab as per specification mendioned above providing cm 1:3 water proofing cover plaster to a thickness 12mm. The malaime coating with admixture of approved make rate quoted is inclusive of preparation of surface which including cleaning of surface polymer morter, curing, labour, tools equipments etc., rate inclusive of cement and sand required for the treatment the coat and labour charges for fixing 25mm dia pressure pipe 15 kg / m2 to length of 45 cm for drip pipe etc., complete.

Sub Total

P KALIKURICHI (BID ID -1118445)

VMSI Construction (BID ID -1118510)