PROVN OF CERTAIN SANCTION MW AND LBW AND SPECIAL REPAIRS WORKS AT MILITARY STATION SRI GANGANAGAR

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep, surface preparation as per required gradient and camber including well ramming and getting out in soft/loose soil complete all as specified and directed by Engineer - in - Charge

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and directed by Engineer - in - Charge

Excavation in trenches in n.exc. 1.5 m wide & n. exc. 1.5m in depth in soft/ loose soil for laying of cable complete all as specified and directed by Engineer - in - Charge

Returning filling in, including spreading levelling, watering and well ramming in layers not exc. 25 cms thick in soft/ loose soil complete all as specified and directed by Engineer - in - Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil complete all as specified and directed by Engineer - in - Charge.

M & L for sand filling (25 mm thick) under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer - in - Charge.

Supply & filling/ laying a layer of dry coarse sand 8 cm thick before laying ofcable and 15 cm thick after laying of cable complete all as specified and directed by Engineer - in - Charge. Note:- After punning drain 18 cm will be measured for payment.

Removing excavated material n. exc. 50 m & depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed by Engineer - in - Charge.

M&L for hard core of gauge exc 63 mm but n. exc 100 mm, deposited spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed by Engineer - in - Charge. complete all as specified and directed by Engineer - in - Charge.

M&L for PCC 1:3:6 Type C-2 (40mm graded stone aggregate) for foundations filling of post hole and struts complete all as specified and directed by Engineer - in - Charge.

M&L for PCC (1:4:8) type D-2, (40 mm graded stone aggregate) as in foundation filling in mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for PCC (1:3:6) type B-0, (40 mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directeds complete all as specified and directed by Engineer - in - Charge. complete all as specified and directed by Engineer - in - Charge

M&L for PCC 1: 2:4 Type B-1 (20 mm graded stone aggregate)as in block masonry with solid blocks, exc. 10 cm in width and setting in CM (1:4),complete all as specified and directed by Engineer - in - Charge.

M&L providing precast cement concrete 1:2:4, Type B1 using 20mm graded aggregate as in kerb stone with solid blocks exc 10cm width and set in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in chajjas, slabs complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engineer - in - Charge

M & L brick work with sub class 'B' bricks(old size) straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 but except bricks complete all as specified and directed by Engineer - in - Charge.

M & L brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M & L brick work with fly ash bricks, straight or curved on plan exc 6m mean raduis in half bricks, built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M&L for brick protection layer with one brick wide using sub class ‘B’ bricks laid flat across the cable complete all as specified and directed by the Engineer in charge.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engineer - in - Charge

M&L for formwork to to sides of pillars, posts, struts, piers, columns and stanchions for square, rectangular pr polygonal including for edges rough finished surfaces of concrete complete all as specified and directed by Engineer - in - Charge

S&F second class soft wood timber scantlings clean sawn 40 sqcm and over in section, in any position complete all as specified and directed by Engineer - in - Charge.

S&F second class soft wood timber scantlings clean sawn 40 sqcm and over in section, in any position except timber scantling complete all as specified and directed by Engineer - in - Charge.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer - in - Charge.

S&F 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by Engineer - in - Charge.

S & F 35mm thick,Second class hard wood factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) n. exc.1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) exc. 1.5 sqm and n. exc.4 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any description exc. 1 Sqm but n.exc 2 sqm each and after easing/resecuring refixing in the same opening / place complete all as specified and directed by Engineer - in - Charge.

Taking down steel window or ventilator of n.exc 1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed by Engineer - in - Charge

S&F 10 mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/ G.I./M.S. as per specification and drawing replaced with wooden ceiling and accessories complete all as specified and directed by Engineer - in - Charge

S&F Fiber Glass Reinforced plastic (FRP) Door Frames of required colour of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides, MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer - in - Charge

S&F 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required colour and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F Mild steel barrel tower bolts 125 mm, stove enamelled black, with bright bolt and fixed complete all as specified and directed by Engineer - in - Charge.

S&F aluminium anodised barrel tower bolts 150mm long extruded section complete all as specified and directed by Engineer - in - Charge.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer - in - Charge.

S&F butt hinges, heavy weight, cold rolled mild steel, and fixed of size 100mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S&F butt hinges, heavy weight, cold rolled stainless steel, and fixed of size 100mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S&F in repair 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed by Engineer-in-Charge.

S&F 125 mm Mild steel pressed handles, oval type, stove enamelled black complete all as specified & directed by Engineer-in-Charge.

S&F Extruded aluminium alloy handles, fabricated type, anodised 150 mm long complete all as specified and directed by Engineer - in - Charge

S&F in repairs mortice lock with four lever (vertical type) with brass body 100 mm long complete all as specified and directed by Engineer-in-charge.

S&F in repairs drapery harrison rails/curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge. Make:- Prayag cat part No- 323-Tor equivalent cat part as approved by GE

S&F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 150mm anodised, with hard drawn steel spring, fixed in floor plate complete all as specified and directed by Engineer - in - Charge..

S&F door closer hydraulically regulated, designation No. 2, universal type, suitabel for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed by Engineer-in-charge.

S&F in repairs door closer hydraulically regulated, designation No. 2, universal type, suitabel for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed by Engineer-in-charge.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to window / ventilator with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and dia of neck 12 mm complete all as specified and directed by Engineer - in - Charge.

M&L for TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia using TMT bars complete all as specified and directed by Engineer - in - Charge.

S&F 10 mm dia MS round bar for fixing of chain link fencing with post complete all as specifies and directedby Engineer - in - Charge.

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engineer - in - Charge.

M&L for mild steel work as in posts and struts of fencing including cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer - in - Charge.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engineer - in - Charge

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed by Engineer - in - Charge

Fixing only of chain link fencing including line wires, any mesh size and type to any type of satanderds, rails, straining bolts etc including binding wire complete all as specifed and directed by engineer-in-charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.complete all as specified and directed by Engineer - in - Charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded.complete all as specified and directed by Engineer - in - Charge.

M&L for pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer - in - Charge.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long Size of grid 605 x 605mm complete all as specified and directed by Engineer - in - Charge

M&L for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. with Powder Coating on aluminium minimum thickness of powder coating 50 micron as per the specification top and bottom horizontal members and vertical members adjacent to walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and directed by Engineer - in - Charge.

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed by Engineer - in - Charge

S&F powder coated aluminium windows and ventilator luver shutters, side hung type without sash bars, aluminium saction weighing 0.55 kg/M including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as aluminium peg stay 150mm long (1No), powder coated aluminium hinges type B-21 100 mm long (2No), suitable powder coated aluminium handle -(1No), and powder coated aluminium self closing tower bolt 75mm long (1No) complete all as specified and directed by Engineer - in - Charge.

S&F power coated aluminium snap grid frame work for false ceiling size 605x605 mm including hangers complete all as specified and directed by Engineer - in - Charge

Supply only chain link fencing galvanised mild steel hot dipped(IS -2721) of 4 mm dia of mesh size 100x100 mm complete all as specified and directed by Engineer - in - Charge. Note:- The weight of chain link fencing shall be ascertained by BOO as directed by GE and payment shall be paid accordingly BOO duly countersigned by GE shall be encloused with final bill.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated Mangalore tiles profile steel sheet 0.50mm thick of an colour (red) having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer - in - Charge

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain Mangalore tiles profile steel sheet 0.50mm thick of red colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

S&F 25 mm thick Prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations complete all as specified and directed by Engineer - in - Charge.

M&L for Providing and fixing Gypsum Board 12mm thick size (600x600) in false ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engineer - in - Charge

M & L for 75 mm thick cement concrete 1:3:6 type C –1 (20mm graded stone aggregate) as in plinth protection or similar works finished even and smooth with using extra cement etc complete all as specified and directed by Engineer - in - Charge.

M&L for 75mm thick cement concrete (1:4:8) type D-2, (40 mm graded stone aggregate) as in sub base, foundation filling and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for 25 mm thick cement concrete 1:2:4, Type B-0 (12.5mm graded aggregate) as in floor finished even and fair complete all as specified and directed by Engineer - in - Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.g complete all as specified and directed by Engineer - in - Charge.

