Loading
Loading…
Loading…
Tender Value
₹55.6 L
EMD Value
₹1.1 L
Closing Date
30 Mar 2026, 11:00 amClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Capital (Works)
Above/Below/Par
TECHNICAL
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of [V/N or 'V' whichever is less; where V = Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must submit a valid Electrical Contractor license as per Indian Electricity Rules for the respective category of works issued by the Government Electrical License Board on or before the closing date of the tender. A copy of which should be submitted along with the tender offer; otherwise, the tender will be summarily rejected.
The Similar nature of works for this instant tender shall be "Supply,installation, testing and commissioning of any LT/HT electrical work." The tenderer should have executed the similar nature of works in Central/State Government department or PSUs of Central /State Government."
Experience in similar nature of work:- a) The tenderer must have successfully completed any of the following during last 07(seven) years, ending last day of month previous to the one in which tender is invited: Three similar nature of works each costing not less than the amount equal to 30% of the advertised value of the tender, or Two similar nature of works each costing not less than the amount equal to 40% of the advertised value of the tender, or One similar nature of work each costing not less than the amount equal to 60% of the advertised value of the tender. (b) (i) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. And in the case of major bridges - substructure, superstructure etc.), the tenderer must have successfully completed any of the following during last 07 (seven) years, ending the last day of the month previous to the one in which tender is invited: Three similar nature of works each costing not less than the an amount equal to 30% of the advertised value of each component of the tender, or Two similar nature of works each costing not less than the amount equal to 40% of the advertised value of each component of tender, or One similar nature of work each costing not less than the amount equal to 60 % of the advertised value of each component of the tender. Note for b(i): Separate completed works of minimum required values for each component shall also be considered for fulfillment of technical eligibility criteria. (b) (ii) In such cases, what constitutes a component in a composite work shall be clearly predefined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (iii) To evaluate the technical eligibility of the tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility shall be considered. The scope of work covered in other remaining components shall be either executed by the tenderer himself if he has work experience as mentioned in clause 7 (a) (ii) of Part-II of GCC or through subcontractor fulfilling the requirements as per clause 7 of Part-II of GCC or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfillment of technical eligibility. In case after the award of the contract or during the execution of work it becomes necessary for the contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of Part-II of GCC, with prior approval of the Chief Engineer in writing.
51 conditions · 4 needing a document upload
Whether the cost of earnest money deposited
WHETHER VALID ELECTRICAL CONTRACTOR LICENSE SUBMITTED
Migration to GST regime - Special Tender Conditions: The rates should clearly indicate the rate of applicable duties and taxes included in the prices quoted by them. Any variation in tax structure/ rate due to introduction of GST, shall be dealt with under Statutory Variation Clause. It should be ensure that bidders/tenderers are GST compliant and quoted tax structure/rates are as per GST Law.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Contractor should submit the GSTIN number and same should be mentioned in the bills along with a copy of GSTIN registration certificate while submitting the bills to accounts for audit and payment, As GST is scheduled to implemented wef 01.07.2017. Without GSTN, no bill will be accepted w.e.f. 01.07.2017
From 01.07.2017 GST has been implemented but the detail guideline is still not clear. Hence, new tax structure on materials and labour will be applicable to both Railway & contractor after getting proper notification
Payment of Earnest Money deposit (EMD) , in respect of e- tendering,should be accepted through net banking or online payment gateway only
Electrical work against At GHY- Replacement of leaky roofing sheets at PF -1 , 2&3, 4&5 and 6&7 and damaged kota stone flooring by industrial flooring at PF -1 both end , improvement of water vats for better drinking water facilities , Renovation of waiting halls at PF-1 and other miscellaneous works at Guwahati Railway Station under the jurisdiction of SSE/W/GHY
EL-LM-25-26-43
EL-LM-25-26-43
Open
Works - General
90 Days
Hojai, Assam
₹0
₹1.1 L
30 Mar 2026
6 Mar 2026
16 Mar 2026
61 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 55,61,808.47 | ||
| — | 125.00 | — | — | ||
