SPL REPAIR TO TOILET OF BLDG NO P-56 AND P-58 (AGAINST JOB NO. 81 SA/BTD/SR(BLDG)-16/2024-25) UNDER GE(N) BATHINDA AT BATHINDA MIL STN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed by Engineer-in-charge.

Material and Labour for glazed ceramic coloured tiles 7.5 mm to 8.5 mm thick , 300mm x 600mm size in verticle surface including 10mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured epoxy grout to match the shade of tile including necessary cutting as per site requirement etc complete all as specified and as directed by Engineer-in-charge.

Material and Labour Non Skid coloured ceramic tiles 6mm to 7mm thick (square/rectangular) of Size minimum 600mm x 600mm, in floors etc including 10 mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured epoxy grout to match the shade of tile including necessary cutting as per site requirement having scratch hardness of surface min 6 on Mohs Scall and abrasion resistance of class V complete all as specified and as directed by Engineer-in-charge.

Demolition of cement concrete un- reinforced of any description and in any position not otherwise specifically provided for and including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance exceeding 500 metres and not exceeding 1.5 Kilometre away from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Waterproofing treatment to sunken floor using acrylic based multipurpose polymer. The treatment shall be carried out as per manufactures specification. The treatment shall be carried out in the following stages: 1. Surface preparation of substrate by removing all traces of contaminates, loose and friable particles, cement laitance oils and grease, water repellent coatings etc 2. Injection grouting using cementitious grout if required. The payment for injection grouting shall be made separately etc. 3. Repair to the substrate, filling of blow holes/voids and surface leveling using appropriate products specified by the manufacture. 4. All intersections of horizontal and vertical surface should be profiled with a mortar fillet of minimum 25mm x 25mm. 5. The moisture content of the substrate shall be checked before application of first coat at water proof coating at the rate of 200 g/m2 followed brush topping at 450g/m2 per mm. The second coat shall be reinforced with glass fabric between the first and second coat. 6. The treatment shall be protected by application of polymer modified cement mortar of thickness 10mm applied at the rate of 50g per mm. 7. Tech specification : Tensile adhesion strength 0.5N/Sqmm (as bonding slurry).

Material and labour for Aerated Autoclaved Concrete (AAC) blocks work according to Indian Standard specification IS:2185(Part-3)-1984 and latest revision built in Cement and sand mortar 1:6 with Aerated Autoclaved Concrete (AAC) blocks straight or curver on plan exceeding 6mtr Mean radius as in sunken floor complete all as specified and and as directed by Engineer-in-charge.

Material and labour for 25 mm thick cement concrete (1:2:4), type B-I using 20 mm graded stone aggregate as in floor for leveling course complete all as specified and as directed by Engineer-in-charge.

Demolition of RCC of any description and any position not otherwise specially provided and including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance exceeding 500 metres and not exceeding 1.5 Kilometre away from the site complete all as specified and as directed by Engineer-in-Charge..Note:The weight of scrap iron for schedule of credit shall be ascertain by BOO as ordered by GE.The copy of BOO duly countersinged by GE shall be enclosed with final Bill.

Material and Labour for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) on rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia including making of rungs, handles etc complete all as specified and as directed by Engineer-in-charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour 18-20mm thick machine cut, granite duly factory grinding and polished (table rubbed and polished) of approved colour for counter sunk wash basin, plateform/cooking plateform or as directed, including screed bed 15mm thick in cement mortar (1:4) (grey cement slurry) including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of granite stone slab including cutting as required including cleaning and extra polishing if required complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and as directed by Engineer-in- charge.

Material and Labour Brick work with sub class ‘B’ burnt clay old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in- charge.

Material and labour for Brick work with sub class ‘B’ burnt clay old size bricks, straight or curved on plan to any radius in half brick walls built in Cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance exceeding 500 metres and not exceeding 1.5 Kilometre away from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15mm thick Rendering in Cement mortar 1:6 on faire face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Blank.

Supply and fixing GI powder coated frame work 605mm x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and duly suspended with 4mm GI wire hangers (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made of GI flat 40mm x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including providing 600mm x 600mm x 10mm-12mm thick ceiling mineral fibre board in grid fixed in false ceiling grid including taking down old ceiling with cover fillets as per above specifications complete all as specified and as dirercted by Engineer-in-charge.Note: The rate of ceiling mineral fibre board size 600mm x 600mm x 10mm-12mm thick is included in this item and nothing shall be paid extra on this account. Note: Old unservicable material shall be deposited in th yard of concerned AGE B/R of GE (N) Bathinda.

Supply and fixing hollow PVC Lining consisting 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on with and including PVC frame complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters of PVC door , wooden door shutter, wooden window shutter , Mild steel window and Mild steel ventilators (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters of PVC door ,wooden door shutter, wooden window shutter , Mild steel window and Mild steel ventilators (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 Sqm each complete all as specified and as directed by Engineer-in- charge.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.,as per manufacturer's instructions and as directed by Engineer-in-charge.

Supply and fixing 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge.

Supply and Fixing type 3 stainless steel door handle of size 125 mm conforming to IS 208-2020, fixed with countersunk conforming to IS 208-2020 complete all as specified and as directed by Engineer-in-charge.

Supply and fixing stainless steel barrel tower bolts, 200 mm long conforming to IS 15833-2009, with bright bolts and fixed complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 250mm long stainless steel sliding door bolts confoming to IS 15834-2008 , plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed length of bolt complete all as specified and as directed by Engineer-in- charge.

Supply and fixing 100mm long stainless steel butt hinges with stainless steel screws complete all as specified & directed by Engineer-in-charge.

Supply & fixing aluminium (Extruded section body) body door closer hydraulically regulated, designation No 3, universal type suitable for door shutter of 851 to 1000mm in width and weight between 61 to 80 Kg, ISI marked complete all as specified & directed by Engineer-in-charge.

Material and labour Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixedcomplete all as specified and as directed by Engineer-in-charge..

Supply and fixing in repair Mortice lock 4 levers , vertical type, size 100 mm alumunium , etc complete all as specified and directed by Engineer-in-Charge.Note: Old unservicable material shall be deposited in th yard of concerned AGE B/R of GE (N) Bathinda.

Material and labour for Providing and fixing aluminium work with Polyester powder coated aluminium ( minimum thickness of polyester powder coating 50 micron for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conformikng to IS:733 and IS :1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions i.e at top , bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth , rust free, straight, mitred and jointed mechanically wherever required including aluminium cleat angle, aluminium snap beading for glazing/ paneling , C.P. brass/ stainless steel screws, all complete all as specified and directed by Engineer-in-charge . Note :- (i) Weight of aluminium sections , aluminium cleat angles , aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading shall be physically ascertained through a board of officers convened by GE and payment shall be made only after ascertaining the actual weight of aluminium at site. (ii) The rate of material and labour for providing the EPDM rubber, neoprene gasket , C.P. brass / stainless steel screws are included in this item and nothing shall be paid extra on this account. (iii) During considering the weight of aluminium sections , aluminium cleat angles , aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading , the weight of EPDM rubber, neoprene gasket , C.P. brass/ stainless steel screws shall not be considered for measurments and payments. Only the weight of the aluminium sections , aluminium cleat angles, aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading shall be considered and measurment and payment shall be made accourdingly. (iv) During the weight of aluminium sections , aluminium cleat angles , aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading ,the weight of polyester powder coating 50 micron shall not be considered for weight but the rate of material and labour for providing polyester powder coating 50 micron is included in this item and nothing shall be paid extra on this account. (v) Glazing /Paneling and wire mesh shall be measured and paid seperately. (v)The board shall be duly countersigned by GE shall enclosed with Final Bill .

Material and labour 4mm thick aluminium composite panel of polyethylene core 0.5mm skin thick each face any colour as directed, fixing as per manufacturer instruction complete all as specified and directed by Eng-in-Charge.

Supply & fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tack or galvanised wire staples complete all as specified & directed by Engineer-in- charge.

Supply & fixing 75mm x 75mm x 6mm thick polyester powder coated with 50 micron aluminium grill fixed with all necessary accessories ie. Channel, screws etc fixing as per manufacturer instruction complete all as specified and directed by Eng-in-Charge.

Supply & fixing Toughned glass superior quality of 12mm thick high quality glass frosted type including itching on glass door as approved by Garrison Engineer for use in as door shutter, partition, Urinal partitions, and like complete all as specified and directed by Engineer-in-charge.

Supply & fixing stainless steel glass door handle "H" handle of size 300mm long including accessories complete all as specified and directed by Engr- In-Charge.

Supply and Fixing 20 mm bore CPVC pipe SDR 11and plain CPVC SDR 11 fitting with all fitting and fixed to walls & ceilings or laid in floors, including taking down unservicable existing GI tubing of 20mm bore and fittings complete complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 16 mm bore CPVC pipe SDR 11and plain CPVC SDR 11 fitting with all fitting and fixed to walls & ceilings or laid in floors, including taking down unservicable existing GI tubing of 15mm bore and fittings complete complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in repairs vitreous china wash down water closet pan (pedestal pattern, EWC) white clour including connection to drain and to flushing pipe anti syphonage etc., including plastic water closet seat with cover (white or black colour) closed pattern with flat bottom complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair vitreous china wash hand basin oval type under counter, white colour, of size 410mm x 310mm x 220mm excluding taps, but including fancy type 32mm waste coupling and waste pipe, fixing/counter sunked in granite slab, complete all as specified and as directed by Engineer-in-Charge. Note :- Granite slab shall be measured and paid separately under appropriate item of BOQ.

Material and Labour in repairs vitreous china urinal of size 410mm x 380mm x 950mm, half stall type white, with grating and union for discharge pipe including CP urinal spreader and CP connection and waste pipe complete all as specified and Engineer-in-Charge.Note: Flushing cistern and flush pipe shall be measured and paid seperately under appropriate item of Schedule 'A' BoQ.

Supply and fixing in replacement 15mm bore stop cock /angle valve cast copper alloy, chromium plated fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends suitable for iron pipe complete, all as specified & directed by Engineer-in-charge.

Supply & fixing in repair 600 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply and fixing in replacement 15mm bore Stop valves,fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedfor iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

Supply and fixing in repairs Brass chromium plated Tubular towel rail, 20mm dia , D type, 60 cm long between flanges complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing in repair 15mm bore, brass Chromium Plated central hole basin mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement 15mm bore Bib tap long body cast copper alloy, chromium plated , with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

Supply and fixing in replacement 15mm bore 2 way Bib tap cast copper alloy, chromium plated , with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

Supply and Fixing in replacement health faucet chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube and wall hook including making connections and fixed in position complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair stainless steel, Chromium plated, decorative type, soap dish holder of approximate size 160mm x 160mm x 90 mm fixed to wall with rubber plugs complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs toilet paper holder with flat recessed type stainless steel complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing Brass chromium plated bottle traps for wash basins with inlet and outlet including necessary packing, union and cap and fixed complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing Chromium Plated brass fancy type Corner glass shelf (25cm/30cm) with CP brass bracket & railing etc; complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard & railing 60 cm long, complete all as specified and directed by Engineer-in-charge.

Supply and fixing 10mm thick superior quality frosted toughened glass for urinal partition size 600mmx1200mm fixed with SS brackets on walls, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair table top / couner top vitreous china one piece wash hand basin size 700mm x 460mm x 200mm including accessories approved by Garrison Engineer complete all as specified and as directed by Engineer-in-charge.

Supply & fixing brass sensor wash basin mixer as approved by Garrision Engineer for mixing hot and cold water screwed down for iron pipe and complete all as specified and directed by Engr-in-charge.

Supply & fixing in repair single piece vitreous chinaware EWC with connected chinaware flushing cistern, seat cover and twin flush fittings fixed as approved by Garrision Engineer complete all as specified and directed by Engr-in-charge.

Supply & fixing in repair SENSOR Urinal with fixing accessories complete set, of size 37cm x 39cm x 61 cm SENSOART built in sensor of pastel as approved by GE complete all as specified and directed by Engr-in-Charge.

Supply & fixing towel rack of 600mm long CP fancy type of standard quality and size complete all as specified and as directed.

Supply & fixing Liquid Soap dispenser with Glass Bottle complete as approved by GE.