M&L for precast coloured rubber moulded concrete machine pressed concrete interlocking paver blocks any shape and size conforming to IS 15658-2006 of 60 mm thickness, M 35 grade set, jointed and pointed in neat cement slurry in floors/paving/path etc wirh grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed by Engineer-in-charge.

M&L for glazed ceramic coloured tiles interior grade, of size 450x350x7mm thick as on vertical surfaces like dados or skirting laid over and including 15mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for glazed ceramic coloured tiles interior grade, of size 450x350x7mm thick as on vertical surfaces like dados or skirting laid over and including 10mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm in floor etc, laid over and including 15 mm thick screed bed in CM 1:4 and set and jointed in cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for virified ceramic tiles 7-8mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc 0.18 Sqm in skirting/dado etc,. laid over and including 10 mm thick rendering in CM 1:4, set and jointed in cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer-in-Charge

M&L for virified ceramic tiles 7-8mm thick (square / rectangular) area of each tile exc. 0.06 sqm but n. exc 0.11 Sqm in floors etc. laid over and including 15 mm thick screed bed in CM 1:4, set and jointed in cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer-in-Charge

M&L for virified ceramic tiles 10mm thick (square / rectangular) area of each tile n. exc 0.36 Sqm in floors etc. laid over and including 15 mm thick screed bed in CM 1:6, set and jointed in cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer-in-Charge

M&L for acid resistant tiles 15mm thick vitreous ceramic, unglazed on vertical surfaces in skirting/dado etc,. laid over and including 10 mm thick rendering in CM 1:4, set and jointed in cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer-in-Charge

M&L for acid resistant tiles 15mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L 20 mm thick Green marble machine cut as in skirting/dado and on shelves etc laid over 15 mm thick cement mortar 1:4 set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing etc complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick in CM 1:4 on brick work or concrete work surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 15 mm thick rendering in CM 1:6 on brick / concrete wall surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper, over a coat of chalk whiting with putty complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls with putty and applying two coats of cement based paint over a coat of white wash complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old decorated wall surfaces by brooming down or steel wire brushing,scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and then applying two coats of cement base paint with putty complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old decorated plastered or un-plastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered or un-plastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or concreate wall surfaces including racking out joints, hacking for key, scrubbing down with water etc. complete complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm the each pane complete all as specified and directed by Engineer - in - Charge.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm the each pane complete all as specified and directed by Engineer - in - Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new wood and wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of Pink primer complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old wood and wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer complete all as specified and directed by Engineer - in - Charge

M&L for preparation of old steel surfaces of any description over 10cm width or girth and applying one coats of synthetic enamel paint (ordinary tint) complete all as specified and directed by Engineer - in - Charge

S&F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised steel water tubing 20 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Fixing only Galvanised steel water tubing 15mm bore with new fitting including cutting chases to brick wall /ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge. Note;- Serviceable GI pipe obtained Srl item No 92 shall be re-used.

Fixing only Galvanised steel water tubing 20mm bore with new fitting and fixed to walls, ceiling or laid in floorscomplete all as specified and directed by Engineer-in-Charge. Note;- Serviceable GI pipe obtained Srl item No 95 shall be re-used.

Taking down 15 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

Taking down 20 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

Dismantling and taking down water tank of capacity exc. 250 Litre but n. exc. 500 litre capacity complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded white colour polyethylene water storage tank 500 litre capacity (Cylindrical vertical with closed top) hoisted and fixed in position with necessary fittings complete all as specified and directed by Engineer - in - Charge. (Note : PVC tanks shall be ISI marked, having two layres and white colour)

S&F in repairs 15mm bore angle stop cock / valve cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.Make: Prayag cat part no-8310 Parryware cat part no- T3507A1, Cera cat part no- F3002201

S&F in repairs 20mm bore angle stop cock / valve cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC connections 15mm size with PTMT nut of length 450mm complete all as specified and directed by Engineer-in-Charge.