| Supply, installation, testing and commissioning of raised solar PV module mounting structure over existing north-facing GI/tin shed to orient the solar modules towards true south direction at optimum tilt angle. The work includes design, fabrication and erection of galvanized steel raised mounting structure suitable for installation above the existing shed of Platform No. 1 and Parcel Loading/Unloading Shed (in front of Child Care Room), complete with necessary structural supports, base plates, anchor fasteners, bracings, corrosion protection and all associated accessories as per relevant IS standards and MNRE guidelines. The structure shall be designed to withstand applicable wind loads and site conditions, ensuring safe clearance from the existing roof and proper alignment for maximum solar energy generation. The work also includes all labour, materials, tools, testing and commissioning complete as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 9,58,750 | |
| — | 100.00 | — | — | ||
| Supply, installation, testing and commissioning of superstructure solar PV module mounting structure over the roof of Post Office, Canteen and MCO Building, including design, fabrication and erection of galvanized steel mounting frames suitable for rooftop solar panel installation. The work shall include provision of necessary structural supports, base plates, anchor fasteners, bracings, corrosion protection and all associated accessories required for proper fixing of solar PV modules at optimum tilt angle and orientation for maximum energy generation. The mounting structure shall be designed to withstand applicable wind loads and site conditions as per relevant IS standards and MNRE guidelines. The scope also includes all materials, labour, tools, testing and commissioning complete as per tender specifications and as directed by the Engineer-in- Charge. | — | — | — | 11,21,000 | |
| — | 4000.00 | — | — | ||
| Supply, installation, testing and commissioning of 4 sq. mm DC solar cable for interconnection of solar PV modules and associated equipment, complete with laying, dressing, termination and necessary accessories. The work shall include testing and commissioning of the DC cable network; however, existing DC cables may be utilized after thorough inspection and testing, if found in serviceable and usable condition. Any additional cable required shall be supplied and installed as per relevant IS standards and MNRE guidelines, complete with all labour, materials and accessories as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 2,92,640 | |
| — | 900.00 | — | — | ||
| Supply, installation, testing and commissioning of 6 sq. mm multistrand copper AC cable (green colour) to be used as earthing conductor, complete with laying through suitable conduit/tray, dressing, termination, ferruling and connection to the designated earthing points. The work shall include all necessary accessories, labour, testing and commissioning to ensure proper continuity and effective earthing of the solar PV system, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 69,615 | |
| — | 55.00 | — | — | ||
| Supply, installation, testing and commissioning of 70 sq. mm aluminium ring type cable lugs suitable for proper termination of aluminium conductors, including crimping, ferruling and fixing at required locations. The work shall include provision of all necessary accessories, labour and tools required for secure and reliable cable termination, complete in all respects as per relevant IS standards and tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 605 | |
| — | 90.00 | — | — | ||
| Supply, installation, testing and commissioning of 16 sq. mm copper pin type cable lugs suitable for proper termination of copper conductors, including crimping, ferruling and fixing at required locations. The work shall include provision of all necessary accessories, labour and tools required for secure and reliable cable termination, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 648 | |
| — | 105.00 | — | — | ||
| Supply, installation, testing and commissioning of 6 sq. mm copper ring type cable lugs suitable for proper termination of copper conductors, including crimping, ferruling and fixing at required locations. The work shall include provision of all necessary accessories, labour and tools required for proper cable termination, ensuring secure electrical connection, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 551.25 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing and commissioning of aluminium blind rivets of size 4 mm x 19 mm for fastening and fixing of structural members, sheets or accessories, including drilling, riveting and securing at required locations. The work shall include provision of all necessary materials, labour, tools and accessories required for proper installation, complete in all respects as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 8,260 | |
| — | 240.00 | — | — | ||
| Supply, installation, testing and commissioning of MC4 type DC connectors suitable for solar PV applications, for proper termination and interconnection of DC solar cables between PV modules and associated equipment. The work shall include crimping, connection, insulation and testing to ensure safe and reliable DC connectivity, complete with all necessary accessories, labour and tools as per relevant standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 21,806.4 | |
| — | 100.00 | — | — | ||
| Supply, installation, testing and commissioning of end clamps suitable for solar PV module mounting structures for proper fixing of modules at the edge positions of the mounting frame. The work shall include provision of aluminium end clamps with necessary SS fasteners, nuts, bolts and washers for secure mounting of solar PV modules on the structure, complete with all materials, labour, tools and accessories as per tender specifications and as directed by the Engineer- in-Charge. | — | — | — | 3,481 | |
| — | 500.00 | — | — | ||
| Supply, installation, testing and commissioning of mid clamps suitable for solar PV module mounting structures for proper fixing of adjacent solar modules on the mounting frame. The work shall include provision of aluminium mid clamps with necessary stainless steel fasteners, nuts, bolts and washers to ensure secure and firm mounting of solar PV modules, complete with all materials, labour, tools and accessories as per tender specifications and as directed by the Engineer- in-Charge. | — | — | — | 18,585 | |
| — | 600.00 | — | — | ||
| Supply, installation, testing and commissioning of Allen bolts of suitable size and grade for fastening and securing components of the solar PV module mounting structure, including tightening, fixing and alignment at required locations. The work shall include provision of necessary nuts, washers and accessories, complete with all materials, labour and tools required for proper installation, as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 12,036 | |
| — | 20.00 | — | — | ||
| Supply, installation, testing and commissioning of 300 mm long heavy-duty nylon cable ties for proper dressing, bundling and securing of electrical and DC cables of the solar PV system. The work shall include fixing at required locations to ensure neat cable management and safe routing, complete with all materials, labour and accessories as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 6,000 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing and commissioning of 500 mm long heavy-duty nylon cable ties for proper dressing, bundling and securing of electrical, AC and DC cables of the solar PV system. The work shall include fixing at required locations to ensure proper cable management, safe routing and neat installation, complete with all materials, labour and accessories as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 3,800 | |
| — | 3000.00 | — | — | ||
| Supply, installation, testing and commissioning of EPDM rubber washers suitable for solar PV module mounting structures, for providing proper sealing and vibration isolation at fastening points. The work shall include placement and fixing of EPDM washers along with bolts, nuts and fasteners to prevent water ingress and ensure durable installation, complete with all materials, labour and accessories as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 10,620 | |
| — | 20.00 | — | — | ||
| Supply, installation, testing and commissioning of silicone sealant for sealing of joints, gaps and openings in solar PV installation works to prevent water ingress and ensure weatherproofing. The work shall include proper surface preparation, application of sealant at required locations and finishing, complete with all materials, labour and accessories as per tender specifications and as directed by the Engineer-in- | — | — | — | 5,600 | |
| — | 500.00 | — | — | ||
| Supply, installation, testing and commissioning of 32 mm size uPVC casing-capping for routing and protection of electrical cables, including cutting, laying, jointing and proper fixing on wall/ceiling surfaces at required locations. The work shall also include supply, installation, testing and commissioning of necessary GI screws, PVC gutka and other accessories for firm fixing of casing-capping. The complete work shall be executed at different locations under SSE/P/GHY jurisdiction, including all materials, labour, tools and accessories, complete in all respects as per relevant IS standards, tender specifications and as directed by the Site Engineer/Engineer-in-Charge. | — | — | — | 13,375 | |
| — | 120.00 | — | — | ||
| Supply, installation, testing and commissioning of 25 mm dia flexible uPVC conduit pipe for protection and routing of electrical cables, including laying, cutting, bending and proper fixing at required locations. The work shall include provision of all necessary accessories such as couplers, saddles, bends, junctions and fasteners for complete installation. The conduit shall be installed neatly ensuring proper cable protection and routing, complete with all materials, labour, tools and accessories as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 10,860 | |
| — | 151.00 | — | — | ||
