SPECIAL REPAIRS TO BUILDING NO T-101 (OTM) UNDER GE (NORTH) BANGALORE

Amount

Dismantling of Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings including ridges etc complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed

Dismantling timber scantlings 40 sq. cm and over in section, in any position as in Framed work etc complete all as specified and as directed

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slab s/blankets, any thickness, including cover fillets etc complete all as specified and as directed

Demolition of brick work /stone masonry/PCC block masonry built in cement mortar of any description all as specified and directed.

Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed

Dismantling of Stone sett paving of any description or thickness or thickness in floors, aprons etc (Laid bedded and pointed in any cement mortar) incl removing off the premises etc complete all as specified and as directed

Taking down cement plaster of any description hacking for key or raking out joint on old brick work/stone/concrete surface etc complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but not exc 4 Sqm each, including cutting holes for removing the hold fast etc (Disturbed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc (Disturbed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified and as directed

Supply and fixing of Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to IS Fe-410-W(Gde-E-250) quality- B etc complete all as specified and as directed

Fixing only Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates incl welding/riveting/nut & bolts etc complete all as specified and as directed

Supply and fixing of Hollow steel section for structural use in beams, col, rafter purlins or other connecting plates incl necessary welding, riveting, nut bolts as per IS-4923 etc complete all as specified and as directed

Supply and fixing of Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws etc complete all as specified and as directed

Supply and fixing of Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed

Supply and fixing of False ceiling with grid suspended system of size 600X600mm standard section consisting of main runner GI main tee and cross as per manufacturer instructions /catalogue GI main tee and cross as per manufacturers instructions and ceiling suspended with 3 mm dia GI wire hanger fixed with steel dash fastener, butter fly clips, hold down clips etc (Main corner, cross tee& wall angle of MS galvanized with PPPCGS) incl 4 mm thick HPSC self textured design pre primed non asbestos fiber cement building boards fixed to false ceiling including taking fown old existing ceiling of any description complete etc all specified and as directed.

Material and Labour for 75 mm thick cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in sub base of flooring etc complete all as specified and as directed

Material and Labour for 25 mm thick Cement concrete type B-1,1:2:4 (20mm graded aggregate) as in leveling course of flooring etc complete all as specified and as directed

Material and Labour for screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed.

Material and Labour for matt finished Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed

Material and Labour for rendering 10 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface as backing coat of dado/skirting etc complete all as specified and as directed

All as per item No 1.21, above but as in skirting

Material and Labour for 75 mm thick Cement Concrete Type C-1, 1:3:6 (with using 20 mm graded stone aggregates) as in plinth protection etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade "A" complete all as specified and directed.

Material and Labour for exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. complete all as specified and as directed

Material and Labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

Material and Labour for machine pressed pre-cast concrete interlocking coloured paving Block of glass fibre reinforced glossy finished vibro compacted any shape and size confirming to IS-15658-2006 of 60 mm thick, M-35 grade to match with grey cement and pigment etc complete all as specified and as directed

Material and Labour for Pre-cast cement type C1 1:3:6 (with using 20 mm graded stone aggregates) concrete block masonry withsolid blocks, exc. 10 cm in width and setting CM 1:6 etc complete all as specified and and as directed

Material and Labour for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings, Chajja kerbs etc including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed .

Material and Labour for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) etc complete all as specified and as directed

Material and Labour for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directedNotes : WPC shall be measured and paid separately

Supply only liquid water proofing compound

Supply and fixing of 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one or more rebate including necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

Supply and fixing of Box type Steel Windows/Ventilators double side shutters (Windows side hung type , Ventilators top hung) pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm , windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc complete all as specified incl 12mm square guard bars/grill welded with steel frame (100mmc/c horizontally) all as specified and directed by Engineer-in-Charge. NOTE: (i) Payment under this item will be make combined for steel frames, steel shutters and Guard bar/Grill, However unit rate quoted shall deemed to include cost of beading, fittings such as handles, hinges, Telescopic stays, locking arrangements and fixing of glass and wire mesh etc. (ii) 4 mm thick sheet glass and 0.36 mm dia stainless steel wire mesh be measured and paid separately. (iii) Weight of Grill/Guard Bars, handle, hinges and locking arrangements shall not be accounted for payment purpose.(Note : All Windows/Vent design as per CECZ TD drg No 539)

Material and Labour for cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) as in hold fast and filling of pressed steel chowkat etc complete all as specified and as directed

Supply and fixing of 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed

Material and Labour for Hollow steel section for structural as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to IS-4923 etc complete all as specified and as directed

Supply and fixing of in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed '

Supply and fixing of Sheet glass 4mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane and all as specified.

Supply and fixing of Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

Supply and fixing of aluminium alloy, anodized sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

Supply and fixing of 150 mm long aluminium handle, cast type, anodized etc complete all as specified and as directed

Supply and fixing of 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed.

Supply and fixing of 300mm, brass ordinary rat tail rod pattern springs including roller and roller plate complete etc complete all as specified and as directed

Supply and fixing of in repairs stainless steel decorative curtain rod of 25 mm bore with wood finishes (weight not less 400 gms per running meter) incl fancy finale caps cap (02 nos in each curtain rod) etc complete all as specified and as directed

Supply and fixing of in repair Brass Chromium Plated Bracket for curtain rod of dia 25 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed .

Complete removal of existing treatment by means of wire brushing, sand paper, manually or mechanically up to visible of plastered surface incl rubbing and washing etc complete all as specified and as directed

Material and Labour for 2mm thick wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc complete all as specified and as directed

Material and Labour for Preparing new plastered surface of walls and applying two coats distemper oil emulsion, white or tinted over a coat of alkali resistance primer complete all as specified and as directed

All as per item No 1.49 above, but on old Plastered surface of wall complete all as specified and as directed.

Material and Labour for preparing newel plastered surface of wall and applying two coat of cement base paint over a coat of alkali resistance primer etc complete all as specified and as directed

All as per Item no 1.51 above but on Old Plastered surface of wall complete all as specified and as directed.

Material and Labour for Preparation of new or previously untreated steel iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of exc 1.0 Km but not exc 1.50Km , beyond the lead included in the rates, including loading, unloading and stacking at the destination etc complete all as specified and as directed .

Taking down carefully aluminium/ copper wiring/power point wiring (light, fan, socket or power) complete including fittings such as switches ceiling roses, pendants, regulators, sockets light fittings, fans etc and making good the disturbed surface of walls, ceiling etc including painting with same colour of the back ground complete all as specified and as directed by Engineer-in-Charge.

Wiring complete with 1.5 Sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non-metallic rigid PVC conduit including accessories , surface mounted / concealed type run on walls/ ceiling including MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 1.5 Sqmm PVC insulated single core multi stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed. (a) One light point controlled by one switch

(b) One fan/Exhaust fan point controlled by one switch/regulator

(c) One 3 pin socket out let 5 A on independent board same board

(d)One 3 pin socket out let 5 A on same board

Wiring complete with 2.50 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non-metallic rigid PVC conduit including accessories concealed type, run on walls/ ceiling incl MS terminal boxes fabricated with 1.6 mm thick MS sheet surface mounted/ concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 2.50 Sqmm FRLS PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed. Note for Item No 2.02 to 2.05 :-(i) The earth wire for the points in the same circuit can be looped from point to point.(ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring(iv) Cost of a circuit of any length of cable from DB to any switch /socket board to be included in point wiring.(v) Cost of cutting chase for conduits and making good to wall in case of recessed or concealed conduit wiring is included in point wiring rate.

Material and Labour for groove cutting in wall/ floor and making good of disturbed wall / floor, painting of existing colour all as specified and as directed by Eng-in-charge .

Removing of old existing and provision of new Sub main wiring complete with two runs of 2.50 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with one run of 2.50sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through existing non metallic rigid PVC conduit and conduit accessories incl removing of the existing sub main wiring all specified and as directed. Note: 3 runs of cable will be measured as unit length.

Supply and Fixing of wall mounted LED batten, suitable for indoor applications 1x20 watts,4 feet with extruded aluminium housing & integrated LED channel complete with three core flexible copper conductor accessories all as specified and as directed. Make: Bajaj Cat part No BCLAB 20WH LED P or Equivalent Makes in specified in P.S

Supply and Fixing of Modular switch 1 way 6A, 1 module all as specified and as directed .

Supply and Fixing of Modular switch 1 way 16A, 1 module all as specified and as directed .

Supply and Fixing of Modular Socket 6A-2/3 pin, combined 2 module all as specified and as directed.

Supply and Fixing of Modular Socket 6A/16A-2/3 pin, combined 2 module all as specified and as directed.

Supply and Fixing of Modular type fan step regulator, 120W-2 module all as specified and as directed.

Supply and Fixing in replacement ceiling rose, surface Bakelite type 65x50mm, 2 to 3 terminals all as specified and as directed

Supply and Fixing of MCB SPN 240 volts 32 Amps complete all as specified and as directed

Supply and Fixing of MCB single pole 240 volts 10 to 32 Amps complete all as specified and as directed

Supply and Fixing of MCB DB SPN 8 Way double door type 240 Volt with 200 Amps rated Bus Bar including necessary dummy plate.

Supply and Fixing of 30W LED bldg security light fitting with pressure die cast housing along with prismatic polycarbonate diffuser with IP 66 protection. Make:- Bajaj, Cat No.:- ENXT P 30L WH SY PC SD or Equivalent Makes in specified in P.S

Supply and Fixing of Bracket made out of GI tubing medium grade 25 mm bore, approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm, nuts, bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed.

Taking down unserviceable /old vintage ceiling fan , cable end, dismantling blades and removing fan and blades to MES Store.

Dismantling /opening the ceiling fan of 1200mm sweep of any make and type ,removing the old defective winding carefully, cleaning the inner parts and rewinding with the same gauge super enameled copper conductor of good insulation ,varnishing ,drying and reassembling complete all as specified and as directed.

Supply and Fixing of ceiling fans with complete accessories, 230V, SP 1200 mm Sweep with BEE 3 Star rating complete with all accessories and fixing the fan from ceiling rose with 3 core flexible copper wire 24/0.20 sqmm, etc all as specified and as directed. Make Bajaj, SABSE TEZZ EE 03. Model No 251120 or Equivalent Makes in specified in P.S.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to and including galvanized iron wire of 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles, check nuts and washer etc made of galvanized iron connected to earthing test point through protection pipe light grade of 20 mm dia all as shown in electrical plate No 3 of SSR Part - I 2009 and as specified or indicated and testing on completion including earth work and excavation in any type of soil plain cement concrete (1:3:6) type C1 chamber, per cost slab 40mm thick in cement concrete (1:2:4) type B 1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways including funnel with watering pipe of 20 mm dia medium grade ,wire mesh and lugs, including test point including cable connected with suitable size copper lugs complete all as specified and as directed.

EMPEROR ARCHITECT

S S CONSTRUCTIONS

B5BUILDING SOLUTIONS