Material and Labour for applying acrylic wall care putty on internal surfaces and external surfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and leveling of surfaces in two or more layers) by using ready made acrylic wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed by Engineer-in- Charge. Make of acrylic wall care Putty : AS described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. (ii)The make of acrylic wall care putty shall be as per the recommendation of manufacturer of paint.

Material and Labour for Preparation of internal ceiling surfaces with and including applying 02 coats of interior emulsion paint (shade as approved by GE ) @ 10.00 sq.m / litre / 2 coats by using roller/brush to ceiling surfaces over with and including one coat of interior emulsion primer @ 10.00 sq.m / litre /1 coat as recommended for under coat by manufacturer of interior emulsion by using the brands of interior emulsion paint and interior emulsion primer as described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Material and Labour for Preparation of internal surfaces of walls with and including applying 02 coats of interior emulsion paint (shade as approved by GE ) , @ 10 sq.m/litre/2 coats by using roller to wall surfaces over with and including one coat of interior emulsion primer @ 10 sq.m/litre/1 coat by using roller as recommended for under coat by manufacturer of interior emulsion by using the brands of interior emulsion paint and interior emulsion primer as described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Material and Labour for Preparation of external walls/ RCC surfaces / soffits of chajjas / roof projections / cantilevers / balcony with and including applying 02 coats of exterior emulsion paint (shade as approved by GE) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/ RCC surfaces / soffits of chajjas / roof projections / cantilevers / balcony etc surfaces over with and including one coat of exterior emulsion primer @ 11 sq.m/litre/1 coat by using roller as recommended for under coat by manufacturer of exterior emulsion by using following brands of exterior emulsion paint and exterior emulsion primer as described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Material and labour for 15mm thick Rendering in Cement mortar 1:4 on fair face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and Labour for rendering 10 mm thick in cement mortar 1:3 on concrete surfaces as in ceiling and finishing the surface even & smooth complete all as specified and as directed by Engineer-in- charge.

Blank.

Blank.

Dismantling and disconnecting of existing Cast Iron soil vent pipe taking out from trenches complete all as specified and as directed by Engineer-in-charge. Note: Excavation and earth work shall be measured and paid seperately.

Supply and Fixing 110 mm bore of pipe PVC (SWR) type B ring fitted pipes single socket in any length with Stack clamps as shown in BTD Drg No. 916 sheet 1/4 to 4/4 and BTD-917 sheet 1/1 of stays to wall at a distance of 100-120mm away from walls complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing 110mm bore,PVC SWR Type-B, bends , junction , TEE and Y (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 110 mm dia PVC SWR Type-B, P trap with grating incluing jointing to waste pipe fixed in cement concrete 1:2:4 type B1, using 20mm graded stone aggregates complete complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 110mm dia PVC SWR Type-B, floor trap with grating incluing jointing to waste pipe fixed in cement concrete 1:2:4 type B1, using 20mm graded stone aggregates complete complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing Branch pieces,PVC SWR Type-B, single 110 mm bore, equal or unqual, complete complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 40mm dia PVC SWR Type-B, P trap with grating incluing jointing to waste pipe fixed in cement concrete 1:2:4 type B1, using 20mm graded stone aggregates complete complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, cable , pipes etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed by Engineer-in- charge.

Returning and filling including spreading, leveling watering and well ramming in layers not exceeding 25cm thick in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Removing excavated material (Soils ) exceeding 50m and not exceeding 500m depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed by Engineer-in-Charge.

Supply and laying DWCPE (SN 8) drain pipes 150 mm nominal dia as per IS-16098 (Part-II), laid in trenches on bed including all accessories/ fittings/ jointed ring, jointing and testing complete all as specified and as directed by Engineer-in- charge. Note:- Excavation , earth work, bedding and pedestal / anchorage if required shall be measured and paid separately under appropriate item of BOQ/ Sch 'A'

Material and labour for PCC (1:4:8) type D-2 using 40 mm graded stone aggregates as in concrete bed of drain pipes of 150 mm bore, laid to required slope including packing under and haunching against the sides of pipes after they are laid and tested including form work complete all as specified and as directed by Engineer-in-charge. Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be outer diameter of drain pipes (not of sockets / collar) plus 30cm.

Material & Labour for Providing Precast Cement concrete 1:2:4, Type-B-1, using 20mm graded stone aggregates as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed by Engineer-in- charge. Note: 1.Reinforcement shall be measured and paid separately under appropriate item of Schedule'A' BoQ.2. The rate of form work is included in this item and nothing shall be paid extra on this account.

Supply & fixing in repairs Rotational Moulded Polyethylene water storage tank ISI Marked of capacity 1000 litres (cylindrical vertical, with closed top), hoisted and fixed in position including making inlet and out let connection complete all as specified and as directed by Engineer-in-charge. (Note :- Ball valve and gate valve shall be measured & paid separately under appropriate items of Schedule 'A' BoQ.)

Supply & fixing in repairs Rotational Moulded Polyethylene water storage tank ISI Marked of capacity 500 litres (cylindrical vertical, with closed top), hoisted and fixed in position including making inlet and out let connection complete all as specified and as directed by Engineer-in-charge. (Note :- Ball valve and gate valve shall be measured & paid separately under appropriate items of Schedule 'A' BoQ.)

Supply and Fixing Ball valve high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 20mm-210 gram) complete all as specified and as directed by Engineer-in- charge.

Supply & fixing Gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge.

Material and labour for cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete and sub base in floors etc complete all as specified and as directed by Engineer-in-charge.

Material and labour for 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in flooring, hard standing, plinth protection/path etc. finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour 2nd Hard Wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails/brads or secured with screws, cross sectional area exceeding 6 sqcm and n. exceeding 13 sqcm, complete all as specified and as directed by Engineer-in- charge.

Supply and fixing drawer brass handles, projecting drop ( 50 mm to 65 mm) on screwed plate complete all as specified.

Supply & fixing magnetic catcher of best quality approved by GE as in cupboards etc. to catch & support shutters complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 500mm long stainless steel pull/push MS roller with channel for drawers complete all as specified and directed by Engr In Charge

Material and labour for cement concrete (1:2:4) type B-0, using 12.50 mm graded stone aggregates as in bands, bedding, benching of manholes, coping, surface channel, roof kerbs or mud stops, rounded or chamfered on edges etc including necessary form work complete all as specified and as directed by Engineer-in-charge.

Taking down carefully copper /aluminium point wiring (light, fan, socket or power point ) complete including fitting such as hylem , sheet switches, ceiling rose, pendent holder sockets, regulator except concealed conduit and sunken boxes etc. complete all as specified and directed by Engineer-in-charge. Note:1.The weight of aluminium scrap and copper scrap for schedule of credit shall be ascertain by BOO as ordered by GE.The copy of BOO duly countersinged by GE shall be enclosed with final Bill.(ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface shall be measured and paid seperately under serial item nos. 102.00,103.00,104.00 & 105.00 of BoQ.

Material and Labour for Concealed point wiring for modular type fittings using approved colour coding as per IS (Red, Black and Green for single phase circuits), with 1.5 Sqmm nominal cross sectional area single core PVC insulated, unsheathed 'multi stranded' FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) 20mm bore surface on wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) including modular metal flush box concealied with front & modular cover plate with frame suitable matching colour of required module for mounting or housing switches, socket outlets, fan regulators, etc. including blanking plates & all other fixing accessories for one light/fan/call bell/exhaust fan point controlled by one 5/6 Amps switch and including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and as directed by Engineer-in- charge Note for serial item nos.102.00,103.00,104.00 & 105.00 : The quoted unit rate is deemed to be inclusive of cost of metal flush boxes, modular white cover plates, modular frame plates and flush fixed with cement mortar 1:4 etc.However modular switches & modular sockets shall be measured and paid seperately under respective items of Schedule'A' BoQ. (ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface is included in this item and nothing shall be paid extra on this account.

All as per item No 102.00 here- in -before but for one socket outlet 3 pin, 5/6 Amp 230 volts flush type on same board complete all as specified and as directed by Engineer-in- charge.

All as per item No 102.00 here- in -before but for one socket outlet 3 pin, 5/6 Amp 230 volts flush type on independent board complete all as specified and as directed by Engineer-in- charge.

All as per item No 102.00 here -in- before but for one socket outlet 6 pin, 6/16 Amp 2 in 1 with cable 2.5 sqmm multistranded copper conductor FRLSH cable on the independent board including provn of 2.5 Sqmm PVC insulated copper conductor FRLSH cable continues as earth wire connected to earth dolly complete all as specified and as directed by Engineer-in- charge.

Supply & Fixing Modular switch one way 6A, one module, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular Switch one way 16 Amp 240 Volt, AC ,1 Module , ISI Marked complete all as specified and directed by Engineer-in-charge.

Supply & Fixing modular type Socket outlet , multipurpose, 3 pin, single pole one way, 6 Amp, two module, shutter type ,ISI Marked complete all as specified and as directed by Engineer-in-charge..

Supply and fixing modular Socket 6A/16A-2/3 pin combined,2 module 250 volts AC shuttered type ISI marked, model fantasy complete all as specified and directed by Engineer-in-charge.

Supply and Fixing ceiling rose surface bakelite 20 mm x 50 mm with three terminal complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement new generation energy saving ,wall mounted LED Tube light batten fittings , extruded aluminum heat sink provided for efficient heat dissipation & integrated electronic driver 20 Watt LED duly fitted on pvc square block 5700K (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz., including electric connection connecting with using flexible coopper wire twin core from ceiling rose to connector complete all as specified and directed by Engineer-in-charge. complete all as per manufacturer's instructions and as directed by Engr-in-charge.

Supply and Fixing in replacement LED mirror light fitting 9 / 10 watt , 6000K lineer and compact with decorative grey end caps , polycarbonate body and ribbrd opal diffuser complete fitting with Lamp & all other accessories fitting arrangment complete all as per manufacturer's instructionons and connection with flexible twin core copper cable of size 23/.00076 from ceiling rose to fitting complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing in replacement LED Street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrossion resistant complete with IP 65/66 protection with and including bracket made out with 40mm bore Galvanised Iron Light grade pipe 1.20 mtr length bent to shape with 02 sets of MS clamps made out of minimum 3 mm MS flat iron with suitable bolt and nuts complete with and including connection with copper cable of suitable size from ceiling rose to fitting complete all as manufacturer's instructions ,as specified and as directed by Engineer-in-charge.

Material and labour in replacement Sub main wiring complete with two single core 4 sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH with and including single core 4 sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH for earth wire in existing PVC concealed conduit (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and directed by Engineer-in-charge. Notes:- (a) Three single core 4 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade shall be measured as one length.

Supply and Fixing in replacement Sheet metal enclousers made out of CRCA mild steel sheet not less than 1.2mm thick,, double door, powder coated DB SPN 8 way 240 Volt, 200 Amps rated bus bar, dust and vermin proof, IP-54, suitable for incorporation of MCB's and isolators etc complete all as specified and as directed by Engineer-in- charge.Note: MCB/ Isolators shall be measured and paid seperately under appropriate item of BOQ.

Supply and fixing MCB ‘C’ curve suitable for 230 volts AC supply, 05 to 32 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-charge

Supply and fixing in replacement Single Pole and Neutral enclosure with a two pin and earth plug and socket complete with and including one MCB single pole of capacity 20 Amps,'C' curve,10KA , 240 volts complete all as specified and directed by Engineer-in-Charge.Note: The rate of one MCB single pole of capacity 20 Amps,'C' curve, 10KA, 240 volts is included in this item and nothing shall be paid extra on this account.

Material and Labour for Making holes for 250 mm dia exhaust fan of suitable shape & size into or through brick walls at groung/First/Scond floor including plastering for making good to the original surfaces of any description disturbed including painting /distemper matching with the existing colour. Note : Rates are deems to be including charges of any type of T&P, Insurance of staff deployed at site.

Supply and fixing Modular type Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, sweep 250mm and electrical connection providing twin core round copper conductor cable of suitable size including marking of MES number including fixed in position complete as per manufacturer instruction in wall / window frame all as specified and as directed by Engineer-in-charge.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ.

RINKU BROTHERS (BID ID -3295534)

M/S VERMA BUILDERS & DEVELOPERS (BID ID -3295337)

M/s Verma Construction Company (BID ID -3295563)

Singla Enterprises (BID ID -3300404)