For Providing Electrification Work 1st Call. P. A. C. 2987820.00 on Electrical SOR 01-01-2024, Completion period 365 Days (i/c rainy season)

For Providing Electrification Work for AR/SR/ Deposit/MOW/OW in Govt. Residential (F and Below Type) and Non Residential Building at (Section 1100 Qtrs) Under PWD E/M Sub Division Workshop, Bhopal. (Detail Schedule Attached)

SECTION 4

BILL OF QUANTITIES (BOQ)

General Description of work: For Providing Electrification Work for AR/SR/ Deposit/MOW/OW in Govt. Residential (F and Below Type) and Non Residential Building at (Section 1100 Qtrs) Under PWD E/M Sub Division Workshop, Bhopal. 1st Call. P. A. C. 2987820.00 on Electrical SOR 01-01-2024, Completion period 365 Days (i/c rainy season)

Probable Amount of Contract :

(Rs. In Figure) :-

(Rs. In Words) :-

SOR.No

Dismantling of existing light/fan/ bell/socket out let point on separate board/wiring and circuit with insulated wire in casing/conduit/ batten complete with fitting and accessories

Making the site clear of the dismantled installation by refilling the hole with cement mortar & finished with paint gitties and replacing to match the colour& wall ceiling.

Dismantling of existing socket outlet point on same board in any system of wiring

Dismantling the existing armoured/unarmoured cable or 2/3/4 wires of submain, main, in any system of wiring including recoiling.

Dismantling of existing underground cable safely with its accessories and refilling the trench to ground level including recoiling of dismantled cable.

Dismantling of D.F. board, D.P. switch, T.P. & T.P.N. switch or D.B. of any size complete with board or angle/flat iron frame and making site clear including the refilling hole & repainting to match colour of wall.

Dismantling of D.F. board, D.P. switch, T.P. & T.P.N. switch or D.B. of any size only

Dismantling the existing ceiling/exhaust/cabin fan with complete accessories and making the site clear.

Dismantling of existing water tight fluorescent tube fitting with making the site clear.

Dismantling of existing water tight fitting S.V/M.H/L.E.D lamp fitting with extension bracket, clamp from pole or wall with making the site clear.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC FRLS insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :- Using flush type normal accessories

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point / fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. Socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Using flush type normal accessories

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point / fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside casing & capping screwless connector for joints etc. as required as per specification for :- Using flush type normal accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point / fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside casing & capping with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification for :- Using flush type normal accessories.

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification for :- Using flush type normal accessories.

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. casing and caping ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside capping, screwless connector for joints as per specification for :- Using flush type normal accessories.

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing concealed rigid conduit ISI marked of suitable size with PVC insulated FRLS copper earth continuity conductor of green colour, screwless connector for joints as per specification including earthing of regulator etc as required for :- Using flush type normal accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable copper stranded conductor ISI marked FRLS in existing surface rigid conduit ISI marked of suitable size with PVC insulated FRLS copper earth continuity conductor of green colour as per specification including earthing of regulator etc as required for :- Using flush type normal accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC FRLS insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :- Using modular accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point / fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. Socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Using modular accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point / fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside casing & capping screwless connector for joints etc. as required as per specification for :- Using modular accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point / fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside casing & capping with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification for :- Using modular accessories.

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification for :- Using modular accessories.

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. casing and caping ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside capping, screwless connector for joints as per specification for :- Using modular accessories.

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing concealed rigid conduit ISI marked of suitable size with PVC insulated FRLS copper earth continuity conductor of green colour, screwless connector for joints as per specification including earthing of regulator etc as required for :- Using modular accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable copper stranded conductor ISI marked FRLS in existing surface rigid conduit ISI marked of suitable size with PVC insulated FRLS copper earth continuity conductor of green colour as per specification including earthing of regulator etc as required for :- Using modular accessories.

Light point/fan points.

Primary short point

Primary medium point

Primary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Short point

Medium point

Long point

Supplying and fixing PVC conduit ISI marked FRLS along with accessories on surface etc. as required

PVC conduit 20 mm. (MMS)

PVC conduit 25 mm. (MMS)

Supply and fixing PVC conduit ISI marked FRLS along with the accessories in concealed system etc. as required

PVC conduit 20 mm. (HMS)

PVC conduit 25 mm. (HMS)

PVC conduit 32 mm. (HMS)

Supplying and fixing PVC casing and capping (double fold) ISI marked along with accessories on surface etc. as require

PVC casing and capping (double fold) 20 mm x 12mm

PVC casing and capping (double fold) 25 mm x 12mm

PVC casing and capping (double fold) 32 mm x 12mm

Supplying and fixing of approved make modular type G.I. metal box 1.2mm minimum thick and depth 50mm for single row boxes and 60mm depth for two/three row boxes earth terminal stud with nut and washer with modular base and cover plate including fixing in concealed etc. as required for:-

