Electrical Works

Amount

fo|qr uxjh; forj.k e.My&f}rh;] xkft;kckn ds vUrxZr fo|qr uxjh; forj.k [k.M&”k”Ve] xkft;kckn ds dk;Z{ks= esa 33@11 ds0oh0 fo|qr midsUnz ‘kkyhekj xkMZu ls iksf”kr foosdkuUn ikdZ esa LFkkfir 400 ds0oh0,0 ifjorZd dh vfrHkkfjrk nwj djus gsrq u;k 250 ds0oh0,0 ifjorZd yxkus dk dk;Z fctusl Iyku o”kZ 2020&21 en esa okg~; ,tsUlh ds ek/;e ls djkus gsrqA

Carrige of ST Pole 11 M- 2NOS., Line material, Stay Rod, ACSR Wessel conductor 100 m, Earthing Rod, Cross arms, 11KV Pin Insulator with pin-6Nos. , Disc fitting- 3 Nos., MS Channel ,MS Angle, Clamps, Lead250 sq mm- 40m, etc all complete material etc. from store Center Ghaziabad /Sahibabad /JE store to site of work including loading and unloading at both end.

Carrige of 250 KVA Transformer from store center Ghaziabad/ Sahibabad/JE store to site of work including loading and unloading at both end.

Erection, Grouting & Foundation of Double Pole Structure 8.5 meter long ST pole 11 m including the work of complete H.T. fittings as per RESPO manual and required for proper completion of work.

Installation and grouting of stay set including the work of nozelling etc. as per RESPO manual required for proper completion of work.

Laying sagging stringing, binding and jumpering etc of ACSR Weasel Conductor on the newly erected pole as per RESPO manual and required for proper completion of work.

Making of Pipe Earthing upto Water Level as per RESPO manual and required for proper completion of work.

Construction of plinth of size 2MX2MX2.5M above ground level and one ft. below the ground level of 9”. After excavation of 4” earth, brick ballast shall be provided and rammering will be done properly after that a retaining wall of 9” width by first class brick in ratio 1:4 of cement and sand shall be made. The earth shall be filled upto one ft. below the top of the plinth. After this brick ballast shall be provided upto 6” from the earth level and froper rammering shall be done. One no. jaal of 12mm MS Tor shall be fixed in the hollow of the plinth and one ft. thick RCC in 1:2:4 ratio of cement , sand and stone ballast shall be laid on the of the plinth. The 12mm thick plastering shall be done all around the plinth in ratio 1:4 ratio of cement and sand. The contractor shall be responsible to complete the work as per direction of supervising Engineer. It includes the cost of labour, T&P, carrier etc. required for proper completion of the work

Fabrication of wire mesh Fencing Frames of different size fabricate out of MS angle iron of size 35X35X5mm². Each frame duly welded and fixing with wire mesh of size 25mmX25mmX10SWG hot dipped galvanized within the frame pressed under MS flats of size 40X5mm inside the angle on all four side with help of approx. 20NO Bolts &Nuts of 10mm diameter 45cm legs of frame will be grouted in 1:2:4 cement coarse send and 20mm gauge stone blast in the size of 0.22X0.22X0.45meter, Each will be painted with one coat of red oxide and two coat Aluminum paint of approved mark after proper cleaning. Fixing of wire mess fencing around on plinth of T/F with wire gauge 25X25mm, MS angle 35X35X5 mm with gate.

Providing and fixing of Stone Pad as requireid

Installation of 250 KVA Transformer on existing plinth/MS chair/ with the help of crane.

Making of connection at both side of T/F with conductor & PVC Cable.

Providing and fixing of suspension/ holding Clamp made of MS Flat size 50X6mm suitable for pole as per RESSPO specification

Supplying and fixing of Copper Bus Bar Strip for transformer connections as reqquired.

Providing and fixing of MS bolt & Nuts of size (16X150mm ,4”X1/2” Ench,1.5”X1/2” Ench,1”X1/2” Ench )with 2No Bolts & Nuts size 16X100mm & off size half threaded of good quality.

Providing and fixing of Aluminium Crimmping Lugsf or connection as required.

Om Enterprises

R. P. T. Electrical