CIVIL AND STRUCTURAL WORK

Amount

EARTHWORK Note : 1. The mode of measurement will be box cutting keeping the bottom dimension of PCC. 2. Hard rock & Hard rock are mixed, the measurement will be as per section II Chapetr 4 Clause 1.0. 3. The contractor may be asked to excavate and transport the earth directly for mass backfilling in other areas. In such cases, no extra payment for backfilling shall be made. 4. Contractor has to take prior approval from Engineer/ Consultant for excavation using hydraulic excavator/rock breaker attachment/any other mechanical means identifying the strata and approximate quantity of work involved. 5. Adequate precautions for carrying out deep excavation work have to be taken by the Contractor.

A-1 (a) Earthwork in excavation in all types of soil including sand & silty sand, moorum (hard, compacted or soft), broken rock, boulders, quartz etc and fill materials or any other debris etc. at depths as specified below in foundations of structures and equipment, pipe trenches, tunnels, sewerlines, drains, basement, cellars, pits etc to required levels and grades and dressing complete in all respect as per the specifications and directions of the Engineer/ Consultant in both dry and wet conditions including necessary pumping/ bailing out of water, slush removal etc and transporting the excavated materials to spoil dumps/fill areas/excavated pits within a lead of 1 km at all heights and descents including dozing, levelling at the site of filling all as directed by the Engineer/ Consultant, all tools, plant and labour complete in all respect (The mode of measurement will be box cutting keeping the bottom dimension of PCC considering additional working space, benching and side slopes, etc.) Note for item A-1(a) This item will be operated upon that category of strata which can be excavated by Mechanical means with reasonable application as approved by the Engineer/ Consultant, with all tools and labour complete in all respect: i) upto 3 m depth below finished ground level

A-1 (a) Earthwork in excavation in all types of soil including sand & silty sand, moorum (hard, compacted or soft), broken rock, boulders, quartz etc and fill materials or any other debris etc. at depths as specified below in foundations of structures and equipment, pipe trenches, tunnels, sewerlines, drains, basement, cellars, pits etc to required levels and grades and dressing complete in all respect as per the specifications and directions of the Engineer/ Consultant in both dry and wet conditions including necessary pumping/ bailing out of water, slush removal etc and transporting the excavated materials to spoil dumps/fill areas/excavated pits within a lead of 1 km at all heights and descents including dozing, levelling at the site of filling all as directed by the Engineer/ Consultant, all tools, plant and labour complete in all respect (The Contractor shall quote the rate considering additional working space, benching and side slopes, etc.) ii) exceeding 3 m depth upto 6 m depth below finished ground level

A-1 (b) Same as item A-1(a), but for excavation done manually on approval/written instruction given by the Engineer/consultant, with all tools, plant and labour complete in all respect. i) upto 3 m depth below finished ground level

A-1(c) Excavation in hard, compacted or soft rock, boulders, etc done with the help of excavator provided with hydraulically operated rock breaker attachment or equivalent or for excavation done by any other mechanical means as approved by the Engineer/ Consultant, all tools, plant and labour complete in all respect: i) upto 3 m depth below finished ground level

A-1(c) Excavation in hard, compacted or soft rock, boulders, etc done with the help of excavator provided with hydraulically operated rock breaker attachment or equivalent or for excavation done by any other mechanical means as approved by the Engineer/ Consultant, all tools, plant and labour complete in all respect: ii) exceeding 3 m depth upto 6 m depth below finished ground level

A-1(d) Excavation in hard, compacted or soft rock, boulders, etc done manually with the help of pneumatically operated chiesel/breaker viz. Paving breaker, jack hammer or any other approved means as per the direction of Engineer/Consultant, all tools, plant and labour complete in all respect: i) upto 3 m depth below finished ground level

A-2 Backfilling in all positions and heights and descents in foundations, pits, pipe trenches, tunnels, sewer lines, around foundations and structures, in plinth etc with approved excavated material obtained within a lead of 1 km including reclaiming from spoil heaps at all heights, or reclaiming from dump at all depths, transporting, depositing and dressing complete in all respect as per drawings, specifications and directions of the Engineer/Consultant, all tools, plant and labour complete in all respect: a) mass backfilling including dozing, leveling and dressing complete in all respect as directed by the Engineer/Consultant

A-2 Backfilling in all positions and heights and descents in foundations, pits, pipe trenches, tunnels, sewer lines, around foundations and structures, in plinth etc with approved excavated material obtained within a lead of 1 km including reclaiming from spoil heaps at all heights, or reclaiming from dump at all depths, transporting, depositing and dressing complete in all respect as per drawings, specifications and directions of the Engineer/Consultant, all tools, plant and labour complete in all respect: b) backfilling in layers not exceeding 250 mm thickness including dozing, leveling, dressing and compacting complete in all respects as directed by the Engineer/Consultant.

A-2 Backfilling in all positions and heights and descents in foundations, pits, pipe trenches, tunnels, sewer lines, around foundations and structures, in plinth etc with approved excavated material obtained within a lead of 1 km including reclaiming from spoil heaps at all heights, or reclaiming from dump at all depths, transporting, depositing and dressing complete in all respect as per drawings, specifications and directions of the Engineer/Consultant, all tools, plant and labour complete in all respect: c) plinth filling in layers of 150 mm thickness where special compaction is required including watering and consolidating by mechanical means as per specification and directions of the Engineer/Consultant.

A-3 Supplying, filling, watering and compacting coarse sand in foundations, pipe trenches, pits, sewerlines, drainage lines, plinth, underneath flooring and in soaking pits etc all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

A-4 Providing timber shoring and strutting at all depths below ground level in trenches, foundations, as specified a) close boarded shoring

A-4 Providing timber shoring and strutting at all depths below ground level in trenches, foundations, as specified b) open boarded shoring

A-5 Supplying and providing of sand bag shoring at all depths in foundations and trenches as directed by the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

A-6 Micro levelling, dressing, watering and compacting of ground - surrounding the buildings and paved areas, wherever necessary in all kinds of soils to the required finished ground level and profile including all leads and lifts and disposal of surplus earth or obtaining earth required for filling within initial lead of 1000 m, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

A-7 Stripping the existing ground for a depth of 150 mm in all kinds of soil/slag and fill materials except only the hard rock and disposing the excavated materials at a distance upto 3 km within plant boundary including dressing to level as directed by the Engineer/Consultant with all lifts complete in all respect.

A-8 Extra over item A1(a), A1(b), A-7, A-8 for disposal of excavated material for a lead beyond initial lead of 1000 m but within 2000m

PLAIN & REINFORCED CEMENT CONCRETE 1. Suffix A, B, C and D to the grade of concrete indicate the use of size of the graded coarse stone aggregates in concrete as follows: A-75 mm and down graded stone aggregate B-40 mm and down graded stone aggregate C-20 mm and down graded stone aggregate D-10 mm and down graded stone aggregate 2. In case of supply of concrete, civil contractor shall use batching plants, transit mixers and concrete pumps with boom placer equipment (if required) etc for all major concreting works and the rate shall include the provision for the same. 3. All reinforced concrete shall be done using super-plasticiser as per manufacturer's instruction and as directed by Engineer/ Consultant. 4. All concreting work shall be done with 53 Grade OPC cement as per latest IS codes shall be used. OPC shall be used in all strength related concrete elements like foundations, walls, columns, beams and slabs, PCC, DPC, Roads and precast structure for cover slabs of drains.

B-1 Supplying, laying and compacting plain cement concrete of nominal mix M7.5 by volume as defined by IS:456 in all mudmats/levelling courses including filling of loose pockets etc. under foundations, pipelines, tunnels, floors etc at all depths below finished ground level as per drawings, specifications and directions of the Engineer/ Consultant, including curing but excluding the cost of shuttering, all materials, tools, plant and labour complete in all respect: a) with 40 mm down graded coarse stone aggregates

B-1 Supplying, laying and compacting plain cement concrete of nominal mix M7.5 by volume as defined by IS:456 in all mudmats/levelling courses including filling of loose pockets etc. under foundations, pipelines, tunnels, floors etc at all depths below finished ground level as per drawings, specifications and directions of the Engineer/ Consultant, including curing but excluding the cost of shuttering, all materials, tools, plant and labour complete in all respect: b) with 20 mm down graded coarse stone aggregates

B-2 Supplying, laying and compacting plain cement concrete of following grades as defined by IS:456, in all foundations, bed blocks, manholes, chambers, scale flumes, tunnels, trenches, floors, roofs, pavements, screedings, encasing etc at and at all heights and depths above and below finished ground level to required levels, slopes etc including curing but excluding the cost of shuttering, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) for M10B grade concrete

B-2 Supplying, laying and compacting plain cement concrete of following grades as defined by IS:456, in all foundations, bed blocks, manholes, chambers, scale flumes, tunnels, trenches, floors, roofs, pavements, screedings, encasing etc at and at all heights and depths above and below finished ground level to required levels, slopes etc including curing but excluding the cost of shuttering, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) for M10C grade concrete

B-2 Supplying, laying and compacting plain cement concrete of following grades as defined by IS:456, in all foundations, bed blocks, manholes, chambers, scale flumes, tunnels, trenches, floors, roofs, pavements, screedings, encasing etc at and at all heights and depths above and below finished ground level to required levels, slopes etc including curing but excluding the cost of shuttering, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: c) for M15 C grade concrete

B-2 Supplying, laying and compacting plain cement concrete of following grades as defined by IS:456, in all foundations, bed blocks, manholes, chambers, scale flumes, tunnels, trenches, floors, roofs, pavements, screedings, encasing etc at and at all heights and depths above and below finished ground level to required levels, slopes etc including curing but excluding the cost of shuttering, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: d) for M15D grade concrete

B-3 Supplying, laying and compacting reinforced cement concrete of following grades as defined by IS:456, in all foundations and super structures, in walls, beams/corbels, etc including curing but excluding cost of shuttering and steel reinforcement, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: i) for M25C grade concrete a) At and at all depths below finished ground level

B-3 Supplying, laying and compacting reinforced cement concrete of following grades as defined by IS:456, in all foundations and super structures, in walls, beams/corbels, etc including curing but excluding cost of shuttering and steel reinforcement, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: i) for M25C grade concrete b) Upto the initial height of 3.5 m above finished ground level

B-3 Supplying, laying and compacting reinforced cement concrete of following grades as defined by IS:456, in all foundations and super structures, in walls, beams/corbels, etc including curing but excluding cost of shuttering and steel reinforcement, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: i) for M25C grade concrete c) Extra for each lift of 3.5 m over and above the initial height of 3.5m

B-4 Supplying and placing damp-proof course 40 mm thick with concrete of M20 grade as defined by IS:456 with 6 mm and down graded stone aggregates including applying of two coats of hot bitumen as per IS:3384 when the concrete has partially set @1.7 kg per sq m and spreading of sand as per IS:383 over the bitumen, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

B-5 Supplying, manufacturing, erecting and fixing in position at and at all heights and depths above and below finished ground level different types of precast R.C. units of concrete grade M-25 as defined by IS:456 with 20 mm and down graded stone aggregates including shuttering and curing but excluding steel reinforcement, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect a) for units weighing upto 0.5 ton

B-5 Supplying, manufacturing, erecting and fixing in position at and at all heights and depths above and below finished ground level different types of precast R.C. units of concrete grade M-25 as defined by IS:456 with 20 mm and down graded stone aggregates including shuttering and curing but excluding steel reinforcement, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect b) for units weighing above 0.5 ton and upto 1.5 ton

B-6 Supplying, laying and compacting reinforced cement concrete of M-30 grade as defined by IS:456, in all equipment foundations and super structures, in walls, slab, columns, beams, floor/roof slabs, footings, trenches, etc including curing but excluding cost of shuttering and steel reinforcement, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect

STEEL REINFORCEMENT Note: 1. The cutting and bending of steel reinforocement shall be done by reinforcement cutting & bending machine.

C-1 Supplying, loading, transporting, unloading, straightening, decoiling, cutting, bending, cranking, bending, tack welding as necessary, placing and fixing in position steel reinforcement including angles/pins provided for the approved welded joints, at all levels above and below finished ground level for reinforced cement concrete and precast reinforced cement concrete works including supplying approved 20 SWG annealed black binding wire, cover blocks etc all as per drawings, specifications and directions of the Engineer/ Consultant all materials, tools, plant and labour complete in all respect: a) with M.S. rounds of all diameters

C-1 Supplying, loading, transporting, unloading, straightening, decoiling, cutting, bending, cranking, bending, tack welding as necessary, placing and fixing in position steel reinforcement including angles/pins provided for the approved welded joints, at all levels above and below finished ground level for reinforced cement concrete and precast reinforced cement concrete works including supplying approved 20 SWG annealed black binding wire, cover blocks etc all as per drawings, specifications and directions of the Engineer/ Consultant all materials, tools, plant and labour complete in all respect: b) with high strength deformed bars of grade Fe500D of all diameters

INSERTS, EMBEDMENTS AND OTHER STEELWORKS

D-1 Supplying structural steel materials, loading, transporting, unloading, fabricating, erecting and fixing in position at and at all heights and depths above and below finished ground level, M.S. plates for anchor box, permanent steel shuttering (with or without anchor pin) for anchor bolt pockets (straight or tapered) for embedding permanently in concrete or masonry work, true to line, level and plumb including all connected works and adjustments in shuttering and reinforcement, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect.

D-2 Supplying, fabricating, erecting and fixing in position at and at all heights and depths above and below finished ground level M.S. foundation/anchor bolts, plates for anchor box with/without sleeves for T-headed bolts, permanent steel shuttering (with or without anchor pin) for anchor bolt pockets (straight or tapered) with all nuts and washers for embedding in permanent concrete or masonry work, true to line, level and plumb including all connected works and adjustments in shuttering and reinforcement, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

D-3 Supply structural steel material, loading, transporting, unloading, fabricating, erecting and fixing in position at and at all heights and depths above and below finished ground level, M.S. inserts, curb angles, channels, joists and other rolled sections including applying two coats of red oxide primer on exposed surface.

D-4 Supply structural steel material, loading, transporting, unloading, fabricating, erecting and fixing in position at and at all heights and depths above and below finished ground level M.S. inserts, curb angles, channels, joists and other rolled sections. a) M.S. plates/flat inserts, angles, channels etc. with lugs, rungs, fabricated ducts etc.

