Health assessment of civil structures at South Site and one civil structure at hill side, BARC, Trombay, Mumbai

NDT Test: Conducting ultra sonic pulse velocities tests, at all locations prepared after chipping the plaster, on columns, beams and portal frames to assess the integrity of concrete as per BIS/ASTM specifications etc. complete.

Conducting rebound hammer test as per BIS/ASTM standards etc. complete.

Extraction and testing of concrete drill dust samples from the structure. Three drill dust samples from depths 0-15mm, 15-30mm and 30-45mm shall be collected from each location. The samples shall be tested for chlorides, sulphates, PH and alkalinity.

Conducting test: Preparing the surface of RCC structural member such as beams, columns, slabs, water tank walls & slab etc by chipping the plastered surface/finishing/cladding to expose the concrete, cutting etc as per S-516(Part 5/Sec 3):2021 and conducting carbonation test at various depth as directed by EIC.

Conducting profometer scan at specified location of the structure for reinforcement steel location, size and cover measurement, etc. complete.

Determining the surface tensile strength and bond strength of concrete (Pull Off) as per ACI 503.1R/ASTM C1583 including preparing concrete surface, drilling the concrete, bonding concrete with disk with rapid set epoxy and conducting test on old surface and newly repaired suface as directed by Engineer -In-Charge.

Preparation and submission of two copies of draft report as specified followed by five copies of final report along with a soft copy of the same on diskette covering Non Destructive test observations, analysis, interpretation and conclusions of NDT observations, drawing out measures for durability make up, estimation of repair quantities, rate, rate analysis for major repair items. Note: 1. The rates quoted for item No. 1 to 10 shall include preparation of test area, making good the areas with polymer modified mortar, disposing off debris for testing

Conducting distress mapping Analysis for buildings/sheds of south site where NDT to be carried out such as REDS, S-70, IRE Substation, S-50-53, S-60-64, S-32A, B&C, SSZ, S-88&86, Traffic control and change room, S-90, S81 . Distress symptoms will be marked on floor plan as per notation used or as directed by Project Engineer and preparing data sheets mentioning exact location of each crack, height, and width of crack and Preparation and submission of two copies of draft report as specified followed by five copies of final report along with a soft copy of the same on diskette covering distress mapping Analysis observations and conclusions along with photos etc., Complete as directed by Engineer-in-Charge. Note: Condition Survey of the area under consideration shall be carried out, which includes a) Visual Inspection: Grouping of structural members should be done during visual inspection based on environmental exposure conditions e.g. external and internal members. Also, identification of Corrosion prone locations as per Visual Inspection. Follow the notations and typical worksheet for recording distress during visual inspection and damage classes based on visual inspection as per CPWD handbook on repair. The condition survey report shall comprise the output of visual inspection and NDT results. Major sections to be covered in the report shall be: (i) Identification of the cause of the distress. (ii) Systematic documentation of all observations during visual inspection, including distress maps. (iii) Systematic documentation of all test results obtained from NDTs. (iv) Determination of concrete properties based on NDTs (v) Requirement of propping of structural members to relieve part/full load acting on the member. (vi) Requirement of immediate evacuation and safety measures to prevent any immediate major mishap. (vii) Recommendations on repair/retrofit strategy with due consideration to available space and accessibility for ongoing activities. (viii) Requirements on safety measures to be adopted during execution of repair/retrofit jobs. (ix) Limitations/assumptions used. (x) Any other recommendation.

Providing and fixing double tubular scaffolding system using H- frames with cup lock type on the exterior side upto seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre horizontal and vertical tubes joining with cup and lock system with M.S. tubes, M.S. tube challies, M.S clamps and M.S staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and as approved by the Engineer -in - charge. The elevational area of the scaffolding shall be measured for payment purposes. The payment shall be made once irrespective of duration of scaffolding