REPAIR AND PAINTING OF VARIOUS TYPE OF ALMIRAH STEEL, LOCKERS AND OTHER FURNITURE FOR OTM ACCN AT PANAGARH UNDER GE PANAGARH

Amount

FD-99(M) Board Notice 1200x900

(a) Removing of unsv / broken existing door glass from board notice and S&F new door glass of 4 mm thick of existing shape and size and making functional

(b) Removing of unsv / broken existing door shutter 2 way from board notice and S&F new door shutter of existing shape and size and making functional

(c) Removing of unsv / torn out existing baize green cloth from board notice and S&F baize green cloth of existing shape and size and making functional

(d) Removing of unsv existing soft wood board from board notice and S&F new soft wood board 19 mm thick of existing shape and size and making functional

(e) Removing of unsv existing wooden frame of board notice and S&F new wooden frame made of hard seasoned teak wood of existing shape and size and making functional

(f) Preparation of surface by Remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. .

FD-220 Charpoy GI Pipe with ply top

(a) Remove the existing unserviceable Ply wood from Charpoy GI Pipe and making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

(b) Removing the unserviceable/broken check nuts form GI charpoy & supply and fix 6mm thick GI Medium grade check nuts suitable for 32mm dia GI pipe all as specified and shown on drawings (Each check nut will be measured as single unit)

(c) Removing the unserviceable broken 3 way GI elbow from GI charpoy and S & F 32 mm dia GI medium grade 3 way elbow ISI marked all as specified and shown on drg and directed by Engr-in-Charge (Each GI Elbow shall be measured as single unit)

(d) Removing the existing unserviceable/broken long rail from GI charpoy and S & F new long rail of GI tubing 32mm including cutting, threading and bringing the GI charpoy into the original shape as shown on drawing and directed by Engr-in- Charge. (Make: TATA/JINDAL).

(e) Making short rails obtained from item No 2.04 above and fixing all as shown on drawing.

(f) Making legs out of unserviceable long/short rails obtained from item 2.04 and 2.05 above including cutting, threading and fixing all as specified and directed by Engr-in-Charge.

FD-75(M) Chair CB Steel With Arm

(a) Removing the worn out paint by scraping from the steel surface, necessary preparation of surface for painting and welding wherever required, two coat of spray painting with synthetic enamelled paint olive green over a coat of Metal primer after dent/bent portion. Wooden surface should be black polish to required glazed and shine.

(b) Removing the worn out u/s seat frame and providing/fixing the new one of existing size made out of 1st class teak wood duly re-caning with new plastic cane 2mm thick oval shape for general weaving and 4mm thick plastic cane for beading all around as show in drg. Wooden frame should be finished with black polish and fix in its original position with required screw(plastic cane type-I HDPE).

(c) All as per item 3.02 here-in-before but back frame.

(d) Removing the worn out u/s handle made out of H.W(T.W) well seasoned and providing/fixing of exisiting size and shape with required screw after finish with black polish.

FD-75(M) Chair CB Steel Without Arm

(a) All as per item 3.01 here-in-before but for chair CB steel without arm

(b) All as per item 3.02 here-in-before but for chair CB steel without arm

(c) All as per item 3.03 here-in-before but for chair CB steel without arm

FD-1031 Almirah Steel large

(a) Taking out of broken door shutter from Almirah Large Steel and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting . All as directed by Engineer-in-Charge and shown on drawing

(b) Removing the worn out u/s handle from the almirah and providing/fixing of new handle chromium plated heavy duty as approved by Engr-in-Charge/GE.

(c) Removing the worn out u/s lock from almirah and providing/fixing with new lock 6 lever with deuplicate key ISI marked with round shape of MS key plate as approved by Engr-in-Charge/GE duly fixed as per drawing.

(d) Removing the worn out u/s 3 way locking device and providing/fixing the new one in its original postion as per drg.