D-4 Supply structural steel material, loading, transporting, unloading, fabricating, erecting and fixing in position at and at all heights and depths above and below finished ground level M.S. inserts, curb angles, channels, joists and other rolled sections. b) G.S. Pipe/Pipe sleeves/conduits of various diameter (IS:1239) with or without puddle flange

D-4 Supply structural steel material, loading, transporting, unloading, fabricating, erecting and fixing in position at and at all heights and depths above and below finished ground level M.S. inserts, curb angles, channels, joists and other rolled sections. c) M.S. tube for tubular hand railing of various diameter (IS:1161), M.S. Pipe/Pipe sleeved/conduits with or without puddle flange

D-5 Supplying structural steel material, loading, transporting, unloading, fabricating, erecting and fixing in position at all heights and depths above and below finished ground level structural steelwork in M.S. ladders, stairs, platforms, brackets, runners, stringers, posts, stiffeners, monorails, structural beams, hand railings, frames in openings etc including supplying and applying painting with two coats of synthetic enamel paint of make, colour and shade as approved by the Engineer/Consultant over one coat of primer conforming to IS:2074 all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

SHUTTERING

E-1 Providing and fixing shuttering (formwork) in position with necessary centerings, bracings, proppings etc and striking, removing and clearing the same after the specified periods for all types of shuttering for all plain and reinforced cement concrete works including all chamfers, splays, fillets, keys, wedges, props, nails, bracings, brackets, cutting holes for passing embedments etc and applying waste oil on shuttering surfaces in contact with concrete all as per drawings, specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect: a) Straight shuttering i) at and at all depths below finished ground level

E-1 Providing and fixing shuttering (formwork) in position with necessary centerings, bracings, proppings etc and striking, removing and clearing the same after the specified periods for all types of shuttering for all plain and reinforced cement concrete works including all chamfers, splays, fillets, keys, wedges, props, nails, bracings, brackets, cutting holes for passing embedments etc and applying waste oil on shuttering surfaces in contact with concrete all as per drawings, specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect: a) Straight shuttering ii) Upto the initial height of 3.5 m above finished ground level

E-1 Providing and fixing shuttering (formwork) in position with necessary centerings, bracings, proppings etc and striking, removing and clearing the same after the specified periods for all types of shuttering for all plain and reinforced cement concrete works including all chamfers, splays, fillets, keys, wedges, props, nails, bracings, brackets, cutting holes for passing embedments etc and applying waste oil on shuttering surfaces in contact with concrete all as per drawings, specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect: a) Straight shuttering iii) Extra for each lift of 3.5 m over and above the initial height of 3.5m

E-1 Providing and fixing shuttering (formwork) in position with necessary centerings, bracings, proppings etc and striking, removing and clearing the same after the specified periods for all types of shuttering for all plain and reinforced cement concrete works including all chamfers, splays, fillets, keys, wedges, props, nails, bracings, brackets, cutting holes for passing embedments etc and applying waste oil on shuttering surfaces in contact with concrete all as per drawings, specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect: b) Curved shuttering i) Below GL

E-1 Providing and fixing shuttering (formwork) in position with necessary centerings, bracings, proppings etc and striking, removing and clearing the same after the specified periods for all types of shuttering for all plain and reinforced cement concrete works including all chamfers, splays, fillets, keys, wedges, props, nails, bracings, brackets, cutting holes for passing embedments etc and applying waste oil on shuttering surfaces in contact with concrete all as per drawings, specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect: b) Curved shuttering ii) Above GL

E-2 Providing and fixing in position shuttering for core holes and pockets for building column and equipment foundation bolts etc including all temporary formwork, applying one coat of waste oil on shuttering surfaces in contact with concrete and striking, removing and clearing shuttering after the specified period, cleaning and protecting the core holes and pockets, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect

MASONRY WORK

F-1 Supplying, constructing one or more brick thick Fly ash brickwork using bricks of Class10 with compressive strength not less than 100 kgf/sq cm as defined in IS:12894 in cement sand mortar (1:6) in foundations, super structure, manholes, ducts, drains etc including fair cutting, waste, bonding, plumbing, lining, levelling, flushing, raking joints, scaffolding and curing, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect a) at all depths below finished ground level

F-1 Supplying, constructing one or more brick thick Fly ash brickwork using bricks of Class10 with compressive strength not less than 100 kgf/sq cm as defined in IS:12894 in cement sand mortar (1:6) in foundations, super structure, manholes, ducts, drains etc including fair cutting, waste, bonding, plumbing, lining, levelling, flushing, raking joints, scaffolding and curing, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect b) at all heights above finished ground level

F-2 Supplying and constructing half-brick thick Fly ash brickwork, using bricks of Class10 with compressive strength not less than 100 kgf/sq cm as defined in IS:12894 in cement sand mortar (1:4) with continuous HB wire netting reinforcement at every fourth course at and at all heights and depths above and below finished ground level for partition walls and including fair cutting, waste, bonding, plumbing, lining, levelling, raking joints, scaffolding and curing, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect

F-3 Supplying and constructing 75 mm thick Fly ash brickwork in partition walls, parapets, fins etc at and at all heights and depths above and below finished ground level using bricks of Class10 with compressive strength not less than 100 kgf/sq cm as defined in IS:12894 in (1:4) cement sand mortar with continuous HB wire netting reinforce- ment at every third course, including fair cutting, waste, bonding, plumbing, lining, levelling, raking joints, scaffolding and curing as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

F-4 Supplying & constructing random uncoursed rubble masonry in cement sand mortar (1:6) in foundations, super structure etc with flush pointing as per specifications and as directed by the Engineer/Consultant at all depths and heights below and above finished ground level including wastage, scaffolding and curing, fair cutting, lining, levelling etc, all materials, tools, plants and labour complete in all respect.

F-5 Supplying & constructing coursed rubble masonry in cement sand mortar (1:6) in super structures including sunk pointing of finished size 15 mm wide and 10 mm deep or as directed by the Engineer/Consultant at all heights & depths above and below finished ground level, including wastage, scaffolding and curing, fair cutting, plumbing, lining, levelling etc all materials, tools, plants and labour complete in all respect.

PLASTER & FINISHING ITEMS

G-1 Supplying and laying plaster with (1:4) thick cement sand mortar with Fly Ash collected from Client site conforming to IS:3812 used as cement replacement material to the extent of maximum 10% at and at all heights and depths above or below finished ground level to ceilings, beams, staircases lintel soffits, chajjas, projections, narrow bands and widths etc including chipping of concrete surfaces, raking joints, scaffolding, cleaning and curing all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 6 mm thick

G-2 Supplying and laying plaster with (1:4) cement sand mortar with Fly Ash collected from Client site conforming to IS:3812 used as cement replacement material to the extent of maximum 10% at and at all heights and depths above and below finished ground level to faces of walls, pillars, columns, posts, lintel sides, drains, jambs, column projections, narrow bands and widths etc including chipping and hacking of concrete surfaces, raking joints, scaffolding, cleaning and curing, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 15 mm thick (in one operation)

G-2 Supplying and laying plaster with (1:4) cement sand mortar with Fly Ash collected from Client site conforming to IS:3812 used as cement replacement material to the extent of maximum 10% at and at all heights and depths above and below finished ground level to faces of walls, pillars, columns, posts, lintel sides, drains, jambs, column projections, narrow bands and widths etc including chipping and hacking of concrete surfaces, raking joints, scaffolding, cleaning and curing, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) 20 mm thick (in two operations)

G-3 Making vertical and horizontal grooves in cement plaster at and at all heights above finished ground level, finished neatly in line and level with sharp and square edges including scaffolding, curing etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 10 mm X 10 mm

G-3 Making vertical and horizontal grooves in cement plaster at and at all heights above finished ground level, finished neatly in line and level with sharp and square edges including scaffolding, curing etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) 25 mm X 10 mm

G-4 Supplying and laying following thickness of plaster with (1:3) cement sand mortar at and at all heights and depths above and below finished ground level including supplying and mixing approved waterproofing agent as per manufacturer's specification (Conplast X421 IC of Fosroc/Plastocrete Super/Cico No.1 of Cico or other approved equivalent) thickness of plaster applied in three layers (25 mm) and then finished with a coat of neat cement finish including chipping and hacking of concrete surfaces, raking joints, scaffolding, cleaning and curing, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect. Note: Dosage of admixtures shall be in line with manufacturer's specification and as approved by the Engineer/Consultant. a) 25 mm thick (for wall and base slab)

G-4 Supplying and laying following thickness of plaster with (1:3) cement sand mortar at and at all heights and depths above and below finished ground level including supplying and mixing approved waterproofing agent as per manufacturer's specification (Conplast X421 IC of Fosroc/Plastocrete Super/Cico No.1 of Cico or other approved equivalent) thickness of plaster applied in three layers (25 mm) and then finished with a coat of neat cement finish including chipping and hacking of concrete surfaces, raking joints, scaffolding, cleaning and curing, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect. Note: Dosage of admixtures shall be in line with manufacturer's specification and as approved by the Engineer/Consultant. b) 10 mm thick (for ceiling)

G-5 Supplying drip course 30 mm wide and 15 mm deep at chajjas, sills and other outside projections at all heights above finished ground level cement sand mortar (1:4), all materials, tools, plant and labour complete in all respect.

G-6 Supplying and applying two coats of interior grade acrylic emulsion paint of approved make and shades over a coat of approved primer to exposed surfaces of wall, ceiling, timber partitions, false ceiling etc at and at all heights above finished ground level including scaffolding, all as per specifications and directions of the Engineer, all materials, tools, plant and labour complete in all respect.

G-7 Supplying and applying two coats of exterior grade acrylic emulsion paint with silicone base of approved make and shades to exposed surface of wall, chajja, parapet etc including thorough cleaning of all loose, dirt, fungi, algae and fill up minor cracks of surface with cement sand mortar (1:3) at all heights above finished ground level including scaffolding, all as per specifications and directions of the Engineer, all materials, tools, plant and labour complete in all respect.

G-8 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified at all heights and depths above and below finished ground level including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect (measurement will be according to IS:1200): a) Steel doors

G-8 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified at all heights and depths above and below finished ground level including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect (measurement will be according to IS:1200): b) Steel windows & ventilators

G-8 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified at all heights and depths above and below finished ground level including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect (measurement will be according to IS:1200): c) Rolling shutters

G-8 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified at all heights and depths above and below finished ground level including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect (measurement will be according to IS:1200): d) Masonry/plastered surfaces

G-8 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified at all heights and depths above and below finished ground level including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect (measurement will be according to IS:1200): e) Steel inserts

G-8 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified at all heights and depths above and below finished ground level including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect (measurement will be according to IS:1200): f) Wooden doors & windows

G-9 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified to all exposed soil, waste and water supply pipe lines including all fittings such as bends, junctions, elbows, tees, sockets, clamps, bobbins etc including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect: a) For sizes between 15 mm dia and 25 mm dia

G-9 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified to all exposed soil, waste and water supply pipe lines including all fittings such as bends, junctions, elbows, tees, sockets, clamps, bobbins etc including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect: b) For sizes above 25 mm dia upto 75 mm dia

G-9 Supplying and applying two coats of approved synthetic enamel paint over one coat of approved primer confirming to IS:2074 as specified to all exposed soil, waste and water supply pipe lines including all fittings such as bends, junctions, elbows, tees, sockets, clamps, bobbins etc including rubbing, cleaning, putty filling etc and scaffolding, all materials, tools, plant & labour complete in all respect: c) For sizes above 75 mm dia upto 150 mm dia

G-10 Supplying and applying Cement based putty on cement plastered surfaces at and at all heights and depths above finished ground level including scaffolding, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

G-11 Providing neat cement finish on green plastered surfaces of drains, walls, pits, manholes, sewers etc at and at all heights and depths above and below finished ground level, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect

SOLING AND HARD CORE

H-1 Providing and laying single layer flat brick soling with bricks of compressive strength not less than 50 kgf/sq cm as defined in IS:12894 over a layer of sand bed of thickness 25 mm including dry sand filling of joints and brooming as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

H-2 Supplying, laying and packing stone boulder soling of finished thickness varying from 150 mm to 250 mm under floors/plinth/ foundations etc hand and hammer packed with spalls and stone chips and blinding with crushed stones including watering, ramming, compacting and rolling with a 8-10 ton power roller or by any other approved mechanical means, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

H-3 Providing and filling moorum of approved quality in layers, each layer not exceeding 100 mm thick, including consolidating each layer by watering and ramming at any location all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

H-4 Providing, filling and spreading 40 mm down graded gravel over finished ground level at any location at any depth all as per specification and direction of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect.

H-5 Providing 150 mm to 250 mm thick pitching with trap stone boulders to proper slope including thoroughly packing the joints with trap ballast and grouting with cement sand mortar (1:6) and finishing the joints flush as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

FLOORING

I-1 Supplying and laying 40 mm thick floor finish with 25 mm thick terrazzo tiles on 15 mm thick cement sand bedding mortar including curing, rubbing, machine polishing in 3 operations all as per specifications and directions of the Engineer/Consultant.

I-2 Supplying and laying 30 mm thick skirting / dado with 20 mm thick terrazzo tiles on 10 mm thick cement sand bedding mortar including curing, rubbing, machine polishing in 3 operations all as per specifications and directions of the Engineer/Consultant.

I-3 Supplying and laying 40 mm thick grey cement concrete (granolithic) floor finish in panels in floors, treads etc incl. supplying and providing approved pigments of specified colour, tamped, trowelled and finished smooth with a floating coat of neat cement including providing glass/aluminium strip dividers in joints for the full depth of the floor finish to form suitable panels and curing, as per the specifications and directions of the Engineer/Consultant. Concrete mix ratio of 1:1:2 (with 10 mm downgraded aggregate.

I-4 Supplying and laying 20 mm thick grey cement concrete finish as specified in skirting/dado, riser etc with 5mm thick cement sand mortar mixed with approved pigment of specified colour over 15 mm thick M-20 plain cement concrete including finishing curing, all as per specification and directions of the Engineer/Consultant.

I-5 Supplying and laying 15 mm thick heavy duty floor hardener topping course with "Ironite" @ 2.75 kg per sq m or approved equivalent including the bedding layer of 25 mm thick screed concrete M25D, topping course laid whilst the screed concrete is still green, all according to the manufacturer's specification including trowel finishing and curing, all as per specifications and directions of the Engineer, all materials, tools, plant and labour complete.

I-6 Supplying and laying overall 40 mm thick PVC tile floor finish of approved quality, size and shade with a layer of 25mm thick PCC, (M20D) two coats of bitumen paint on PCC surface and 13 mm thick cement sand bedding mortar over it, including fixing PVC tiles with rubber based adhesive conforming to manufacturer's specification as per specification and direction of the Engineer/Consultant: a) 2 mm thick homogeneous PVC tiles

I-7 Supplying and fixing 2 mm thick homogeneous PVC skirting / dado over plastered surface, levelled and smoothened with neat cement slurry and fixing with rubber based adhesive conforming to manufacturer's specification as per specification and direction of the Engineer/Consultant.

I-8 Supplying and laying 40 mm thick acid/alkali resistant flooring with 25 mm thick acid/ alkali resistant ceramic tiles of approved make conforming to IS:4457 over a 15mm thick bedding mortar and joints filled with resin mortar conforming to IS 4832 (Part-II), all as per attached manufacturer's specification and direction of the Engineer/ Consultant.

I-9 Supplying and laying 25 mm thick acid/alkali resistant skirting and dado with 12 mm thick acid/alkali resistant ceramic tiles conforming to IS:4457 with a 13 mm thick mortar bedding and joints filled with resin mortar conforming to IS:4832 (Part-II) all as per manufacturer's specifications and directions of the Engineer/Consultant.

I-10 Supplying & fixing overall 40mm thick Double charged vitrified tiles with anti skid & anti scratch of 1st quality of approved size, colour & make in floors including providing maximum 32mm thick cement sand bedding mortar, filling of joints with white cement paste mixed with matching pigments and cleaning with saw dust and dilute sulphuric acid, curing etc. all as per specifications and direction of the Engineer/Consultant: a) minimum 8 / 10 mm thick

I-11 Supplying and fixing overall 20mm thick Double charged vitrified tiles dado/ skirting of 1st quality tiles of approved size, colour & make including providing 14 mm thick cement sand bedding mortar and each tile plastered on the back side with neat cement slurry before fixing to the bedding mortar including filling and finishing of all joints with white cement paste with matching pigments and cleaning with saw dust and dilute sulphuric acid, curing etc as per specifications and directions of the Engineer/Consultant. a) minimum 8/10 mm thick vitrified tiles

I-12 Supplying and laying 40 mm thick at floor and tread of staircase finish with 25 mm thick Kota stone slab of uniform colour on 15 mm thick cement sand bedding mortar and jointing with cement grout and matching pigment including curing, polishing complete in all respect as per specifications and directions of the Engineer/Consultant.

I-13 Supplying and laying 30 mm thick dado /skirting / at riser of staircase/window sill with 20 mm thick Kota stone slab, polished, machine cut edges of uniform colour fixed with 10 mm thick cement sand bedding of mortar and jointing with cement grout with matching pigments including curing, polishing, complete in all respect all as per specifications and directions of the Engineer/Consultant.

I-14 Supplying and fixing 40 mm thick marble flooring at floor and treads of staircase with 18 mm thick marble slab / tile of approved shades and texture laid with vein matching, set in 15 mm thick mortar of cement and coarse sand laid, polished, filling the joints with white cement to floor, including machine cutting of the slab, rubbing, curing, cleaning, polishing all as per specification and direction of the Engineer/Consultant

I-15 Supplying & laying marble skirting/dado with 18 mm thick marble slab of approved shade and texture laid with 10 mm thick cement sand mortar, cement floated, laid, polished, filling the joints with white cement including machine cutting of the slab, rubbing, curing, cleaning, polishing all as per specification and direction of the Engineer/Consultant

I-16 Supplying and laying 40 mm thick floor with 5 mm thick acid/alkali/chemical resistant non-skid epoxy concrete finish over 35 mm thick screed concrete base laid to slope all as per manufacturer's specification and direction of the Engineer/Consultant.

I-17 Supplying and laying acid/alkali/chemical resistant epoxy skirting/dado over plastered surface all as per attached manufacturer's specification and direction of the Engineer/Consultant.

I-18 Providing trowel finish with neat cement slurry on green plastered/ concrete surface of floors, ramps, steps etc. to the correct slope, line & level as per specifications and directions of the Engineer/Consultant.

I-19 Making saucer drain upto 300 mm deep finished with neat cement slurry on green concrete surface of floors in the basement, tunnels, slab etc to correct slope, line and level including curing, shuttering for forming shape of saucer, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Measurement and payment shall be based on plan area)

I-20 Supplying and fixing 50 mm thick precast PCC interlocking paving tiles at finished ground level as per specification and direction of the Engineer/Consultant. Grade of precast paver blocks is M30.

I-21 Supplying & fixing Coloured glass mosaic tile to external finishes at all heights 20mm X 20mm X4mm thick in 305mm X 305 mm paper sheet and to be fixed to the plastered wall surface by adhesive as per manufacturer’s specification and as approved by Engineer/ Consultant

I-22 Supplying and fixing External quality ceramic tiles ‘Eurocon’ or approved equivalent external wall cladding ceramic tiles at all heights to be fixed as per manufacturer’s specification and as per the direction of the Engineer/Consultant

I-23 Supplying and laying of chequered precast cement concrete tiles of 22 mm thick in footpath, walkway, pavement etc of approved make and shade, jointed with neat cement slurry mixed with colour pigments to match the shade of tiles including rubbing, cleaning, curing etc over 20 mm thick 1:4 cement sand mortar bed, as directed by Engineer/Consultant, all materials, tools, plant, labour complete in all respect

I -24 Supplying, providing and fixing of False flooring with panels of size 600 X 600 mm and Sub Structure installed to support the panel shall be at finished floor height of 600mm from the existing floor level using pedestals and stingers. The floor panels shall be completely removable and shall remain in position without screwing or bolting. The joints between finished floor panels shall be without any gap. The floor panels shall be suitable for cutting whenever required for providing suitable outlets for cables, etc. The panel shall be laminated with anti-static laminate of approved shade and colour, all as per manufacturer's specification and direction of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

DOORS, WINDOWS, PARTITION AND FALSE CEILING

J-1 Supplying and fixing well seasoned, ASCU treated salwood or approved equivalent wooden door frames of all sizes including applying one coat of coal tar over the surface in contact with masonry/concrete with holdfasts all screws, wedges, keys, nails etc and cutting/ drilling of necessary holes in masonry/concrete and grouting of holdfasts with (1:2) cement sand mortar, all as per specifications and directions of the Engineer/Consultant.

J-2(i) Supplying, fabricating and fixing single or double leaf door shutters (Glazed or non Glazed) of the following types made of kiln seasoned and ASCU treated "Hollock" or approved quality hardwood including necessary hardware includes hinges, locks and cleats etc., all as per attached specifications and directions of the Engineer/Consultant (glazing shall be measured separately): a) Wooden panelled door shutter with cement bonded particle board, panel insert conforming to IS:14276

J-2(i) Supplying, fabricating and fixing single or double leaf door shutters (Glazed or non Glazed) of the following types made of kiln seasoned and ASCU treated "Hollock" or approved quality hardwood including necessary hardware includes hinges, locks and cleats etc., all as per attached specifications and directions of the Engineer/Consultant (glazing shall be measured separately): b) Same as in item J-2 (i) a) above but with fully glazed shutter.

J-2(i) Supplying, fabricating and fixing single or double leaf door shutters (Glazed or non Glazed) of the following types made of kiln seasoned and ASCU treated "Hollock" or approved quality hardwood including necessary hardware includes hinges, locks and cleats etc., all as per attached specifications and directions of the Engineer/Consultant (glazing shall be measured separately): c) Same as in item J-2 (i) a) above but with partly panelled and partly glazed shutter

J-2(ii) Supplying, fabricating and fixing in position single/double leaf door shutters (glazed or non glazed) of the following type made of exterior grade medium density fibre board (MDF) conforming to IS:12406-1988 of approved make including necessary hardware (glazing shall be measured separately) all as per specifications and directions of the Engineer/Consultant: a) Panelled door shutter with Medium Density Fibre (MDF) stiles & rails, panel inserts conforming to IS:12406.

J-2(ii) Supplying, fabricating and fixing in position single/double leaf door shutters (glazed or non glazed) of the following type made of exterior grade medium density fibre board (MDF) conforming to IS:12406-1988 of approved make including necessary hardware (glazing shall be measured separately) all as per specifications and directions of the Engineer/Consultant: b) Same as in item J-2(ii) a) above but with fully glazed shutter

J-2(ii) Supplying, fabricating and fixing in position single/double leaf door shutters (glazed or non glazed) of the following type made of exterior grade medium density fibre board (MDF) conforming to IS:12406-1988 of approved make including necessary hardware (glazing shall be measured separately) all as per specifications and directions of the Engineer/Consultant: c) Same as in item J-2(ii) a) above but with partly panelled and partly glazed shutter.

J-3 (i) Supplying, fabricating and fixing single/double leaf flush door shutters (Glazed or non Glazed) of the following types including all necessary hardware, all as per attached specifications and directions of the Engineer/Consultant (glazing shall be measured separately): a) Approved commercial quality solid core block board flush door shutter confirming to IS:2202

J-3 (i) Supplying, fabricating and fixing single/double leaf flush door shutters (Glazed or non Glazed) of the following types including all necessary hardware, all as per attached specifications and directions of the Engineer/Consultant (glazing shall be measured separately): b) Same as in item J-3 (i) a) above but with vision glass

J-3 (i) Supplying, fabricating and fixing single/double leaf flush door shutters (Glazed or non Glazed) of the following types including all necessary hardware, all as per attached specifications and directions of the Engineer/Consultant (glazing shall be measured separately): c) Same as in item J-3 (i) a) above but with seasoned hardwood louvres

J-3 (ii) Supplying, fabricating and fixing in position single/double leaf flush door shutters (glazed or non glazed) of the following type made of exterior grade medium density fibre board (MDF) conforming to IS:12406-1988 of approved make including necessary hardware (glazing shall be measured separately) all as per specifications and directions of the Engineer/ Consultant: a) Approved exterior grade Medium Density Fibre (MDF) board

J-3 (ii) Supplying, fabricating and fixing in position single/double leaf flush door shutters (glazed or non glazed) of the following type made of exterior grade medium density fibre board (MDF) conforming to IS:12406-1988 of approved make including necessary hardware (glazing shall be measured separately) all as per specifications and directions of the Engineer/ Consultant: b) Same as in item J-3 (ii) a) above but with vision glass.

J-4 Supplying, fitting & fixing in position fully sheeted single/double leaf pre-coated pressed steel panel door Glazed or Non Glazed (base steel as per IS:513 "D" quality, galvanised as per IS:277 with zinc of 120 GM/Sq M with total coating thickness 0.55 to 0.6mm) with Pressed steel frame and CRCA sheet welded to frame work as shutter including all necessary fittings and fixtures including cutting /drilling necessary holes in walls/concrete & grouting of lugs in the same with (M20) cement concrete all as per attached specifications & direction of Engineer/Consultants (glazing shall be measured separately): a) Fully glazed pressed steel doors

J-4 Supplying, fitting & fixing in position fully sheeted single/double leaf pre-coated pressed steel panel door Glazed or Non Glazed (base steel as per IS:513 "D" quality, galvanised as per IS:277 with zinc of 120 GM/Sq M with total coating thickness 0.55 to 0.6mm) with Pressed steel frame and CRCA sheet welded to frame work as shutter including all necessary fittings and fixtures including cutting /drilling necessary holes in walls/concrete & grouting of lugs in the same with (M20) cement concrete all as per attached specifications & direction of Engineer/Consultants (glazing shall be measured separately): b) Air tight pressed steel doors with fully sheeted & with rubber Strip glued to shutter & door frame all round.

J-5 Supplying, fitting & fixing in position fully sheeted single/double leaf pre-coated pressed steel flush door Glazed or Non Glazed including all necessary fittings and fixtures including cutting /drilling necessary holes in walls/ concrete & grouting of lugs in the same with (M20) cement concrete all as per attached specifications & direction of Engineer/Consultants (glazing shall be measured separately):Approximate size of doors shall be single leaf doors are 750 x 2100 and 1200 x 2400. Double leaf door sizes are 1200 x 2100 and 1500 x 2400. a) Pressed steel flush door

J-5 Supplying, fitting & fixing in position fully sheeted single/double leaf pre-coated pressed steel flush door Glazed or Non Glazed including all necessary fittings and fixtures including cutting /drilling necessary holes in walls/ concrete & grouting of lugs in the same with (M20) cement concrete all as per attached specifications & direction of Engineer/Consultants (glazing shall be measured separately):Approximate size of doors shall be single leaf doors are 750 x 2100 and 1200 x 2400. Double leaf door sizes are 1200 x 2100 and 1500 x 2400. b) Pressed steel flush door with vision panel

J-5 Supplying, fitting & fixing in position fully sheeted single/double leaf pre-coated pressed steel flush door Glazed or Non Glazed including all necessary fittings and fixtures including cutting /drilling necessary holes in walls/ concrete & grouting of lugs in the same with (M20) cement concrete all as per attached specifications & direction of Engineer/Consultants (glazing shall be measured separately):Approximate size of doors shall be single leaf doors are 750 x 2100 and 1200 x 2400. Double leaf door sizes are 1200 x 2100 and 1500 x 2400. c) Pressed steel flush door with louvre

J-5 Supplying, fitting & fixing in position fully sheeted single/double leaf pre-coated pressed steel flush door Glazed or Non Glazed including all necessary fittings and fixtures including cutting /drilling necessary holes in walls/ concrete & grouting of lugs in the same with (M20) cement concrete all as per attached specifications & direction of Engineer/Consultants (glazing shall be measured separately):Approximate size of doors shall be single leaf doors are 750 x 2100 and 1200 x 2400. Double leaf door sizes are 1200 x 2100 and 1500 x 2400. d) Pressed steel flush door with vision glass and louvre.

J-5 Supplying, fitting & fixing in position fully sheeted single/double leaf pre-coated pressed steel flush door Glazed or Non Glazed including all necessary fittings and fixtures including cutting /drilling necessary holes in walls/ concrete & grouting of lugs in the same with (M20) cement concrete all as per attached specifications & direction of Engineer/Consultants (glazing shall be measured separately):Approximate size of doors shall be single leaf doors are 750 x 2100 and 1200 x 2400. Double leaf door sizes are 1200 x 2100 and 1500 x 2400. e) Pressed steel airtight door with rubber strip glued to shutter & door frame all round

J-6 Supplying, fitting and fixing in position standard single / double leaf steel door with shutters and frame, vision panel etc. with all fittings and fixtures including cutting/drilling necessary holes in walls/concrete and grouting of lugs in the same with (M20) cement concrete, as per specifications and directions of the Engineer/Consultant (glazing shall be measured separately): a) Fully sheeted steel door

J-6 Supplying, fitting and fixing in position standard single / double leaf steel door with shutters and frame, vision panel etc. with all fittings and fixtures including cutting/drilling necessary holes in walls/concrete and grouting of lugs in the same with (M20) cement concrete, as per specifications and directions of the Engineer/Consultant (glazing shall be measured separately): b) Fully sheeted steel door with vision panel

J-6 Supplying, fitting and fixing in position standard single / double leaf steel door with shutters and frame, vision panel etc. with all fittings and fixtures including cutting/drilling necessary holes in walls/concrete and grouting of lugs in the same with (M20) cement concrete, as per specifications and directions of the Engineer/Consultant (glazing shall be measured separately): c) Fully sheeted steel airtight door with rubber strip glued to shutter & door frame all round

J-7 Supplying, fitting and fixing in position aluminium single/double leaf doors of approved make including single/ double action floor spring and pivot and all other fittings and fixtures as per attached specifications and directions of the Engineer/ Consultant (glazing shall be measured separately): a) i) Fully glazed aluminium door

J-7 Supplying, fitting and fixing in position aluminium single/double leaf doors of approved make including single/ double action floor spring and pivot and all other fittings and fixtures as per attached specifications and directions of the Engineer/ Consultant (glazing shall be measured separately): a) ii) Fully glazed sliding aluminium door

J-7 Supplying, fitting and fixing in position aluminium single/double leaf doors of approved make including single/ double action floor spring and pivot and all other fittings and fixtures as per attached specifications and directions of the Engineer/ Consultant (glazing shall be measured separately): b) Item J-7(a) above but with exterior grade medium density fibre board (MDF) panel inserts conforming to IS:12406

J-7 Supplying, fitting and fixing in position aluminium single/double leaf doors of approved make including single/ double action floor spring and pivot and all other fittings and fixtures as per attached specifications and directions of the Engineer/ Consultant (glazing shall be measured separately): c) Partly glazed and partly panelled using panel inserts: (i) medium density fibre board conforming to IS: 14206

J-8 Supplying, erecting and fixing in position pressed steel fully glazed/fully panelled/partly glazed and partly panelled with pre-coated coloured CRCA sheet frames framework including necessary fitting and fixtures as per specifications and directions of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). a) fully panelled partition wall with i) cement bonded particle board conforming to IS:14276

J-8 Supplying, erecting and fixing in position pressed steel fully glazed/fully panelled/partly glazed and partly panelled with pre-coated coloured CRCA sheet frames framework including necessary fitting and fixtures as per specifications and directions of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). a) fully panelled partition wall with ii) medium density fibre board (MDF) conforming to IS:12406

J-8 Supplying, erecting and fixing in position pressed steel fully glazed/fully panelled/partly glazed and partly panelled with pre-coated coloured CRCA sheet frames framework including necessary fitting and fixtures as per specifications and directions of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). b) Fully glazed partition wall with 6 mm thk clear float glass for partitions & 6 mm thick clear toughened glass for doors

J-8 Supplying, erecting and fixing in position pressed steel fully glazed/fully panelled/partly glazed and partly panelled with pre-coated coloured CRCA sheet frames framework including necessary fitting and fixtures as per specifications and directions of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). c) Partly pannelled and partly glazed partition wall using panel inserts: i) medium density fibre board (MDF) conforming to IS:12406

J-9 Supplying, erecting and fixing in position aluminium framed fully glazed/fully panelled/partly glazed and partly panelled partition wall with anodised aluminium extruded sections of approved make including necessary fitting and fixtures as per specification and direction of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). a) fully panelled partition wall using panel inserts: i) cement bonded particle board conforming to IS:14276

J-9 Supplying, erecting and fixing in position aluminium framed fully glazed/fully panelled/partly glazed and partly panelled partition wall with anodised aluminium extruded sections of approved make including necessary fitting and fixtures as per specification and direction of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). a) fully panelled partition wall using panel inserts: ii) medium density fibre board (MDF) conforming to IS:12406

J-9 Supplying, erecting and fixing in position aluminium framed fully glazed/fully panelled/partly glazed and partly panelled partition wall with anodised aluminium extruded sections of approved make including necessary fitting and fixtures as per specification and direction of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). b) Fully glazed partition wall with 6 mm thk clear float glass for partitions & 6 mm thick clear toughened glass for doors

J-9 Supplying, erecting and fixing in position aluminium framed fully glazed/fully panelled/partly glazed and partly panelled partition wall with anodised aluminium extruded sections of approved make including necessary fitting and fixtures as per specification and direction of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). c) Partly pannelled and partly glazed partition wall using panel inserts: i) cement bonded particle board conforming to IS:14276

J-9 Supplying, erecting and fixing in position aluminium framed fully glazed/fully panelled/partly glazed and partly panelled partition wall with anodised aluminium extruded sections of approved make including necessary fitting and fixtures as per specification and direction of the Engineer/Consultant. (doors will be paid as per relevant item of BOQ and will be measured as per area of the door panel). c) Partly pannelled and partly glazed partition wall using panel inserts: ii) medium density fibre board (MDF) conforming to IS:12406

J-10a) Supplying, fitting and fixing low height partition wall made of pressed steel frames and cement bonded particle board confirming to IS:14276 fixed by steel beads framework, all as per attached specification and direction of the Engineer/Consultant.

