Installation of Solar Light in front of Md Nasir, Bhabesh Roy, Binod Roy house and Rupandighi Madrasa 4 Nos under Jalash Nizamtara GP within Phansidewa development Block under APAS fund 2025 ID APAS-01-027-150-0006 Booth No 27-150 Job19

Supply for fitting of 12 watt & 2200 lumesns All in one solar LED street light Luminaires having polycrystalline solar cell. Details technical apecification given below: A. System Wattage: Should not be more than 12 Watt (+/-5%) B. System Lumen output: should be less than 2200 lumen. C. System Efficacy: Should not be less than 180 lumens/watt. D. battery chemistry: lithium Ferro phosfate(LiFepo4) battery should be used. E. Battry Capacity: >170 Wh. F.Charging Electronics: Itegrated MPPT chargerwith driver. G. Charger Efficiency: > 90% H. Driver Efficiency: > 90% I.Led Burning Hours: Should be > 50000 Hrs. @ L70/. J. IP Rating:IP65 K. Housing: Aluminum Pressure Die Cast./L. front cover: UV stabilized Polycarbonate cover should be used for better light distribution. M.CCT(Color Temperature ):5700k(+/-5% )/ N. CRI:>70(+/-5%) O. luminaire should have in - built PIR sensor./P.charging & discharge LED indicator:Should be privided in luminaire. Q. Input Voltage:12V DC/. R.Adjustable Tilt Angle (Deg.) : Should be 0-15 Deg. adjustable . S.Sollar cell Efficiency : Min. 12%, polycrystalline./T. Operating Temp Range for Light Engine : 0to +35 Deg. C. U. operating Humidity :Up to 95%/V.safety of solar panel Module: IEC 61730-1,2 &IEC 61215 X. Manufacturer should provide LM79 / LM80 reports corresponding to the luminaire / LED chip along with Type Test Certificate. Warranty -3-years warranty against manufacturer defects from date of supply. luminaire Make : Philips BRP710 P LED 22CW MR S1 12V LFP AIO Solar Equip IN or equivalent model.

Supply & Delevary of 80 mm dia. 5 Mtr Lomg GI ( ISI-M) including CI base & plate & 1 Nos Nipple for loop box 1 Nos Earth Stud.

Erection of Single Steel tubular pole of length as given below with/without sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole upto 1.6 Km from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly (a) Upto 9.0 mtr. Size 0.6x0.6x1.70 mts

S/F jacket single arm header assembly 100 mm dia. Top cap of 0.30 mtr long duly welded with 0.5 mtr long 40 mm dia pipe arm brackey detachable type at an angle 110 degree with the pole including painting with 2 coats of synthetic enamel paint over a cost of R.O. Primer as GS.

Painting of Steel Tubular Pole of lengths and no. of coats of paint, asgivenbelowwithreadymixed paint/primerofapprovedmake, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint. (a) Upto 9.0 mtr. long pole. (ii)1st coat of synthetic enamel paint over the primer

Providing CC (6:3:1) muffing 0.3 mtr dia upto the height of 0.3 mtr. above the ground level around the pole base complete with 3 mm thick neatly finished cement plaster all-round after dismantling the unserviceable muffing if necessary

Supply fittings & fixing of Display Board of size 16"x8" in MS plate with display the scheme details and stech in each post at site.

Add @ 18% GST

Add @ 1% L.CESS