| Supply, installation, testing and commissioning of PVC bends of suitable size for use with PVC/uPVC conduit pipes for smooth change of direction in cable routing. The work shall include proper fitting, jointing and fixing with the conduit system, ensuring neat installation and protection of cables, complete with all materials, labour, tools and accessories as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 2,151.75 | |
| — | 15.00 | — | — | ||
| Supply, fitting and fixing of PVC wall plugs of 35 mm size for fixing of electrical accessories, supports and fixtures on wall/ceiling surfaces. The work shall include drilling of holes, insertion of PVC wall plugs and proper fixing with suitable screws at required locations. Each set shall consist of 100 Nos., complete with all labour, tools and accessories as per tender specifications and as directed by the Engineer-in-Charge | — | — | — | 708 | |
| — | 15.00 | — | — | ||
| Supply, fitting and fixing of shaved head wood screws of size 50 mm x 9 mm for fixing of electrical accessories, clamps, supports and fixtures on wooden surfaces or PVC wall plugs. The work shall include proper insertion and tightening of screws at required locations, complete with all materials, labour, tools and accessories. Each set shall consist of 100 Nos., and the work shall be executed as per tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 1,593 | |
| — | 26.00 | — | — | ||
| Supply, erection, testing and commissioning of copper plate earthing consisting of copper earth plate of size 600 mm x 600 mm x 6 mm buried in ground with complete construction of earthing pit including excavation, placement of plate, backfilling with alternate layers of charcoal and salt, watering arrangement and provision of RCC/CI cover with frame. The work shall also include supply and fixing of copper earth continuity conductor in the form of copper flat of size 40 mm x 5 mm of 15 m length, securely connected to the earth plate with suitable nuts, bolts and washers. The earthing terminal shall be properly connected to the neutral terminal of the transformer and integrated with the earthing system as required. The complete work shall include all materials, labour, tools and accessories, testing of earth resistance and commissioning, as per relevant IS standards, tender specifications and as directed by the Site Engineer/Engineer-in-Charge. | — | — | — | 2,53,724.64 | |
| — | 1760.00 | — | — | ||
| Supplying, laying, testing and commissioning of 25 mm x 5 mm G.I. strip for earthing/earth continuity conductor, including laying along the required route and terminating with suitable G.I. nuts, bolts, spring washers and plain washers as required. Jointing of the G.I. strip shall be carried out by proper overlapping and fixing with two sets of G.I. nuts, bolts and spring washers spaced at 50 mm apart to ensure effective electrical continuity. The work shall include all materials, labour, tools and accessories required for proper installation and termination, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in- Charge. | — | — | — | 2,53,440 | |
| — | 20.00 | — | — | ||
| Design, supply, installation, testing and commissioning of outdoor type Pre-Cooling Power Distribution Panel fabricated from 16 SWG CRCA sheet steel, vermin and dust proof, duly powder coated in Siemens grey shade, suitable for outdoor/wet location installation. The panel shall be provided with suitable cable entry for 120 sq. mm, 4 core LTUG cable with proper cable gland arrangement and locking facility. The panel shall be equipped with R-Y-B LED type indication lamps and suitable capacity copper bus bars. The panel shall comprise one no. 125 A, 4 Pole MCCB (25 kA breaking capacity) with adjustable thermal and fixed magnetic settings as incomer and one no. industrial type 125 A capacity 3P+N+E socket outlet of IP-65/67 rating as outgoing, complete with proper fixing and locking arrangement for connecting plug. The work shall also include supply and fixing of suitable glands, lugs, sleeves, terminals, PVC troughs and all necessary accessories for proper wiring and termination. The panel shall be provided with necessary mounting arrangements for installation on wall/pole/pillar as per site conditions. The complete work shall include design, fabrication, supply, installation, testing and commissioning, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 9,98,280 | |
| — | 200.00 | — | — | ||
| Supply, providing, fixing, testing and commissioning of G.I. chain link fabric fencing of required width with mesh size 25 mm x 25 mm, fabricated from 3 mm diameter G.I. wire, including necessary strengthening with 2 mm diameter G.I. wire. The work shall include fixing with suitable nuts, bolts, washers and other fastening accessories for proper installation. The fencing shall be erected neatly and securely at the required location, complete with all materials, labour, tools and accessories as per site requirements and as directed by the Engineer-in-Charge. | — | — | — | 3,37,480 | |
| — | 70.00 | — | — | ||