J-10b) Same as item J-10 a) above but with medium density fibre board (MDF) confirming to IS:12406

J-11 Supplying, fitting and fixing in position fixed type single glazed aluminium observation windows with anodised natural colour extended aluminium sections including all fittings and fixtures complete of following types: a) 6 mm thick clear float glass

J-11 Supplying, fitting and fixing in position fixed type single glazed aluminium observation windows with anodised natural colour extended aluminium sections including all fittings and fixtures complete of following types: b) 6 mm thick clear toughened heat resistant glass

J-12 Supplying, fitting and fixing in position fixed type double glazed aluminium observation windows with anodised natural colour extruded aluminium sections all as per attached including all fittings and fixtures complete of the following type: a) 6 mm thick clear toughened heat resistant double glass

J-13 Supplying, fitting and fixing in position aluminium windows and ventilators (fixed/openable/sliding type) 4mm thk. float glass of approved make with frames and shutters of standard anodised aluminium sections including handles, locking arrangement, stays, all as per attached specifications and directions of the Engineer a) Fully glazed side hung window

J-13 Supplying, fitting and fixing in position aluminium windows and ventilators (fixed/openable/sliding type) 4mm thk. float glass of approved make with frames and shutters of standard anodised aluminium sections including handles, locking arrangement, stays, all as per attached specifications and directions of the Engineer b) Fully glazed centre hung ventilator

J-13 Supplying, fitting and fixing in position aluminium windows and ventilators (fixed/openable/sliding type) 4mm thk. float glass of approved make with frames and shutters of standard anodised aluminium sections including handles, locking arrangement, stays, all as per attached specifications and directions of the Engineer c) Fully glazed sliding window

J-14 Supplying, fitting and fixing in position pressed steel windows and ventilators (fixed/openable/sliding type) fabricated from roll formed sections made of galvanised steel colour coated/powder coated All steel sections shall have a primer coat with epoxy primer of 5-7 microns thick finished with a polyester paint of 12-16 microns thick and back coated with alkyd lacquer of 5-7 microns or powder coated with pure polyester powder upto to 50-60 microns thick, including supplying, fitting and fixing in position 4 mm thick float glass to windows and ventilators of approved quality including glazing putty, glazing clips, handle, locking arrangements, stays etc. all as per attached specifications and directions of the Engineer/Consultant. (glazing will be measured separately and paid under relevant item of BOQ) a) Fully glazed side hung window

J-14 Supplying, fitting and fixing in position pressed steel windows and ventilators (fixed/openable/sliding type) fabricated from roll formed sections made of galvanised steel colour coated/powder coated All steel sections shall have a primer coat with epoxy primer of 5-7 microns thick finished with a polyester paint of 12-16 microns thick and back coated with alkyd lacquer of 5-7 microns or powder coated with pure polyester powder upto to 50-60 microns thick, including supplying, fitting and fixing in position 4 mm thick float glass to windows and ventilators of approved quality including glazing putty, glazing clips, handle, locking arrangements, stays etc. all as per attached specifications and directions of the Engineer/Consultant. (glazing will be measured separately and paid under relevant item of BOQ) b) Fully glazed centre ventilator

J-14 Supplying, fitting and fixing in position pressed steel windows and ventilators (fixed/openable/sliding type) fabricated from roll formed sections made of galvanised steel colour coated/powder coated All steel sections shall have a primer coat with epoxy primer of 5-7 microns thick finished with a polyester paint of 12-16 microns thick and back coated with alkyd lacquer of 5-7 microns or powder coated with pure polyester powder upto to 50-60 microns thick, including supplying, fitting and fixing in position 4 mm thick float glass to windows and ventilators of approved quality including glazing putty, glazing clips, handle, locking arrangements, stays etc. all as per attached specifications and directions of the Engineer/Consultant. (glazing will be measured separately and paid under relevant item of BOQ) c) Fully glazed sliding window

J-15 Supplying, fitting and fixing in position glazing to doors, windows and ventilators as specified of approved quality clear / toughened float glass, including glazing putty, glazing clips etc, all as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing will be measured on the basis of individual glass pane size as specified in IS:1038): i) 4 mm thick clear float glass of approved quality

J-15 Supplying, fitting and fixing in position glazing to doors, windows and ventilators as specified of approved quality clear / toughened float glass, including glazing putty, glazing clips etc, all as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing will be measured on the basis of individual glass pane size as specified in IS:1038): ii) 6 mm thick clear float glass of approved quality

J-15 Supplying, fitting and fixing in position glazing to doors, windows and ventilators as specified of approved quality clear / toughened float glass, including glazing putty, glazing clips etc, all as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing will be measured on the basis of individual glass pane size as specified in IS:1038): iii) 6 mm thick toughened float glass

J-16 Supplying, fitting & fixing in position approved quality single/ insulated double glazing to external doors, windows etc with clear/tinted float glass (standard/toughned) having thermal conductivity maximum 1.7 W/sq m/k, UV resistant, high visual light transmittance (80%) of approved make, including glazing clips etc. All as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing shall be measured on the basis of individual glass pane size as specified in IS:1038) a) Single glazing: i) 4 mm thick clear float glass

J-16 Supplying, fitting & fixing in position approved quality single/ insulated double glazing to external doors, windows etc with clear/tinted float glass (standard/toughned) having thermal conductivity maximum 1.7 W/sq m/k, UV resistant, high visual light transmittance (80%) of approved make, including glazing clips etc. All as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing shall be measured on the basis of individual glass pane size as specified in IS:1038) a) Single glazing: ii) 4 mm thick tinted float glass

J-16 Supplying, fitting & fixing in position approved quality single/ insulated double glazing to external doors, windows etc with clear/tinted float glass (standard/toughned) having thermal conductivity maximum 1.7 W/sq m/k, UV resistant, high visual light transmittance (80%) of approved make, including glazing clips etc. All as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing shall be measured on the basis of individual glass pane size as specified in IS:1038) a) Single glazing: iii) 6 mm thick clear toughned glass

J-16 Supplying, fitting & fixing in position approved quality single/ insulated double glazing to external doors, windows etc with clear/tinted float glass (standard/toughned) having thermal conductivity maximum 1.7 W/sq m/k, UV resistant, high visual light transmittance (80%) of approved make, including glazing clips etc. All as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing shall be measured on the basis of individual glass pane size as specified in IS:1038) a) Single glazing: iv) 6 mm thick tinted toughned glass

J-16 Supplying, fitting & fixing in position approved quality single/ insulated double glazing to external doors, windows etc with clear/tinted float glass (standard/toughned) having thermal conductivity maximum 1.7 W/sq m/k, UV resistant, high visual light transmittance (80%) of approved make, including glazing clips etc. All as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing shall be measured on the basis of individual glass pane size as specified in IS:1038) b) Insulated double glazing: i) comprising of two 6 mm thick clear float glass hermitically factory sealed together with an air gap of 20 mm in between

J-16 Supplying, fitting & fixing in position approved quality single/ insulated double glazing to external doors, windows etc with clear/tinted float glass (standard/toughned) having thermal conductivity maximum 1.7 W/sq m/k, UV resistant, high visual light transmittance (80%) of approved make, including glazing clips etc. All as per specifications and directions of the Engineer/Consultant, plant and labour complete in all respect (glazing shall be measured on the basis of individual glass pane size as specified in IS:1038) b) Insulated double glazing: ii) Same as item 16 b) (i) but with tinted float glass

J-17 Supplying, fitting and fixing 4 lever mortice latch and lock of "Godrej" make or approved equivalent with keys in duplicate to wooden door shutters including chromium plated brass and face plates with necessary screws etc, all as per specifications and directions of the Engineer/Consultant: a) Plain

J-17 Supplying, fitting and fixing 4 lever mortice latch and lock of "Godrej" make or approved equivalent with keys in duplicate to wooden door shutters including chromium plated brass and face plates with necessary screws etc, all as per specifications and directions of the Engineer/Consultant: b) Rebated

J-18 Supplying and fitting single / double leaf fire check doors with door frames made of 1.6 mm galvanised steel sheet and shutter made of 1.25 mm galvanised steel (both in pressed formed) to provide double spin flush door. Internal reinforcement to be provided for three (3) hours fire ratings as per manufacturer's specification and direction of the Engineer/Consultant.

J-19 Supplying and fixing in position False Ceiling boards fixed with aluminium grids and providing cut outs for lighting fittings and ventilation grills as per specification and the direction of the Engineer/Consultant, including supplying and fixing all fittings and fixtures (The rate should include the cost for supplying and fixing suspenders) Note: 1. Grid shall be 610x610mm and Aluminium T- sections are used for the grid. Aluminium T-section of size 30mm x 35mm and 1.2mm thick shall be used.2. Suspenders can be either 8 swg G.I. wire or 0.7 x 12 mm G.I. flats. The maximum distance allowed between suspenders in longitudinal direction and cross direction is 1220 mm. Closer intervals may be adopted depending on the soffit conditions.It is necessary to introduce a turn buckle in the suspender for easy and faster leveling of the grid. Ordinary G.I. J bolt can serve as turn buckle. i) with 6 mm thick cement bonded particle board conforming to IS:14276

J-20 Supplying and providing in position composite under deck thermal insulation to soffit of roof slab with Gypsum board topping and glass wool underlayer as per attached specification and direction of the Engineer/Consultant. a) With false ceiling

J-20 Supplying and providing in position composite under deck thermal insulation to soffit of roof slab with Gypsum board topping and glass wool underlayer as per attached specification and direction of the Engineer/Consultant. b) Without false ceiling

J-21 Supplying, fabricating and fixing in position welded mesh screen of 5 mm hard drawn steel wire having 75 mm x 50 mm mesh size conforming to No.A-2/16 of IS:4948-1974, welded to M.S. framing angles, channels, flats etc including M.S. holdfasts and cutting necessary holes and grouting of lugs in the same with (1:2) cement mortar and applying painting with one coat of approved primer conforming to IS:2074 and two coats of ready mixed approved synthetic enamel paint, all as per specifications and directions of the Engineer/Consultant. (only net sheet area shall be measured in this item. Steel framing will be measured and paid separately)

J-22 Supplying, fitting and fixing in position Indian Standard steel windows and ventilators with frames and shutters of different types according to IS:1038 with all joints flush butt welded including coupling bars for composite windows and ventilators with heavy duty brass handles and peg stays and all other steel fittings and fixtures like hinges, lugs, stoppers etc and including cutting/drilling necessary holes in walls etc and grouting lugs in the same with (1:2) cement sand mortar and finishing neatly, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect: a) Openable type

J-22 Supplying, fitting and fixing in position Indian Standard steel windows and ventilators with frames and shutters of different types according to IS:1038 with all joints flush butt welded including coupling bars for composite windows and ventilators with heavy duty brass handles and peg stays and all other steel fittings and fixtures like hinges, lugs, stoppers etc and including cutting/drilling necessary holes in walls etc and grouting lugs in the same with (1:2) cement sand mortar and finishing neatly, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect: b) Fixed type

J-23 Supplying, fabricating and welding of M.S guard bars 10 mm square section at maximum spacing of 125 mm c/c with 19 mm x 5 mm M.S. flat fixed to masonry wall at a distance of 75 mm on the inside face of steel window frame and as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

J-24 Supplying, fitting and fixing in position approved quality M.S. rolling shutters conforming to IS: 6248, pull and push type of fully sheeted/partly sheeted partly grilled/fully grilled types as specified with all accessories, side guides, 20 gauge hood cover of hexagonal shape, locking arrangement, handles to operate rolling shutters, rolling grills of following types including cutting necessary holes in walls and grouting with (M20) cement concrete and finishing neatly all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (measurement of rolling shutters shall be the same as that of clear wall opening) a) Gear/chain-pully operated

J-24 Supplying, fitting and fixing in position approved quality M.S. rolling shutters conforming to IS: 6248, pull and push type of fully sheeted/partly sheeted partly grilled/fully grilled types as specified with all accessories, side guides, 20 gauge hood cover of hexagonal shape, locking arrangement, handles to operate rolling shutters, rolling grills of following types including cutting necessary holes in walls and grouting with (M20) cement concrete and finishing neatly all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (measurement of rolling shutters shall be the same as that of clear wall opening) b) Electrically operated

J-25 Supplying and fixing Solid PVC door of thickness 30 mm as per the manufacturer's specifications with all materials, tools, tackels and labour complete in all respect.

J-26 Supplying, fitting and fixing in position approved make automatic hydraulic door closer conforming to IS:3564 with all necessary screws, fittings and fixtures, all as per manufacturer's specification and directions of the Engineer/Consultant.

J-27 Providing and fixing of windows, top hung ventilators of NCL soccolor or approved equivalent fabricated from roll formed sections made of Galvanised Steel Colour Coated / Powder Coated (Base Steel as per IS 513 "D" quality, Galvanised as per IS:277 with Zinc of 120 grams/Sq. Mtr) with total coated thickness of 0.60 mm including 5 mm glass with all necessary screws, fittings and fixtures, all as per manufacturer's specification and directions of the Engineer / Consultant.

J-28 Providing and fixing of curtain Glazing of NCL soccolor or approved equivalent fabricated from roll formed sections made of Galvanised Steel Colour Coated / Powder Coated (Base Steel as per IS 513 "D" quality, Galvanised as per IS:277 with Zinc of 120 grams/Sq. Mtr) with total coated thickness of 0.60 mm including 5 mm reflective glass with all necessary screws, fittings and fixtures, all as per manufacturer's specification and directions of the Engineer / Consultant

J-29 Providing and fixing of structural Glazing of NCL soccolor or approved equivalent fabricated from roll formed sections made of Galvanised Steel Colour Coated / Powder Coated (Base Steel as per IS 513 "D" quality, Galvanised as per IS:277 with Zinc of 120 grams/Sq. Mtr) with total coated thickness of 0.8 mm for verticals and with total coated thickness of 0.6 mm for horizontals. The Glass holding section made of 304 grade stainless steel of 0.6 mm thick. G.I. sections are to be used as stiffeners inside the CCS/PC section as per the design requirement Design calculations are to be made to suit wind pressure as given in IS:875 including 5 mm reflective glass with all necessary screws, fittings and fixtures, all as per manufacturer's specification and directions of the Engineer / Consultant

J-30 Providing and fixing of sliding systems of NCL soccolor or approved equivalent fabricated from roll formed sections made of Galvanised Steel Colour Coated / Powder Coated (Base Steel as per IS 513 "D" quality, Galvanised as per IS:277 with Zinc of 120 grams/Sq. Mtr) with total coated thickness of 0.60 mm with all necessary screws, fittings and fixtures all as per manufacturer's specification and directions of the Engineer / Consultant

WATERPROOFING

K-1 Providing waterproofing to base, walls & vertical faces of underground structures as specified hereunder with a guarantee of waterproofing for a period of ten (10) years supply of all materials and labour complete in all respect: a) Supplying and applying two coats of cementitious compound Sika Top 77/Cemflex/ Tapelastic of SWC/Hindcrete plus WPM/ Tapecrete P151 of CICO or approved equivalent according to manufacturer's instructions over concrete surfaces including rectification of any defects in concrete surfaces by rendering with (1:3) cement sand mortar before application of the approved cementitious compound

K-1 Providing waterproofing to base, walls & vertical faces of underground structures as specified hereunder with a guarantee of waterproofing for a period of ten (10) years supply of all materials and labour complete in all respect: b) Supplying, placing and fixing 15 mm dia G.S. threaded nozzles having a minimum thickness of 16 gauge (medium quality) of suitable length in approximate grid pattern of 1.5 m c/c prior to or during concreting in base, walls and vertical faces of under- ground structures and also providing 15 mm dia G.S threaded nozzles at regular intervals not exceeding 1.5 m c/c along construction joints and at critical joints as directed, plugging both ends of the nozzles to prevent ingress of foreign materials all as per specification and as directed by the Engineer/Consultant.

K-1 Providing waterproofing to base, walls & vertical faces of underground structures as specified hereunder with a guarantee of waterproofing for a period of ten (10) years supply of all materials and labour complete in all respect: c) Supplying and adding plasticiser-cum-waterproofing compound Sikament-277 of Sika/Supaplast - HS of SWC/Conplast P211(M) of Fosroc/Cico Supaplast or approved equivalent in concrete as per manufacturers instructions and specifications and as directed by the Engineer/Consultant (Payment will be made on the volume of concrete)

K-1 Providing waterproofing to base, walls & vertical faces of underground structures as specified hereunder with a guarantee of waterproofing for a period of ten (10) years supply of all materials and labour complete in all respect: d) Injecting Intraplast N-200 of Sika/Excem-C of SWC/Cebex 100 of Fosroc/Cico non-shrink polymeric waterproof grouting compound or approved equivalent and mixed with cement slurry through the nozzles set in the base, walls and vertical faces of concrete under pressure by pump and finally sealing off the nozzles after the injection operation is over with Sika 4a/Struco-3 of SWC/Renderoc Plug of Fosroc/ Cico quick setting admixture or approved equivalent all as per instructions of the manufacturer and as directed by the Engineer/Consultant.

K-2 Supplying waterproofing to roof slab with a guarantee of water proofing for a period of ten (10) years, all as per manufacturer's specifications, and directions of the Engineer/Consultant, all materials, labour complete in all respect: (a) Supplying and laying of fibre glass cloth over acrylic polymer modified cementitious water proofing compound Sika Top Seal 107/Brush Bond/Tapecrete P151 or approved equivalent laid over roof slab and including overlaping in parapet wall rendered with (1:4) cement sand mortar and protected by a layer of screed concrete (M15) admixed with Sika Plasto Crete plus/CICO No. 1/Conplast X 421IC laid in slope underlaid by a layer of acrylic polymer modified cementitious water proofing compound same as above true to specification and as directed by Engineer/Consultant, with all ancillary civil work with all materials, tools, labour complete in all respect. Note: The contractor will be asked to submit the warranty certificate of the supplier.

K-3 Supplying and painting one coat of approved hot bitumen using 1.5 kg/sq m of 20/30 grade bitumen as per IS:702 for water proofing on all concrete/plastered surfaces at all depths below ground level including a coat of approved bituminous primer as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect

K-4 Extra over item M-3 above for each coat of hot bitumen paint using 1.2 kg/sq m of bitumen

SANITARY AND PLUMBING Note: The rates to include the cost of cutting chases and holes in brickwork, rubble masonry, concrete, plaster etc for embedding or passing pipes, fixing brackets, fitting and making good the damages to the original condition wherever necessary, also the rates should include the cost of cutting, bending, threading, jointing etc of pipe works and applying one coat of single pack air drying heavy duty anti- corrosive bituminous paint to the inside of cast iron soil, waste, vent and rainwater pipes and fittings.

L-1 Supplying, laying, fitting and fixing the following sanitary items including all pipe works, fittings, joints and other necessary items to run the system successfully a) Supplying, fitting and fixing white glazed earthenware European type water closet of Jaquar/Parryware/ Hindware make no. 225/226 or other approved equivalent make with “P” or “S” trap with or without vent hole, colour or black solid plastic seat and cover with low level similine polymer cistern of 10 litres capacity with anti-microbial front knob of Jaquar/ Parryware/ Hindware make No. 8090/8091 or other approved equivalent as directed by the Engineer as specified all fittings materials, tools and labour complete.

L-1 Supplying, laying, fitting and fixing the following sanitary items including all pipe works, fittings, joints and other necessary items to run the system successfully b) Supplying, fitting and fixing in position white glazed earthenware Indian type water closet comprising of 580 mm long “Orissa Pan” of Jaquar/ Parryware/ Hindware make no. 0109 or other approved equivalent make with slimline polymer cistern of 10 litres capacity with anti-microbial front knob of Jaquar/Parryware/ Hindware make No.8090/8091 or other approved equivalent as directed by the Engineer as specified all fittings materials, tools and labour complete.

L-1 Supplying, laying, fitting and fixing the following sanitary items including all pipe works, fittings, joints and other necessary items to run the system successfully c) Supplying, fitting and fixing in position white glazed vitreous new magnum urinal of Jaquar/Parryware/ Hindware or approved equivalent fixed on wall with “Z” concealed brackets with bottle trap at the bottom, screws, wooden gutties, stopcock, connector, wastepipe etc all as per specifications and the directions of Engineer all materials, tools and labour complete.

L-1 Supplying, laying, fitting and fixing the following sanitary items including all pipe works, fittings, joints and other necessary items to run the system successfully d) Supplying, fitting and fixing white glazed vitreous China wash basin of Jaquar/Parryware/ Hindware with central tap hole including supplying and fixing of C.I. brackets painted with two coats of approved red oxide zinc chromate primer and two coats of approved synthetic enamel paint, 15 mm dia chromium plated approved deluxe head pillar tap, 32 mm dia chromium plated heavy duty approved waste fittings, chain rubber plug etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect i) 550 mm x 400 mm

L-1 Supplying, laying, fitting and fixing the following sanitary items including all pipe works, fittings, joints and other necessary items to run the system successfully d) Supplying, fitting and fixing white glazed vitreous China wash basin of Jaquar/Parryware/ Hindware with central tap hole including supplying and fixing of C.I. brackets painted with two coats of approved red oxide zinc chromate primer and two coats of approved synthetic enamel paint, 15 mm dia chromium plated approved deluxe head pillar tap, 32 mm dia chromium plated heavy duty approved waste fittings, chain rubber plug etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect ii) 550 mm x 400 mm (Oval).

L-2 Supplying and laying in slope following stoneware pipes conforming to grade I of IS:651 at all depths below plinth level as specified including spigot and socket jointing with joints filled in (1:1) cement mortar with necessary hemp yarn etc, curing joints and testing of pipes as specified in specification, IS:4127 and IS:1200 but excluding excavation, bedding, haunching of concrete and backfilling, all as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect. a) 100 mm dia

L-2 Supplying and laying in slope following stoneware pipes conforming to grade I of IS:651 at all depths below plinth level as specified including spigot and socket jointing with joints filled in (1:1) cement mortar with necessary hemp yarn etc, curing joints and testing of pipes as specified in specification, IS:4127 and IS:1200 but excluding excavation, bedding, haunching of concrete and backfilling, all as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect. b) 150 mm dia

L-2 Supplying and laying in slope following stoneware pipes conforming to grade I of IS:651 at all depths below plinth level as specified including spigot and socket jointing with joints filled in (1:1) cement mortar with necessary hemp yarn etc, curing joints and testing of pipes as specified in specification, IS:4127 and IS:1200 but excluding excavation, bedding, haunching of concrete and backfilling, all as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect. c) 200 mm dia

L-2 Supplying and laying in slope following stoneware pipes conforming to grade I of IS:651 at all depths below plinth level as specified including spigot and socket jointing with joints filled in (1:1) cement mortar with necessary hemp yarn etc, curing joints and testing of pipes as specified in specification, IS:4127 and IS:1200 but excluding excavation, bedding, haunching of concrete and backfilling, all as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect. d) 250 mm dia

L-3 Supplying and fixing 100 mm dia square mouth `P' type salt glazed S.W. gully/yard gully traps Grade-I with 200 mm sq C.I. hinged grating including filling joints with cement mortar (1:1) and necessary hemp yarn, curing etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect

L-4 Supplying, fitting and fixing 150 mm dia salt glazed stoneware master trap with cleaning access and cover conforming to IS:651 inside the pit at all depths below plinth level including joints with cement mortar (1:1) all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-5 Supplying, fitting and fixing with PCC (M-10) C.I. manhole cover and frames conforming to IS:1726 to inspection pits and septic tank, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect a) Medium duty - MD 10 grade

L-5 Supplying, fitting and fixing with PCC (M-10) C.I. manhole cover and frames conforming to IS:1726 to inspection pits and septic tank, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect b) Heavy duty - HD 20 grade

L-6 Supplying, fitting and fixing heavy cast iron (HCI) C.I. soil pipes conforming to IS:1729 of the following sizes at all heights and depths above and below plinth level including caulking joints with lead as specified, clamps, C.I. bobbins, wooden plugs, nails etc and testing of pipes, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: a) 50 mm dia

L-6 Supplying, fitting and fixing heavy cast iron (HCI) C.I. soil pipes conforming to IS:1729 of the following sizes at all heights and depths above and below plinth level including caulking joints with lead as specified, clamps, C.I. bobbins, wooden plugs, nails etc and testing of pipes, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: b) 100 mm dia

L-7 Supplying, fitting and fixing following HCI soil fittings such as junctions, bends, tees, inspection pieces, 'P' or 'S' trap, trap extension piece, WC connector etc at all heights and depths above and below plinth level with or without cleaning, access door, 3 mm thick insertion rubber washer, putting bolts including caulking joints with lead as specified and testing, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: a) 50 mm dia

L-7 Supplying, fitting and fixing following HCI soil fittings such as junctions, bends, tees, inspection pieces, 'P' or 'S' trap, trap extension piece, WC connector etc at all heights and depths above and below plinth level with or without cleaning, access door, 3 mm thick insertion rubber washer, putting bolts including caulking joints with lead as specified and testing, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: b) 100 mm dia

L-8 Supplying, fitting and fixing in position galvanised steel waste pipes of following dia conforming to IS:1239 (medium duty) at all heights and depths above and below plinth level including necessary galvanised steel fittings such as elbows, tees, plugs, sockets, short pieces, H.B. clamps etc and testing of the pipelines all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: a) 32 mm dia

L-8 Supplying, fitting and fixing in position galvanised steel waste pipes of following dia conforming to IS:1239 (medium duty) at all heights and depths above and below plinth level including necessary galvanised steel fittings such as elbows, tees, plugs, sockets, short pieces, H.B. clamps etc and testing of the pipelines all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: b) 40 mm dia

L-9 Supplying, fitting and fixing in position galvanised steel (medium duty) distribution pipes of the following sizes conforming to IS:1239 at all heights and depths above and below plinth level including necessary galvanised steel fittings such as bends, elbows, tees, plugs, sockets, short pieces, clamps etc and testing of the pipe lines hydraulically, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: a) 15 mm dia

L-9 Supplying, fitting and fixing in position galvanised steel (medium duty) distribution pipes of the following sizes conforming to IS:1239 at all heights and depths above and below plinth level including necessary galvanised steel fittings such as bends, elbows, tees, plugs, sockets, short pieces, clamps etc and testing of the pipe lines hydraulically, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: b) 20 mm dia

L-9 Supplying, fitting and fixing in position galvanised steel (medium duty) distribution pipes of the following sizes conforming to IS:1239 at all heights and depths above and below plinth level including necessary galvanised steel fittings such as bends, elbows, tees, plugs, sockets, short pieces, clamps etc and testing of the pipe lines hydraulically, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: c) 25 mm dia

L-9 Supplying, fitting and fixing in position galvanised steel (medium duty) distribution pipes of the following sizes conforming to IS:1239 at all heights and depths above and below plinth level including necessary galvanised steel fittings such as bends, elbows, tees, plugs, sockets, short pieces, clamps etc and testing of the pipe lines hydraulically, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: d) 32 mm dia

L-9 Supplying, fitting and fixing in position galvanised steel (medium duty) distribution pipes of the following sizes conforming to IS:1239 at all heights and depths above and below plinth level including necessary galvanised steel fittings such as bends, elbows, tees, plugs, sockets, short pieces, clamps etc and testing of the pipe lines hydraulically, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: e) 40 mm dia

L-9 Supplying, fitting and fixing in position galvanised steel (medium duty) distribution pipes of the following sizes conforming to IS:1239 at all heights and depths above and below plinth level including necessary galvanised steel fittings such as bends, elbows, tees, plugs, sockets, short pieces, clamps etc and testing of the pipe lines hydraulically, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: f) 50 mm dia

L-10 Supplying, fitting and fixing tested heavy duty (10 Kg/ sq cm) gun metal full way gate valve of approved make, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: a) 15 mm dia

L-10 Supplying, fitting and fixing tested heavy duty (10 Kg/ sq cm) gun metal full way gate valve of approved make, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: b) 20 mm dia

L-10 Supplying, fitting and fixing tested heavy duty (10 Kg/ sq cm) gun metal full way gate valve of approved make, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: c) 25 mm dia

L-10 Supplying, fitting and fixing tested heavy duty (10 Kg/ sq cm) gun metal full way gate valve of approved make, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: d) 32 mm dia

L-10 Supplying, fitting and fixing tested heavy duty (10 Kg/ sq cm) gun metal full way gate valve of approved make, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: e) 40 mm dia

L-10 Supplying, fitting and fixing tested heavy duty (10 Kg/ sq cm) gun metal full way gate valve of approved make, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: f) 50 mm dia

L-11 Supplying, fitting and fixing 15 mm dia chromium plated brass deluxe head approved angular/straight stop cock/ bibcock /foam tap with C.P. wall flange, all as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect.

L-12 Supplying, fitting and fixing approved quality tested high pressure type (10 kg/sq cm) following dia fullway brass ball cock (horizontal plunger type) with polyethylene float of approved make at all heights above plinth level, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: a) 15 mm dia

L-12 Supplying, fitting and fixing approved quality tested high pressure type (10 kg/sq cm) following dia fullway brass ball cock (horizontal plunger type) with polyethylene float of approved make at all heights above plinth level, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: b) 20 mm dia

L-12 Supplying, fitting and fixing approved quality tested high pressure type (10 kg/sq cm) following dia fullway brass ball cock (horizontal plunger type) with polyethylene float of approved make at all heights above plinth level, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: c) 25 mm dia

L-12 Supplying, fitting and fixing approved quality tested high pressure type (10 kg/sq cm) following dia fullway brass ball cock (horizontal plunger type) with polyethylene float of approved make at all heights above plinth level, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: d) 32 mm dia

L-13 Supplying, fitting & fixing in position 15 mm dia heavy PVC connector of required length fitted with C.P. brass heavy coupling nuts and rubber washers at both ends to basins, cisterns etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

L-14 Supplying, fitting and fixing single prong C.P. brass coat hook with C.P. brass screws, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

L-15 Supplying, fitting and fixing in position approved make 125 mm dia chromium plated slotted brass grating over C.I. floor trap including cutting floors, if necessary, and making good etc, all as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect.

L-16 Supplying, fitting and fixing in position and slope 100 mm dia half-round white glazed vitreous China channels of approved make, plain with outlet and stop-end pieces including grouting the channels with PCC of nominal mix (M7.5) by volume and filling joints with white cement etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-17 Supplying, fitting and fixing approved make 550 mm x 400 mm x 5.5 mm thick round edged frameless plate glass mirror with asbestos sheet backing with clips, rubber buffers, C.P. dome headed screws, etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-18 Supplying, fitting and fixing in position SS roll type toilet paper holder of approved make fixed on wall with SS screws etc, all as specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect.

L-19 Supplying, fitting and fixing in position approved SS liquid soap container fixed on wall with C.P. round headed SS screws, wooden gutties, rawl plugs etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-20 Supplying, fitting and fixing in position approved make 600 mm long SS towel rail with brackets fixed with SS screws, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-21 Supplying, hoisting. fitting and fixing in position at all heights above plinth level approved make high density polyethylene double layer, cylindrical, vertical, water storage tanks of following sizes and capacities at all heights above finished ground level with 400 mm dia hinged manhole cover of the same material with provision of float valves at water inlet point and locking arrangement, providing necessary holes for pipe connections etc all materials, tools and labour complete in all respect: a) 750 litres cap

L-21 Supplying, hoisting. fitting and fixing in position at all heights above plinth level approved make high density polyethylene double layer, cylindrical, vertical, water storage tanks of following sizes and capacities at all heights above finished ground level with 400 mm dia hinged manhole cover of the same material with provision of float valves at water inlet point and locking arrangement, providing necessary holes for pipe connections etc all materials, tools and labour complete in all respect: b) 1500 litres cap

L-22 Supplying, fitting and fixing in position `Adanga/Doongri' or other equivalent make white marble stone urinal partition of overall size 700 mm x 575 mm x 18 mm thick with edges and corners shaped round, securely fixed on wall including cutting chase and grouting the same with PCC (M20) and polishing the partition on all sides, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-23 Supplying, fitting and fixing 100 mm x 15 mm dia equivalent round or other approved colour, size and shape shower rose, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: a) Coloured P.V.C.

L-23 Supplying, fitting and fixing 100 mm x 15 mm dia equivalent round or other approved colour, size and shape shower rose, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: b) C.P.

L-24 Supplying, fitting and fixing in position 550 mm x 125 mm x 5.5 mm thick plate glass shelf with chromium plated brass brackets fixed to wall with C.P. brass screws etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-25 Supplying, fitting and fixing in position 500 x 350 x 150 mm deep white glazed fire clay laboratory sink inside laboratory room of `Parryware' make or other approved equivalent including supplying and fixing a pair of CI brackets, 40 mm dia CP waste fittings complete in all respect and applying two coats of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved make to CI brackets, all materials, tools and labour complete in all respect.

L-26 Supplying, fitting & fixing 15 mm dia chromium plated brass self closing tap of approved make all as per specification and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-27 Supplying, fitting & fixing C.I. foot steps for manhole, as per specification and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

L-28 Supplying, fitting and fixing C.I cowl over C.I. Ventilation pipe of following dia. and as directed by Engineer/ Consultant, all materials, tools , plant and labour complete in all respect: a) 50 mm dia

L-28 Supplying, fitting and fixing C.I cowl over C.I. Ventilation pipe of following dia. and as directed by Engineer/ Consultant, all materials, tools , plant and labour complete in all respect: b) 100 mm dia

MISCELLANEOUS

M-1 Supplying, cutting, placing and fixing in position high density polyethylene (HDPE) down pipes conforming to IS:4984 to dispose off rain water at and at all heights and depths above and below finished ground level with joints sealed with white zinc and hemp yarn including all HDPE fittings, such as heads, bends, offsets, swan necks, shoes, bobbins, sockets, M.S. clamps, wooden plugs, nails etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: Class of pipes are PE63, PE80 and PE 100. a) 100 mm dia

M-1 Supplying, cutting, placing and fixing in position high density polyethylene (HDPE) down pipes conforming to IS:4984 to dispose off rain water at and at all heights and depths above and below finished ground level with joints sealed with white zinc and hemp yarn including all HDPE fittings, such as heads, bends, offsets, swan necks, shoes, bobbins, sockets, M.S. clamps, wooden plugs, nails etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: Class of pipes are PE63, PE80 and PE 100. b) 150 mm dia

M-2 Supplying and laying in position cast iron grating in roof for disposal of water as shown in the specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 200 mm dia

M-2 Supplying and laying in position cast iron grating in roof for disposal of water as shown in the specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) 250 mm dia

M-3 Supplying and fixing spouts of Class-B (medium) galvanised steel pipes embedded in concrete/masonry all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 32 x 125 long

M-3 Supplying and fixing spouts of Class-B (medium) galvanised steel pipes embedded in concrete/masonry all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) 50 x 150 long

M-4 Supplying, laying, jointing, fixing and embedding in all types of foundations and super structures Class B (Medium duty) galvanised steel pipes of approved quality conforming to IS:1239/IS:1978 of following diameters with necessary sockets, check nuts, jumpers etc for electrical conduit pipes including threading, bending, removing of burrs and cleaning of pipes, passing of 14 gauge G.S. pull wires through the pipes, blocking open ends with metal caps, fixing identification number tags including all welding etc as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 50 mm dia

M-4 Supplying, laying, jointing, fixing and embedding in all types of foundations and super structures Class B (Medium duty) galvanised steel pipes of approved quality conforming to IS:1239/IS:1978 of following diameters with necessary sockets, check nuts, jumpers etc for electrical conduit pipes including threading, bending, removing of burrs and cleaning of pipes, passing of 14 gauge G.S. pull wires through the pipes, blocking open ends with metal caps, fixing identification number tags including all welding etc as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) 65 mm dia

M-4 Supplying, laying, jointing, fixing and embedding in all types of foundations and super structures Class B (Medium duty) galvanised steel pipes of approved quality conforming to IS:1239/IS:1978 of following diameters with necessary sockets, check nuts, jumpers etc for electrical conduit pipes including threading, bending, removing of burrs and cleaning of pipes, passing of 14 gauge G.S. pull wires through the pipes, blocking open ends with metal caps, fixing identification number tags including all welding etc as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: c) 80 mm dia

M-4 Supplying, laying, jointing, fixing and embedding in all types of foundations and super structures Class B (Medium duty) galvanised steel pipes of approved quality conforming to IS:1239/IS:1978 of following diameters with necessary sockets, check nuts, jumpers etc for electrical conduit pipes including threading, bending, removing of burrs and cleaning of pipes, passing of 14 gauge G.S. pull wires through the pipes, blocking open ends with metal caps, fixing identification number tags including all welding etc as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: d) 100 mm dia

M-4 Supplying, laying, jointing, fixing and embedding in all types of foundations and super structures Class B (Medium duty) galvanised steel pipes of approved quality conforming to IS:1239/IS:1978 of following diameters with necessary sockets, check nuts, jumpers etc for electrical conduit pipes including threading, bending, removing of burrs and cleaning of pipes, passing of 14 gauge G.S. pull wires through the pipes, blocking open ends with metal caps, fixing identification number tags including all welding etc as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: e) 150 mm dia

M-4 Supplying, laying, jointing, fixing and embedding in all types of foundations and super structures Class B (Medium duty) galvanised steel pipes of approved quality conforming to IS:1239/IS:1978 of following diameters with necessary sockets, check nuts, jumpers etc for electrical conduit pipes including threading, bending, removing of burrs and cleaning of pipes, passing of 14 gauge G.S. pull wires through the pipes, blocking open ends with metal caps, fixing identification number tags including all welding etc as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: f) 200 mm dia

M-4 Supplying, laying, jointing, fixing and embedding in all types of foundations and super structures Class B (Medium duty) galvanised steel pipes of approved quality conforming to IS:1239/IS:1978 of following diameters with necessary sockets, check nuts, jumpers etc for electrical conduit pipes including threading, bending, removing of burrs and cleaning of pipes, passing of 14 gauge G.S. pull wires through the pipes, blocking open ends with metal caps, fixing identification number tags including all welding etc as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: g) 250 mm dia

M-5 Supplying, laying, jointing and fixing in position of approved P.V.C. conduit pipes of the following diameters in foundations and super structures including bending, cutting, jointing with special resin, providing 14 gauge G.S pull wire through the pipes, fixing identification number tags etc as per specifications and directions of Engineer/Consultant, all materials, tools, plant and labour complete in all respect: Class of pipe is class 2 or class 4 a) upto 25 mm dia (nominal)

M-5 Supplying, laying, jointing and fixing in position of approved P.V.C. conduit pipes of the following diameters in foundations and super structures including bending, cutting, jointing with special resin, providing 14 gauge G.S pull wire through the pipes, fixing identification number tags etc as per specifications and directions of Engineer/Consultant, all materials, tools, plant and labour complete in all respect: Class of pipe is class 2 or class 4 b) above 25 mm and upto 50 mm dia (nominal)

M-5 Supplying, laying, jointing and fixing in position of approved P.V.C. conduit pipes of the following diameters in foundations and super structures including bending, cutting, jointing with special resin, providing 14 gauge G.S pull wire through the pipes, fixing identification number tags etc as per specifications and directions of Engineer/Consultant, all materials, tools, plant and labour complete in all respect: Class of pipe is class 2 or class 4 c) above 50 mm dia and upto 80 mm dia (nominal)

M-5 Supplying, laying, jointing and fixing in position of approved P.V.C. conduit pipes of the following diameters in foundations and super structures including bending, cutting, jointing with special resin, providing 14 gauge G.S pull wire through the pipes, fixing identification number tags etc as per specifications and directions of Engineer/Consultant, all materials, tools, plant and labour complete in all respect: Class of pipe is class 2 or class 4 d) 100 mm dia (nominal)

M-5 Supplying, laying, jointing and fixing in position of approved P.V.C. conduit pipes of the following diameters in foundations and super structures including bending, cutting, jointing with special resin, providing 14 gauge G.S pull wire through the pipes, fixing identification number tags etc as per specifications and directions of Engineer/Consultant, all materials, tools, plant and labour complete in all respect: Class of pipe is class 2 or class 4 e) 150 mm dia (nominal)

M-5 Supplying, laying, jointing and fixing in position of approved P.V.C. conduit pipes of the following diameters in foundations and super structures including bending, cutting, jointing with special resin, providing 14 gauge G.S pull wire through the pipes, fixing identification number tags etc as per specifications and directions of Engineer/Consultant, all materials, tools, plant and labour complete in all respect: Class of pipe is class 2 or class 4 f) 200 mm dia (nominal)

M-6 Supplying and laying approved quality building paper as directed by the Engineer/Consultant, all materials and labour complete in all respect.

M-7 Supplying and fixing approved pre-moulded bitumen impregnated fibre board (Shalitex board or approved equivalent) of following thickness at expansion joints, gaps etc at and at all heights and depths above and below finished ground level as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect: a) 25 mm thick

M-7 Supplying and fixing approved pre-moulded bitumen impregnated fibre board (Shalitex board or approved equivalent) of following thickness at expansion joints, gaps etc at and at all heights and depths above and below finished ground level as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect: b) 40 mm thick

M-8 Supplying and laying 25 mm deep approved bitumen sealing compound in expansion joints of following widths in required proportion 80 kg of hot bitumen and 0.25 cu m of coarse sand complete in all respect as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect: a) 25 mm thick

M-8 Supplying and laying 25 mm deep approved bitumen sealing compound in expansion joints of following widths in required proportion 80 kg of hot bitumen and 0.25 cu m of coarse sand complete in all respect as per specifications and directions of the Engineer/ Consultant, all materials, tools and labour complete in all respect: b) 40 mm thick

M-9 Supplying and laying, bending and fixing in position fan hooks made of 16 mm dia x 650 long M.S. Round to ceilings, including cutting holes in shuttering, if necessary, and providing painting the fan hooks with two coats of ready mix synthetic enamel paint of make, colour and shade approved by the Engineer/ Consultant over two coats of approved primer conforming to IS:2074, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect.

M-10 Supplying, fabricating, transporting and fixing in position, M.S. grills consisting of 25 mm x 6 mm M.S. flats of design, pattern and sizes including necessary welding, grinding and drilling of holes to the frames for fixing etc and including providing complete painting with two coats of synthetic enamel paint (15 microns each coat) of make, colour and shade as approved by the Engineer/Consultant over two coats of primer (15 microns each coat) conforming to IS:2074 all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

M-11 Supplying and filling in trenches etc brickbats of following grades laid in layers in dry and loose conditions at all depths below finished ground level all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) with 50 mm and down graded brickbats

M-11 Supplying and filling in trenches etc brickbats of following grades laid in layers in dry and loose conditions at all depths below finished ground level all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) with 100 mm and down graded brickbats

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): a) NP2 class i) 150 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): a) NP2 class ii) 250 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): a) NP2 class iii) 300 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): b) NP3 class i) 350 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): b) NP3 class ii) 400 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): b) NP3 class iii) 450 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): b) NP3 class iv) 500 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): b) NP3 class v) 600 mm dia

M-12 Supplying, fitting and laying in position to correct level and slope R.C. pipes of following dia conforming to IS:458 including collars with joints packed with jute breading dipped in hot bitumen and filled with cement mortar (1:2) and curing, neatly finished with with 45 degree splay, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (Excavation and backfilling required for laying RC pipes will be measured and paid separately under relevant items): b) NP3 class vi) 900 mm dia

M-13 Supplying and fixing in position approved water stop in expansion/contraction joints and approved construction joints of RCC structures at and at all heights and depths above and below finished ground level, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 225 mm wide 6 mm thk, dumb bell shape, PVC water stop with centre bulb of approved make.

M-14 Supplying, fitting and fixing in position at all levels M.S pipes (medium duty) conforming to IS:1161 of following diameters for tubular hand railing in walkways, platforms, staircases, roofs etc, with two coats of synthetic enamel paint (25 microns each coat) of colour and shade as approved by the Engineer/ Consultant over two coats of primer (15 microns each coat) conforming to IS:2074, all as per attached specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect (Each running metre of pipe length will be measured for the purpose of payment). a) 40 NB

M-15 Supplying and filling 40 mm down graded stone metal/gravel in pits, trenches, outdoor yards etc at all positions, all as per specifications and directions of the Engineer/ Consultant all materials, tools, plant and labour complete in all respect.

