Special Repair of H.P. PCB Building Parwanoo, Sector-IV Parwanoo, District Solan

Amount

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required i/c carriage of material in all leads & lifts. Approved make brand of TISCO/ SAIL/OSWAL.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete i/c carriage of material in all leads & lifts.Approved make brand of TISCO/ SAIL/OSWAL.

Ridges plain (500 - 600mm)

valleys .

Providing and fixing of 40 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts, G.l. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1 cement : 3 coarse sand). i/c carriage of material in all leads & lifts1.00 mm thick with zinc coating not less than 275 gm/m².

Providing and fixing 15 cm wide, 45 cm overall semicircular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete i/c carriage of material in all leads & lifts. 0.63 mm thick with zinc coating not less than 275 gm/m². Approved make of TISCO/SAIL/OSWAL.

Providing and fixing M.S. BP Sheet 1.66mm to 2.0mm thick in eaves board /facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of material in all leads & lifts.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, i/c carriage of material in all leads & lifts. (i) Single socketed pipes..(a)110mm dia pipes. Approved make of Finolex/ D- Plast/ Supreme

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion i/c carriage of material in all leads & lifts. Approved make of Finolex/ D- Plast/ Supreme

Bend 87.5° 110mm dia.

Shoe (Plain) 110 mm dia.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete i/c carriage of material in all leads & lifts. 110mm dia. Approved make of Finolex/ D- Plast/ Supreme

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete i/c carriage of material in all leads & lifts. Appoved brand of TISCO / SAIL (Rastriya Isat Nigam Limited) conforming to BIS Specifications.

(i) In trusses and trussed purlins in building.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture i/c carriage of material in all leads & lifts. Approved make of TISCO/SAIL/RNIL.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete i/c carriage of material in all leads & lifts.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade . New work (two or more coats) over and including water thinnable priming coat with cement primer i/c carriage of material in all leads & lifts. Approved brand of Asian/ Nerolac/ Berger

On walls

On ceiling

Finishing walls with Acrylic Smooth exterior paint of required shade .New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) i/c carriage of material in all leads & lifts. Approved brand of Asian / ICI Dulex)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete surface i/c carriage of material in all leads & lifts. Approved make of BIRLA/ JK/ SAKARANI

Repairs to plaster of thickness 12 mm to 20 mm in atches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping round, all complete as per direction of Engineer-in- Charge lifts.With cement mortar 1:4 fine sand . i/c carriage of material in all leads &

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) i/c carriage of material in all leads & lifts.

20 mm cement plaster of mix in CM 1:6 (1 cement :6 fine sand) i/c carriage of material i/c carriage of material in all leads & lifts.

15 mm cement plaster on rough side of single or half brick wall of mix.f mix in CM 1:6 (1 cement :6 fine sand) i/c carriage of material in all leads & lifts.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture i/c carriage of material in all leads & lifts.Approved make of Asian/Nerolac/ICI Dulex/ Berger.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture i/c carriage of material in all leads & lifts. ( Approved make of Asian/ Nerolac/ICI Dulex /Berger.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) i/c carriage of material in all leads & lifts. ( Approved make of Hindalco/ Jindal

Powder coated aluminium (minimum thickness of powder coating 50 micron

For shutters of doors windows &ventilatorsincluding providing and fixing hinges/pivots and making provisions for fixing of fittings powder coated aluminum.

Providing and fixing aluminium shutter work for doors, windows 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.Pre-laminated particle board with decorative lamination on both sides i/c carriage of material in all leads & lifts. ( Approved make of Hindalco/ Jindal.

Providing and fixing white vitreous china pedestal typewater closet (European type W.C. pan) with seat and lid,10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required i/c carriage of material in all leads & lifts. W.C. pan with ISI marked white solid plastic seat and lid. Hindware or CeaMake

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittingsand brackets, cutting and making good the walls wherever require i/c carriage of material in all leads & lifts. White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. (Hindware or Cera/ Make)

Providing and fixing C.P Grating 100 mm dia including carriage of materials in all leads & lifts (Ess-Ess/ Nova Czar/ Jaguar)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 i/c carriage of material in all leads & lifts . 15 mm nominal bore (Ess-Ess/ Nova Czar/ Jaguar).

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 i/c carriage of material in all leads & lifts. (a) 15 mm dia. (Ess-Ess/ Nova Czar/ Jaguar).

Providing and fixing uplasticised PVC connection pipewith brass unions i/c carriage of material in all leads & lifts.(a) 15mm dia 45 cm. length.

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately) i/c carriage of material in all leads & lifts.

Suraj Thakur

SD CONSTRUCTION