MS box 100 mm X 100 mm X 60mm

MS box 200 mm X 150 mm X 60 mm

MS box 180 mm X 100 mm X 60 mm

MS box 125 mm X 300 mm X 60 mm

MS box 200 mm X 250 mm X 60 mm

MS box 250 mm X 300 mm X 60 mm

MS box 300mm X 380 mm X 60 mm

Supplying and fixing factory fabricated hot dip galvanized switch box for normal flush type accessories of minimum 1.2 mm thickness for up to 200mmx250mm size boxes and 1.6mm minimum thickness for higher size boxes, earth terminal stud with nut and washer, including 3 mm thick synthetic phenolic resin bonded laminated sheet conforming to grade P-I of IS:20361974 on surface/concealed including all necessary accessories, painting etc. as required as per specification:

1Or 2 Module metal box

3 Module metal box

4 Module metal box

6 Module metal box

8/9 Module metal box

12 Module metal box

16 Module metal box

18 Module metal box

Supplying and fixing of approved make modular type PVC box minimum depth 40mm and minimum thickness 2mm with modular base and cover plate including fixing on surface etc. as required for:-

1Or 2 Module PVC box

3 Module PVC box

4 Module PVC box

6 Module PVC box

8/9 Module PVC box

12 Module PVC box

16 Module PVC box

Supplying and drawing single core PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing rigid PVC casing and capping/conduit in surface or concealed as per specification

1.5 sq. mm. wire

1 X 1.5 sq. mm.

2 X 1.5 sq. mm.

3 X 1.5 sq. mm.

4 X 1.5 sq. mm.

2.5 sq. mm. wire

1 X 2.5 sq. mm.

2 X 2.5 sq. mm.

3 X 2.5 sq. mm.

4 X 2.5 sq. mm.

4.00 sq. mm. wire

1 X 4.00 sq. mm.

2 X 4.00 sq. mm.

3 X 4.00 sq. mm.

6.00 sq. mm. wire

1 X 6.00 sq. mm.

2 X 6.00 sq. mm.

3 X 6.00 sq. mm.

10.00 sq. mm. wire

1 X 10.00 sq. mm.

2 X 10.00 sq. mm.

3 X 10.00 sq. mm.

Wiring for sub-mains with PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid PVC conduit (MMS) FRLS ISI marked of suitable size (conduit included) including 2mm thick accessories, connection etc, as required as per specification. (Refer General Notes for Classification of Conduit Wiring Point No.11)

2 Wire sub main

2.5 sq. mm. cable

4.0 sq. mm. cable

6.0 sq. mm. cable

3 Wire sub main

2.5 sq. mm. cable

4.0 sq. mm. cable

6.0 sq. mm. cable

10.0 sq. mm. cable

4 Wire sub main

2.5 sq. mm. cable

4.0 sq. mm. cable

6.0 sq. mm. cable

10.0 sq. mm. cable

Wiring for sub-mains with PVC insulated cable FRLS with copper multi strand conductor ISI marked in recessed/concealed rigid PVC conduit (HMS) FRLS ISI marked of suitable size (conduit included) including 2mm thick accessories, connection etc, as required as per specification. (Refer General Notes for Classification of Conduit Wiring Point No.11)

2 Wire sub main

2.5 sq. mm. cable

4.0 sq. mm. cable

6.0 sq. mm. cable

3 Wire sub main

2.5 sq. mm. cable

4.0 sq. mm. cable

6.0 sq. mm. cable

4 Wire sub main

2.5 sq. mm. cable

4.0 sq. mm. cable

6.0 sq. mm. cable

10.0 sq. mm. cable

Rewiring in existing surface/concealed rigid steel/PVC nonmetallic conduit with PVC insulated cable with copper multi strand conductor FRLS of ISI marked and other materials as required including replacement of wornout/damaged/missing material, painting etc. complete as per specification. This shall include all work, arrangement required for wiring but shall exclude switch, ceiling rose, fitting etc.

Light/fan/3 Pin 6 Amp socket outlet on separate board/call bell/buzzer points :-

Short point

Medium point

Long point

Twin control light point

Short point

Medium point

Long point

Circuit wiring

2 X 1.5 sq. mm.

2 X 2.5 sq. mm.

3 Pin 6 Amp socket outlet point on same board

2 Wire sub main

2 X 2.5 sq. mm.

2 X 4.0 sq. mm.

2 X 6.0 sq. mm.

2 X 10.0 sq. mm.

2 X 16.0 sq. mm.

3 Wire sub main

3 X 2.5 sq. mm.

3 X 4.0 sq. mm.

3 X 6.0 sq. mm.

3 X 10.0 sq. mm.

3 X 16.0 sq. mm.

3 X 25.0 sq. mm.

3 X 35.0 sq. mm.

3 1/2Wire sub main

3 x 2.5 + 1 x 1.5 sq. mm.

3 x 4.0 + 1 x 2.5 sq. mm.

3 x 6.0 + 1 x 4.0 sq. mm.

3 x 10.0 + 1 x 6.0 sq. mm.

3 x 16.0 + 1 x 10.0 sq. mm.

3 x 25.0 + 1 x 16.0 sq. mm.

3 x 35.0 + 1 x 25.0 sq. mm.

