PROVIDING AND LAYING OF SYNTHETIC TRACK AT MUNSHI RAM GUPTA PARK WARD NO.139, KAROL BAGH, RAJINDER NAGAR CONSTITUENCY (AC-39).

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

PROVIDING AND LAYING IN POSITION CEMENT CONCRETE OF SPECIFIED GRADE EXCLUDING THE COST OF CENTERING AND SHUTTERING - ALL WORK UP TO PLINTH LEVEL :1:5:10 (1 CEMENT : 5 COARSE SAND (ZONE-III): 10 GRADED STONE AGGREGATE 40 MM NOMINAL SIZE) (AS PER DIRECTION OF OFFICER IN CHARGE.)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

PROVIDING AND LAYING OF EPDM FLOORING OF 15MM THICKNESS , APPLYING AIRETHANE PRIMER OVER DRY CEMENT CONCRETE SURFACE, LAYING 13MM BASE LAYER MADE OF SBR GRANULES 1-4MM , BINDED TOGETHER USING AIRETHANE BINDER, SEALED USING SBR BLACK DUST BINDED IN AIRETHANE SEALANT. LAYING 2MM AIRETHANE TOP COAT TOPPED WITH MATT FINISH COATING (EDMP) AND MARKED WITH LINE PAINT (AS PER DIRECTION OF OFFICER IN CHARGE.)

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade :13.64.1 Two or more coats on new work sqm

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. 16.59.1 Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm