SPECIAL REPAIR TO BLDG NO NP-01 TO NP-02 OR MD ACCN AND PROVN OF TOILET BLOCKS NEAR BLDG NO T-146 INCLUDING REVENUE WORK UNDER AGE B/R-II AND AGE BR-I OF GE (WEST) PATHANKOT (2ND CALL)

Amount

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.50 metre in depth for foundation etc and for manholes or laying of cable etc n.exc. 10 Sqm on plan and n.exc. 1.5 metre depth and getting out in any type of soil complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in Hard /dense Soil complete all as specified and directed.

All asper Srl item no. 3.00 here-in-before but depth exc 1.5 m but not exc 3 m

All asper Srl item no. 3.00 here-in-before but depth exc 3.00 m but not exc 4.5 m

All asper Srl item no. 3.00 here-in-before but depth exc 4.50 m but not exc 5.00 m

Removing excavated materials (soils) to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.50 above the starting point complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick as in soft/loose soil complete all as specified and directed.

Treating the top surface of filled earth at the rate of 7.50 litres of emulsion per square metre of surface complete all as specified and directed.

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Material & labour for approved soil filling under the floor, spreading and levelling in layers n.exc. 25cm thick, well ramming including watering as required complete all as specified and directed.

M&L loose filling with aggreagate of broken bricks , gauge 80mm to 150 mm for filling in soakage pit/ sokage wells complete all as specified and directed.

Material & labour for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finish surface of concrete complete all as specified and directed.

Use and waste of Form work of sides of pillars, posts, struts, piers, columns etc square or rectangular or polygonal rough surfaces of concrete complete all as specified and directed.

M&L Form work to sides and soffits of beams lintels etc finished rough complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick flat rough finished surfaces of concrete complete all as specified and directed.

M&Lfor form work to the edge of concrete flat n. exc 200 mm thick rough finish surface of concrete complete all as specified and directed.

Supply & fix mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Material and labour forMild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

All as per srl item no. 21.00 here-in-before but 6 to 8 mm dia and over, as in stirrups complete all as specified and directed.

M&L RCC M-25 Tybe A-1 using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M & L RCC M-25 Type A-1 using 20 mm graded stone aggregate as in Columns, pillars etc complete all as specified and directed.

M & L RCC M-25 Type A-1 using 20 mm graded stone aggregate as in beams, lintels over 1.5 m span etc complete all as specified and directed.

M&L for RCC M 25 type A-1 using 20 mm graded stone aggregate for roof slabs supported on walls, beams and the like complete all as specified and directed.

Material & labour brick work with fly ash bricks in CM 1;6 old size bricks straight or curved on plain exeeding 6m mean radius complete all as specified.

M&L for brick work with old size sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement and sand mortar 1:4 complete all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in cm 1:4 complete all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks in one and half brick thick honey comb walling, built in cm 1:4 complete all as specified and directed.

M&L 40mm thick DPC in cement concrete 1:2:4 type B-0 mixing with liquid water proofing admixture as per manufacturer instructions including necessary form work and applying evenly a coat of blown type bitumen at the rate of 1.5 kg per sqm and blinding clean dry sand @ 0.05 cum per sqm complete all as specified and directed. (WPA shall be measured & paid seperateley)

Supply only Liquid water proofing compound ISI marked all as in specified & directed.

Material & labour for 15 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM(1:4) surface finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for 5 mm thick plaster in CM 1:3 on ceiling surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick cement concrete 1:4:8 type D-2 using (40 mm graded stone agg) as in sub base complete all as specified and directed.

M&L Non Skid ceramic tiles 10 mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement joint free non skid tiles.to match and 15mm thick screed bed in CM 1:6 complete all as specified and directed

Material & labour for glazed coloured ceramic tiles of size 450x300x7-8mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/ coloured cement to match with existing work over and including 10mm thick rendering in CM 1:4 complete all as specified & directed.

M&L 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in path /plinth protection , finish even & smooth without using extra cement including necessary formwork all as specified and directed.

Material & labour for preparation of new plastered surfaces of walls etc and applying two coats of cement base paint over and including a coat of primer complete all as specified & directed.

Material and labour for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified & directed.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified & directed.

Material & labour for cleaning of plastered /concrete surfaces and Applying roof treatment on top of roof with APP modified membrane with non–woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of weight not less than 3.5 Kg/Sqm & thickness not less than 3mm, laid by torch application method with overlap 100mm on length side and 100mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS-3384) @ 0.30 Litre/Sqm and including 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instructions and ensure water does not stand anywhere after Sprinkle water on the roof surface complete all as specified.(Note:- WPC shall be measured and paid separately) Note: (a)Water proofing treatment shall be provided with APP modified membrane on plastered surface as per manufacturer’s instructions and under strict supervision of manufacturer technical representative.

M&L for Flat iron hold fast 25mm x 6mm welded to angle iron door frame complete all as specified and directed.

M&L for Mild steel angle iron door frame 40mmx40mmx6mm conforming to Fe 410-0 incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars & making good the floor in PCC 1:2:4 type B-0 to match the existing floor and treating the tie rod and back side of frame with black bitumennous paint complete all as specified and directed.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed togetter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 149 of SSR 2020 (Part-II) complete all as specified and directed.

Supply & fix 150mm size aluminium alloy handles cast type anodized complete all as specified & directed.

S&F aluminium tower bolts 150mm long, of extruded section complete all as specified and directed.

Supply & fix Aluminium. Sliding door bolts, plate type, complete, 250mm long complete all as specified and directed.

M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed.

S&F Steel window/ventilator factory made box type and shutter (double shuter) with sash bar made out of section using flash butt welding, complete including hinges ,tower bolt,handle , grill 10 mm sq bar including two coat of synthetic enamel paint over and including one coat of red oxide primer, tarred hold fasts, PCC blocks, including plain/figured glass and wire mesh 0.36 mm nominal dia of wire and average width of aperture 1.18 mm all as shown on drg No CEPZ /TD-245/01 sheet 1/1 and CEPZ /TD -246/01 sheet No 1/2 & 2/2 complete all as specified and directed. complete all as specified and directed

S&F 20mm thick Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply & fixing vitreous china wash hand basin, white, flat back of size 550x400mm counter Wash basin and 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed including brackets suitable for 15mm dia pipe including waste pipe 750mm long and CP waste coupling 32mm dia complete all as specified & directed.

S&F angular valve, 15 mm dia, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

S&F rotational moulded polyethylene water storage tanks 500 liters capacity, (cylindrical, vertical in closed top) ISI marked triple layered hoisted and fixed in position with all fittings all as specified & directed.

S&F PVC low level flushing cistern of 10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore, suitable for low level cistern complete all as specified & directed.

S&F 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

S&F 20 mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

S&F 3mm thick sheet glass, pin headed, and glazing with oil putty/beading in square not exceeding 0.50sqm each pane complete all as specified & directed.

S&F butt hinges, 100 mm long of stainless steel, complete all as specified & directed.

Supply & fixing PVC connections of 450mm long suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

S&F vitreous china squatting pan of ‘Orrisa pattern’ size 580x440mm, white with, integral foot rest including ‘P’ or ‘S’ trap, lime concrete bedding and making good floor complete all as specified and directed.

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F 110 mm bore PVC floor traps plain with grating and 300 mm long out let including jointing with cement concrete type B -1 1:2:4 complete all as specified & directed.

S&F PVC bends 110mm bore, any radius complete all as specified & directed.

S&F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls including clamps made of FI 25x3mm complete all as specified and directed.

PVC (SWR), junction single, (Single T) equal or unequal 110 mm bore complete all as specified and directed.

Supply & fixing vitreous china wash down water closet Pedestal pattern white alongwith plastic WC seat cover, white, closed pattern with flat bottom and cover and mild steel CP or aluminium hinging device complete all as specified and directed.

S&F CP brass jet spray with hand hold arrangement incl. 1.5m long flexible pipe with hook of superior quality complete all as directed.

S & F Vitreous china half stall urinal complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2,securing urinal to plugs with and including 60 mm long brass screws pointing around urinal back in cement including waste pipe 750mm long and CP waste coupling 32mm dia complete all as specified and directed.

S&F Tubular towel rail 20mm dia, D type, 60cm long between flanges Aluminium anodised complete all as specified and directed.

M&L 50mm thick PCC 1:2:4 type B-1 (20 mm graded aggregate) as in floor finished even & smooth without using extra cement complete all as specified and directed.

M&L 50mm thick PCC 1:2:4 type B-0 (12.5 graded grade aggregate) as in copings complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc complete all as specified and directed.

M&L for salt glazed stoneware drain pipe 150mm dia laid in trenches and jointed and tested complete all as specified and directed

M&L for 150 mm thick reinforced concrete pipes class NP3, laid and jointed with collars complete all as specified and directed

M&L unplastited drainage pipe 200mm dia type "B" with wall thickness 4mm(min) of pressure rating 8 KN/sqm laid in trenches and jointed with cement solvent including tsting complete all as specified and directed .

M&L for Concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested in Cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate for Bore of pipe in 200mm complete all as specified and directed

M&L for Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC(1:4:8) type D2 (using 40 mm graded stone aggregate) 150mm dia bore pipe complete all as specified and directed.

M&L for Precast cement concrete solid block in PCC 1:2:4 type B-1 using (20 mm graded aggregates) set in CM 1:4(size of precast concrete block as directed by GE) complete all as specified and directed.

M&L for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-35 Grade complete all as specified and directed

M&L Sand for cushioning for interlocking tiles joint to be filled with sand, including spreading and levelling in layers n exc 25 mm thick complete all as specified and directed.

Taking down chowkatts or frames with shutter (without taking off shutters from frame)exc 1.5 sq. m but n exc 4 sq m each complete all as specified and directed .

Taking down of wooden chowkats or frame with shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each complete all as specified and directed .

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and removing from site complete all as specified and directed.

M&L for Pressed steel frames of section 125 x 60 mm for doors with one or more rebates including supply and fixing lugs, hinges, lock strick plate etc complete all as specified.

M &L for pressed steel frames for doors with one or more rebates inclusing necessary fixing lugs, hinges, lock strike plate etc complete with profile size 105 x 60 mm, complete all as specified and directed.

Supply & fix 30mm thick flush shutter, solid core construction, with block board core and plywood face panels commercial type on both side complete all as specified and directed.

S&F 2nd class hard wood glazed and sketon door shutter 35 mm thick open rebated and prepared to receive glass/gauze (Without sash bars) divided into square with plain, chemfered or rounded, mitred and rebated sash bars the size of menbers of shutters as specified in SSR Part-I section 8 Clause 8.24 (a). complete all as specified and directed.

Supply & fix solid PVC door frame of size50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling fixing in opening as per specification & drawing complete all as specified & directed.

Supply & fixing in repair 140 mm size Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified & directed.

S&F Aluminium, anodised, barrel tower bolts of 200 mm long and 10mm dia stove enamelled black with bright bolt fixed complete all as specified and directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified

Supply & fixing 150 mm Aluminium handles, cast type, anodised fixed complete all as specified.

Supply & fixing Mild steel 300mm ordinary rat tail rod pattern spring including roller plate complete all as specified.

M&L for repairing of Hinges in old steel windows for repairing or welding drilling out old bolts or set screws as required. including repairing for handle pegstag, wiremesh and glass change, painting one coat etc area exc 1.00 sqm but n. exc 2.00 sqm each as servicable condition as per directed.

Supply & fix Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed .

M&L Preparation of new wooden surface of any descripion over 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed..

M & L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified including demolition/Taking of old sheets of any description complete all as specified & directed.

Dismantling timber scantling 40 Sq cm and over in section, in any position framed work complete all as specified & directed.

S & F mild steel angles/rectangular hollow section/steel tubular roof trusses (framed), purlines and fastening including distance pieces etc. complete all as specified and directed.

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc FE 290 (Gde E-165) complete all as specified & directed.

Demolition of brick work built in cement morter including all quoins, arches, pillars etc, complete all as specified & directed.

Taking down cement plaster on brick or concrete or stone walls etc including racking out joints hacking for key scrubbing down with water any description complete all as specified & directed.

Materials & labour for prepration of newely plastered surface and finishing the surfaces of wall with wall one coat wall care putty and applying two coat of Oil Bound distemper complete all as specified & directed.

Materials & labour for complete removal of existing treatmemt and finishing the surfaces of wall with wall care putty and applying two coat of Oil Bound distemper complete all as specified & directed.

M& L Complete removing existing treatment & applying over one Coat of Cement Primer of, any colour and two coats cement base paint complete all as specified & directed.

M&L for Washing, rubbing down and stopping of distempered and painted surfaces of wall and applying three coat white wash evenly complete all as specified.

Material and labour for complete removal of existing treatment from ceiling surface and applying two coat of white wash on undecorated surfaces without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

Demolition of Roofs, floors (other than ground floors), beams staircases, landing, cooking platform ,chajjas, & similar suspended work cement concrete is reinforced (reinforcement cut as required to facilitate demolition) and disposal of debris out of MoD land complete all as specified and directed. Note:- Demolition will be done only by mechanical cutter only.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15 cm thick ( above or below GL) complete all as specified

M&L for 25mm thick Cement concrete in sub base for receiving floor tiles/ topping layer using type B-0, 1:2:4 (using 20 mm graded crushed stone aggregate) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed .

Supply and fix non skid coloured Ceramic tiles 08mm thick (square/ rectangular) polished, area of each tiles 400 x 400x 8 mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

Supply and fix non skid coloured Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles 600 x 600 mm x 10 mm thick, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for non abrasive paving (endura) tiles 300mm x 300mm x10mm thick (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15mm screed bed CM 1:4 to match including 75mm thick sub base Plain cement concrete 1:4:8 type D-2 using 40mm graded aggregate complete al as specified and directed.Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L cement concrete type B-1 (1:2:4) using 20mm graded broken stone agg as coping, benching, cills, lintels up to 1.50 mtr clear span, filling around hold fast , fitting in chowkats etc complete all as specified and directed.

Demolition of existing roof treatment of any description such as worn-out tar felt, debris, mortar of any description & any thickness, surface cleaning of all foreign material such as fungus, moss, dust etc. by wire brushing and dusting including disposal of debris out of MoD land then surface levelled with a layer of 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instructions and ensure water does not stand anywhere after Sprinkle water on the roof surface including Applying roof treatment on top of roof with APP modified membrane with non–woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of weight not less than 3.5 Kg/Sqm & thickness not less than 3mm, laid by torch application method with overlap 100mm on length side and 100mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS-3384) @ 0.30 Litre/Sqm complete all as specified.(Note:- WPC shall be measured and paid separately) Note: (a)Water proofing treatment shall be provided with APP modified membrane on plastered surface as per manufacturer’s instructions and under strict supervision of manufacturer technical representative.

Supplied and fixing sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm complete all as specified and directed.

M&L Stainless steel plate rack(Utensil Rack) of size (900mm x 750mmx250mm ) made out of AISl 304 stainless steel 0.63 mm thick sheet fixed with brass screw of required size including necessary fittings/nuts,bolts & washers complete all as specified and as directed.

M&L for 20 mm thick granite (pure black) work (table rubbed and polished) as in cills, cooking platforms, in steps, jambs, pillars, window-cill and like set in cement mortar (1:4) 10mm thick including pointing in white cement in CM (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. Note : All Open Edges to be Half rounded.

M&L for two coat plaster 35 mm thick (20 mm + 15 mm) on rough concrete surfaces of fin, facia, chhajja and similar article in cm 1:3 finished even and smooth without using extra cement in any height including necessary scaffolding complete all as specified & directed. Note :- Two coat plaster shall be carried out as mentioned in clause 14.18 of SSR-2009, Part-I complete all as specified & directed.

S & F in repair curtain rails 25 mm dia of pre painted aluminium with fixing brackets, stops, rollers, knob etc complete all as directed

S&F 18mm thick ultra voilet printed PVC board (weight not less than 12 Kg/Sqm) duly edge bonded with 0.8mm thick PVC taping as in cupboard/kitchen cabinet shutters fitting complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2 (with using 40mm graded stone aggregate) as in floor and finishing even and spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specfied and directed.

S&F in repair 15mm Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixedcomplete all as specified & directed.

Supply & fixing in repair Fancy type bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply & fix in repair vitreous china wash hand basin, white, flat back of size 550x400mm (excluding taps, waste chain and plug and porcelain stopper) but including brackets complete all as specified & directed.

Supply & fix in repair angular valve, 15 mm dia, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

Supplied and fixing in repair stop valves (ISI marked), 15mm dia, cast copper alloy,chromium plated fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supply & fix rotational moulded polyethylene water storage tanks 500 liters capacity, (cylindrical, vertical in closed top) ISI marked triple layered hoisted and fixed in position with all fittings all as specified including dismantling existing water tanks complete all as specified & directed.

Supply & fix in repair PVC low level flushing cistern of10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore, suitable for low level cistern complete all as specified & directed.

Cutting chase, pining in making good to facings where required and pointing in cement mortar (1:3) to ends, cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth complete all as specified & directed.

Supply & fixing 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed and including taking down old pipe complete all as specified & directed.

Supply, fixing and testing 20 mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including taking down old pipe complete all as specified & directed

Supply & fix PVC ball valves, high pressure with polyethylene float and fly nut complete screwed for iron pipe 20mm bore complete all as specified & directed.

Supply & fix in repair vitreous china squatting pan of ‘Orrisa pattern’ size 580x440mm, white with, integral foot rest including replacement of ‘P’ or ‘S’ trap, lime concrete bedding and making good floor complete all as specified and directed.

Supply & fixing in repair pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply & fix in repairs chromium plated shower roses with swivel joints of 75mm size complete all as specified & directed.

Supplied and fixing in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S & F in repair corner glass shelf with bracket fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified & directed.

Demoliton & breaking up 100 mm dia drain pipes (Salt glazd work, AC or re-inforced concerete) complete all as specified & directed.

S&F in repair Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified & directed.

Supply & fixing grating doom 100 mm dia of PTMT complete all as specified & directed.

M& L for Preparing newly plaster surface & applying one Coat of Cement Primer of any colour over and including two coats of cement base paint complete all as specified & directed.

M&L for moorum filling including spreading levelling, watering and well ramming in layer not exc 15cm thick complete all as specified & directed.

M & L for rendering 15mm thick in CM 1:6 on fair faces of brick work ,concrete surface of wall and finished surface even and smooth without using extra cement and mixed with water proofing compound @3% by weight of cement complete all as specified and as directed. Note: WPC shall be measured and paid separately.

Supply only integral water proofing compound ISI marked complete all as specified and as directed.

Material and labour for 10 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M & L for preparation of new plastered surface of wall and applying two coat of white wash on wall including cornices, pilasters etc complete all as specified and as directed.

Material & labour for hardcore of Broken stone or boulders n.exc. 63mm, deposited spread and leveled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

Supply & fixing 15 mm bore pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe, complete all as specified & directed.

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed

Supply and fixing of PVC (SWR) bends 75mm bore, any radius complete all as specified & directed.

S&F of cast iron floor/Nahani trap with grating 75mm dia including jointing to waste pipe including removing old traps, complete all as specified & directed.

Supply and fixing of PVC SWR vent cowl 110mm bore, complete all as specified & directed.

S&F in repair for 15mm bore dia of pipe Stop valves/angle valve, chromium plated ,cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions with wall flange complete all as specified and directed

S&F Brass chromium plated soap dish round/oval shaped fixed to wall with PVC gutty and CP screws, complete all as specified and as directed.

S&F Brass CP shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F high density 50mm bore polythylene pipes (HDPE) of pressure rating 6Kg/cm2 fixed complete to walls or in florrs with necessary socket, elbow & bend etc complete all as specified and directed.

S&F of PVC waste pipe for WHB 32mm dia 75cm long flexible type of suitable dia complete all as specified and directed

Supply & fixing of PVC connections of 600mm long suitable for 15mm dia iron pipe including 2 nos CP brass check nuts complete all as specified & directed.

Supply & fixing of rotational moulded polyethylene water storage tanks 1000 liters capacity, (cylindrical, vertical in closed top) triple layered ISI marked hoisted and fixed in position with all fittings complete all as specified & directed.

S&F 15mm bore Gun -metal, globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified and directed

S&F Aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed.

