PROVN OF STORE ROOM CUM MULTIPURPOSE ROOM IN DRZN OFFICE COMPLEX AND SPECIAL REPAIRS TO BLDG NO NP-02 AT HQ NC UNDER GE (SOUTH) UDHAMPUR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4 sqm each and removing complete all as specified and as directed.

Taking down cement plaster of any descreption on brick/stone walls or concrete surfaces including racking out joints, hacking for key scrubbing down with water etc on walls and ceiling, complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and as directed.

Dismantling structural steel work including doors, gates including framed truss etc complete all as specified and as directed.

Dismantling wall & ceiling boards of any description and thickness including cover fillets, complete all as specified and as directed.

Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

4mm thick Cement fibre board (designer ceiling) of size 600mm x 600mm panel conforming to IS 14862 type B category three including GI frame work with size of grid 605mm x 605mm including all accessories and GI suspensions, the fibre sheet should be fire resistant, water resistant, termite resistant, environment friendly & 100% asbestos free complete all as specified and as directed.

Non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Glazed Coloured Ceramic tiles in vertical surface 300x450x7mm or 300x600x7mm thick laid over 10 mm thick rendering/backig coat in CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

Dura stone heavy duty vitrified tiles of size 300 x 300mm x 8-10mm thick as in floors set and jointed in neat cement slurry and pointed in white cement to match the surface including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Make : Ecocell or equivalent make

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Make : Ecocell or equivalent make

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type wire mesh solid door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Make : Ecocell or equivalent make

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Make : Ecocell or equivalent make

Powder coated (50 micron of approved colour) Aluminum anodised double shutter window (glazed and wire gauge) side hung with aliminium window frame or chowkat 1.50 mm thick sheet & section aluminium anodised of size 100 mm x 44.50 mm and window shutter frames made of (middle, top rail, bottom) and styles 1.5 mm thick aluminium anodised sheet & section of size 44.5 x 44.5 mm including aluminium grill and all fittings such as rubber gasket aluminum glazing clips locking cabinet and 75 mm handle and including 4 mm thick tinted glass pane in panes glazed shutter fixed with rubber gasket and glazing clip/aluminium beads and with stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples on gauge shutter including aluminium tower bolt 75mm 02 Nos in each shutter, aluminium hinges 100mm B-12) 02 Nos in each shutter, aluminium handle 100 mm 01 No in each shutter including all accessories complete all as specified and as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of apertue 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

250mm long aluminium alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloys to door shutter in ISI marked complete all as specified and as directed.

150mm long aluminium, anodized, barrel tower bolts of extruded section complete all as specified and as directed.

Butt hinge 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed.

150mm aluminium handles, cast type, anodised complete all as specified and as directed.

150mm double action spring hinges, mild steel with steel wire spring, stove enamelled, black complete all as specified and as directed.

100mm hasp and staple aluminium anodized including bolts two hinge plate and fixed with screws complete all as specified and as directed.

Granite stone 18-20mm thick (table rubbed and polished) in window cills, cooking platforms and the like not less than 1 Sqm (in one piece), laid over 15mm thick layer of cement mortar 1:3 after roughening of existing concrete surface and applying a layer of neat cement slurry @ 3Kg/Sqm including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone, including demolition of stone slabs and tiles of any description or thickness in floors etc. laid, bedded and pointed in any mortar complete all as specified and as directed.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and as directed.

Rolled mild steel Fe-410w (Gde-E-250) quality 'B' Roof trusses (framed ), trussed, purlins, crane gantries , rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and as directed.

4 mm dia galvanised steel wire 150 mm x 100 mm mesh made up in to matresses or cages etc complete all as specified and as directed.

Anodised aluminium window and ventilator shutters, side hung type without sash bar aluminium section weighing 0.55 kg/m including necessary joining cleat , glazing clips, rubber packing, frosted glass 4mm thick, anodised aluminium snap beading screws , anodised aluminium fitting such as peg stays 150mm long (1 no) hinges type B-12 100mm long (2 no ) suitable handle (1 no) etc complete all as specified and as directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 15mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately) and applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) complete all as specified and as directed.

Water proofing treatment to surfaces of walls/concrete slabs damaged due to moisture and efflorescence including sunken areas of bathrooms/toilets, in balconies by applying acrylic polymer modified cementitious high performance coating or treatment all as per manufacturer's instructions, complete all as specified and as directed.

Brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:6 including demolition of old brick/stone masonry complete all as specified and as directed.

PCC 1:2:4 Type B-1 using 20 mm graded crushed stone aggregate in surface channels and drains complete all as specified and as directed.

Cement concrete 1:2:4 type B1 (using 20 mm gradded crushed stone aggregate) use in coping, hold fast and similar work including naccesary form work complete all as specified and as directed.

Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:4) including finishing the surfaces fair and even without using extra cement complete all as specified and as directed.

Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:6) including finishing the surfaces fair and even without using extra cement complete all as specified and as directed.

Rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces as on ceiling complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified.

75 mm thick PCC 1:4:8, type D-2 by using 40 mm graded crushed stone aggregate as in sub base floor complete all as specified and as directed.

25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes complete all as specified and as directed.

Machine cut Kota stone slab flooring 18-20mm thick over cement screed base 15 mm thick in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

S&F in repair curtain/Harrison rails of stainless steel 20mm dia, chromium plated with fixing brackets, stops, end bulbs, rollers etc complete all as specified and as directed.

S & F in repair 15mm bore bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S & F in repair 15mm bore stop valve/angle cock, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S&F in repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repair Soap dish holder incl all fittings complete all as specified and as directed.

S & F in repair 125mm chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

S&F in repair countertype vitreous chinaware wash hand basin (WHB) white size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete all as specified and as directed.

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S & F in repair Vitreous china squatting pan 'Orissa' pattern size 580x440 mm white with integral foot rest including connection to trap and flushing pipe complete all as specified and as directed.

S&F in repairs 10 litres capacity PVC low level flushing cistern white inlet float valve, handle complete including brackets complete all as specified and as directed.

PVC connection 15 mm dia and 600mm long with two Nos of brass check nuts and washers complete all as specified and as directed.

Vitreous china urinal half stall type white incl waste pipe fixed in repairs complete all as specified and directed.

S&F in repair concussive push button taps of cast copper alloy, screwed for iron pipe and fixed complete all as specified and as directed.

15mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

20mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

25mm bore steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 15mm bore including taking down old pipe complete all as specified and as directed.

1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and PTMT ball valve 20mm dia including taking down of old tank and removing from site complete all as specified and as directed.

S & F in repair of gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends for iron pipe of size 20mm bore complete all as specified and as directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed.

110 mm PVC (SWR) bends any redius with access door complete all as specified and as directed.

110 mm PVC (SWR) branch piece, (singal T) equal or unequal with access door complete all as specified and as directed.

PVC (SWR) Floor trap, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good complete all as specified and as directed.

RCC 1:2:4 type B1 using 12.5mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Flat formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed.

Mild Steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS complete all as specified and as directed.

600 mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embeded in cement mortor 1:3 with MS screws complete all as specified and as directed.

Preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Applying 1 mm thick layer of wall putty on walls to give uniform surface, surface scrubed with emery paper and make surface good and clean complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

Preparation of new plaster surfaces of walls/ceiling and applying two coats of oil emulsion distemper (white/tinted) complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil etc complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation complete all as specified and as directed.

RCC M-25 (20mm graded aggregate crushed stone aggregates) as in foundations footings, plinth beams etc complete all as specified and as directed.

RCC M-25 (20mm graded aggregate crushed stone aggregates) as in columns, pillars etc complete all as specified and as directed.

RCC M-25 (20mm graded aggregate crushed stone aggregates) as in beams, lintels etc complete all as specified and as directed.

RCC M-25 (20mm graded aggregate crushed stone aggregates) as in chajjas etc complete all as specified and as directed.

RCC M-25 (20mm graded aggregate) as in slab type Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Mild Steel TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

Form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (horizontal or sloping) complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintes,cantilevers, shelves including supports, overhangs, etc also splays beteen floors and beams finished rough surfaces of concrete complete all as specified and as directed.

Formwork to chajjas, chullah hoods, similar items including edges complete all as specified and as directed.

Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and as directed.

Half brick wall with sub class B bricks, straight or curved on plan exc 6 m mean radium built in CM 1:4 complete all as specified and as directed.

Hardcore of broken stone or boulders of gauge exc. 63mm but n exc 100mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface complete all as specified and as directed.

Double charged glossy finished Vitrified tiles light Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Double charged glossy finished Vitrified tiles light Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, in vertical surface as in skirting/dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed in CM 1:4 complete all as specified and as directed.

75mm thick PCC 1:3:6 type C-2 as plinth protection, finished even and fair without using extra cement complete all as specified and as directed.

18-20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab complete all as specified and as directed.

Powder coated 15 micron aluminium door of approved design complete all as specified/directed with all fixing arrangement including providing and fixing door handle, tower bolts, mortice lock 6 lever (Make - Harrison/Godrej) one on each door and , aluminium Powder coated tower bolts 200 mm long (03 Nos on each shutters) and 5 mm thick tinted glass pane of glazed shutter along with aluminium glazing beading of size 19.00 mm x 17.5 mm x 0.70 mm @ weight of 0.097 Kgs per RM including rubber gasket on both side complete alongwith neoprene lining. The member shall be made out of extended aluminium section comprising of :- (Size of the door shall be as per site requirement) (a) Door frame of size 95.25 mm x 44.50 mm x 1.70 mm @ 1.301 Kg/RM.. (b) Shutter vertical member 85 x 44.50 x 1.56 mm @ 1.39 Kg per RM. (c) Shutter top member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. (d) Shutter bottom member 101.60 x 44.50 x 1.60 mm @ 1.301 Kg per RM. (e) Shutter lock rail member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM.

Aluminium powder coated frame with window shutters (glazed, wire gauge and grill) side hung or three track with aluminium window frame or chowkat 1.5 mm thick aluminium powder coated of size 100 mm x 44.5 mm and window shutter frames glazed and wire gauze (middle, top rail, bottom rail) and styles 1.5 mm thick aluminum powder coated of size 44.5x44.5 mm incl powder coated aluminium grill 50mm x 50mm aparture and all fitting such as rubber gasket, aluminium glazing clips locking cabinet, 4 mm thick tinted glass pane for glazed shutters, stainless steel wire mesh for gauge shutter and hook and eye for each shutter fixed with rubber gasket and glazing clip/aluiminium beads aluminium tower bolt 75 mm 02 Nos each shutter, aluminium butt hinges 75 mm 02 Nos in each shutter aluminium handle 100 mm 01 No in each shutter inc all accessories complete all as specified and as directed.

Rendering 10mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces & finishing the surface fair and even without using extra cement complete all as specified and as directed.

Material and labour for APP polymaric water proofing membrene minimum 3mm thick and weighting not less than 3.6 kg / sqm of make 'Moply FP' manufactured by STP Texsa Ltd or' Hyper Plas' ( polyster) manufactured by M/S IWL Ltd or'Shaliplas' (polyster) manufactured by M/S Capital Steels and chemicals Pvt Ltd or 'Mak polyplast' manufactured by M/S M K Petro as approved by GE , black finished reinforced with non weven polyster matt,with fusable finish laid over compatable bitumen primer at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or abutane gas torch, with a over lap of 75mm at the sides and100 at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufactur's instructions including 0.40 Ltr/Sqm torching overlaps with a propane or abutane gas torch, with a over lap of 75mm at the sides and100 at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufactur's instructions including preparation of surface, complete all as specified and as directed. Note : the water proofing treatment shall be carried out by the manufacturer or their authorised applicators.

M&L for two or more coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power/ LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and as directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly complete all as specified and as directed. Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish.

All as per srl item No 106 but for 3 pin 6 Amps socket outlet independent board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 106 but for 3 pin 6 Amps socket outlet on the same board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 106 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

All as per srl item No 106 but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly.

All as per Srl item No 106 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and as directed.

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and as directed.

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge. Make: Havells/ Legrand/Indoasian Elvira

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and as directed.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block complete all as specified and as directed.

S&F in replacement single pole and neutral enclosure surface mounted 240 voltswith 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of complete all as specified and as directed.

Supply and fixing in replacement LED lights fitting 1x 20W, 230V,AC decorative box type warm white colour with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F in replacement 36W (2 x 2) LED Ceiling/recess light panel for recess mounting warm white colour which provides soft-light and glare free symmetrical illumination complete all as specified and as directed.

S&F in replacement Sheet metal enclosure double door type for MCCB TPN DB upto 125 Amps, 4 way vertical type 415 volts with 400 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S & F replacement MCCB Three Pole & Neutral capacity of 125 amps 415 volts rupturing capacity 16 KA complete all as specified and as directed.

S&F in replacement Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 08 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S&F Sheet metal enclosure double door type for DBs (when MCB to be used) 12 way 240 volts with 200 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S&F Sheet metal enclosure double door type for DBs (when MCB to be used) 4 way 240 volts with 200 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specificationcomplete all as specified and as directed.

S & F in replacement MCB single pole 240 volt any rating from 10 to 40 amps "C" series, with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and as directed.

S & F in replacement MCB single pole and neutral 240 volt any rating from 63 Amps "C" series, with rupturing capacity 10 KA inculding providing thimble for out going cable complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. including taking down old sub main wire complete all as specified and as directed.

Supply and fixing LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers along with all electrical wire connection complete all as specified and as directed.

Supply and fix ceiling fan, AC single Phase. 230V of size 1200mm sweep with, blades, and frame along with all electrical wire connection complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5 connected to main control board all as specified and testing on completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc.Note: if earth resistance of earthing is not found (2 to 5 Ω) satisfactory if will be redone by the contractor on his risk and cost complete all as specified and as directed.

Material and labour for Fixing & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size all as specified including taking down old cable.Note : Earth work and other connected work shall be measured & paid sperately complete all as specified and as directed.

Material & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 10 Sqmm x 4 core size all as specified including taking down old cable.Note : Earth work and other connected work shall be measured & paid sperately complete all as specified and as directed.

Excavation in trenches and exceeding 1.5m wide and not exc 1.5m in depth in hard/dense soil and getting out complete all as specified and as directed.

Returing, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed.

Removing excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and as directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed.

Sheet metal enclosure double door type for DBs (when MCB to be used) 12 way 240 volts with 200 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

MCB Single pole and neutral 240 volt any rating from 40 amps 'C' series, with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and as directed.

MCB single pole 240 volt any rating from 10 to 40 amps 'C' series, with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 230V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

36W (2 x 2) LED Ceiling/recess light panel for recess mounting warm white colour which provides soft-light and glare free symmetrical illumination complete all as specified and as directed.

Supply and fixing LED luminaire 15 watt, 220 V AC recess mounted downlighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp warm white suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

SINGH CONST CO

RAJ MOHD

jyoti parkash sharma

khajuria builders

VIRINDER SINGH