| Supply, laying, fixing, testing and commissioning of IP-65 rated Loop-in Loop-out junction box with metric knockouts for cable entry, made of polycarbonate/thermoplastic enclosure of size 205 mm x 255 mm x 112 mm, suitable for termination of 25 sq. mm aluminium conductor. The work shall include provision of suitable cable entry arrangements, clamps, nuts, bolts, glands and other accessories for proper cable termination and secure mounting. The junction box shall be installed through wall/ground/pole as per site requirement, ensuring proper protection against dust and moisture ingress. The complete work shall include all materials, labour, tools and accessories, executed as per relevant IS standards, tender specifications and as directed by the Site Engineer/Engineer-in-Charge. | — | — | — | 2,52,833 | |
| — | 60.00 | — | — | ||
| Supply, installation, wiring, testing and commissioning of PP Shed light point through good quality hard PVC conduit pipe with all associated accessories for surface type wiring. The wiring shall be carried out with 1.5 sq. mm single core PVC insulated flexible copper conductor cable, complete with necessary bends, couplers, junction boxes, saddles and fixing accessories. The point shall be controlled by one no. 5/6 Amp flush type switch mounted on hard plastic moulded board. The work shall include all materials, labour, tools and accessories required for proper installation, testing and commissioning, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 9,514.8 | |
| — | 16.00 | — | — | ||
| Supply, installation, wiring, testing and commissioning of PP Shed ceiling fan point through good quality hard PVC conduit pipe with all associated accessories for surface type wiring. The wiring shall be carried out using 1.5 sq. mm single core PVC insulated flexible copper conductor cable along with earth continuity provided by 16 SWG bare copper wire. The point shall be controlled by one no. 5/6 Amp flush type switch mounted on a hard plastic moulded board and provided with one no. 300 W box type stepped electronic fan regulator. The ceiling fan connection shall be made through a ceiling rose. The complete work shall include all materials, labour, tools and accessories required for proper installation, testing and commissioning, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge. | — | — | — | 4,254.88 | |
| — | 8.00 | — | — | ||
| Supply, fixing, testing and commissioning of 6-way SPN MCB Distribution Board conforming to IS: 8623 (Part-1 & 3) and IEC: 61439 (Part-1 & 3), with IK-08 impact protection rating, fabricated from CRCA sheet steel, powder coated in RAL-9003 shade, complete with single glazed door and having protection class of IP-43. The DB shall be provided with one no. 32 Amps DP C-curve MCB as incomer and four nos. 16 Amps SP B-curve MCBs as outgoing circuits, complete with bus bars, neutral link, earth bar and all internal wiring. The complete SPN MCB DB arrangement shall be properly concealed and fixed on the wall at the designated location as per site requirement. The work shall include supply of all necessary accessories, materials, labour, tools and fixtures required for proper installation, testing and commissioning, complete in all respects as per relevant IS standards, tender specifications and as directed by the Engineer-in-Charge at site. | — | — | — | 38,600 | |
| — | 275.00 | — | — | ||
| Design, supply, installation, testing and commissioning of indoor LED trunking lighting system comprising extruded aluminium trunking housing of 1200 mm / 2400 mm / 3600 mm length with associated mounting and interconnection accessories. The system shall include 40 W trunk-mounted LED luminaires of Surface Mounting Device (SMD) type, integrated with industrial grade constant current LED driver with efficiency 85% and short-circuit protection. The luminaire housing shall be fabricated from CRCA sheet steel with white powder-coated finish and fitted with milky polycarbonate diffuser for uniform light distribution and glare reduction. LED performance parameters shall include luminous efficacy 100 lm/W at 350 mA drive current, colour rendering index (CRI) 80, correlated colour temperature (CCT) as per project specification, and rated operational life 50,000 hours. The system shall be suitable for surface or suspended mounting with all mechanical and electrical accessories, including mounting brackets, connectors, cable entries, terminations, and end caps. Quantities shall be calculated in multiples of 1200 mm: 1200 mm = 1 No., 2400 mm = 2 Nos(2 x 1200 mm modules)., 3600 mm = 3 Nos.(3 x 1200 mm modules) The complete installation shall comply with relevant IS/IEC standards, project general specifications, and shall include testing, commissioning, and demonstration of full operational functionality at site.The cost includes full design, supply, fabrication, installation, interconnection, termination, testing, commissioning, and demonstration of operational functionality at site, complete with all materials, labour, tools, and accessories, as per tender specifications and directions of Engineer-in-Charge. | — | — | — | 8,50,995.75 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
El-LM-25-26-43._1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .