PROVN OF TOILET BLOCK NEAR S-6 POST OF CIF (R) SIG REGT UNDER AGE(I) CIF(R)

Amount

Excavating over areas, n exc 1.5m deep and getting out in soft/loose soil, complete all as specified.

Removing excavated soil exc. 250 m but n exc. 500 m and depositing where directed

Surface dressing in any type of soils not exc. 15 cm deep and removing surplus materials to a distance exc. 250 mtr as directed by Engr-In-Charge.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil, complete all as specified and directed.

M&L for hard core of broken boulder n exc 63 mm, deposited, spread and levelled in layers n exe 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as foundation filling and mass concreate, complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified.

Returning filling in, including spreading ,leveling ,watering and well ramming in layers not exc 25 cm complete all as specified.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for 40mm thick cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in sub floors finished even and rough to receive the topping layer complete all as specified and directed.

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 using old size bricks, complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls finished even and smooth complete all as specified and directed by engr-in-charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls finished even and smooth complete all as specified and directed by engr-in-charge.

Rendering 5mm thick plaster in CM 1:3 on ceiling fair faces of brick/concrete surfaces rough finished even and smooth without using extra cement complete all as specified.

M&L for applying three coats of white washing on ceiling including preparation of newly plastered surfaces complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint on walls complete all as specified and directed by Engineer-in-charge.

M&L for non skid ceramic colour tiles 8 to7mm thick ( square/rectangle) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or beddding layer in CM 1:4, complete all as specified and directed.

M & L for Glazed ceramic coloured printed tiles (first quality) of size 350 mm x 250 mm x 7 mm/450 mm x 350 mm x 7 mm thick as in vertical surface, dado/skirting, over and including 15 mm thick rendering in CM 1:4, complete all as specified and directed.

Solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M S square tube, suppling and fixing in opening as per specification and drawing as per SSR Pt-II 2020, complete all as specified and directed.

Supply and fixing factory made 30 mm PVC rigid foam panel door shutter made from mild steel tubular frame of size 19 mm x19 mm for stiles and 15 mm x 15 mm for top and bottom rails and covered with 5 mm thick head moulded PVC channel having width of 50 mm to form stiles and PVC street of width 75 mm to form rock rail, bottom rail and top rail or either side having panels inserted with 5 mm thick PVC sheet sealed with solvent cement adhesive to the stiles and rails with 5 mm x 25 mm PVC sheet beading on either side including three Nos. aluminium hinges for each door complete all as per manufacturer instructions complete all as specified and directed.

S & F 200 mm aluminium anodised barrel tower bolt of extruded section ISI marked and fixed,complete all as specified and directed.

S&F 300 mm long aluminium alloy, sliding door bolt, ISI marked with hasp, staple ( bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, all as specified.

S & F 100 mm long butt hinges, medium wight cold rolled mild steel, ISI marked, complete all as specified and directed.

S & F 150 mm extruded aluminium alloy handles, fabricated type, anodisedand, complete all as specified and directed.

S&F Rotational moulded polyethelyne water storage tank HDPE three layered (cylindrical vertical with closed top hoisted fixed in position all as specified in SSR part-I, capacity of tank 500 ltr incl inlet and outlet connection 20mm dia and 15mm dia GI pipes medium grade respectively, complete all as specified.

S&F vitrous china wash basin,white, counter type,flat back of size 550 mm x 400 mm with and including CP pillar tap and CP waste coupling, angle brackets, PVC connection 450 mm longhaving PTMT nuts and 32 mm dia PVC waste pipe, complete all as specified and directed

Supply and fix Vitreous China squatting pan orissa pattern size 580 x 440 mm white (Ist quality) with 'P' or 'S' trap, front or black inlet and integral foot rests including connection to trap and to flushing pipe, complete all as specified & directed.

S&F Vitreous china Urinal, Half stall type, white (excluding flushing cistern and flush pipe ) complete incl providing and fixing plugs, beddding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screw, pointing around urinal back in cement; including waste pipe,complete all as specified and directed.

Supply and fixing 100 mm bore cast iron soil, waste and vent spun pipes ISI maked in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified. NOTE :- Excavation and earth work shall be measured and paid separatly

All as per ser item No 29.00 here in before but 75 mm bore pipe.

All as per ser item No 30.00 here in before but 75 mm bore pipe fixed to wall.

S & F 100 mm bore dia Cast iron bend (any radius) diminishing pieces or tapers(larger bore measured) with all fittings, complete all as specified and directed.

All as per ser item No 32.00 here in before but 75mm bore dia.

S & F cast iron branch pieces single (equal or unequal ordinary or inverted or with parallel branches) for 100mm bore with oval access doors, complete all as specified and directed.

S & F cast iron vent cowls suitable for 100 mm bore of pipe, complete all as specified and directed.

S & F 150mm X 150mm size salt-glazed stoneware gully trap square or round mouthed type 'P' setting and jointing to drain pipes in cement mortar 1:1, complete all as specified and directed.

M & L for cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps cills chases for concealed water tubing not exc. 10cm girth, complete all as specified and as directed.

S&F 15 mm bore dia steel water tubing 'medium grade' galvanised with all fitting (i.e. Tee, socket, bend etd) complete to walls and ceilings or laid in floors, complete all as specified and directed by Engr-in-Charge.

S&F 20 mm bore dia steel water tubing 'medium grade' galvanised with all fitting (i.e. Tee, socket, bend etd) complete to walls and ceilings or laid in floors, complete all as specified and directed by Engr-in-Charge.

S&F bib taps, fancy type, chromium plated, cast copper aloy ISI marked with crutch or butter fly handle high pressure screwed down for iron pipe of 15mm bore complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore stop cock, fancy type, chromium plated with long shank and cup (concealed type) screwed down,high pressure,with crutch or butterfly handle.screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. Note: Weight of stop cock shall not less than 0.575 Kg)

S&F stop valve, cast copper alloy ISI marked screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20 mm bore complete all as specified.

S&F stop valve, cast copper alloy ISI marked screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified.

S&F15mm bore angle valve chromium plated screwed down fancy type high pressure screwd both ends for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F PVC connection 15 mm dia with brass nuts of length 450 mm complete all as specified.

S&F CP grating 100mm dia with or without hole complete all as specified.

S&F centre hole basin mixture valve, cast copper alloy fancy type 15mm brass chromium plated mixer (central hole basin mixer w/o pop up waste system) for mixing hot & cold water screwed down for iron pipe , complete all as specified.

S&F for 110mm bore, PVC (SWR) rain water drainage pipes single socketed in any length with rubber ring joints included bends fixed to walls/floors complete all as specified.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, skirting/dados including 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M & L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in fixing of hold fast, coping, band, bed plates, lintels upto 1.5m clear and similar items including weathering slightly rounded or chamferred angles and throughting including necessary form work, complete all as specified and directed.

Reinforced cement concrete M-25 (Design Mix) ( using 20 mm graded aggregate) as slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, all as specified and directed by Enge-in-Charge.

RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc and mass concrete all as specified

Reinforced cement concrete M-25 (Design Mix) ( using 20 mm graded aggregate) as in beams, cantilevers, bressummers, lintel over 1.5m clear span, complete all as specified.

M&L for reinforcement cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregates as in columns, pillar,piers, posts and struts, complete all as specified.

M & L for 40 mm thick damp proof coarse in cement concretet (1:2:4) type B-0 (using 20 mm graded crushed stone aggregate) as in damp proof course to horizontal or vertical surfaces including necessary formwork, complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal/sloping), fair finished surfaces concrete flat complete all as specified and directed by engr-in-charge.

Use and waste Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished Add for fair surfaces of finished concrete complete all as specified and directed by engr-in-charge.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, contilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough furnished surface of concrete complete flat, all as specified.

Formwork to sides of concrete foundations, bases for column beams, plinth beams and soffits of foundation and pllinth beams and similar work (rough finished), complete all as specified and directed.

Mild Steel TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

Mild Steel TMT bars 6 to 8 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

On site CONVENTIONAL type LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, 150 mm thick PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for capacity of 3000 ltr,complete all as specified and directed. Note : Rate quoted shall deemed inclusive of Earth work.

Construction of Soakage well of size 1.8m dia and 3.0m effective depth in excavation in any type of soil foundation in PCC 1:3:6 , walls of honey combed and solid brick work in CM 1:4, RCC M-25/SFRC cover slab filling with bats as shown in drg No TD CE/TD-1202/2003 sheet No 1/2 and 2/2 dt 09.10.2003, complete all as specified in drg, complete all as specified and directed. Note : Rate quoted shall deemed inclusive of dewatering during construction if met with.

M&L for salt glazed stone ware drain pipes of internal diameter 150 mm grade 'A' laid in trenches and jointed complete all as specified . Note:- The rate include for cutting hole to existing manhole for any dia and making good to be done inside and out side by the contractor and no extra payment to be contractor

M&L for 150 mm bore salt glazed stone ware bends and taper bends, any radius complete all as specified .

Surface excavation in soft/loose soil not exceeding 30cm deep and averaging 15 cm deep and getting out complete all as specified.

M & L for 75 mm thick plain cement concrete 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in sub base finished even and rough to receive the topping layer, complete all as specified and directed by Engineer-in-Charge.

Machine pressed precast concrete interlocking paver block coloured any shape and size as approved conforming to IS 15658 of 60mm thick M-35 grade of grey cement and pigment & laid all as specified and directed

Supply and fix Gun-metal, globe or gate valves 25mm dia, with iron wheel head, screwed both ends for iron pipe and fixed

Cutting existing steel tubing 50 mm bore for alterations or additions (Each cut measured) necessarily done in position without taking down, complete all as specified and directed.

M&L Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector), complete all as specified and directed.

M&L for point wiring concealed type with PVC insulated unsheathed copper cable FRLSH 1.5 sqmm multi stranded two single copper conductor in and including suitable size PVC conduit pipe 20 mm dia complete with all accessories and with 1.5 sqmm PVC insulated copper cable FRLSH continous earth wire, re-recessed mounting pressed steel GI sheet box 2 mm thick suitable for modular switch/socket of adequate size including iner and outer white cover plate of modular complete all as specified and directed for followings :-

One light point/ fan controlled by one switch 5 Amp.

One socket outlet 5Amp controlled by one switch on same board.

Supply and Fixing switch piano type 6 Amps one way 230 volts AC complete all as specified and as directed

Supply and Fixing socket outlet 5 pin, 6 Amps flush type 230 volts AC complete all as specified and as directed

Supply and fixing sheet metal enclosure MCB distribution board SPN 4 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S&F of Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body, complete all as specified and as directed

Supply and fixing of Endura Linear NEO wall mounted LED Batten 20 Watt LED, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver complete all as specified and directed.

Material and fixinf of PVC/polycarbonate lamp holder insulated body with back plate batten/angle type for batten fitting complete all as specified.

Supply and fixing of MCB single pole 6 to 30 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

Supply and fixing of MCB SPN 40 to 63 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

M&L earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

M&L GI Earth wire size 04 mm as earth continuty conductor.

Supply and fixing LED Bulbs white /warm white (as per demand) in colour of 10 Watt,B-22 base Cap, complete all as specified and directed.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fix of exhaust fan made of steel body AC single Phase, 230V, 50 Hz,RPM 1400, Copper winding of sweep 300mm with. Blades, frame and louvers complete all as specified.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 6 Sqmm 2 core, complete all as specified and directed by Engineer-in-Charge. NOTE:(Earth work, brick protection and sand cushioning shall be measured and paid for separately).

Sand cushioning with fine sand to under ground cables in trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable as specified in clause 19.75 of SSR Part-I, complete all as specified and directed by Engr-in-Charge.

M&L for Brick covering with width equal to length of brick as mechanical protection to cables with well burnt sub class ‘B’ (old size) bricks laid dry flat, complete all as specified and directed.

Steel tubing galvanized (medium grade) 25 mm bore conforming to IS-1239 for passing cable under road/floor or fixing to poles for protection of underground cable complete with Flat iron 50x6mm clamps made to shape and 12mm dia bolts, nuts and washers for fixing where required. NOTE :- Excavation and earth work shall be measured and paid separatly

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of ₹ NIL during AOC Note:- Tenderers shall not quote for this Schedule

arneesh kumar suri (BID ID -3089452)

J. PRO BUILDERS (BID ID -3091023)

M/S RAHUL GUPTA (BID ID -3086733)