Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹4.5 LAccepted-AOC SHREE RAM WARD PURANI BASTI BALLARPUR CHANDRAPUR MAHARASHTRA | BALLARPUR | CHANDRAPUR | MAHARASHTRA | 442701 | L-1 | Accepted-AOC Lowest qualified bidder. Hence being awarded. | |
| 2 | L-2₹4.1 L+₹21,683.90 (5.64%)Rejected-AOC DESHPANDE WADI RAJURA CIVIL CONTRACTOR DIST CHANDRAPUR442905 | CHANDRAPUR | MAHARASHTRA | 442905 | L-2 | Rejected-AOC Not a qualified L1 bidder |
Tender Value
₹5.4 L
EMD Value
₹6,800
Closing Date
30 Sept 2022, 3:30 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Shri. Anil Thoorwal
OFFICE OF THE AREA GENERAL MANAGER WCL BALLARPUR AREA P.O. SASTI TA. RAJURA DIST. CHANDRAPUR (MS) PIN 442905
Making 3 no. Temporary security check post room at Pouni II Expansion OCM under Pouni Sub Area
2022_WCL_256471_1
ba3650-civ-e42-2022-23
Open Tender
Civil Works - Buildings
Item Rate
90 days
WCL Ballarpur Area
As per NIT
3 documents required · 3 mandatory
₹6,800
12 Nov 2022
16 Sept 2022
1 Oct 2022
16 Sept 2022
30 Sept 2022
16 Sept 2022
16 Sept 2022 - 23 Sept 2022
120 days
Amount
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
Carriage of earth/OB by mechanical transport including loading unloding and stacking at site. Lead 1 km. lead
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1 : 3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources).
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources).
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level,excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beam, plinth beams, girders, bressumers and cantilevers.
Providing, hcisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
Brick work with fly ash bricks in foundation and plinth in cement morter 1:6 ( 1 cement : 6 coarse sand)
Brick work with clayt fly ash F.P.S (non modular) bricks of class designation 7.5 in superstructure above plinth level uptofloor five level in CM 1:6 ( 1 cement : 6 coarse sand)
Half brick masonary with fly ash bricks in foundation in cement mortar 1:4 (1 cement: 4 coarse sand)
Half brick masonary with fly ash bricks in superstructure in cement mortar 1:4 (1 cement: 4 coarse sand)
12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade:New work (two or more coats) over and including priming coat with cement primer.
Colour washing such as green, blue or buff to give an even shade : New work (two or more coats) with a base coat of white washing with lime
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.
Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete,including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed porion. Powder coated aluminium (minimum thickness of powde coating 50 micron)
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powde coating 50 micron)
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thick ness ( weight not less than 12.50 kg/sqm.)
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate
Supplying, erection & marking TPN MCB 40A to 63A, C-series in provided distrubtion board as per specification no. SW-SWR/MCB
Point wiring in PVC trunking (Casing-capping)with 1.5sqmm (2+1E) FRLSH grade copper wire, flush type switch earthing and required acacessories as per specification NO. WG-PW/SW.
Wiring for pug on board with switch socket with coper wiring and earting as per specification no WG-PW SW.
Supplying & erecting main with 2x2.5 sqmm. And earth wire 1.5sqmm FR pvc. Copper wire in HMS pvc. Conduit min 20mm dia, as per specification No. WG-MA/PC.
Supplying and erecting regulator/standard model ceiling fan of 900/1050mm sweep complete erected in position as per specification no. FG-FN/CF
Supplying and erecting LED 18W tube light fitting (4 feet ) with polycorbonate housing, heat sink integrated HF electronic driver complete.
Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected o provided plate and box with wirig connections complete note for additonal two moduler box with doube mounting plate if requied
Total impact of GST for the purpose of CTC
S K JHA
stage.html
html • 0.04 MB
techsummary_265171.pdf
PDF • 0.40 MB
finsummary_265171.pdf
PDF • 1.74 MB
Award-e42.pdf
PDF • 6.06 MB
BOQ Comparative Chart
xlsx • 0.01 MB
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .