CONSTRUCTION OF VOCATIONAL LAB OF SIZE 7 X 10.60 MTR UNDER PM SHRI SCHEME PAN INDIA AT KV NO 1 BALASORE UNDER GE I R AND D CHANDIPUR

Amount

NOTE (Applicable for all items) :- (i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. (ii) The bidders / contractors are advised to quote same rate for same items as mentioned in all parts of BOQ If quored rates are different for same items, lower quoted rate shall be considered for same items as mentioned in BOQ. For this account nothing extra shall be admissible by this Deptt. SCHEDULE 'A' PART-I (Building)

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil including removal of soil complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30cm depth, 1.5m in width as well as 10 sqm on plan), including including getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m in all kind of soil complete all as specified and directed.

All as per item No 1.002 but exceeding 1.5m or part thereof in depth beyond the the first 1.5m

Excavation in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft /loose soil complete all as specified and directed.

All as per item No 1.004 but exceeding 1.5m or part thereof in depth beyond the the first 1.5m complete all as specified and directed.

M&L for soling under foundation with well brunt old size bricks laid in dry complete all as specified

M&L for sand filling under floors/Paver block or in foundations including watering and consolidation complete all as specified and directed.

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 using 40 mm graded aggregate in foundation, filling and mass concrete complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter etc complete all as specified and directed.

M&L for RCC, M-30 Design mix as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slab, under mass concrete complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangle or polygon (Superstructure) complete all as specified and directed.

M&L for RCC, M-30 Design mix as in column, pillars, piers, posts and struts (Substructure & Superstructure) complete all as specified and directed.

M&L for RCC, M-30 Design mix as in chajjas complete all as specified and directed.

M&L for RCC, M-30 Design mix as in beams, cantilevers, bressumers, lintel over 1.5 mt span all as specified and directed.

M&L for RCC, M-30 Design mix as in slabs supported on walls, roof beams and column in floors, roof, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping)

Formwork to chullah hoods, chajjas, troughs and similar items including edges

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape requied, including cracking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securing with clips

M&L for mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape requied, including cracking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securong with clips

M&L for mild steel TMT Bars 6mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6 m mean radius, built in old size bricks in cement mortar CM (1:6)

M&L for Brickwork with flyash bricks, straight or curved on plan any radius in half brick thick walls, built in cement mortar CM (1:4)

M&L for 40mm thick PCC(1:2:4) B0 Damp proof course to horizontal or vertical surfaces including necessary formwork

Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m

M&L for 10 mm thk cement plaster in C:M (1:6) and finished the surface even and fair above dado/ skirting as specified.

M&L for 15 mm thk cement plaster in CM (1:4) with liquid water proofing compound on external surface and finished the surface even and smooth without using extra cement.

Supply only liquid Water Proofing Compound all as directed

M&L for (Ceiling Plaster) 5 mm thick cement plaster in CM (1:3) on soffit of RCC slab, beams, lintel and projection as specified

M&L for Hardcore of guage n exc 63mm broken stone or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 75 mm thick PCC (1:4:8) type D-2, using 40mm graded aggregate all as specified and directed.

M&L for 30mm thick PCC (1:2:4) type B-0, using 12.5mm graded aggregate all as specified and directed.

M&L for Vitrified tiles 600x600x8-9 mm thick, over 15mm bedding layer in CM (1:6) all as specified and directed.

All as per item No 39 but as in skirting over 10mm thick screed bed in CM (1:4) to match the floor finish/border as specified

M&L for Non-Skid Ceramic tiles 7-8mm thick of size 300x300mm over 15mm bedding layer in CM (1:6) as specified.

M&L Glazed ceramic colour tiles in vertical surface 450 X 300 X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles over 10mm thk backing in CM (1:4) complete all as specified and directed.

M&L granite slab (of any type) 18-20 mm thick machine cut, bedded and jointed with gray cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including cutting and polishing over 15mm thk screed bed in CM (1:4) complete.

All as per item No 1.043 as in skirting/dado over 10mm tk cement mortar backing in CM (1:4)

M&L for machine cut kota stone slab flooring 18-22mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20mm thick cement mortar screed bed or bedding layer in CM (1:6) completed all as specified and directed.

M&L for kota stone slab 18-22mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick cement mortar backing in CM(1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with MS square tube, suppling and fixing in opening complete.

S&F of factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel moulded both side Prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles prelam PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of both side Prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement.

S&F 100 mm size of Stainless steel hinges complete all as specified and directed. (ISI Marked)

S&F 125 mm long extruded Aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F aluminium sliding door bolt 300 mm long, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F Continuous (piano) hinges, width of flaps (when open) in 30 mm Stainless steel finish or electro galvanised complete all as specified and directed.

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor.

S&F 125 mm long extruded Aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 100 mm long extruded Aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 150 mm long extruded Aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F Aluminium Hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws

S&F 150 mm long extruded Aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F for providing and fixing factory made uPVC white colour Sliding window Three track area not exceeding 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm(+-.2mm). Window profile with hollow section with multi chamber. Frame (108mm x 45mm), Sliding sash (39mm x 58mm), Sliding mesh sash (39mm x 58mm). Sliding interlock (One vertical lenth in each shutter) (35mm x 45mm), Glazing bead (20mm x 18mm) will be miterd cut and fusion welded at all curners, including drilling of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware. EPDM gasket ,1.2 +-0.2mm thick galvanised steel Frame (32mm x 13.5mm) 2 Nos, sliding sash (29mm X 19mm), sliding mesh sash (29mm x19mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire clith 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note :The unit rate quoted by contractor excludes cost of glass, wire mesh and includes all other connected accessories. Net opening will be measured for payment purpose)

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of EIC. (Glass shall be paid separately).

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with SS wire staple all as directed by EIC.

M&L for 5.00 mm thick sheet glass, ordinary quality incl necessary fixing all as specified and directed by EIC.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size Frame size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

All as per item No 1.063 but in Frame size 45 x 70 mm for cup board

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

All as per item No 1.065 but in 18 mm thick Cup Board Shutter

M&L for providing and fixing of stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth. above skirting on wall & ceiling as specified

M&L for two coats of plastic emulsion paint over a coat of interior primer incl preparation of surfaces all as specified.

M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work on ceiling surface over a coat of primer incl preparation of surfaces all as specified.

M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work on wall over a coat of primer incl preparation of surfaces all as specified.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth. above skirting on wall complete all as specified

M&L for preperation newly plastered surface of walls and finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm all as specified and directed.

S&F stainless steel fancy type 20mm dia curtain rod of 1.25mm thick wall thickness with bracket and all accessorie all as directed

S&F in Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)against wall in CM 1:2 securing urinal to plugs with and incl 60mm long screw, grating and union for discharge pipe all as directed.

S&F Vitreous China wash down water closet pan EWC, white(excluding fixing bolts, flushing cistern and flush pipe) all as specified and directed

S&F vitreous china wash basin, white, flat back size 550x400mm, incl cutting for and pinning in ends of brackets or erecting stand but excl taps, pvc conections but incl brackets, waste pipe, waste coupling in repairs

S&F Plastic seat cover white for EWC, closed pattern with flat bottom and cover with CP hinging device complete all as directed.

S & F PVC valve less symphonic action type flushing cistern 10 ltr capacity low level white with inlet ball valve, float flush pipe and handle including bracket complete all as specified and directed.

S&F PVC (SWR) 75mm floor trap, plain with grating including jointing with solvent cement all as specified and directed.

Supplying and laying CPVC pipes SDR 11 & plain CPVC SDR 11 fittings of size 20mm outer dia on walls/ceilings or laying in floors etc complete all as specified and as directed.

All as per item No.1.081 here in before but of size 25mm outer dia.

S & F of CPVC special fitting, Brass Elbow (3/4 X ½) suitable for 20mm outer dia CPVC pipe complete all as specified and as directed.

S&F of CPVC special fitting, Female Brass Threaded Adaptor (FTA/FBTA) suitable for 20mm outer dia CPVC pipe complete all as specified and as directed

S&F for PVC connections 15mm size with PMT nuts of length 600 mm complete all as specified & directed.

S&F fancy type bib taps 15mm with wall flange, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Supplying and laying of CPVC Ball Valve outer dia 25mm fitting on walls/ceilling or laying in floors complete all as specified.

S&F Stop/angle valves fancy type CP 15mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S & F Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixedand fixed complete all as specified and as directed.

S&F for CP two way Bib Cock 15mm bore all as specified & directed

S&F PVC grating doom 100 mm dia complete all as specified and directed.

S&F Brass CP tubular towel rail, 15mm dia, "D" type, 60 cm long between flanges all as directed.

S&F CP Health faucet et all as specified and as directed(ABS) with 1 Mtr. tube & hook complete all as specified.

S&F stainless steel sink, 0.80mm thick for kitchen with plug, waste pipe, washer including cantilever cast iron bracket, connecting union overall size 495 mm x 420 mm with bowl size 410 mm x 330 mm x 160 mm

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard railing 60 cm long.

S&F PVC (SWR) pipes, single socketed, in any length , with rubber rings 110mm dia

S&F 110 mm PVC (SWR) vent cowl all as specified and directed.

S&F 75 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints, laid in trenches or fixed to wall complete as spd and directed.

S&F 75 mm dia PVC (SWR) bends any radius complete as specified and directed.

S&F 110 mm PVC(SWR) bend any radius complete all as specified and directed

S&F Rotational moulded water tank 1000 litre polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as spd and directed.

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

M&L for 25mm thick PCC (1:2:4) type B-0, using 12.5mm graded aggregate all as specified and directed.

M&L for rendering 10mm thick CM(1:3) on roof top concrete surfaces with WPC and finished the surfaces even and smooth without using extra cement complete all as specified.

M&L for plain cement concrete 75mm thick (1:3:6) type C-1 (using 20mm graded stone aggregate) as plinth protection and finished the surface even and smooth without using extra cement complete all as specified.

M&L for plain cement concrete (1:3:6) (nominal mix) type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M&L brick work with fly ash bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) all as specified.

M&L for rendering 15mm thick in cement mortar (1:3) on wall finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:4) on wall surface and finished even a fair complete all as specified and as directed.

M&L for RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in precast cement concrete for cover slab set in cement mortar (1:6) with necessary form work complete all as specified and as directed.

S&F 150mm dia HDPE double wall corrugates SN-8 underground drainage/sewer pipe conforming to IS 7328 single socketed in any length jointed with solvent cement laid in treches complete all as specified and as directed.

M&L for plain cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate bed to drain pipes including forming cradal against the sides of pipes after they are laid and tested for 150mm bore pipes complete all as specified and as directed.

Returning, filling with including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in side of MH.

Removing excavated material (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5m complete all as specified.

M&L for PCC (1:2:4) type B0 using 12.5mm graded aggragate as in coping, haunching, bed plate of rungs etc complete all as specified and as directed.

M&L 0.50 mm thick pre painted galvalume aluminium zinc coating GI based corrugated/ semicorrugated steel sheet of any colour as in roof covering with self tapping screws complete all as specified and directed.

S&F for mild steel work in roof trusses, purlin, rafters with angle, channel etc including distance pieces cleats etc complete with Fe-290 Gde E-165 complete all as specified and as directed.

M&L preparing new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer incl preparation of surfaces complete all as specified & directed.

S&F melamine white board/marker board non magnetic type of size 6ft x 4ft with smoother surface allowing for rapid marking and erasing of marking on their surface. The board shall be aluminium framing and the surface is melamine based resin quoted, fixed to wall surface with necessary fixing accessories complete all as specified and directed.

NOTE (Applicable for all items) :- (i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. (ii) The bidders / contractors are advised to quote same rate for same items as mentioned in All parts of BOQ If quored rates are different for same items, lower quoted rate shall be considered for same items as mentioned in BOQ. For this account nothing extra shall be admissible by this Deptt. SCHEDULE 'A' PART-II (Path)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. in all kinds of soil.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement & pigment complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge

M&L preparing concrete surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a priming paints plaster coat.

NOTE (Applicable for all items) :- (i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. (ii) The bidders / contractors are advised to quote same rate for same items as mentioned in All parts of BOQ If quored rates are different for same items, lower quoted rate shall be considered for same items as mentioned in BOQ. For this account nothing extra shall be admissible by this Deptt. SCHEDULE 'A' PART-III (Ext water supply & Sewage Disposal)

M&L for making connection of G.I. distribution branch with G.I. main of size upto 50 mm by providing and fixing tee, including cutting and threading the pipe etc. complete all as specified and directed.

Supply and fixing 40 mm dia nominal bore G.I. pipes medium grade complete with G.I. fittings etc. laid in trenches complete all as specified and directed.

Providing and fixing 25 mm dia nominal bore G.I. pipes medium grade complete with G.I. fittings etc. and fixed complete to wall and ceilings all as specified and directed.

Providing and fixing 25 mm nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end) complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as equired complete all as specified.

NOTE (Applicable for all items) :- (i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. (ii) The bidders / contractors are advised to quote same rate for same items as mentioned in All parts of BOQ If quored rates are different for same items, lower quoted rate shall be considered for same items as mentioned in BOQ. For this account nothing extra shall be admissible by this Deptt. SCHEDULE 'A' PART-IV (External Electric Supply)

Supply, connecting and testing PVC insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 4 core 70 sq. mm complete all as specified and as directed.

M&L for sand filling around the cable with coarse sand for sand cushioning of under ground cable including spreading and punning down to desired thickness complete all as specified and as directed.

M&L for laying of fly ash bricks for cable protection cover laid flat and dry in trenches over the cable prependicular to the direction of cable all as directed.

Supply and fix GI Pipe light grade 40mm dia for cable protection in trenches/ at PCC pole for loop in/loop out of cable and cable entry at Bldg/block end complete all as specified and directed

Providing and fixing 100 A, 16KA rating and breaking capacity and four pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required & directed by Engr-In-Charge.

NOTE (Applicable for all items) :- (i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. (ii) The bidders / contractors are advised to quote same rate for same items as mentioned in All parts of BOQ If quored rates are different for same items, lower quoted rate shall be considered for same items as mentioned in BOQ. For this account nothing extra shall be admissible by this Deptt. SCHEDULE 'A' PART-V (Internal Electrification)

M&L for concealed point wiring for One light/fan point controlled by one switch with 1.5 Sq mm (nominal area), FRLSH grade, PVC insulated, single core,sheathed stranded copper conductor cable of 1100 Volt grade, multi stranded in and including rigid non metalic medium grade PVC conduit of size 20mm concealed in wall, incl suitable modular metal boxes flush to wall with suitable cover plates controlled by one switch with and including continuous 1.5 Sqmm PVC insulated FRLSH single core copper conductor cable as earth continuity conductor connected to common earth dolly etc. complete all as specified and directed by Engr-in-Charge. Note : (i) The cost of making good the disturbed surfaces is deemed to be included in the unit quoted rate. (ii) The cost of cutting chases is deemed to be included in the unit quoted rate.

All as per item No 5.01 above but one 5 amps 5 Pin socket outlet on independent board

All as per item No 5.01 above but with FRLS PVC insulated copper conductor cable of size 2.5 Sqmm and 2.5 Sqmm for earth continuity conductor for 16A switch socket on independent board complete all as specified and directed.

S&F Modular type socket out let 2/3 pin, 6/16 Amps, 2 module all as specified and as directed.