S&F 100mm dia bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by Engineer - in - Charge

S&F 75mm dia bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by Engineer - in - Charge

S&F 100mm bore cast iron Bends (any radius),with duck's foot or heel rest diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore cast iron Bends (any radius),with duck's foot or heel rest diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, cromium plated shower rose of size 125mm with or without shivel joints including fixing to pipe or union complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 15mm bib tap cast copper alloy,fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule complete all as specified and directed by Engineer-in-Charge. Make: Prayag cat part no-8306 Parryware cat part no- T3504A1, Cera cat part no- HTF3001151

S&F grating doom 100 mm dia of PTMT fixed complete all as specified and directed by Engineer-in-Charge. Note:- Minimum weight 25gms

S&F in repair vitreous China wash down water closet pan (pedestal pattern), white complete, including white seat cover with hinging arrangement, (excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 10 litre capacity low level PVC valve less, syphonic action type flushing cistern, white, with inlet, ball valve, float and handle including bracket and provision of flush pipe of polythene of high density or PVC, 15mm dia and 450 mm long complete all as specified and directed by Engineer-in-Charge.

S&F in repair toilet paper holder, vitreous China,box type complete all as specified and directed by Engineer - in - Charge

S&F in repairs vitreous china wash hand basin white, flat back size 550x400mm including brackets, waste coupling 32mm dia of brass Chromium plated, 15mm dia pillar tap of cast copper alloy with capstan head screwed down, high pressure, with or without letter "Hot or Cold" with long screwed shank and fly nuts, 32mm dia, waste pipe low or high density polyethelene of pressure rating 6 Kg/Sqm and PVC connection with PTMT nuts of 15mm dia and 450mm long cutting for and pinning in end of brackets or erecting stand etc. complete all as specified and directed by Engineer - in - Charge.

S&F in repair vitreous china soap dish 160x160x90 mm fixed with screws complete all as specified and directed by Engineer - in - Charge

Demolition of brick work built in cement mortar or cement lime mortar complete all as specified and directed by Engineer - in - Charge

Demolition Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed by Engineer - in - Charge

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) of any description complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings 40 sqcm and over in section, in any position complete all as specified and directed by Engineer - in - Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer - in - Charge.

Dismantling galvalume sheet (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed by Engineer - in - Charge.

Dismantling Wall and ceiling boards (fibre,pulp, AC insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer - in - Charge.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by Engineer - in - Charge

Supplying, laying and testing 10 Sqmmx2 core XLPE insulated, heavy duty electric cable with aluminium conductor 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/ laid under roads/paths/ drain/ culverts or passing through pipes complete all as specified and directed by engineer in charge.

Supplying, laying and testing 25 Sqmmx4 core XLPE insulated, heavy duty electric cable with aluminium conductor 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/ laid under roads/paths/ drain/ culverts or passing through pipes complete all as specified and directed by engineer in charge.

Taking down copper/aluminium point wiring (light,fan,socket or power)complete including fixture and fittings such as switches& sockets and removing materials for taking credit complete all as specified and directed by Engineer-in-charge.

M&L for concealed conduit point wiring complete with cable 1.5 sqmm(Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC conduit pipe medium grade 20mm bore,pipe hooks,elbows,junction covers and junction boxes, after cutting in wall chasing for conduits and sinking's for sunken cast iron /pressed steel terminal boxes 60 mm deep of suitable length and 1.2 mm thickness for mounting switches, sockets, fan regulator with 3mm thick plastic laminated seat cover fixed with brass screws and cup washers, duly grouting and painted with red oxide metal primer and making good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth contuity conductor along with point wiring of 1.5 sqmm copper FRLS PVC insulated cable for point controlled by one way switch and connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

All as described in Srl item No -142 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No -142 here in before but for one switch socket combination 5/6 Amps on independent board complete all as specified and directed by Engineer - in - Charge.

M&L for concealed conduit point wiring complete for light /fan with cable 2.5 sqmm(Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC concealed conduit ( medium quality ISI marked) pipe medium grade 20mm bore,pipe hooks,elbows,junction covers and junction boxes, after cutting in wall chasing for conduits and sinking's for sunken cast iron /pressed steel terminal boxes of suitable length and thickness for mounting switches, sockets, fan regulator with 3mm thick plastic laminated seat cover fixed with brass screws and cup washers, duly grouting and painted with red oxide metal primer and making good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth contuity conductor along with point wiring of 2.5 sqmm copper FRLS PVC insulated cable for for one switch socket outlet 3 pin 15 Amps on independent board with complete all as specified and directed by Engineer - in - Charge.