M&L for 60mm thick Machine pressed precast interlocking paver block any shape and size M-35 grade conforming to IS 15658-2006 complete all as specified and directed.

Material and Labour for UPVC pipe 150mm dia type "B" with wall thickness 4mm(min) of pressure rating 8 KN/sqm laid in trenches and jointed with cement solvent including testing complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, Bracke sketch fitting, ceiling roses, lamp holders, brackets, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. Note:- The damaged surfaces to be made good with plastering (1:6). & finish the surface to matching with existing surfaces as directed by Engineer-in-charge. Cost of the same deem to be included in quoted rates and nothing extra on this account admissible.

M&L Point wiring with 1.5 Sq. mm (nominal area) FRLS PVC insulated and unsheathed multistranded copper conductor cable 1100 Volts grade drawn through and incl PVC rigid concealed conduit (ISI Marked) suitable size with all accessories having thickness not less than 1.8mm incl sheet steel/ CI terminal box of adequate size having thickness not less than 2mm including 3mm thick hylem/masonite sheet including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor multistranded cable of green colour as earth conductor connected to common earth dolly complete all as specified and directed for one light / fan point controlled by one switch complete all as specified and directed. Note: 1. Connections of cable with MCBs/Switch Sockets shall be done through proper size copper/brass thimbles. 2. Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit in not feasible. 3. Proper colour code will be used for wiring as per the electrical rule and as directed.

All as per Srl item No 173.00 here-in-before but for one 5 pin 5 Amp socket outlet point on inependent board controlled by one switch complete all as specified and directed

All as per Srl item No 173.00 here-in-before but for one 5 pin 5 Amp socket outlet point on same board controlled by one switch complete all as specified and directed

All as per Srl No 173.00 above but for call Bell point complete all as specified and directed by Engineer In Charge

M & L for point wiring with 2.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable with in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained

S & F switch piano flush button single pole one way 5 Amp AC 240 volts, all as specified and as directed.

S & F Bell push flush type 5 Amp 240 volts complete all as specified and directed

S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 3 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

M & L for ceiling rose, PVC/Polycarbonate, insulated body, surface Bakelite 65mm dia three terminals all as specified and as directed.

Supply and fixing of ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S & F Bell AC,230 Volts, Single pole complete all as specified and directed

S&F in replacement mirror light 10 Watt LED 2' length prewired with all accessories including lamp and connected electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor 3core cable of size 0.50Sqmm complete all as specified and directed. Make :- WIPRO CAT PART No. D531065 or equivalent in any make mentioned in list of product.

S & F LED Bulb , B22 type ,14 watt White,complete all as specified and directed.

S&F 20W surface / wall mounted batten LED luminair, extruded aluminium housing with PC diffuser and ind electronic driver with high efficiency long life, CRI = 80 (Minimum), PF > 0.95, luminous efficacy > 100 lumens/Watt operating voltage 140V-240V, CCT (K) > 6500, THD < 10% complete including 20W LED tube rod with all accessories internally prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed.

S&F in replacement Energy saving, surface mounted, bulk head LED luminaire 10 W with PDC aluminium housing and polycarbonate diffuser with IP 66 protection complete including connecting up with three core twisted flexible copper conductor cable of suitable size.complete all as specified and directed. Make :- CROMPTON CAT Part No. LBHP-10-CDL or equivalent in any make mentioned in list of product.

Taking down ceiling fan by disconnecting the electric connection and dismantling the blades and removing from ceiling/roof of bldg by descrewing the nut, bolt etc complete all as specified and directed.(Note-Old u/s balance ceiling fans will be deposited in Store yard of AGE E/M)

Rehanging only of ceiling fan and connecting up including provision of PVC insulated and overall sheathed flexible copper conductor cable 3 core of size 0.50Sqmm from ceiling rose or connector to fan including minor repairs such as replacement of locking pin, reel insulators, bolts, nuts etc and spraying one coat of synthetic enamel paint of required colour all as required and directed by Engr-in-charge.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and supply and fixing MS ventilating fans Single phase, 230 volts 300 mm or 12” H.D EX Fan (900 RPM) complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

S & F of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F MCB SP 240V, 50Hz, 10 KA, 'B' curve of rating 6 to 40 Amp all as specified and directed.

S&F MCB SPN 240V, 50Hz, 10 KA, 'B' curve of rating 6-40 Amp all as specified and directed.

M&L for sub Main Wiring with 2 run of 6 Sqmm FRLS PVC insulated and unsheathed, multistarnded copper conductor cable using colour code for phase red and neutral black with and including 6 Sqmm FRLS PVC insulated and unsheathed multistranded copper conductor cable in green colour as earth conductor connected to common earth dolly, drawn in and including concealed PVC rigid conduit of suitable size having thickness not less than 1.8mm (ISI marked) with and including all accessories complete and making good to disturbed surface of wall/floor with cement mortar and finishes to match existing surface including taking down of existing unserviceable surface/concealed sub main wiring any type complete all as specified and directed. Note: Two run of submain wire (phase and neutral), and one run of earth including PVC conduit and accessories will be measured as one run.

S&F distridution board iron clad vertical DB double door with IP-43 protection and mechanical strength as IK-09 suitable for MCCB as incomer an MCB as outgoing 415V 3Phase 50Hz 4 Way complete with appropriate size of copper bus bar and neutral link complete with one MCCB 3Pole 415V 63Amps rating,16kA with adjustible thermal and adjustible magnetic release of the same make as of distribution board complete all as specified and directed. Note: (MCBs will be measured and paid saperately)

S & F bldg secuirty light fitting energy saving high efficiency LED street light fitting 30 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI pipe light grade bracket of size 32 mm dia bent to shape having length not less than 1.5 mtr fixing with clamp 2 nos made of FI 40x6mm with nuts and bolts etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage. Make: CROMPTON CAT REF. LSTS-30-CDL or equivalent in any make mentioned in list of product.

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (Earth pit not less than 2.25 metre deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts,check nuts and washers of galvanised iron or steel all as showin in electrical plate No.3 of SSR Part-I (2009) including filling of 15cm thick layer of charcoal dust, common salt all around Earth plate, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40 mm thick pit cover RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregrate reinforced with suitable handle and angle iron frame made out of angle size 40x40x6mm and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including test on completion. (Note :- The rate quoted include cost of min 7.5 metre earthing wire)

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable punned down to 18cm complete all as specified and directed. Note:- Punned thickness 18cm shall be considered for payment.

M&L for Brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class 'B' bricks laid complete all as specified and directed.

Supply, laying & testing of XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 16 Sqmm 4 core complete all as specified and directed. Note:- Earth work including excavation, returning filling , removing, sand cushioning, GI pipe, brick covering for mechanical protection of cable etc will be measured and paid separately under respective items of schedule.

Supply and fixing of GI tubing medium grade of 40 mm nominal bore of pipe in trenches/under roads/ under culverts/under paths/under floor/on walls /with pole in new position with screwed sockets joints, together with all tube fittings (such as bends, elbow, tees, short places connections back nuts, diminishing places, caps, plugs and union etc) complete all as specified and directed .

S&F Storage type Electric water heater (Geyser) capacity 25 litrs BEE 5 Star rating with complete accesoiries complete all as specified and directed.

S&F stop valves, fancy type, CP, cast copper alloy, with long shank cup (concealed type) screwed down, high pressure with crutcher butterfly handle, screwed both ends for 15mm bore dia of pipe complete all as specified and directed.

S& F Bib taps, fancy type, cast copper alloy, screwed down high pressure with crutch of butter fly handle, screwed for 15mm dia pipe complete all as specified and directed.

S&F PVC connection for hot & cold water 15mm dia 450 mm long with brass adaptors complete all as specified and directed.

Notes :- (a) The contract sum shall be arrived at after deduction of amount of Schedule of Credit. (Rs. 39,690.50). (b) PERFORMANCE SECURITY :- (Refer condition 19 of IAFW-2249) The performance security for an amount equivalent to 3% (Three percent) of the accepted contract sum shall be delivered by the successful bidder immediately after the date of intimation letter of acceptance and all provisions shall be applicable as per condition 19 of IAFW 2249.

kay gee construction co

RD Engineers

M/s. G M Builders & Contractors

VIKRAM SINGH MANHAS

M/S SEVENUP

M/S S KUMAR & CO