(e) Removing the worn out u/s leg and providing / fixing the new leg made out of MS sheet 1.00mm thick in its original position duly welded as per drg.

(f) Taking out of u/s worn out shelf and providing the new one of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

(g) Removing the worn out paint from internal/external surface of almirah steel large by scraping. Necessary preparation of surface for painting duly dented/pitted and smoothen the surface by putty and painting the internal and external surface with two coat of synthetic enemalled paint over a coat of primer Metal to bring the surface to a glossy shine as directed by Engr-in-Charge.

FD- 1032 Almirah Steel Medium

(a) All as per item No 5.01 here-in-before but for almirah steel medium.

(b) All as per item No 5.02 here-in-before but for almirah steel medium.

(c) All as per item No 5.03 here-in-before but for almirah steel medium.

(d) All as per item No 5.04 here-in-before but for almirah steel medium.

(e) All as per item No 5.05 here-in-before but for almirah steel medium.

(f) All as per item No 5.06 here-in-before but for almirah steel medium.

(g) All as per item No 5.07 here-in-before but for almirah steel medium.

DB-3954 Chair CBA Office

(a) Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg. (i) Front leg. .

(ii) Rear leg.

(iii) Side rail

(iv) Front rail

(v) Back rail

(vi) Back rest batten horizontal

(vii) Long stiffener

(viii) Short stiffener

(b) Removing the all worn out plastic cane from chair and providing and re-caning of the same with new white plastic cane 2mm thick half round oval shape for general weaving and 4mm thick cane plastic for beading work all around as shown in drg (Plastic Cane Type -I HDPE)

(c) Preparation of surface by Remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. .

FD-229 Repair/Re-canning of chair Easy

Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg. (a) Front Legs

(b) Front rail of seat frame (Hole should be 12.5mm apart of each other)

(c) Side Rail

(d) Back Rail

(e) Arm Rest

(f) Remove the existing unserviceable canning and supply and weave with 2 mm thick new white plastic cane oval shape Godrej pattern and beading with 4mm thick new white plastic cane make Ajay /premier as approval by GE and providing new hard rubber shoes on legs below of chair Easy.

(g) Preparation of surface by Remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. .

FD-1027 Form w/o back

(a) Removing of U/S teak wood planks and S&F new planks mde out of teak wood 25mm thick x255mm wide x1525mm long duly french polished and fixed with 9 Nos GI Bolts .

(b) Removing of U/S legs from form w/o back and S&F new legs made out of 25mm sq conduit (16 guage) of existing shape & size duly painted with black enamelled paint over a coat of primer.

(c) Removing of U/S stiffners of form w/o back S&F new stiffners made out of 25mm sq conduit (16 guage) of existing shape & size duly painted with enamelled black colour over a coat of metal primer.

(d) Removing of U/S shoes of form w/o back and S&F new rubber PVC shoes of existing shape & size.

FD-1004 Table office clerk steel

(a) Removing old broken damaged top of table office clerk steel and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered with 19x4mm teak wood beading duly french polished all around the top.

(b) Removing old u/s internal cupboard/drawer locks from table office clerk steel and S/F new internal locks 40mm 4 lever with duplicate keys of approved quality.

(c) Taking out of u/s worn out drawer and providing the new one of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

(d) Repair of Drawer and worn out welding in drawer in its original position existing size and shape. All as shown on drg.

(e) Removing old broken u/s rubber shoes of table office clerk steel and S/F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of table office clerk steel

(f) All as per item No 5.07 but for table office clerk Steel.

FD- 1003 Table office officer steel

(a) Removing old broken damaged top of table office officer steel and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

(b) Removing old u/s internal drawer locks from table office officer steel and S/F new internal drawer locks 40mm 4 lever with duplicate keys of approved quality.

(c) Removing old broken u/s hard rubber shoes of table office officer steel and S/F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of table office officer steel complete all as specified and shown on drawing.

(d) All as per item No 5.07 but for table office officer Steel.

FD-1007 Table 900 x 600 x 760 mm Steel W/O/Drawer

(a) Removing old broken damaged top of table 900 x 600 x760 mm steel and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exterior grade with 19x4mm teakwood beading fixed with headless nails all around the top.

(b) Removing the existing steel long rail from Table 900x 600 x 760 mm and S & F new steel long rail of size : 25mm x 25mm x 1.6mm thick. All as shown on drg and directed by Engineer-in-Charge.

(c) Remove the existing MS legs from Table 900 x 600 x760 mmand S & F new leg made out of 25mm x 25mm x MS tube 1.6mm aell thickness. All as directed by Engineer-in-Charge and as shown on drg.

(d) Remove the existing stiffner bottom and S & F new stiffner bottom made out of 25mm x 25mm, MS tube of 1.6mm wall thickness. All as directed by Engineer-in-Charge and shown on drg.

(e) Remove the existing short stiffner and S & F new short stiffner made out of 25mm x 25mm, MS tube of 1.6mm wall thickness. All as directed by Engineer-in-Charge and shown on drg.

(f) Remove the existing unserviceable shoes from Table 900 x 600 x760 mm and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(g) Remove the existing worn out paint from Table 900 x 600 x760 mm and applying two coat of synthetic enamell paint black over a coat of primer. All as directed by Engineer-in-Charge and shown on drg.

FD/MAP/II/05 Repair of Chair Dinning

(a) Remove the existing unserviceable/broken PVC seat from chair dinning and supply & fixing the new PVC seat 4mm existing size in its original position all as shown on drg and directed by Engr-in-Charge.

(b) Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg. (i) Front Legs

(ii) Rear Legs

(iii) Front rail of seat frame

(iv) Side Rail

(v) Back Rail

(vi) Short stiffener

(vii) Back rest batten

(viii) All as per item No 7.10 here-in-before but for Charpoy wooden

FD-1029 Locker steel

(a) Removing old broken damaged hasp & stapples of locker steel and S/F new hasp & stappples of size 150 mm long chromium plated to the shutters of locker steel.

(b) Removing old broken handle of locker steel and S/F new handle of size 100 mm long 'D' Type chromium plated to the shutters of locker steel.

(c) Removing old broken hanging rod of locker steel and S/F new hanging rod made out of 20mm dia chromium plated pipe 500mm long of locker steel.

(d) All as per item No 5.07 but for Locker Steel.

FD-1009 Table 900 X900 X 760 mm steel

(a) Removing of old and unserviceable top of table 900 x900 x760 mm steel and S&F new top made out of 18/19 mm thick pre-laminated particle board (ISI Marked) exterior grade one side teak veneered finish and other side having balancing white lamination with 19 x 4 mm teakwood beading all around the top and polishing the wooden frame shall be with french polish(to the entire satisfaction subject to minimum two coats ) including preparation of surfaces by scrapping /smoothing the surface all specified and shown on drawing .

( b) Painting to steel frame of table 900 x900x 760 mm steel by synthetic enamelled paint(min two coats) olive green colour including preparation of old painted surfaces by scrapping out old dirt staints etc to the entire satisfaction ( painting shall be done by using compressure spray machine)

(c) Electric welding to the broken /dislocated 25 x 25 mm square tube rails of tables 900 x900x 760 mm steel , length of welding exceeding 2.5 cm but not exceeding 5 cm ( each spots measured separately) thickness of metal to be welded not exceeding 6 mm , complete all as directed.

(d) Removing old unserviceable rubber shoes from the legs of 900 x900x 760 mm and S&F new rubber shoes off approved quality and tightly fitted and the bottom of legs all as specified and shown on drawing

DB-4120 Table office clerk wooden

(a) Removing of old and u/s top of table office clk and S& F new top made out of 18/19 mm thick Prelaminated particle board teak veneered finish and provided with beading of teak wood size 19x4mm alround the top fixed with 20mm pannel pin complete all as directed and as shown on drawing

(b) Removing of old and u/s drawers of table office clk and S& F new drawers made out of Ist class teak wood well seasoned and 6mm thick ply wood (5 ply) commercial BWR gde complete all as directed and as shown on drawing

(c) Removing old & u/s knob from drawers of table office clerk wooden & S/F new stainless steel handle 75mm of approved quality complete as directed

(d) Removing of old and u/s long stiffners of table office clk and S& F new stiffners made out of Ist class teak wood well seasoned complete all as directed and as shown on drawing

(e) Remove of the old unsv existing short stiffner and supply and fixed new short stiffner of existing shape and size made of 1st class hard seasoned teak wood free from knots duly french polished..

(f) Remove of the old unsv existing long rail and supply and fixed new rails made of 1st class hard seasoned teak wood free from knots duly french polished.

(g) Remove of the old unsv existing short rail and supply and fixed new rails made of 1st class hard seasoned teak wood free from knots duly french polished.

(h) Remove of the old unsv existing legs and supply and fix new legs of existing shape and size made of 1st class hard seasoned teak wood free from knots duly french polished.

(j) All as per item No 7.10 here-in-before but forTable office clerk wooden.

FD/MAP-II/01 Charpoy Hard Top MAP

(a) Remove the existing unserviceable Ply wood from Charpoy ip sq with ply and making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

(b) Remove the existing unserviceable shoes from Charpoy Hard Top MAP and and S & F new PVC Shoes. All as directed by Engineer-in-Charge and shown on drg.

(c) All as per item No 5.07 here-in-before but for Charpoy Hard Top MAP

FD-1038 Rack Steel 6 Tier (closed type)

(a) Removing of unsv worn out back of rack steel closed type and S & F new back to rack steel closed type made of MS Sheet of 1 mm thick of eixsting shape and size and making functional.

(b) Removing of unsv sides of rack steel closed type and S &F new sidesmade of 1 mm thick MS Sheet in its original position as per drg & making functional

(c) Removing of unsv shelves of rack steel closed type and S & F new shelves made of 1 mm thick MS Sheet in its originnal position as per drg & making functional

(d) Removing of unsv MS angle iron from rack steel closed type and S & F new MS angle iron to rack steel closed type in its originzl position as per drg & making functional

(e) All as per item No 5.07 here in before but for Rack steel closed type.

FD-39 FMN Set /Frame for bed/charpoy

(a) Painting of complete set of Fmn with black enamelled paint over a coat of metal primer after removal of existing work out paint.

FD-165(M) Table dining ORs

(a) Removing old broken damaged top of table dining OR and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exterior grade with 19x4mm teakwood beading fixed with headless nails all around the top. Top will be covered with Almn sheet 20 gauge.

(b) Removing the existing steel long rail from Table Dining ORs and S & F new steel long rail of size : 25mm x 25mm x 1.6mm thick, 1575mm long. All as shown on drg and directed by Engineer-in-Charge.

(c) Remove the existing MS legs from Table Dining ORs and S & F new leg made out of 25mm x 25mm x MS tube 1.6mm well thickness. All as directed by Engineer-in-Charge and as shown on drg.

(d) Remove the existing stiffner bottom and S & F new stiffner bottom made out of 25mm x 25mm, MS tube of 1.6mm well thickness. All as directed by Engineer-in-Charge and shown on drg.

(e) Remove the existing stiffner Top and S & F new stiffner top made out of 25mm x 25mm, MS tube of 1.6mm well thickness. All as directed by Engineer-in-Charge and shown on drg.

(f) Remove the existing unserviceable shoes from Table Dining OR's and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(g) Remove the existing worn out paint from Table Dining OR's and applying two coat of synthetic enamell paint black over a coat of primer. All as directed by Engineer-in-Charge and shown on drg.

FD- 1023 Side rack w/3 tray steel

(a) Repair of side rack with 3 tray Steel by means of denting ,welding & scrapping wherever required making the frame in its original position and making functionel all as per drg and directed by engr- in- charge.

(b) Removing of unsv MS angle iron fromSide rack with 3 tray steel and S & F new MS angle iron to side rackwith 3 tray steel closed type in its originzl position as per drg & making functional

(c) Removing of unsv shelves of side rack with 3 tray steel and S & F new shelves made of 1 mm thick MS Sheet in its originnal position as per drg & making functional

(d) Remove old worn out paint from side rack with 3 tray steel byscraping with required grade of sand paper and. The rack shall be painted with two coat of spray painting by synthetic enamelled paint OG/Grey colour over a coat of red oxide primer all as directed by Engineer-in-Charge.

FD/E6/MAP/12 Chair Writing Steel

Replace the following worn out parts of Chair writing Steel as shown in drawing and directed by Engr-in-Charge:- (a) Seat shall be 12mm thick hot pressed plywood Upholstered with febric and moulded polyurethene foam with PVC lipping all round. The polyurethene foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter thick and hardness 20 kg on humpden machine

(b) Back shall be 12mm thick hot pressed plywood Upholstered with febric and moulded polyurethene foam with PVC lipping all round. The polyurethene foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter thick and hardness 20 kg on humpden machine

(c) Hand rest shall be made of black integral skin polyurethene with 75-85 shore 'A' Hardness & Reinforced with MS insrest. It shall be scratch and wheather Resistant Size 210mm (Inner) and 230mm (Outer)

(d) All as per item No 5.07 here-in-before but for Chair writing Steel.

FD-388 (R) Charpoy IP Folding

(a) Remove the existing unserviceable Ply wood from Charpoy ip sq with ply and making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

(b) Remove the existing unserviceable shoes from Charpoy IP Folding and and S & F new PVC Shoes. All as directed by Engineer-in-Charge and shown on drg.

(c) All as per item No 5.07 here-in-before but for Charpoy IP Folding

FD/MAP-II/03 Table dining 6 Pers (MAP )

(a) Removing old broken damaged top of Table dining 6 Pers and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

(b) Removing old & u/s legs of Table dining 6 Pers & S/F new legs of size 750x45x90mm made out of 1st class well seasoned teakwood duly fixing PVC rubber shoe at the bottom of legs with mild steel screws complete all as directed & shown on drg.

(c) Taking out old & u/s long rail and S&F new long rail of size 1500 x 45 x 90 mm made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

(d) All as per item No 24.03 here-in-before but short top rail of size 900 X 45 X 90 MM .

(e) Removing old & u/s MS Right angle from the corner of table dining 6 Pers and providing and fixing new one of size 150 x 30 x 5 mm with mild steel screws complete all as directed & shown on drg.

(f) Remove the existing unserviceable shoes from table dinning 6 pers and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(g) All as per item No 7.10 here-in-before but for Table dining 6 Pers.

FD/MAP-II/03 Table dining 4 Pers (MAP )

(a) All as per item No 24.01 here-in-before but for Table dining 4 Pers

(b) Removing old & u/s legs of table dinning 4 pers & S/F new legs of size 750x45x90mm made out of 1st class well seasoned teakwood duly fixing PVC rubber shoe at the bottom of legs with mild steel screws complete all as directed & shown on drg.

(c) Taking out old & u/s long rail and S&F new long rail of size 1200 x 45 x 90 mm made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

(d) All as per item No 25.03 here-in-before but short top rail of size 900 X 45 X 90 MM .

(e) Removing old & u/s MS Right angle from the corner of table dining 4 Pers and providing and fixing new one of size 150 x 30 x 5 mm with mild steel screws complete all as directed & shown on drg.

(f) Remove the existing unserviceable shoes from table dinning 4 pers and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(g) All as per item No 7.10 here-in-before but for Table dining 4 Pers.

FD-284 Table 900x600x760mm without drawer/with drawer FD- (FD-42(m), FD-41(m) FD-291, FD-284, FD-283)

a) All as per item No 24.01 here-in-before but for Table 900x600x760 mm without drawer / with drawer.

(b) Removing old u/s following components of table 900x600x760mm with or without drawer & S/F with new components made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg :- (i) Legs (size 740x60x30mm)

(ii) Long rails (740x25x65mm)

(iii) Side rails ( size 440x25x65mm)

(iv) Side stiffiner (740x25x130mm) for FD/41/FD-284

(v) S& F new drawer

(vi) Remove the existing unserviceable shoes from table 900x600x760mm with or without drawer and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(c) All as per item No 7.10 here-in-before but for Table 900x600x760mm without drawer/with drawer.

FD-88(M) Table 900x900x760mm wdn

(a) All as per item No 24.01 here-in-before but for Table 900x900x760 mm.

(b) Removing the following broken/damaged components/parts of table 900x900x760mm & S/F new components as under made out of Ist cl well seasoned teakwood all as per drg :- (i) Legs of size (60x35x760mm long)

(ii) Top rails of size (75x25x900mm long)

(iii) Remove the existing unserviceable shoes from table 900x900x760mm and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(c) All as per item No 7.10 here-in-before but for Table 900x900x760mm .

FD-281 Sofa set 2 Seater

(a) Removing of old worn out u/s front legs of sofa set 2 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(b) Removing of old worn out u/s rear legs of sofa set 2 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(c) Removing of old worn out u/s front rail of sofa set 2 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(d) Removing of old worn out u/s Back rail of sofa set 2 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(e) Removing of old worn out u/s Arm Rest Sofa and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(f) Removing of old worn out u/s back wdn bearers of sofa set 2 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(g) Removing of old worn out u/s bottom wdn bearers of sofa set 2 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(h) Remove the existing unserviceable sofa cushion from sofa set 2 seated and supply and fixing the new cushion 100 mm thick x 40 density of size 530x560mm covered with new tapestry cloth duly stitched. Make: Kurlon/sleep well

(j) All as per item 7.10 here-in-before but for sofa set 2 seater.

Charpoy IP Square Tube

(a) Remove the existing unserviceable Ply wood from Charpoy ip sq with ply and making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

(b) Remove the existing unserviceable shoes from Charpoy IP Square Tube and and S & F new PVC Shoes. All as directed by Engineer-in-Charge and shown on drg.

(c) All as per item No 5.07 here-in-before but for Charpoy Hard Top MAP

FD-220 Charpoy GI Pipe

(a) Remove the existing unserviceable nylon newar from Charpoy GI Pipe and making the frame to its original position by tightening etc and Supply & Weave with new nylon newar 50mm- 55mm width white colour non-recycled. The weaving shall be close with 33 and 14 Nos bands both on long and short rail respectively. The weight of nylon newar shall not be less than 1.5 Kgs per charpoy

(b) Removing the unserviceable/broken check nuts form GI charpoy & supply and fix 6mm thick GI Medium grade check nuts suitable for 32mm dia GI pipe all as specified and shown on drawings (Each check nut will be measured as single unit)

(c) Removing the unserviceable broken 3 way GI elbow from GI charpoy and S & F 32 mm dia GI medium grade 3 way elbow ISI marked all as specified and shown on drg and directed (Each GI Elbow shall be measured as single unit)

(d) Removing the existing unserviceable/broken long rail from GI charpoy and S & F new long rail of GI tubing 32mm including cutting, threading and bringing the GI charpoy into the original shape as shown on drawing and directed.

(e) Removing the existing unserviceable/broken short rail from GI charpoy and making short rails obtained from item No 30.04 above including cutting, threading and fixing all as shown on drawing.

(f) Making legs out of unserviceable /short rails form GI charpoy and making legs out of unserviceable long/short rails obtained from item 30.04 and 30.05 above including cutting, threading and fixing all as specified and directed.