S&F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S&F in repacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S&F switch piano flush type 5/6 Amp single pole one way complete all as specified and directed by Engineer - in - Charge

S&F Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S&F switch socket combination 5 pin, 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge

S&F Switch socket combination 2 in 1, 6 pin , 15/16 Amp flush universal type all as spd and directed by Engr in charge.

S&F in repairs MCCB TPN 63 Amps with braking capcity 16 kA, fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

S&F in repairs sheet metal enclosure for double door virtical DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounting VTPN 4 ways, 415 Volts, 250 amps bus bar, stove enamelled dust and vermin proof, IP:43 protection suitable for incorporation FP MCCB (v-Tech) N1 Frame upto 125A, isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer - in - Charge.

S&F in replacment MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S&F in repairs MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & Fin replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amps complete all as specified and directed by Engineer - in - Charge.

S&F in repairs sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 4 ways, 240 Volts, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F in repairs sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F in repairs sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 12 ways, 240 Volts, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F ceiling rose, surface bakelite 65x50 mm three terminals complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to the Galvanised iron earth lead 4 mm dia GI earth wire, by means of bolts, nuts check nuts and washers of galvanised iron and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (wieght not less than 4gs/Sqm) and frame of angle iron 25mm x 25mm x 6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm x 8 mm FI with fixing arrangements, funnel, wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 Mtrs all as per electrical Plate No.3 of SSR Part I and connecting to earth test point including taking our unserviceable earthing with all acessories all as specified or indicated including testing on completionall as specified and directed by Engineer - in - Charge.

S&F in replacement sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn and including steel dia "medium quantity" PVC conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surface and white wash or existing colour, necessary junction box and cover including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

S&F in repair stepped type,single socket fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all asspecified and directed by Engineer - in - Charge. Make- Crompton/Bajaj/Havell's/Orient

S&F extruded aluminium LED batten channel 20 watt having input voltage AC90-300V, 50Hz, 6500K, with white acrylic cover tube light fitting wall mounted complete with rod, driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS20WLED865SPCSS, Bajaj cat part No. BCLSBAL 20W CW, Crompton cat part No. CCS-100-20-65-HL2-DP-NWH

S&F in replacement extruded aluminium LED batten channel 20 watt having input voltage AC90-300V, 50Hz, 6500K, with white acrylic cover tube light fitting wall mounted complete with rod, driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS20WLED865SPCSS, Bajaj cat part No. BCLSBAL 20W CW, Crompton cat part No. CCS-100-20-65-HL2-DP-NWH

S&F LED lamp 9 W for angle holder complete all as specified and directed by Engineer - in - Charge.

S&F in replacement recess mounting 2x2 feet 36 watt LED luminaire with powder coated CRCA housing with LEDs, seamless front frame with high transmission acrylic cover and fixed electronic driver (surge protector ) complete all as specified and directed by Engineer - in - Charge . Make :-crompton cat part No. LCTLRNE-36-FO-CDL or equivalent make in Bajaj , havells

S&F in repairs water tight bulk head fitting, comprision of connector galvanised cast iron back plate, weather proof enamelled gallery, glass well and including 10 watt LED lamp complete all as specified and directed by Engineer-in-Charge. Make :-Havells cat part No. HEXAFT10WLED857SSYMBOPC, Bajaj cat part No. BIBWP 10W LED, Crompton cat part No. LBHP-10-CDL

S&F in replacement security light fitting LED TYPE 25 watt with all necessary accessories, Clear transparent acrylic cover, prewired suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. ENDURAPEARLSL25WLED757SASYTOPCMP, Bajaj cat part No. BRLEP 25 W, Crompton cat part No. LSTS-25-CDL-M

S&F in replacement compact decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1x10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS10WLED865SPCSS, Bajaj cat part No. BCLSB 10 WH, Crompton cat part No. LDL-10-CDL

S&F in replacement decorative wall light fixture made up of poly carbonate suitable for 10 watt LED lamp complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LHFOFWE1TZ1W012 or equivalent Bajaj, Crompton

Note : Notes : (i) Amount of credit for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

M/S KARNI CONSTRUCTION COMPANY

M/s Durga Constructions Company