4 Wire sub main

4 X 2.5 sq. mm.

4 X 4.0 sq. mm.

4 X 6.0 sq. mm.

4 X 10.0 sq. mm.

4 X 16.0 sq. mm.

4 X 25.0 sq. mm.

4 X 35.0 sq. mm.

Supply of I.S.I. marked iron clad/metal clad triple pole and neutral switch fuse (conduit entry)/cable gland entry with two earthing terminals –

16Amp 415/500 Volts.

32Amp 415/500 Volts.

63Amp 415/500 Volts.

Supply & fixing of I.S.I. marked porcelain rewireable fuse unit of approved make or conforming to I.S. 2086-1982

16Amp/415 Volts or 32Amp/240 Volts

32Amp/415 Volts

63Amp/415 Volts

100Amp/415 Volts

Supply of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard conforming to IS – 8828

MCCB current rating – upto 63 Amp, 10kA, 3P 415V AC

MCCB current rating -80 to 100Amp, 10kA, 3P 415V AC

MCCB 25kA current rating, 3P -25 to 100Amp & 80% -100% adjustable

MCCB 25kA current rating, 3P -125Amp & 80% -100% adjustable

MCCB 25kA current rating, 3P -160Amp & 80% -100% adjustable

MCCB 25kA current rating, 3P -200Amp & 80% -100% adjustable

MCCB 36kA current rating, 3P -160Amp &adjustable: 80% -100% thermal

MCCB 36kA current rating, 3P, 3P 200Amp &adjustable: 80% -100% thermal

Supplying of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, (Ics=100%Icu) AC supply with thermal - magnetic release having respective breaking capacity (KA) at 415 Volts cited against their range standard conforming to IS/IEC 60947-

MCCB 25kA current rating - 63 to100Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 3 Pole

MCCB 25kA current rating - 125Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 3 Pole

MCCB 25kA current rating - 160Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 3 Pole

MCCB 25kA current rating - 200Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 3 Pole

MCCB 36kA current rating - 160Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 3 Pole

MCCB 36kA current rating - 200Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 3 Pole

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :-

Single pole

MCB SP 0.5Amp to 5Amp 10kA rating

MCB SP 6Amp to 32Amp 10kA rating

Double pole

MCB DP 0.5Amp to 5Amp 10kA rating

MCB DP 6Amp to 32Amp 10kA rating

MCB DP For 40Amp 10kA rating

For Triple pole

MCB TP 0.5Amp to 5Amp 10kA rating

MCB TP 6Amp to 32Amp 10kA rating

MCB TP For 40Amp 10kA rating

MCB TP 50Amp to 63Amp 10kA rating

Four pole

MCB FP 0.5Amp to 5Amp 10kA rating

MCB FP 6Amp to 32Amp 10kA rating

MCB FP For 40Amp 10kA rating

MCB FP 50Amp to 63 Amp 10kA rating

Supplying of MCB Isolators suitable for 240/415 Volts, 50 Hz AC supply with kA value rating 10 kA of approved make conforming to IS:13947-Part III :1993 & IEC:60947- 3:2001 (without enclosures ) :-

Single pole

Current rating upto 40Amp

Double pole

Current rating upto 40Amp

Current rating upto 63Amp

Triple pole

Current rating upto 63Amp

Current rating upto 80Amp

Current rating upto 100Amp

Four pole

Current rating upto 63Amp

Current rating upto 80Amp

Current rating upto 100Amp

Supply of approved make powder coated sheet steel encloser SPN MCB DB inclusive of busbar, neutral bar, earth bar, connection copper wire not less than 16 sq.mm & two earth terminals etc. complete as per IS:13032(exclusive of MCB & isolator)-

2 Way single door

4 Way single door

4 Way double door IP 43 protection

6 Way double door IP 43 protection

8 Way double door IP 43 protection

12 Way double door IP 43 protection

Supplying of approved make TPN MCB DB metal double door IP 43 protection with provision for FP MCB/ Isolator/ RCCB/ RCBO as incomer and SP MCBs as outgoing inclusive of busbar, neutral bar, earth bar, connection copper wire not less than 16 sq.mm & two earth terminals etc. complete as per IS:13032(exclusive of MCB & isolator):

Supplying of approved make vertical TPN MCB DB metal double door IP 43 protection with provision for FP MCB/Isolator/RCCB/RCBO as incomer and SP/TP MCBs as outgoing inclusive of busbar, neutral bar, earth bar, & two earth terminals etc. complete as per IS:13032(exclusive of MCB & isolator)

Supplying of approved make, powder coated metal double door vertical TPN MCB DB IP 43 protection with provision for MCCB upto160A TP/FP 36kA as incomer and space for SP/TP MCBs as outgoing (without MCCB/MCBs) inclusive of busbar & connections etc

4 Way without MCCB

6 Way without MCCB

8 Way without MCCB

12 Way without MCCB

Supplying & fixing of approved make Industrial type metal plug & socket DBs (without MCB) SPN sheet encloser (dust protected) inclusive of 2 pole and earth metal plug and socket and space to incorporate SP MCB complete as per specification as required.

Fixing of MCB/MCCB/Isolator in sheet steel enclosure as required as per accepted practice, including mounting on busbar and cable connection etc. complete (labour only)

MCB/Isolator SP/DP

MCB/MCCB Isolator TP/TPN/FP

Labour charges for fixing sheet steel enclosure, MCB DB surface mounting type, as per accepted practice on 25x5mm flat iron clamp duly embedded in wall, cable connection etc. complete.

For item no :-

Labour charges for fixing sheet steel enclosures, MCB DB surface mounting type, as per accepted practice on 25x25x 5 mm angle iron clamp, including supplying and fixing of clamp duly embedded in wall, cable connection etc. complete :-

For item no :-

27.11.6 & 27.11.7; 27.12.5 ; 27.13.2 to 27.13.4 & 27.14.1 to 27.14.4 ; 27.15.1 to 27.15.4

Labour charges for fixing sheet steel enclosures, MCB/MCCBDB flush mounting type, as per accepted practice, duly embedded and end plate completely flushed in wall, cable connection etc. complete :-

For item no :-

27.12.4 & 27.12.5 ; 27.13.2 to 27.13.4 ; 27.14.1 to 27.14.4 & 27.15.1 to 27.15.4

Supply and fixing as per specification pendent holder of approved make including flexible cord up to 3 metre length with necessary materials complete

Supply and fixing as per specification polycarbonate batten holder/angle holder of approved make with necessary materials complete

Supply and fixing as per specification call bell/buzzer of approved make with necessary materials complete.

Gong bell

Buzzer

Ding dong bell

Multi sound bell

Remote/cordless bell

Supply and fixing as per specification modular call bell indicator 230Volt A.C. including reset and buzzer of approved make with necessary materials complete.

Bell indicator with reset(1 Module) 250Volt

Buzzer modular (2 Module)

AUDIO CABLES

Supply and fixing of PVC insulated copper flexible speaker wire twin FRLS 1100 Volts as per IS:694-1990 of approved make

(24/0.2 mm) Twin core 0.75 sq.mm.

(32/0.2 mm) Twin core 1.00 sq.mm.

Supply and fixing of multi core round FRLSH PVC insulated copper (flexible) conductor & PVC sheathed cables 1100Volts as per IS:694-1990 of approved make

(16/0.2 mm)Three core 0.5 sq.mm.

(24/0.2 mm) Three core 0.75 sq.mm.

(30/0.25 mm) Three core 1.5 sq.mm.

(50/0.25 mm) Three core 2.5 sq.mm.

(56/0.3 mm) Three core 4.0 sq.mm.

Supply and fixing in position LED lamp of approved make

0.5 Watt250Volt of required colour lamp

3 Watt250Volt

5 Watt250Volt

7 Watt250Volt

9 Watt250Volt

12 Watt250Volt

15 Watt250Volt

18 Watt250Volt

25/27 Watt 250Volt

35/40 Watt 250Volt

45 Watt 250Volt

50 Watt 250Volt

Supply and fixing of rechargeable inverter LED Bulb, reduces to 40-50% (emergency application) with Lithium Ion battery 2600mAh, backup upto 5 hrs. having color temp upto 6500K, IP- 20 rating, THD (Total harmonic distortion) <20%

7W, Rechargeable Inverter LED Bulb

9W, Rechargeable Inverter LED Bulb

Supply and fixing as per specification Switch of approved make ISI marked with necessary material complete.

6Amp SP 250 Volt deluxe (piano key type)

16/20Amp SP 250 Volt deluxe (piano key type)

6Amp SP 250 Volt two way F/T

6/10Amp SP 250 Volt modular switch

16/20Amp SP 250 Volt modular switch

10Amp SP 250 Volt modular switch 2 way

32 Amps D.P.250 Volt modular switch with indicator LED 2 Module

Blank plate 1 module

Surface switch 6Amp

Supply and fixing as per specification socket outlet of approved make & ISI marked with necessary material complete

6Amp 250 Volt 3 Pin flush type

16Amp 250 Volt 3 Pin flush type

10Amp 250 Volt 3 Pin modular type

10/16/20Amp 250 Volt 3 Pin modular type

Supply and fixing as per specification 6Amp 250Volt bell push switch of approved make ISI marked with necessary material complete.

6/10Amp SP 250 Volt modular switch bell push

Flush type bell push

Surface bell push 6A

Supply and fixing as per specification switch socket combined of approved make & ISI marked with necessary material complete

20/10Amp 250Volt 3/6 Pin flush type

Supply and fixing as per specification polycarbonate ceiling rose 3 plate of approved make ISI marked with necessary material complete.

Supply and fixing of approved make 3 pin plug top ISI marked

6Amp 250Volt 3 Pin top

16Amp 250Volt 3 Pin top

Supply, fixing and testing of MPP condenser 440 Volt single phase of approved make as required as per specification

Condenser 2.5 mfd 440Volt

Condenser 3.15 mfd 440Volt

Condenser 4.00 mfd 440Volt

Condenser 6.00 mfd 440Volt

Supply and fixing of approved make flush type step type electronic fan regulator including connection etc. as required on existing board

Supply and fixing of approved make step type modular electronic fan regulator including connection etc. as required on existing board

100 Watt (1 module)

100 Watt(2 module)

Supplying, erection and testing of approved make electric Ceiling fan of double ball bearing complete with standard down rod, canopy, hanging shackle, Aluminium blades, without regulator, A.C. 230-250 volts including connections with all necessary material complete of approved as required confirming to IS :374/2019 with upto date amendments.

Ceiling fan - 900 mm sweep

Ceiling Fan (ISI marked)-1200 mm Sweep, with minimum air delivery 210 m³/min and service value ≥ 4.00 as per BEE..

Ceiling Fan ( ISI marked )-1400 mm Sweep, minimum air delivery 245 m³/min and service value ≥ 4.10 as per BEE.

Ceiling Fan Ornamental 1200 mm Sweep, with minimum air delivery 210 m³/min and service value ≥ 4.00 as per BEE.

Supplying, erection and testing of approved make wall mounting fan oscillating type with base, blades, guard, speed regulator etc. AC 230-250 volts with connections and including raw bolt/anchor hole fastener etc. complete finished and as required.

300 mm sweep

400 mm sweep

Supplying, erection and testing of approved make cabin fan oscillating type with base, blades, guard, speed regulator etc. AC 230- 250 volts with connections and including raw bolt/anchor hole fastener etc. complete finished and as required.

300 mm sweep

Supplying, erection and testing of approved make 'Fresh air fan' AC 230-250 volts with connection and including frame bolt/anchor hole fasteners etc. complete finished and as required.

225 mm sweep bush type

300 mm sweep bush type

225 mm sweep double ball bearing

300 mm sweep double ball bearing

Supplying and fixing of deluxe fresh air fan with louvers (ventilating fan) with self- closing louvers of decorative PVC blades mounting square frame of approved make complete with all necessary material as required

150mm RPM1300/1400

200mm RPM1300/1400

250mm RPM1300/1400

300mm RPM1300/1400

Supplying, erecting and testing of approved make exhaust fan heavy duty with mounting frame, blades AC 230-250 complete connection and including, frame bolt/anchor hole fasteners etc. complete finished and as required.

300mm sweep RPM 900 / 1400

380mm sweep RPM 900 /1400

450mm sweep RPM 900 / 1400

Supplying and testing of approved make Pedestal fan A.C. 230-250 volts with blades speed regulator 'pedestal etc duly wired with all necessary material complete as required

400 mm Sweep

Supplying, erection and testing of approved make air circulator fan A.C. 230-250 volts with blades speed regulator etc duly wired with all necessary material complete as required

Air circulator wall mounting fan

450 mm sweep

600 mm sweep

Air circulator pedestal fan

450 mm sweep

600 mm sweep

Supply and fixing M.S. down rod 14 SWG (2mm) thick for ceiling fan including threading, painting, making holes etc. as required complete. Note: For new works difference of installed & standard down rod length shall be paid.

Supplying, fixing & testing of approved make of non - integral type CFL roadway lighting consisting of powder coated sheet steel housing with epoxy white powder coated CRCA sheet steel gear tray, clear acrylic cover complete with all accessories (without lamp) including fixing on existing G.I. pipe, pole with connection and all required material suitable for -

For 1 x 85W Retrofit CFL/LED (Without control gear)

Supply, fixing & testing of approved make globe type polycarbonate post top lantern, consisting of cast aluminium spigot complete with all accessories, lamp holder, (without lamp) including fixing on gate pillars/exiting G.I. pipe, pole with connection & all required materials on existing required size of G.I. pipe, suitable for CFL/LED lamp for mentioned below sizes :-

Supply and fixing Led tube rod comprising of LED tube with non-integral/integral driver, upto 6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be minimum with system efficacy> 100 lm/Watt. LED driver PF> 0.95 & THD < 20%. The colour rendering index of LED light should be more than 70. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

Tube light LED 1 X 8/10Watt Integral i/c batten aluminium body, PC diffuser.

Tube light LED 1 X 12Watt Integral i/c batten aluminium body, PC diffuser.

Tube light LED 1 X 18Watt, Integral i/c batten aluminium body, PC diffuser.

Tube light LED 1 X 20/22Watt, Integral i/c batten aluminium body, PC diffuser.

LED retrofit glass tube i/c driver only 20/22Watt,color temp 3000 - 6000K without box suitable for replacing existing 36/40Watt FTL

Supply and fixing of recessed mounting type Led light fixture, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF> 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

LED luminiare 2' X 2', 36Watt, color temp 3000-6500k as required.

LED luminiare 2' X 2', 42/45Watt, color temp 3000-6500k as required.

Supply and fixing of surface mounting type LED light fixture, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver, PF> 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

LED luminiare 2' X 2', 36Watt, color temp 3000-6500k as required.

LED luminiare 2' X 2', 42/45Watt, color temp 3000-6500k as required.

Supply and fixing recessed mounting LED down lighter, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job..

