CERTAIN REPAIRS TO SANITARY FITTINGS AND PLUMBING WORK INCLUDING CONNECTED WORKS IN MD ACCN UNDER AGE B/R II OF GE HISAR AT HISAR MIL STN

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level) complete, all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves, cooking platform and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete all as specified.

M&L for reinforcement TMT bars 8 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

M&L for 25mm thick PCC 1:2:4 type B0 using 20mm graded crushed stone aggregate as in sub base, finished even and fair all as specified and as directed.

M&L for non skid ceramic jointless tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic jointless tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic jointfree tiles (coloured) 300mm x 200mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic (dark & light shade) jointfree tiles (coloured) 450mm x 300mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for Granite (of any type) slab 18-20mm thick machine cut, as in floor, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for black marble (of any type) slab 18-20mm thick machine cut, as in floor, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble stone including grinding and polishing laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified & directed.

M&L for rendering 12mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L rendering 10mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement mixed with and including liquid water proofing compound @200 ML per 50 KG by weight of cement complete all as specified and directed.

Material and labour preparation of newly plastered cement surfaces of walls & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint of approved shade/tint complete all as specified and directed.

M&L for applying 2mm thick wall care putty on walls including filling cracks or holes complete all as specified and directed.

M&L for applying 2mm thick wall care putty on ceilings including filling cracks or holes complete all as specified and directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces complete all as specified & as directed.

Taking up or down 15mm bore steel / PVC /UPVC tubing and connection from any position concealed / exposed incl cleaning for refixing or removal to store.

Taking up or down 20mm bore steel / PVC /UPVC tubing and connection from any position concealed / exposed incl cleaning for refixing or removal to store.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Fixing only GI water tubing 15 mm bore, medium grade, with & including supply & fixing all new fittings (ISI marked) complete fixed to walls and ceilings or laid in floors all as specified & as directed. Notes :- (i) Old serviceable water tubing retrieved from serial item No. 27.00 here-in-before shall be used. (ii) Quoted rate shall be deemed to include cost of GI fittings (ISI marked). Old fittings shall not be used.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Fixing only GI water tubing 20 mm bore, medium grade, with & including supply & fixing all new fittings (ISI marked) complete fixed to walls and ceilings or laid in floors all as specified & as directed. Notes :- (i) Old serviceable water tubing retrieved from serial item No. 28.00 here-in-before shall be used. (ii) Quoted rate shall be deemed to include cost of GI fittings (ISI marked). Old fittings shall not be used.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall.

Cleaning and removing all scale and dirt, etc, from tanks 500 litres and not exc 1000 litres and from mouths of circulating pipes, etc. complete all as specified and directed.

Dismantling old unserviceable PVC water tank capacity 500 ltr and not exc 1000 ltrs & removal from site etc complete all as specified and directed.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S & F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S & F in repairs Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 15mm bore (minimum weight 142 gms) complete all as specified and as directed.

S & F in repairs Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S & F in repairs 20mm dia nipple suitable for PVC tanks (minimum weight 45 gms) complete all as specified and as directed.

S&F in repairs Bib taps,cast copper alloy with crutch or butterfly handle, chromium plated, fancy type , screwed for iron pipe or for brass ferrule, for 15 mm bore GI pipe complete.

S&F in repairs 15mm bore, fancy type brass CP wall mixer 3 in 1 system with 115mm bend pipe & areator complete all as specified and as directed. Make - Cat Part No MQT-519KN of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 15mm bore, fancy type brass CP wall mixer with telephonic shower arramgement with crutch (with Bush & Piston Diverter fitting) with areator complete all as specified and as directed. Make - Cat Part No MQT-517KN of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 15mm bore, fancy type brass CP hand shower pack (single flow 80mm round hand shower with 1.50m long spirochrome flex hose & wall bracket complete all as specified and as directed. Make - Cat Part No SAE-1929SH555 of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 15mm bore, fancy type brass CP central hole basin mixer with U shape round casted spout with 450mm long braided hoses complete all as specified and as directed. Make - Cat Part No TQT-516A of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 15mm bore, fancy type brass CP Sink mixer with swinging casted spout with areator complete all as specified and as directed. Make - Cat Part No MQT-521KN of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 15mm bore, fancy type brass CP Hand Shower (Health Faucet) (ABS Body) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook complete all as specified and as directed. Make - Cat Part No ALE-BLC-593 of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs CP flexible tube 8mm Dia, 1.2 Meter Long suitable for Hand shower / Health Faucet with wall hook complete all as specified and as directed.

S&F in repairs Jet Spray with 1 Meter PVC Tube (Stainless Steel) complete all as specified and as directed. Make - Cat Part No ALE-547 of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs fancy type brass CP Toilet paper holder complete all as specified and as directed. Make - Cat Part No AEC-1151N of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 2-Way Angle Valve with Wall Flange, chromium plated, fancy type , screwed for iron pipe or for brass ferrule, for 15 mm bore GI pipe complete. Make - Cat Part No DLX-526AFKN of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs Peg set of 06, steep chromium plated complete all as specified and as directed.

S&F in repairs PVC flexible waste pipe 32mm dia and 90cm long including adopter complete all as specified and as directed.

S&F in repairs PVC flexible waste pipe 40mm dia and 90cm long including adopter complete all as specified and as directed.

S&F in repairs brass CP 32mm dia waste coupling full threaded complete all as specified and as directed. Make - Cat Part No ALE-544NFT of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs brass CP 40mm dia waste coupling full threaded complete all as specified and as directed. Make - Cat Part No ALE-543FT of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 15mm bore stop valve, fancy type , chromium plated cast copper alloy screwed down, high pressure, with long shank and cup (concealed type) with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed.