M-16 Supplying and fixing of Sun control film of reflective type of approved manufacturer on glass panes of various sizes, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect (measurement shall be based on actual area covered by Sun control film)

M-17 Supplying and fixing hard wood frame of approved quality for window model air conditioner (approximate size 950 x 750 mm with 100 mm x 75 mm wooden section) including providing 2 Nos. M.S hold fasts of length 150 mm made of 25 x 5 mm flat fixed to frame by screws including cutting holes on masonry/ concrete and grouting the hold fast and frame in concrete of grade M15 in true line and level and painting the frame with two coats of wood primer and two coats of approved synthetic enamel paint, all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect

M-18 Supplying, fixing and fitting anodised aluminium/extruded aluminium strip 3 mm thick of approved make on masonry or concrete wall/floor/ceiling for expansion joint with aluminium screw 50 mm long on one side at 150 mm c/c with other end free to move complete in all respect and directions of Engineer/Consultant, all materials, tools, plant and labour complete in all respect

M-19 Supplying and fixing in position galvanised steel strips for earthing as directed by the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: a) 32 mm x 3 mm

M-19 Supplying and fixing in position galvanised steel strips for earthing as directed by the Engineer/Consultant, all materials, tools, plant and labour complete in all respect: b) 40 mm x 6 mm

M-20 Supplying, fitting and fixing in position stair case balustrade at all heights above ground level consisting of 12 mm x 12 mm M.S. square bars spaced at about 250 mm c/c welded to 100 mm X 100 mm X 8 mm thick M.S. plate inserts fixed to side face of concrete with 25 mm x 8 mm thick continuous M.S. flat welded at top welded to each balustrade, 50 mm x 100 mm kiln seasoned chemically treated 70mm x 35mm hardwood continuous hand rail at top of M.S. flat including providing French polish to all exposed hard wood surfaces and painting the steelwork with two coats of primer (15 microns each coat) and two coats of approved synthetic enamel paint (25 microns each coat), all as per directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

M-21 Supplying, fitting and fixing in position staircase balustrade at all heights above ground level consisting of 20 mm x 20 mm MS square bars spaced about 250 mm c/c welded to 75 x 30 x 8 thick M.S. plate insert fixed to side face of concrete with 25 mm x 8 mm thick continuous MS flat welded at top of each balustrade, 80 mm x 40 mm approved PVC handrest at top of MS flat including painting the steelwork with two coats of primer (15 microns each coat) and two coats of approved synthetic enamel paint (25 microns each coat) all as per directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

M-22 Supplying, fabricating and fixing in position M.S. tubular gates made of M.S. tubes, flats, angles, weld mesh etc including supplying and applying one coat of approved primer and two coats of synthetic enamel paint complete in all respect all as per directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

M-23 Supplying, decoiling, stretching fully and fixing to M.S./R.C fencing posts of approved quality 75 mm square (mesh size) chain link fencing of 4 mm nominal dia galvanised steel wire conforming to IS:2721 including supplying and fixing galvanised steel clips, bolts, nuts, washers etc for fixing with fencing posts, all as per and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect

M-24 Supplying and laying in position approved quality heavy duty cast iron grating over storm water drain, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

M-25 Providing pre-construction anti-termite treatment to soils, masonry and concrete foundations, back filled earth inside and outside building and under floors and foundations etc at all levels conforming to IS:6313 (Part 2) as per specifications using "Chloropyrifos - 20 EC" conforming to IS:6313 all materials and labour complete in all respect (Plinth area will be measured and paid for. The treatment shall be guaranteed for a period of 10 years against infestation)

M-26 Supplying and filling in percolation pits brickbats of following grades laid in layers in dry and loose conditions at all depths below finished ground level all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect a) with 25 mm and down graded brickbats

M-26 Supplying and filling in percolation pits brickbats of following grades laid in layers in dry and loose conditions at all depths below finished ground level all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect b) with 50 mm and down graded brickbats

M-26 Supplying and filling in percolation pits brickbats of following grades laid in layers in dry and loose conditions at all depths below finished ground level all as per specifications and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect c) with 125 mm and down graded brickbats

M-27 Supplying and fixing chicken wire mesh at the junction of concrete, brickwall and screed concrete, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

M-28 Supplying, decoiling, stretching fully and fixing to M.S./R.C fencing posts approved galvanised steel barbed wire of 2-ply, 12 gauge wire with 4 point thick set barbs at 75 mm centres including wire clip for fixing bolts, nuts, washers etc for fixing at corner posts all as per and directions of the Engineer/ Consultant, all materials, tools, plant and labour complete in all respect (each barbed to be measured separately; MS/RC posts will be measured and paid separately under relevant BOQ items).

M-29 Supplying, fitting and fixing in position at all heights CI rain water pipes with specials including all fittings, clamps as specified, all materials and labour complete in all respect a) 100 mm dia

M-29 Supplying, fitting and fixing in position at all heights CI rain water pipes with specials including all fittings, clamps as specified, all materials and labour complete in all respect b) 150 mm dia

M-30 Supplying, fitting & fixing mosquito net at the mouth of vent pipes 50-100 mm diameter as per specification and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect.

M-31 Supplying and filling sand in trenches, at all positions, all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

M-32 Supplying, fitting and fixing in position at all levels 50 dia stainless steel of approved quality tubular handrailing in walkways, platforms, staircases, roofs etc, as as per all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respects.

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. i) Double sleeve wedge expansion fastener of approved type. a) M10

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. i) Double sleeve wedge expansion fastener of approved type. b) M12

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. i) Double sleeve wedge expansion fastener of approved type. c) M16

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. i) Double sleeve wedge expansion fastener of approved type. d) M20

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. ii) Double sleeve wedge anchor bolts of approved type a) M10

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. ii) Double sleeve wedge anchor bolts of approved type b) M12

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. ii) Double sleeve wedge anchor bolts of approved type c) M16

M-33 Supplying, filling and fixing concrete expansion fastners/anchor bolts from approved manufacturer (viz.Hilti, Fischer etc.) in the RCC, walls, floor etc. including drilling holes in RCC/PCC using template, blowing out dust from drilled hole, fixing anchor. Note: Expansion fastner/anchor bolts supplied must be accompanied by manufacturer's test certificate including holding capacity (pull) and safe torque for each fastener. ii) Double sleeve wedge anchor bolts of approved type d) M20

M-34 Supplying and fixing 50 mm thick expanded polystyrene board or approved quality heat resistant material of density 15 kg/cu m on RC ceiling surfaces in size of 500 mm x 500 mm or as indicated in the drawing as an underdeck thermal insulation fixed with two coats of approved quality hot bitumen @ 2 kg/sq m over a priming coat of emulsion as per manufacturer's specification applied on ceiling surfaces, supported by chicken wire mesh netting tide with free ends of lacing wire with GI washers made of 22 gauge GI sheets at the end to hold the chicken wire mesh with the polystyrene board at its joints and the lacings are fixed with RC ceiling by coach screws, rawl plugs and round GI washers made of 22 gauge GI sheets. The GI washers to be provided with lacing wires at all level above plinth level under supervision of Engineer/ Consultant, all as per drawings, specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

M-35 Supplying and fastening of reinforcement bars/threaded rods in RCC duly pickled and flushed, including drilling holes in RCC using template if required, blowing out dust from drilled hole, positioning of bar/rod and fixing/setting with resin hardener chemical (lokset of FOSROC or equivalent) as per manufacturer's specification and direction of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect. a) 12 dia bars/rods

M-35 Supplying and fastening of reinforcement bars/threaded rods in RCC duly pickled and flushed, including drilling holes in RCC using template if required, blowing out dust from drilled hole, positioning of bar/rod and fixing/setting with resin hardener chemical (lokset of FOSROC or equivalent) as per manufacturer's specification and direction of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect. b) 16 dia bars/rods

M-35 Supplying and fastening of reinforcement bars/threaded rods in RCC duly pickled and flushed, including drilling holes in RCC using template if required, blowing out dust from drilled hole, positioning of bar/rod and fixing/setting with resin hardener chemical (lokset of FOSROC or equivalent) as per manufacturer's specification and direction of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect. c) 20 dia bars/rods

M-35 Supplying and fastening of reinforcement bars/threaded rods in RCC duly pickled and flushed, including drilling holes in RCC using template if required, blowing out dust from drilled hole, positioning of bar/rod and fixing/setting with resin hardener chemical (lokset of FOSROC or equivalent) as per manufacturer's specification and direction of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect. d) 25 dia bars/rods

M-36 Supplying and application of "SIKADUR 32 (LP) of sika"/DP bonding agent of SWC or other approved equivalent on roughened and cleaned old concrete surface prior to pouring of new concrete within specified time and at all depths above and below finished

M-37 Supplying, cutting, placing and fixing in position high density polyethylene (HDPE) down pipes conforming to IS:4984 to be used for sewer lines at and at all heights and depths above and below finished ground level with joints sealed with white zinc and hemp yarn including all HDPE fittings, such as heads, bends, offsets, swan necks, shoes, bobbins, sockets, M.S. clamps, wooden plugs, nails etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: Class of pipes are PE63, PE80 and PE 100. a) 100 mm dia

M-37 Supplying, cutting, placing and fixing in position high density polyethylene (HDPE) down pipes conforming to IS:4984 to be used for sewer lines at and at all heights and depths above and below finished ground level with joints sealed with white zinc and hemp yarn including all HDPE fittings, such as heads, bends, offsets, swan necks, shoes, bobbins, sockets, M.S. clamps, wooden plugs, nails etc, all as per specifications and directions of the Engineer/Consultant, all materials, tools and labour complete in all respect: Class of pipes are PE63, PE80 and PE 100. b) 150 mm dia

DISMANTLING AND TEMPORARY WORK

N-1 Removal of all vegetation, shrubs, bushes etc complete as directed by Engineer/Consultant and disposing the same anywhere as directed by Engineer/Consultant, all tools and labour complete in all respect.

N-2 Uprooting trees carefully having a girth measured at a height upto 1.0 m above ground level or as directed by Engineer/ Consultant transporting the trees in convenient sizes anywhere within Purchaser works premises and stacking them, all tools and labour complete in all respect. a) girth size upto 250 mm

N-2 Uprooting trees carefully having a girth measured at a height upto 1.0 m above ground level or as directed by Engineer/ Consultant transporting the trees in convenient sizes anywhere within Purchaser works premises and stacking them, all tools and labour complete in all respect. b) girth size from 251 mm to 500 mm

N-3 Uprooting carefully trees including roots having a girth measured at a height upto 1.0 m above ground level or as directed by the Engineer/ Consultant, transporting anywhere within Purchaser Works premises and replanting the uprooted trees at allotted areas as directed by Engineer/ Consultant, including preparing the ground by necessary digging & filling at the area of re-plantation, complete in all respect: a) upto 250 mm

N-4 Dismantling with due care of brick masonry work at all heights and depths above and below finished ground level and disposing of the muck/debris within a lead of 500 m as directed by the Engineer/Consultant

N-5 Dismantling with due care of plain/ reinforced cement concrete work at all heights and depths above and below ground level using pneumatic equipment and disposing of muck/ debris within a lead of 500 m as directed by the Engineer/Consultant. a) work including cutting of reinforcement rods and embedments

N-5 Dismantling with due care of plain/ reinforced cement concrete work at all heights and depths above and below ground level using pneumatic equipment and disposing of muck/ debris within a lead of 500 m as directed by the Engineer/Consultant. b) work including exposing the reinforcement rods, straightening and cleaning the same

N-6 Dismantling of road/pavement work including removal of muck/debris upto a lead of 500 m as directed by the Engineer/Consultant a) Bituminous road/pavement

N-6 Dismantling of road/pavement work including removal of muck/debris upto a lead of 500 m as directed by the Engineer/Consultant b) Concrete road/pavement

N-7 Dismantling with due care RR masonry work at all heights and depths above and below finished ground level and disposing of the muck/debris within a lead of 500 m as directed by the Engineer/Consultant all materials, tools, plant and labour complete in all respect.

N-8 Extra over item N-4, N-5 and N-6 for disposal . Note: The quantity for payment shall be arrived by multiplying the transported quantity with the actual distance of haulage beyond initial lead of 1000m. a) for lead beyond initial lead of 1000m ( The rate provided is for haulage of one cum quantity for one km distance)

ROADWORK

P-1 Earthwork in excavation for box-cutting in all types of soil and filled materials but excluding hard rock in mass which requires Breaking for forming road base to required sub-levels and cross-sections and dressing the bottom of excavation, in both dry and wet conditions, including stripping of the existing vegetation cover and necessary pumping/bailing out of water, slush removal etc and transporting the excavated material to spoil dumps/fill areas/excavated pits/ road berms within a lead upto 1 km including levelling of the disposed excavated materials all as directed, as per specification and direction of the Engineer, all tools, plant and labour complete. Note: Excavation will be measured paid as per the approved excavation plan or as per actuals whichever is less. The Tenderer may be asked to excavate and transport the earth directly for mass backfilling in other areas within a lead of 1 km. In such cases, no extra payment for backfilling shall be made. a) upto 1.5 m depth below existing ground level

P-2 Watering, rolling and compacting the bottom of excavation with minimum six (6) passes of 80 - 100 KN power roller for formation of road sub-grade to achieve a CBR value as specified in the drawing and density of not less than 98% of the maximum dry density of the soil as obtained by Standard Proctor Test and dressing to correct camber, profile and slope all as per specification and direction of the Engineer, all materials tools, plant, and labour complete

P-3 Supplying and laying of granular lower sub-base with the mixture of 60% gravel (grading-1 of Table-1 of specification) of approved quality and 40% granulated blast furnace slag (GBFS) by weight with maximum compacted thickness of 225 mm in each layer, with CBR value not less than 30% of the mix including spreading the materials on prepared subgrade, mixing by mechanical means, dressing, watering and rolling with optimum moisture content (OMC) using 80 to 100 kN vibratory roller and compacted to at least 100% of maximum dry density obtained by laboratory tests as per IS:2720 (Part-8), including transporting, unloading, stacking etc., necessary testing of materials and finishing the work, all complete in all respect as per specifications and/or as directed by the Engineer/Consultant, (payment based on finished volume of the granular lower sub-base)

P-4 Supplying and laying of granular lower sub-base with the mixture of 60% gravel (grading-1 of Table-1 of specification) of approved quality and 40% granulated blast furnace slag (GBFS) by weight with maximum compacted thickness of 225 mm in each layer, with CBR value not less than 30% of the mix including spreading the materials on prepared subgrade, mixing by mechanical means, dressing, watering and rolling with optimum moisture content (OMC) using 80 to 100 kN vibratory roller and compacted to atleast 100% of maximum dry density obtained by laboratory tests as per IS:2720 (Part-8), including transporting GBFS as marked separate.

P-6 Supplying, laying, compacting cast-in-situ PCC kerb stone using kerb casting and laying machine, top and bottom width 150 mm in concrete of grade M-25 as defined by IS:456 with 20 mm and down graded stone aggregates as per specification and direction of Engineer/Consultant including curing, providing shuttering, necessary excavation for laying the kerb stones, backfilling and removal of surplus excavated materials after removal of shuttering, disposal of the same to spoil dumps within a lead of 3 KM, all materials, tools, plant, labour complete in all respect.

P-7 Manufacturing, erecting and fixing in position with (1:4) cement sand mortar precast PCC kerb stones of the following sizes with concrete grade M25 as defined by IS:456, machine mixed and mechanically vibrated with 20 mm and down graded stone aggregates all as per specification and direction of the Engineer/Consultant including curing, providing shuttering, making excavation for fixing the kerb stones and removal of surplus excavated materials after completion and depositing in spoil dumps/fill areas within a lead of 3 km, all materials, tools, plant and labour complete in all respect: i) For straight portion a) 950 mm x 150 mm x 600 mm long

P-7 Manufacturing, erecting and fixing in position with (1:4) cement sand mortar precast PCC kerb stones of the following sizes with concrete grade M25 as defined by IS:456, machine mixed and mechanically vibrated with 20 mm and down graded stone aggregates all as per specification and direction of the Engineer/Consultant including curing, providing shuttering, making excavation for fixing the kerb stones and removal of surplus excavated materials after completion and depositing in spoil dumps/fill areas within a lead of 3 km, all materials, tools, plant and labour complete in all respect: ii) For curved portion b) 950 mm x 150 mm x 600 mm long

P-8 Providing and laying Granular upper sub-base with coarse graded granular material of grading-1 (53 mm to 4.75 mm) as per Table-2/3 of specification with CBR value not less than 30% of the mix including spreading in uniform layers of 150 mm thick with motor grader on prepared lower sub-base, mixing by mix in place method with rotavator at OMC and compacting with vibratory roller of 80-100 kN capacity to achieve the desired density of 98% of the maximum dry density for the materials determined as per IS:2720 (Part-8) complete in all respect as per specification for finished item of work as directed by the Engineer/Consultant

P-9 Providing and filling moorum of approved quality in layers, each layer not exceeding 100 mm thick, including consolidating each layer by watering and ramming at any location all as per specifications and directions of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

P-10 Supplying and laying Bituminous Macadam (BM) composed of crushed coarse & fine aggregates with bituminous binder over a layer of prime coat on base course compacted to correct slope, grade and finished thickness including compacting, rolling with 80-100 KN smooth wheeled roller, as per specification and directions of the Engineer/ Consultant all materials, tool plant and labour complete in all respect: a) 50 mm thick (finished thickness)

P-10 Supplying and laying Bituminous Macadam (BM) composed of crushed coarse & fine aggregates with bituminous binder over a layer of prime coat on base course compacted to correct slope, grade and finished thickness including compacting, rolling with 80-100 KN smooth wheeled roller, as per specification and directions of the Engineer/ Consultant all materials, tool plant and labour complete in all respect: b) 60 mm thick (finished thickness)

P-11 Supplying and laying Dense Graded Bituminous Macadam (DBM) of compacted crushed coarse and fine aggregates with bitumen binder complying with IS:73 to correct slope, grade and thickness including compacting, rolling with 80-100 KN smooth wheeled roller over a layer of prime coat as per specification and directions of the Engineer/Consultant all materials, tool plant and labour complete in all respect: a) 60 mm thick ( finished thickness)

P-12 Supplying, laying and compacting Bituminous Concrete (BC) in one layer composed of coarse, fine aggregates, filler and bitumen of penetration grade complying with IS:73 over a tack coat on bituminous base to correct slope, grade and finished thickness including compacting, rolling with smooth wheeled roller, as per specification and directions of the Engineer/Consultant all materials, tool plant and labour complete in all respect: a) 25 mm thick ( finished thickness)

P-12 Supplying, laying and compacting Bituminous Concrete (BC) in one layer composed of coarse, fine aggregates, filler and bitumen of penetration grade complying with IS:73 over a tack coat on bituminous base to correct slope, grade and finished thickness including compacting, rolling with smooth wheeled roller, as per specification and directions of the Engineer/Consultant all materials, tool plant and labour complete in all respect: b) 40 mm thick ( finished thickness)

P-13 Supplying, laying and compacting open-graded premix carpet in one layer composed of graded stone chips premixed with bituminous binder complying with IS:73 over a layer of tack coat on Bituminous base to correct slope, grade and finished thickness including compacting, rolling with 80-100KN smooth wheeled roller, as per specification and directions of the Engineer/Consultant all plant, tools, materials and labour complete in all respect a) 20 mm thick ( finished thickness)

P-13 Supplying, laying and compacting open-graded premix carpet in one layer composed of graded stone chips premixed with bituminous binder complying with IS:73 over a layer of tack coat on Bituminous base to correct slope, grade and finished thickness including compacting, rolling with 80-100KN smooth wheeled roller, as per specification and directions of the Engineer/Consultant all plant, tools, materials and labour complete in all respect b) 25 mm thick ( finished thickness)

P-14 Supplying and laying of premix seal coat comprising of approved quality sand @ 0.06 cu m per 10 sq m & 60/70 grade bituminous binder @ 6.8 kg/ 10 sq m both preheated to required temperature, thoroughly premixed, spread uniformly on bituminous surface to specific level, grade, and cross fall, all as per specification and direction of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect.

P-15 Providing speed-breaker hump as per with cement concrete of grade M20 with stone aggregate 20 mm and down nominal size, laid at road surface true to line, level and curvature, compacted with appropriate size needle vibrator and/or plate vibrator all as per specification and direction of the Engineer/Consultant, all materials, tools, plant and labour complete in all respect

P-16 Providing painted cautionary bands of required patterns on road/speed breaker/guard stones/ kerb surfaces, using floor enamel paint of required shades in three coats, including supply of paint all complete in all respect as per directed by the Engineer/Consultant (Payment based on plan area in case of speed breaker)

P-17 Painting lane markings on the road surface with two or more coats of ready mixed road marking white paint conforming to IS:164, including cleaning the surface of all dirt scales, oil, grease and foreign material etc., complete in all respect all as per the directions of the Engineer/Consultant

P-18 Supplying, fabricating and erecting in position 90 cm triangle shaped standard traffic signs, side road ahead and the like, with scotch lits reflective high intensity heat activated sheet bonded on standard 140 aluminium blank of suitable size, sign plates mounted on 3 M long 50 NB galvanised steel pipe conforming to IS:1239, with bolts & nuts, welded with 100 x 100 x 6 mm thick MS base plate and 6 mm, thick MS capping at top, complete in all respect pipe and rear of aluminium blank painted with one coat of zinc chromate yellow primer and two or more coats of enamel paint in approved pattern to match with the even shade, of approved brand, 450 x 450 x 600 mm foundation block of PCC M7.5, necessary earthwork excavation, backfilling, disposal of surplus earth upto a lead 500 m all complete in all respect as per IRC specifications and/or as directed by the Engineer/ Consultant.

STRUCTURAL STEEL WORKS

Supply of structural steel materials, loading, transporting, unloading, fabricating, erecting and fixing in position at all heights and depths above and below finished ground level welded /bolted structural steel work as specified for all members of building structures, such as all types of column bracings, all types of gantry girders, buffers, surge diaphragms, platforms, roof trusses, purlins, lacings, bracings, stiffeners, side and gable runners, beams, roof plates, MS louvers, brackets, monorails and its supports, lifting beams, posts and hangers, wind girders, floor & platform supports, stagings, staircases, toe guards, ladders, heat shields, walkways, pipe & cable racks, clamps, ties, struts, diaphragms, sag rods including threading, sag angles and all other miscellaneous structural steel work etc., as specified and as shown on drawings and / or as directed by the Engineer/Consultant including supplying and fixing bolts conforming to property class 4.6 (precision / semi precision type), nuts, washers, fittings, fixtures, etc., applying two coats of red oxide zinc chromate primer (15 microns each coat) and two coats of approved enamel paint (25 microns each coat).

Supplying, fabricating, fixing at all heights and depths above and below finished ground level M.S. tubular hand railing including posts for hand railing top and mid rails, (toe guards) etc for roofs, gantry girders, stair cases, platform, walkway, fencing etc and applying two coats of red oxide zinc chromate primer (15 microns each coat) and two coats of approved enamel paint (25 microns each coat) after fabrication as specified and as shown on drawings and/or as directed by the Engineer/ Consultant, all materials, tools, plant, labour etc complete in all respect.

Supply of structural steel materials, loading, transporting, unloading, fabricating, erecting and fixing in position as shown in the drawing, at all heights and depths above and below finished ground level square/ rectangular walkway/hot mesh gratings of opening size of about 50 mm x 30 mm as specified and as shown on drawings and/or as directed by the Engineer/ Consultant fabricated with steel sections such as flats, bars, angles and channels etc., all materials, tools, plant labour etc. complete in all respect.

Supply of structural steel materials, loading transporting, unloading, fabricating and erecting and fixing in position at all heights and depths above and below finished ground level, chequered plate excluding structural steelwork for supports and stiffeners, at floors, walkways, platforms, staircases, etc as specified and as shown in drawings and/or as directed by the Engineer/Consultant including supplying and fixing bolts conforming to property class 4.6 (precision/semi-precision type), nuts, washers etc, applying two coats of approved primer (15 microns each coat) after fabrication and two coats of approved enamel paint (25 microns each coat), all materials, tools, plant labour etc. complete in all respect

Supply of structural steel materials, loading, transporting, unloading, fabricating, erecting and fixing in position at all heights and depths above finished ground level welded /bolted structural steel work as specified for all members of building structures, such as all types of crane rails conforming to IS:3443 and fixtures for crane rail, as specified and as shown on drawings and / or as directed by the Engineer/ Consultant including supplying and fixing of clips/bolts, nuts, washers, fittings, fixtures, etc., applying two coats of red oxide zinc chromate primer (15 microns each coat) and two coats of approved enamel paint (25 microns each coat).

Supplying, fabricating, erecting and fixing in position as shown in the drawing, at all heights and depths above and below finished ground level welded mesh made of 4 mm dia MS rod including structural framework at roof openings, coverings as specified and as shown on drawings and/or as directed by the Engineers/Consultant including supplying and fixing bolts conforming to property class 4.6 (precision /semi precision type), nuts, washers, fittings, fixtures etc. applying two coats of approved primer (15 microns each coat) after fabrication and two coats of approved enamel paint (25 microns each coat), all materials, labour, tools and plant to complete the work in all respects.

Supply of 5/6 mm thick M.S. plates (conforming to IS:2062) loading, transporting, unloading, fabricating, erecting, fixing in position gutters, including all structural steel work for supports, bearers, clamps, stiffeners etc. at all heights and depths above and below finished ground level including supplying and fixing bolts conforming to property class 4.6 (precision/semi-precision type) nuts, washers etc, as specified and as shown on drawings and/or as directed by the Engineer/ Consultant applying two coats of approved primer (15 microns each coat) and two coats of approved enamel paint (25 microns each coat) after fabrication, all materials, labour, tools and plant to complete the work in all respect.

Conducting ultrasonic testing of plates for cracks, laminations, fissures etc complete as per specification, all tools, plants, materials and labour complete in all respect

Conducting radiographic testing (film size 9 inch x 3 inch) of butt welds complete as per specification, all materials, tools, plant and labour complete in all respect

Supplying, cutting, shaping and fixing sal wood make wooden blocks of approx. size 200 mm x 200 mm x 300 mm for crane rail buffers with through bolts, nuts and washers as shown on drawings, all materials, tools, plant and labour complete in all respect.

Supplying, transporting to site, cutting, placing and fixing in position at all heights above finished ground level pre-colour coated trapezoidal profile steel sheets minimum 0.5 mm total coated thickness (TCT) for roof & monitor including supply and fixing of self tapping, self drilling steel screws with integral EPDM washers etc of approved make, Aluminium pop rivet of approved make, non-hardening poly-sulphide or other approved sealant, mastic tapes and all other accessories to prevent water penetration, all ridging/flashing using the pre-colour coated plain sheets minimum 0.5 mm total coated thickness (TCT), all with metallic coating and paint coating on top and bottom surfaces as per the technical specification , Part B: Cl.E Type-II and conforming to the requirements and standards as specified and of approved make including on-site roll forming facilities to extrude single length trapezoidal profile sheet if required, suitable for direct erection on roof, all as per the direction of Engineer and as shown on drawings, all materials, tools, plant and labour complete. (Only net areas/length as laid excluding laps will be measured)

Supplying, transporting to site, cutting, placing and fixing in position at all heights above finished ground level pre-colour coated trapezoidal profile steel sheets minimum 0.5 mm total coated thickness (TCT) for side/gable including supply and fixing of self tapping, self drilling steel screws with integral EPDM washers etc of approved make, Aluminium pop rivet of approved make, non-hardening poly-sulphide or other approved sealant, mastic tapes and all accessories to prevent water penetration, all flashing ,using the pre-colour coated plain sheets minimum 0.5 mm total coated thickness (TCT), all with metallic coating and paint coating on top and bottom surfaces as per the technical specification, Part B: Cl.E Type-II and conforming to the requirements and standards as specified and of approved make, including on-site roll forming facilities to extrude single length trapezoidal profile sheet if required, suitable for direct erection on side/gable, all as per the direction of Engineer and as shown on drawings, all materials, tools, plant and labour complete. (Only net areas/length as laid excluding laps will be measured)

Supplying , transporting to site, cutting, placing and fixing in position at all heights above finished ground level Polycarbonate sheets 2 mm thick on roof / vertical faces matching with the Trapezoidal profile sheets including supplying and fixing of all necessary accessories and finally beading the joints with silicon sealant to prevent water penetration, all as per the technical specification all as per the direction of Engineer and as shown on drawings, all materials, tools, plant and labour complete. (Only net areas/length as laid excluding laps will be measured)

Supplying, fabricating, transporting, erecting and fixing in position at all heights and depths above and below finished ground level welded structural steelwork for in-situ modification/ strengthening of existing structural members like all types of columns, gantry girders, auxiliary and surge girders, diaphragms, platforms, roof trusses and girders, bracings, stiffeners, beams, brackets, monorails and it's supports, lifting beams, posts and hangers, wind girders, floor and platform supports, stagings, staircases, walkways, M.S. Angle/Tubular Sections/Posts in hand railings, mid rails, toe guards and all other miscellaneous structural steelwork as specified and as shown on drawings and/or as directed by the Engineer/ Consultant including supplying and fixing bolts conforming to property class 4.6 (precision/semi-precision type), nuts, washers, fittings, fixtures etc. including painting after necessary surface cleaning of existing structural members and touch up with two coats of red oxide zinc chromate primer (15 microns each coat) in the damaged portion and with all material, labour, tools and plant complete in all respect. Note: Newly Strengthened/added members will be taken for measurement

Supplying and providing grout with M30 grade concrete as defined by IS:456 with 6 mm and down graded stone aggregates in column bases after aligning and levelling of steel structures including cleaning column bases/foundation tops, providing shuttering, mixing, placing, ompacting and curing, all as per drawings and directions of the Consultant, all materials, tools, plant and labour complete in all respect.

Supplying, transporting to site, fabricating and fixing Galvanised link chains used for handrailing at all heights and depths above and below finished ground level made up of 6 mm dia. MS Rounds electrically welded. Outside length and width of links shall not exceed 6 times and 3½ times the diameter of the material respectively as shown on drawings and/or as directed by the Engineer/Consultant with all materials, tools, tackles, labour etc. complete in all respect.

Radiographic testing of welded joints

Ultrasonic testing of welded joints

Bidder Name

Amount in Words

Furnace Fabrica (India) Limited

D K Engineering & Construction

Gaja Engineering Private Limited

NTPC GE Power Services Private Limited

BRIDGE AND ROOF CO. INDIA LTD.

NTPC GE Power Services Private Limited

D K Engineering & Construction

Gaja Engineering Private Limited

Furnace Fabrica (India) Limited