3 Watt, color temp 3000-6500k as required.

5/6 Watt, color temp 3000-6500k as required.

7/8/10 Watt, color temp 3000-6500k as required.

12 Watt, color temp 3000-6500k as required.

14/15 Watt, color temp 3000-6500k as required.

18/20Watt, color temp 3000-6500k as required.

22/24Watt, color temp 3000-6500k as required.

Supply and fixing surface mounting LED down lighter, LED of 1 to 3Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job..

3 Watt, color temp 3000-6500k as required.

5/6 Watt, color temp 3000-6500k as required.

7/8/10 Watt, color temp 3000-6500k as required.

14/15 Watt, color temp 3000-6500k as required.

18/20 Watt, color temp 3000-6500k as required.

21/22/24Watt, color temp 3000-6500k as required.

Supply and fixing of recessed mounting LED swivel type COB downlighter, having color temp upto 6500K & having 20000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>80lm/W. LED driver PF > 0.9, THD < 20% & surge protection 5KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium / CRCA powder coated frame with glare free diffused polycorbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory. i/c connection wire, testing etc. to complete the job. Guarantee as per tender agreement condition.

Supply and fixing of Linear profile suspended LED lumanaire, having color temp upto 6500K & having 20000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>80lm/W. LED driver PF > 0.9, THD < 20% & surge protection 5KV. The colour rendering index of LED light should be more than 80. Housing made of pressure die cast aluminium / CRCA powder coated frame with high transmission diffuser. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory. i/c mounting arrangment, connection wire, testing etc. to complete the job. Guarantee as per tender agreement condition.

Supply and fixing of Linear profile suspended LED lumanaire, having color temp upto 6500K & having 20000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>80lm/W. LED driver PF > 0.9, THD < 20% & surge protection 5KV. The colour rendering index of LED light should be more than 80. Housing made of pressure die cast aluminium / CRCA powder coated frame with high transmission diffuser. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory. i/c mounting arrangment, connection wire, testing etc. to complete the job. Guarantee as per tender agreement condition.

Supply and fixing integral post top lantern LED fitting comprises of copper dust finish cast aluminium spigot and spun aluminium canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting, open construction driver and accessories are wired upto terminal block. LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100lm/Watt. LED driver PF > 0.95 & surge protection 10KV. The colour rendering index of LED light should be more than 70. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

40 Watt LED, color temp 3000-6500k as required.

25 Watt LED, color temp 3000-6500k as required.

Supply and fixing street light with high power LED of 3 to 6 W each on existing bracket assembled on single MCPCB, system lumens output with efficacy>120 lm/W. luminiare having color temp upto 6500K & 50000 burning hrs. life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare comprises of driver, PF> 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass/Lens type, IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

15Watt to 20Watt, color temp 3000-6500k as required.

24Watt to 25Watt, color temp 3000-6500k as required.

Supply and fixing street light with high power LED of 3 to 6 Watt each on existing bracket assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy>120 lm/Watt. luminiare having color temp upto 6500K & 50000 hrs. burning life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare comprises of driver, PF> 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass, IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347 i/c connection wire, testing etc. to complete the job.

40Watt to 48Watt, color temp 3000-6500k as required.

60Watt, color temp 3000-6500k as required.

90Watt, color temp 3000-6500k as required.

120Watt, color temp 3000-6500k as required.

150Watt, color temp 3000-6500k as required.

Supplying and fixing flood light with high power LED of 3 to 6 Watt each assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy>120 lm/Watt. luminiare having color temp upto 6500K & 50000 hrs. burning life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare comprises of driver, PF > 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass, IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

10Watt, color temp 3000-6500k as required.

30Watt, color temp 3000-6500k as required.

60Watt, color temp 3000-6500k as required.

90/100Watt, color temp 3000-6500k as required.

120Watt, color temp 3000-6500k as required.

150Watt, color temp 3000-6500k as required.

180Watt, color temp 3000-6500k as required.

250Watt, color temp 3000-6500k as required.

300Watt, color temp 3000-6500k as required.

Supply, Installation testing and commissioning of red colour aviation light LED integral type comprising of aluminium powder coated housing with polycarbonate enclosure IP 65 on existing pipe/support including connection, testing etc. as required. Guarantee as per tender agreement condition.

20 watt (300 LED)

Supply, fixing & testing of approved make of LED integral type bollard cylindrical/square shape housing cast aluminium dome shape top cover fixed with cylindrical shape acrylic cover having base plate with holes for direct mounting complete with all accessories including preparation of foundation, fixing, connection etc. as required. LED of 1 to 3 Watt each assembled on single MCPCB, system lumens output with efficacy>90 lm/W. luminaire having color temp upto 6500K & 50000 burning hrs. life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare, comprises of driver PF> 0.95 & surge protection 10KV. IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

Bollard LED 8-10 Watt cylindrical shape height > 700mm, color temp 3000-6000k

Bollard LED 8-10 Watt mushroom shape height > 600mm, color temp 3000-6000k

Supplying, fixing & testing of approved make flexible LED strip comprising of 60 LED per meter W/O driver for direct mounting complete with all accessories including connection lead, fixing, connection as required. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

Flexible LED strip 24Watt/25Watt - 5 M indoor cove light W/O Driver IP 20 -33

Flexible LED strip 72Watt/75Watt - 5 M indoor light W/O driver IP 20 - 33

Flexible LED strip 24Watt/25Watt - 5 M outdoor cove light W/O driver IP65

Flexible LED strip 72Watt/75Watt - 5 M outdoor light W/O driver IP65

Supplying, fixing & testing of approved make Power supply for LED strip

Power supply 25Watt/30Watt for LED strip IP25/IP33

Power supply 48Watt for LED strip IP33

Power supply 72Watt/75Watt for LED strip IP25/IP33

Power supply 25Watt/30Watt for LED strip IP65

Power supply 48Watt for LED strip IP65

Power supply 72Watt/75Watt for LED strip IP65

Supplying, fixing and testing of approved make LED bulkhead ABS body, PC diffuser including fixing on wall as required, with necessary material complete

Supply, fixing and testing of approved make integral step/skirt LED light suitable for 3 module box and plate including fixing on wall as required, with necessary material to complete the job. Guarantee as per tender agreement condition.

Supplying and fixing LED fire signage i/c 6V. 9AH, lithium battery sealed 2hrs backup single side, hanged/fixed on wall or ceiling etc. as required with necessary material to complete the job. Guarantee as per tender agreement condition.

Supplying and fixing LED fire signage i/c 6V. 9AH, lithium battery sealed 2hrs backup double side hanged/fixed on wall or ceiling etc. as required with necessary material to complete the job. Guarantee as per tender agreement condition.

Fixing of street light bracket of required angular shape and size pipe bracket on wall/pole including M.S. clamp not less than 40X5mm flat, nut, bolt 12mm of required length with necessary material including connection 3 core flexible wire etc. complete as required excluding cost of pipe paid separately.

Supplying Fixing and testing of approved and suitable make LED driver for an existing LED luminary panel.

LED Luminiare 1'x1', 24W Panel Driver

LED Luminiare 2'x2', 36W Panel Driver

Supplying fixing and testing of approved and suitable make LED driver for an existing LED street light.

24Watt to 25Watt, color temp 3000-6500k

40Watt to 48Watt, color temp 3000-6500k

60Watt, color temp 3000-6500k

90Watt, color temp 3000-6500k

120Watt, color temp 3000-6500k

150Watt, color temp 3000-6500k

Supplying, fixing and testing of approved and suitable make LED driver for an existing LED Flood light.

60Watt, color temp 3000-6500k

90Watt, color temp 3000-6500k

120Watt, color temp 3000-6500k

150Watt, color temp 3000-6500k

Supplying and fixing fan clamp of 12 mm dia steel bar as per specification complete.

For stone slab roof "J" Type hook

For R.C.C. slabs/beams

For existing R.C.C. slabs/beams

Servicing & overhauling of cooler fan motor, pump including replacement of distribution, delivery pipes, PVC elbows, painting etc. as reqd. complete with necessary material & labour.

Rewinding of fans by copper enameled wire of suitable gauge including all required material, insulation, varnishing, connection leads, oiling .greasing etc complete with testing including dismantling & refitting of fan at site. Scrap old material is not returnable to the department.

Ceiling fan 1400 mm sweep old model/exhaust fan 450 mm sweep

Ceiling fan 1400 mm sweep new model/exhaust fan 380 mm sweep

Ceiling fan 1200 mm sweep old model/cooler fan 500 mm (20")sweep

Ceiling fan 1200 mm sweep new model/exhaust fan 300 mm sweep

Fresh air fan up to 300 mm sweep/wall bracket/cabin fan 400 mm sweep

Cleaning, overhauling, servicing of ceiling/exhaust/wall bracket fan by applying grease & oil, including testing with mounting/hanging arrangement including replacement of safety pins, check nuts, lock nut, nut bolts etc. making perfect alignment & refitting at site as required.

Earthing with G.I. earth pipe 4.5 metre long and 40 mm dia with masonry encloser in cement mortar, cover plate having locking arrangement on the top etc. (but without charcoal or coke and salt) complete as required

Add extra for using salt and charcoal/coke for pipe earth electrode as required including excavation & refilling

Excavation 4.5 m by manual labour

Excavation by making hole with auger

Earthing with G.I. earth plate 600mm X 600mm X 6mm thick including accessories and providing masonry encloser in cement mortar, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 metre long etc. (but without charcoal or coke and salt) complete as required

Earthing with copper earth plate 600mm X 600mm X 3mm thick including accessories and providing masonry encloser in cement mortar, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 metre long etc. (but without charcoal or coke and salt) complete as required

Add extra for using salt and charcoal/coke for G.I. plate or copper plate earth electrode as required including excavation and refilling the pit in all type of soil, murrum

Add extra for using salt and charcoal/coke for G.I. plate or copper plate earth electrode as required including excavation in hard rock and refilling the pit with black soil.

