Construction of Immunodeficient Animal Research Facility (Phase -2) for ICTREC

Amount

Civil Work

Providing, machine mixing and laying M15 grade plain cement concrete (PCC) of required thickness for foundation, rafts, plinth beams, levelling course and all locations, etc. (minimum cementitious content shall be as specified in the IS Code and as approved); including compacting, curing, required shuttering and its removal, dewatering where required and vibrating, cleaning, preparing surfaces, junctions, etc.; complete at all depths and leads as per the drawing and to entire satisfaction of the site incharge / Engineer .

Providing, machine mixing and laying designed mix / Ready mix M30 grade reinforced cement concrete (RCC) for column, slab, beam, walls, staircases etc. as listed below (and at any other elements not listed), using 20mm nominal size well-graded approved quality aggregate and M sand as per approved design mix as per IS code and with minimum cement content as per IS or as specified by Structural consultant, whichever is more; maximum water cement ratio 0.42 including using approved admixtures, vibrating / compacting, curing, scaffolding, cleaning, preparing surfaces, junctions, hacking closely surfaces to be plastered etc. complete but excluding the cost of Formwork and reinforcement to the entire satisfaction of the Engineer incharge at all depths, heights, lifts and leads.

Beams /Columns / Shear Wall / Lift Walls/RC Beams at all levels Lintel beams / Chajja ALL FLOOR LEVEL /RC Slabs at all levels Staircase including steps ALL FLOOR LEVEL /equipment pedestal

Providing, fabricating, erecting and fixing in position water proof plywood centering and shuttering true to line and level, including required height's steel propping and staging, at all heights/levels, applying shuttering removal chemical emulsion/oil as approved, required bracing, if specified chamfering exposed edges, corners of beams, columns, walls etc., making leak proof joints etc. complete, at all leads and lift. Also include safely removing and dismantling the aforesaid assembly after specified or as approved period from the day of casting of concreting to the satisfaction of the Engineer incharge. The item shall also include the required staging and supporting arrangements. Soffit of slabs shall be fair face finished with no undulation of more than 2mm permitted. Any defect noticed shall be corrected by grinding or as approved by Engineer incharge, at Contractor's cost. The staging and formwork design shall be submitted to the Engineer incharge and got approval from Structural Consultant before proceeding to erect the same. Upto a Height of 6.5m

Note :- The form work and support for the contraction strips of (1m wide) as observed in structural drawings shall be mandatorily kept for the duration of 40 days in each floor. The rate shall be inclusive of the same and no extra shall be paid towards this.

Columns / Shear Wall / Lift Walls/RC Beams at all levels Lintel beams / Chajja/RC Slabs at all levels Staircase including steps

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to two story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S.clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineering-charge .The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. This also includes provision of Steel Props upto 5MT Capacity for support of beams, slab etc.

Providing, transporting to site, storing, de-coiling (if required), straightening, cutting, bending, spirally hooping, binding and placing, in position reinforcement bars, to correct shape and size as per detailed drawings, specifications, preparing and getting approved bar-bending schedules for all reinforced concrete work such as walls, columns / stub columns, beams, slabs, staircase etc.; with correct size of heavy duty PVC / concrete (of same grade of concrete) cover blocks and galvanized binding wire of 18 gauge, couplers in place of laps permitted, required dewatering, provide required labour and machines / equipment / tools / tackles for handling, shifting, bending, binding, etc. The measurement shall be as per IS 1200. The rate shall include cost of concrete cover blocks, binding wire, all chairs, spacers and pins etc. all complete to the satisfaction of the Engineer incharge at all depths, height, lift & leads.

TMT HYSD bars - Fe-500D/550D grade confirming to IS 1786.

Providing fixing M.S. (Class "C") sleeves of following sizes to correct line & level as per drawings within beams, slabs, walls, columns etc. Sleeves shall be duly sealed at ends with thermocol or any other material to make sure that no concrete enters & chocks the same during concreting. Also make clear that they are maintain to correct line & level during concreting, providing reinforcement around the sleeves as detail in the drawing.