S&F in repairs 15mm dia Angle Valve (Basin Inlet Connection) brass CP complete all as specified and as directed. Make - Cat Part No MQT-526KN of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes.& fly nuts, screwed for iron pipes.

S&F in repairs soap dish, brass CP fancy type complete. Make - Cat Part No BA-05 of Prayag or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints including shower arm 15mm size 195mm long bend of 45 degree with flange of CP fixing to steel pipe or union complete all as specified and directed.

S&F in repairs 15mm bore bib tap standard of PTMT any colour, high pressure, screwed for iron pipe and fixed (minimum weight 90 gms) complete all as specified and as directed.

S&F in repairs 15mm bore Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-110gms) complete all as specified and directed.

S&F in repairs 15mm bore Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms) complete all as specified and directed.

S&F in repairs 20mm bore Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 20mm-92gms) complete all as specified and directed.

S&F in repairs 15mm bore angle valve of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms) complete all as specified and directed.

S&F in repairs shower rose of PTMT any colour for fixing with 195mm long with bend of 45 degree with flange of PTMT (Minimum wt 80 gms) etc complete all as specified and directed.

S&F in repairs soap dish, PTMT, fixed on wall with screws complete. Make - Cat Part No 195 of Prayag or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs CP grating 100 mm dia (minimum weight 25 gram) complete all as specified and directed.

S&F in repairs grating dome 125mm dia with waste hole of PTMT (minimum weight 40 gram) complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets duly painted with two coats of synthetic enamel paint over a coat of red oxide primer embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe 90cm long, and 32mm bore PTMT waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs wall hung vitreous china wash hand basin with full pedastal, white, flat back of size 540mm x 395mm x 185mm with & including a pair of cast iron brackets duly painted with two coats of synthetic enamel paint over a coat of red oxide primer embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified. Make - Cat Part No CMS-WHT-103801 or CMS-WHT-103301 of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs pedastal for suitable for wash hand basin, white, complete all as specified. Make - Cat Part No CMS-WHT-103301 of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, with PTMT trap of suitable size 'P' or 'S' , including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

S&F in repairs vitreous china wash down water closet (Padestal pattern) White, with 'P' or 'S' trap including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

S&F in repairs PVC seat cover flat type for EWC confirming to IS-2548 complete all as specified and directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repairs complete set of flush kit of required shape & size suitable for 10 litre capacity PVC flushing cistern complete all as specified.

S&F in repairs PVC flush bend 32mm dia suitable for connecting PVC low level flsuhing cistern to any type WC complete all as specified.

S&F in repairs PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repairs PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repairs Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and plastic cleats (Minimum weight 190gms) complete all as specified..

S&F in repairs Towel Rail 600mm Long, Stainless Steel fixed with screws complete all as specified and directed. Make - Cat Part No AEC-1111N of ESSCO Jaquar or equivalent of makes mentioned in Appx 'C' here-in-after.

S&F in repair kitchen sink (overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm or nearest higher size) ) made from high grade AISI-304 (18/8) stainless steel of 1mm thickness including 32mm bore brass CP waste coupling, plug, washer, 32mm bore and 600mm long PVC waste pipe including fixing cantilever brackets made of MS angle iron 30x30x3mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning of ends of brackets to errecting stand into wall and making good distrubed portion in CM (1:2) on in PCC (1:2:4) using 20mm graded stone aggregate and connecting union to pipe complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc. (measured overall as fixed along the centre line over fitting and accessories) complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified.

S&F 110mm bore PVC (SWR) bend with access door all as specified & as directed.

S&F 75mm bore PVC (SWR) bend with access door all as specified & as directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal provided with access door complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal provided with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified.

M&L for treatment of sunken floor slab compraises of the following specifications and all as specified :- (i) M&L for cleaning the sunken/lowered portion of RCC slab surface (including vertical surfaces upto finished floor level) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely and providing 40mm thick avgerage PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for providing spout 50mm bore GI pipe medium grade of length 0.50m and fixed all as specified. (ii) M&L for providing rendering of uneven surfaces of vertical sunken with 6mm thick CM 1:4 mixed with integral water proofing compound @ 3% by wt of cement consumed. (iii) M&L for applying two coats of polymer modified cementious water proof coating as per manufacturers instruction to bottom and vertical sides up to finished floor level and 100mm aove FFL , the thickness of two layer shall be 1mm and when the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. (iv) M&L for providing plaster to the bottom and sides up to FFL with minimum 20mm thick CM 1:4 mixed with integral water proofing compound 3% by wt of cement consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. (v) The sunken floor shall be filled with lean concrete 1:7:12

Note :- (i) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty. (iii) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (iii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint and cost is deemed shall be included in quoted rates. (iv) Cost of WPC shall deemed to be included in quoted rates. (v) Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage to the entire satisfaction of GE. Test shall be done in presence of reps of Engineer-in-charge and record for each sunken slab shall be maintained. (vi) The treatment shall be carried out in presence of Engineer-in-charge and tested. Cost of testing is inclued in the rates quoted above. (vii) For Payment purpose, the Plan area of Sunken floor shall be taken into account.

S&F in repairs single/multi PVC (SWR) floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement all as specified.

Shiva Constructin Co.

M/s Rao Constructions, 1173 Urban Estate-II, Hisar

m/s Rajesh Kumar