S&F Modular type switch single pole 16 Amps one way, 1 module all as specified and as directed

S&F Modular type switch single pole 6 Amps, 1 module, one way all as specified and as directed.

S&F Modular type Socket outlet 6 Amps 2/3 Pin, 2 module complete all as specified and directed.

S&F ceiling rose surface mount PVC/Polycarbonate, isolated body with two/three terminals complete all as specified and directed.

S&F energy saving high power LED building security light of 35W or next higher rating, minimum luminous output 120 lum/watt, 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete complete all as specified & as directed .

M&L for GI bracket for bldg security light fittings made out of 25 mm light grade GI pipe bended one portion of 45 cm at 120 degree to shape of appx 1.5 mtr, duly painted with two coats of silver enamel paint including 2 Nos of MS clamp of flat iron size 40x6 mm, nut bolt washers complete all as specified and as directed.

S&F wall / surface mounted LED light fitting 20 W or next higher rating (4 FT), IP 20, CRI > 80, CT> 6500 K, THD<10%, minmum lumen output 120 lumen per watt with poly carbonate body with all accessories internally prewired and including connecting up with and including twin/three core twisted flexible conductor cable of suitable size incl flexible hose complete all as specified and as directed.

S&F wall / surface mounted LED light fitting 10 W or next higher rating (2 FT), IP 20, CRI > 80, CT> 6500 K, THD<10%, minmum lumen output 120 lumen per watt with poly carbonate body with all accessories internally prewired and including connecting up with and including twin/three core twisted flexible conductor cable of suitable size incl flexible hose complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m cpomplete all as specified and as directed.

S&F ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and as directed.

S & F stepped type fan regulator, 120 W, 2 module complete all as specified and as directed.

S&F internet socket RJ-45, suitable for CAT 6 cable ,sheilded, folded metal 1 module complete all as specified and directed.

M&L for 20mm (external dia) Rigid non-metallic medium grade PVC conduit concealed to wall for internet cable exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.

Material and labour for earthing complete with galvanized iron earth plate electrode in 60 cm x 60 cm x 6 mm thick buried directly in ground vertically at a depth not less than 2.25 meter below ground level with top edge of earth plate at depth not less than 1.5 mtr below ground level connecting to and including GI wire 4 mm dia by means of GI bolts, nuts, check nuts and washer. Provide light grade 15 mm dia GI protection pipe connected to switch board /test point, GI pipe medium grade 20 mm dia for watering, funnel wire mesh, common salt of required quantity (not less than 7 kg) , charcoal dust, RCC pit cover of 50 mm thick ( reinforcement of 8 mm dia Iron rod and centre to centre distance upto 100mm) and earthing chamber of PCC 1:3:6 type C-1 with 20 mm graded stone aggregate including excavation and earth work disposal of surplus soil al as specified and shown as plate No 3 of SSR part - I 2009 and complete all as specified and as sirected. Note: Above item will be measured and paid after completion of sucessful testing.

S&F in repair 4 Way TPN DB,IP43,IK-09, 415 Volts, Metal Double Door, with Busbar and blanking plates, Neutral link and SP MCBs as outgoings,flushing to wall/fixing inside enclosure and making good the disturbed surfaces with all other accessories including necessary connection complete all as specified and directed by Engr-in-Charge.

S&F in repair MCB, SP,C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 kA all as specified and dircted by Engr-in-Charge.

S&F in repair MCB, TPN of capacity 40 Amps,C-Series 415 Volts with breaking capacity 10 kA all as specified and dircted by Engr-in-Charge.

M/S BIJAY KRUSHNA MAITY (BID ID -3409886)

Rekha Enterprises (BID ID -3411066)

M/s D.K Mukherjee & Co (BID ID -3407341)

M/S ABHISHEK JENA (BID ID -3407700)

chauhan syndicate (BID ID -3406050)

vaishnaveedevienterprises (BID ID -3408562)

DS ENTERPRISES (BID ID -3407945)