FD-86 (M) Trestle Store Room Wooden

Repairs to the following parts of wooden trestle by new parts of appropriate size and shape with timber SAL as directed by Engr-in-Charge & Specified. (a) S&F 2nd class Hard wood legs of size 405x100x100mm

(b) S&F 2nd class Hard wood Top Batten (Middle of size 2400x60x100mm)

(c) S&F 2nd class Hard wood Batten (Side) of size 2440x100x100mm

(d) S&F 2nd class Hard wood Batten (Short) of size 600x100x60mm

(e) Repair to loose wooden trestle, Providing clamp piece of size 300mm x 40 mm x 5mm `L` shape with 6 nos screw including painting with black paint.

(f) Preparation of surface of wooden trestle of any description and treated with two coats of creosote oil all as specified.

FD-1043 Trestle Store Room Steel

(a) Repair of Trestle Store Room Steel by means of denting ,welding & scrapping wherever required making the frame in its original position and making functionel all as per drg and directed by engr- in- charge.

(b) Removing the worn out paint from internal/external surface of Trestle Store Room Steel by scraping. Necessary preparation of surface for painting duly dented/pitted and smoothen the surface by putty and painting the internal and external surface with two coat of synthetic enemalled paint over a coat of primer Metal to bring the surface to a glossy shine as directed by Engr-in-Charge.

FD-157(M) Table Bed side steel

(a) Removing of existing U/S top of table bed side steel and S&F new top of made out MS sheet 1.00 mm thick of existing size & shape

(b) Removing of existing door shutter and S&F new door shutter made out of M/S sheet 1.00 mm thick of existng shape & size .

(c) Removing of U/S shoes of table bed side steel and S&F new hard rubber PVC of existing shape & size

(d) All as per item No 5.07 here in before but for Table bed side steel.

FD-81(M) Stool steel 305x305x760mm

(a) Repair of Stool Steel by means of denting ,welding & scrapping wherever required making the frame in its original position and making functionel all as per drg and directed by engr- in- charge.

(b) Remove old worn out paint from Stool Steel 305 X 305 X 760 mm byscraping with required grade of sand paper and. The frame shall be painted with two coat of spray painting by synthetic enameled paint OG/Grey colour over a coat of red oxide primer all as directed by Engineer-in-Charge including supply of suitable rubber shoes 04 Nos to each .

FD-99(M) Board Notice 2400x1220

(a) Removing of unsv / broken existing door glass from board notice and S&F new door glass of 4 mm thick of existing shape and size and making functional

(b) Removing of unsv / broken existing door shutter 2 way from board notice and S&F new door shutter of existing shape and size and making functional

(c) Removing of unsv / torn out existing baize green cloth from board notice and S&F baize green cloth of existing shape and size and making functional

(d) Removing of unsv existing soft wood board from board notice and S&F new soft wood board 19 mm thick of existing shape and size and making functional

(e) Removing of unsv existing wooden frame of board notice and S&F new wooden frame made of hard seasoned teak wood of existing shape and size and making functional

(f) All as per item No 7.10 here in before but for Board Notice

FD-279 Repair/Re-canning of Chair Dinning

Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg. (a) Front Legs

(b) Rear Legs

(c) Front rail of seat frame (Hole should be 12.5mm apart of each other)

(d) Side Rail

(e) Back Rail

(f) Short stiffener

(g) Back rest batten

(h) Remove the existing canning and supply and weave with 2mm thick new white plastic cane oval shape godrej patern and beading with 4mm thick new white plastic cane as apporeved by GE.

(j) Removing of old u/s rubber/PVC shoes from Chair Dining & S/F new rubber shoes of apporoved quality & fixed at the bottom of legs of Chair Dining

(k) Preparation of surface by Remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge.

M/S Ali Trading Co

M/S MADAN MOHAN KAKAR

Ms GHOSH AND SONS

HALLIOX ENTERPRISES