Supply and laying 4.0mm (8 SWG) dia. G.I. wire at 0.5 metre below ground level as conductor earth electrode including jointing etc. as required.

Supply and laying 4mm dia. copper wire at 0.5 metre below ground level as conductor earth electrode including soldering etc. as required.

Supply and laying 4.87mm 6 SWG G.I. wire at 0.5 metre below ground level as conductor earth electrode including jointing etc. as required.

Supply and laying 25mm X 5mm G.I. strip at 0.5 metre below ground level as strip earth electrode including jointing etc. as required.

Supply and laying 25mm X 6mm G.I. strip at 0.5 metre below ground level/surface as strip earth electrode including jointing etc. as required.

Providing and fixing 25mm X 5mm copper strip in 40 mm dia G.I. Pipe from earth electrode as required

Providing and fixing 25mm X 5mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required

Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15mm dia G.I. Pipe from earth electrode as required.

Providing and laying earth connections from earth electrode with 4.00 mm dia copper wire in 15mm dia G.I. Pipe from earth electrode as required.

Providing and fixing 25mm X 5mm copper strip on surface or in recessed for connection etc. as required

Providing and fixing 25mm X 5mm G.I. strip on surface or in recessed for connection etc. as required

Providing and fixing 4.0mm (8 SWG) dia G.I. wire on surface or in recessed for loop earthing as required

Providing and fixing 4.87mm (6 SWG) dia. G.I. wire on surface or in recessed for loop earthing as required

Providing and fixing 4.00mm copper wire on surface or in recessed for loop earthing as required

Supply and laying 50mm X 6mm G.I. strip at 0.5 metre below ground level/surface as strip earth electrode including jointing etc. as required.

Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make.

2.5 sq.mm multi strand

4.0 sq.mm multi strand

6.0 sq.mm multi strand

10.0 sq.mm multi strand

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor

Unarmoured 2 core

Armoured 2 core

Armoured 3 core

4 core armoured

Supplying & installing G.I. pipe for protection of underground cable fixed on wall/support/in trench/fixed between two rigid existing support of wall/beam for erection of ceiling Fan/down rod for stiff pendent for light luminaries /fan/protective for earthing, lightening conductor down strip/overhead service line/for submersible cable or centrifugal pump for water supply with necessary iron clamp coupler, bend, tee, elbow, nuts and bolts etc. complete in an approved manner as required to complete excluding cost of excavation/dismantling & other finished masonry Item complete.

For 'B' class pipe ISI marked (IS-1161- 68)

Cable laying

Laying of one number armoured / unarmoured power cable 1.1KV grade of size not exceeding 25 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, sand cushioning, protective covering and refilling the pit etc. as required.

Laying of one number armoured / unarmoured power cable 1.1.KV grade of size exceeding 25sq. mm but not exceeding 120 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, sand cushioning, protective covering and refilling the pit etc. as required.

Laying of one number additional armoured / unarmoured power cable 1.1KV grade of size not exceeding 25sq. mm direct in ground in the same trench in one tier horizontal formation including excavation in all soil/murrum/soft rock, sand cushioning protective covering and refilling the pit etc. as required.

Laying of one number additional armoured / unarmoured power cable 1.1KV grade of size exceeding 25 sq. mm but not exceeding 120 sq. mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the pit etc. as required.

Laying of one number armoured / unarmoured power cable 1:1 KV grade of size not exceeding 25 sq. mm in the existing RCC hume/stone ware/G.I. pipe/surface in existing trench as required.

Laying of one number armoured / unarmoured power cable 1.1 KV grade of size exceeding 25 sq. mm but not exceeding 120 sq. mm. in the existing RCC Hume /Stone ware/G.I. Pipe/surface in existing trench as required.

Laying of one number armoured / unarmoured power cable 1.1 KV grade of size not exceeding 25 sq. mm in the existing masonry open duct as required.

Laying of one number armoured/unarmoured power cable 1.1KV grade of size exceeding 25sq. mm but not exceeding 120 sq. mm in the existing masonry open duct as required.

Laying of one number armoured/unarmoured cable 1.1KV grade of size not exceeding 25 sq. mm on surface in existing trench etc. as required.

Laying of one number armoured/unarmoured cable 1.1KV grade of size exceeding 25 sq. mm but not exceeding 120 sq. mm on surface in existing trench etc. as required.

Laying of one number armoured/unarmoured cable 1.1KV grade of size not exceeding 25 sq. mm on wall/truss with approved type of iron clamp etc. As required.

Laying of one number armoured/unarmoured cable 1.1KV grade of size exceeding 25 sq. mm but not exceeding 120 sq. mm on wall/truss with approved type of iron clamp etc. as required.

Laying of underground cable armoured./unarmoured as per specification in air suspended on existing approved type of iron clamp, G.I wire 7/1.6mm & shackle insulator/insulated strip complete.

1/2/3/4 Core cable upto 16 sq. mm

1/2/3/3½/4 Core cable 25 sq. mm to 120 sq. mm

Total Rs.

Executive Engineer PWD E/M Division No. 1, Bhopal