Up to 50mm dia, Up to 150mm to 400mm length

Up to 80mm dia, Up to 150mm to 400mm length

Up to 100mm dia, Up to 150mm to 400mm length

Up to 150mm dia, Up to 250mm to 400mm length

Providing, fixing, jointing and testing heavy duty, UPVC pipes, - 6 kg/cm2 pressure, of approved makes, open, low density, to wall, ceiling and floor, approved quality, complete, for plinth WALL drain pipes and discharge pipes from drain channel , sumps including jointing with rubbering / solvent / solution and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material, including testing, cutting, making good the wall, ceiling and floor etc. complete of the following nominal bore (NB) size with Dual Check Backflow Preventers for piping from 15 mm to 75 mm dia:

Core cutting horizontal, vertical or inclined holes in reinforced cement concrete and / or hard rock/AAC Block or other masonry of following sizes for a max depth of 300 mm depth / length at all levels and locations as per directions of the Engineer incharge.

Upto 25mm dia

Above 25mm to 50mm dia

Above 50mm to 75mm dia

Providing and constructing AAC Light weight Block Masonry with 75mm/100mm/150mm/200mm/300mm thick at all levels in by using approved block laying polymer modified adhesive mortar or jointing compound recommended by the block manufacturer , including 75mm thick Patli / Stiffeners of M-15 Grade at approx. every 1000mm -1200mm with 2 nos 8mm steel bars all to be considered in the cost and no separate measurement will be done for steel and patli, also including scaffolding, racking out joints, curing with curing compound etc. in line, level and plumb, All complete as per specification for all height of floor or as directed etc. ( Rate includes the cost of stiffeners and steel ). (No holes for scaffolding will be permitted into the blockwork) ( Patli to be done for all the thickness of the blocks ) Work at all levels

Providing and constructing AAC concrete block masonry (approved make), blocks conforming to IS 2185 (Part-III) masonry using approved ready-mix mortar (approved make) as per manufacturer’s instruction, including providing RCC patli beam of 100mm at every 1.00m c/c with 2 nos. 8 mm dia Tor bars and 6 mm dia links at 300 c/c in cement concrete of mix M20, required formwork complete with raking out joints, curing, doing independent double legged scaffolding as per specifications etc. at heights, depths and leads as directed by Engineer incharge to his entire satisfaction. (Patli beam is part of the item)

a) 150mm thick wall

b) 100mm thick wall

Providing and applying 12mm thick plaster in cement mortar mix ratio CM 1:4 (1 cement : 4 sand) mixed with polypropylene fibers as per instruction of the approved manufacturer, to internal surfaces of concrete and masonry work; including raking out joints, hacking concrete surfaces and applying approved chemical bonding agent and applying a scratch coat over concrete surfaces by bonding / adhesive chemical coat as directed by approved manufacturer to create a key, cleaning / grooving deep junctions of concrete & masonry, grouting then back by mortar mixed with non shrinking compound along with packing of clean, fresh square cut aggregate; also providing and fixing 20 gauge GI chicken mesh @ 150 mm wide to junctions of concrete and masonry, preparing jambs, sills, grooves, pattas, wattas, rounding of corners, any circular works, ramps etc. all complete as per architectural drawings, specifications and finished smooth with wooden rundha etc. or as specified by the Engineer incharge at all leads, depth and lifts, doing independent double-legged scaffolding, cleaning of surfaces, curing, etc. complete as per specification and to the approval of the Engineer incharge.

Providing, preparing and plastering readymade proprietary Gypsum plaster to internal walls and ceilings average 13mm thick using Gyproc (universal) Elite plaster, wall surfaces of concrete, masonry work, including plaster mesh reinforcement of approved make and quality wherever required at junctions of masonry and concrete, doing jambs, sills, all types of groove as shown in the drawing, wattas, rounding of corners etc. all complete as per architectural drawing, specification and directed by Engineer incharge, at all lift, lead and depth, doing independent double legged scaffolding, making gypsum plaster mix as per approved manufacturer’s instruction, applying high grade polymer based bonding agent (Gyproc Bond IT) mixed with approved quality sand on RCC surfaces etc. complete as per manufacturer's specifications and approved by Engineer incharge. Plastering shall be to correct line, levels and plumb including curing, cleaning etc. complete to entire satisfaction of Engineer incharge.

Do as per above item but to walls / ceilings of ducts and inside the boxing masonry including adding approved waterproofing compound 2% by weight of cement or as directed by the Engineer incharge to his entire satisfaction. (Ducts)

Providing and applying minimum 25mm thick double coat cement sand plaster; first coat to be 15mm thick cement sand mortar of mix ratio CM 1:4 (1 cement : 4 sand) including adding 2% by weight of cement approved waterproofing compound and polypropylene fibers as per recommendations of approved manufacturer, second coat to be 10mm thick in cement sand mortar of mix ratio CM 1:3 (1 cement : 3 sand) including adding polypropylene fibers as per recommendations of approved manufacturer, finished sand face or as required to receive specified architectural external finish to correct line, plumb and level to external faces of walls, soffits/ceiling if any, including hacking concrete surfaces then applying chemical adhesive coating and a scratch/dash coat as a positive bond, curing the same, racking out junctions of masonry and concrete, then pointing and grouting using non-shrinking compound, joints grouted by pressing square crushed stone, further providing 150mm wide 20 gauge GI chicken mesh at junctions of concrete and masonry work, doing independent double legged scaffolding etc. Item also include plastering to preparing and finishing window sills, RCC cornices, making wattas, drip-moulds, pattas, grooves etc., doing curing, cleaning etc. all complete to the approval of the Engineer incharge.

Supplying, laying and fixing of std. chicken wire mesh IRCS-6(6 x 6 x 6/6) in positions at junctions of concrete & masonry works etc. all complete as per specification, drawing and instructions of engineer in charge. ( FOR RCC AND WALL EXTERNAL JUNCTION AREAS )

Chemical waterproofing to Toilet & Sunk area. Designing, providing and laying proprietary chemical water proofing system consisting of polymer modified acrylic base composite coating (of one part or two part component) as approved by the Engineer incharge and as recommended by the approved manufacturer of waterproofing coating, sandwiched fibre mesh and protective screed. The work shall include cleaning of surface, grouting porous surfaces including making ‘V’ grooves at junctions, cracks etc. Further including horizontal surface protected with 20mm screeding in 1:4 mortar (1 cement : 4 M sand) and vertical surface (wall) plastered with cement, sand mortar in ratio 1:4 (1 cement : 4 M sand), finished in ready to receive Architectural finish, in correct line, level and plumb, curing, grouting, testing, etc. all complete to entire satisfaction of the Engineer incharge, contractor to provide guarantee for 10 years on appropriate value stamp paper in approved proforma.

i) Location : Toilets

ii) Location : Drain

Providing and filling with cement mortar mixed in ratio 1:3:6 (1 cement : 3 M sand : 6 brick bats) including mixing of water proofing compound 4 % by weight of cement. Further surfaces shall be screeded with (1:1.5:3) cement concrete mix with 4% by weight of cement approved waterproofing compound about 20-30mm thick and finished smooth or ready to receive finish material as specified. Care shall be taken prior to filling all pipes passing through sunk portion are pressure tested by maintaining pressure for 24 hours and junctions of pipes passing through walls, slabs are well grouted and sealed. This shall be tested by ponding water for 100mm thickness and maintaining for 72 hours.

Providing & applying Waterproofing system of approved make to inside surfaces of the water retaining structures. (Water Retaining structures)- Providing and applying chemical injection treatment in the form of pressure grouting to leakage points, cold joints by injecting cement slurry mixed with approved expansive grout admixture @ 225 gms.per bag of cement, through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with Renderoc Plug and final cutting the projected nozzles and sealing off the PVC nozzles after the injection operation is over with Renderoc plug, nonshrink rapid setting mortar compound, finishing, curing etc. as per approved manufacturers specification and as directed. - Providing and applying at the junction of slab and vertical offsets with cement mortar 1:4 (1 cement : 4 mortar) and admixed with approved polymer bonding mortar additive at dosage of 1 Ltr per 50kg cement .- Providing and applying two coats of polymer modified cementitious elastomeric waterproof coating of approved make shall contain a liquid polymer component and a cementitious powder component, which shall be mixed as per manufacturer’s instructions and applied over prepared concrete surface as per coverage specified by the manufacturer.- Providing and applying plastering with CM 1:4 (1 cement : 4 sand) mixed with integral waterproofing compound (at the dosage of 125ml/bag of cement) to a minimum thickness of 12mm or as directed by PM.Tank shall be tested for leakage by filling the water and maintaining it for 72 hrs. Contractor shall provide 10 year guarantee for waterproofing on approved stamp paper in a approved proforma.

Providing and applying proprietary membrane waterproofing to Landscape areas through approved agencies consisting of

a) a) Surface preparation and injection grouting. RCC surfaces must be clean, even and sound concrete. Remove all oil, dirt, laitance and other contaminants by manually and surface shall be fairly smooth finish. Providing chemical injection treatment in the form of pressure grouting to leakage points, cold joints by injecting cement slurry mixed with approved expansive grout admixture @ 225 gms.per bag of cement, through the pre fixed PVC / aluminium nozzles in the 18 mm dia holes, fixing of PVC nozzles with Renderoc Plug and final cutting the projected nozzles and sealing off the PVC nozzles after the injection operation is over with Renderoc plug, nonshrink rapid setting mortar compound, finishing, curing etc. as per manufacturers specification and as directed.

Providing and applying two component approved elastomeric, seamless Polyurethane based membrane in two coats with spray / roller / brush application @ 1.7Kg/sqm to achieve thickness of 1.5mm, having an elongation capacity over 600% & Tensile strength over 6 Mpa, and with solid content more than 90% applied on the RCC surface, as per approved manufacturer's specification.

c) Providing and laying separation layer of 300 gsm non-woven geo-textile mat laid above membrane with an overlap of 50 mm and stitched at junctions

d) Providing and laying protection layer of M20 grade concrete screed and working out a smooth finish to protect the waterproofing membrane from mechanical damage. The screed shall have a minimum thickness of 50 mm at the lower end and shall be laid in slope of 1:100 as per the site requirement. The screed shall be cured by ponding it for a minimum of 7 days.

with use of approved products and work carried out as per approved shop drawings, instructions and specifications of the manufacturer of product. Also include required preparation of the surface, etc. testing by pounding water for 72 hours.

Providing and laying approved make quality, colour, design and shade fully homogeneous Vitrified tile (conforming IS 15622) flooring in pattern as detailed in drawing or as directed by the Engineer incharge. Tile to be bedded in cement sand mortar mix ratio 1:6 (1 cement : 6 sand) thickness as per detail drawing including cleaning and preparing the surface for bedding, spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading cement paste using minimum cement about 4.5 kg/sqm over bedding, joints to be cleaned and grouted with matching colour approved quality polymer based readymade compatible grout, curing, cleaning, protecting approved protection sheet till handing over etc. to required line, level, etc. all complete at all heights and leads to the entire satisfaction of the Engineer incharge. 600mm x 600mm size vitrified tile flooring.

Providing and laying approved make quality, colour, design and shade fully homogeneous Vitrified tile (conforming IS 15622) flooring in pattern as detailed in drawing or as directed by the Engineer incharge. Tiles fixed over well cured, prepared, cleaned concrete surface by using approved compatible tile adhesive (Bal or Laticrete or equivalent approved) to correct line, level and plumb, joints to be cleaned and grouted with matching colour approved quality polymer based readymade compatible grout, curing, cleaning, protecting approved protection sheet till handing over etc. to required line, level, etc. all complete at all heights and leads to the entire satisfaction of the Engineer incharge. but for 600mm x 600mm size industrial tile flooring. (Location : Store & Store room, pump room, Electrical AHU room)

Providing and laying polished Kota stone 18 mm to 20mm thk in flooring. Under bed shall average 30mm thk of 1 cement : 4 sand mortar by volume and brought to proper level. The kota stone slabs/tiles laid over under bed, pressed and tapped down with wooden mallet to the proper level, lifted and pressed again with thick cement slurry spread over the surface with fine joint finished including pigments, curing, grinding, granite polishing etc. all complete. (Over all laboratory room and passage area )

Providing and fixing 100mm high Tile (same tiles as that of flooring) skirting to walls/columns as shown in drawing or as directed by the Engineer incharge. Tiles fixed over plastered masonry / RCC surfaces by using approved compatible tile adhesive (Bal or Laticrete or equivalent approved) of required thickness to correct line, level and plumb. Joints are well cleaned and grouted with matching colour approved quality polymer based readymade grout and cured, cleaned and including finishing junction of plaster etc. all complete at all heights, lifts and leads to the entire satisfaction of the Engineer incharge.

i) 550mm x 450mm size kota skirting. (Location : staircase & rooms )

ii) Heavy duty anti skid vitrified tile skirting. (Location : Car wash equipment area)

Providing and fixing of approved make quality, colour, design and shade fully homogeneous Vitrified tile (confirming to IS 15622) dado to walls/columns, as shown in drawing or as directed by the Engineer incharge. Tile fixed with approved compatible adhesive (Bal or Laticrete or equivalent approved) over plaster to correct line, level and plumb. Joints are well cleaned and grouted with matching colour polymer based approved quality polymer based readymade grout and cured, cleaned, junctions with plaster finished smooth, etc. all complete at all heights and leads to the satisfaction of the Engineer incharge.

i) 600mm x 600mm size Vitrified tile dado. (Location : Gents, ladies Toilets)

ii) 600mm x 600mm size Vitrified tile dado. (Location : Other areas)

Providing & Fixing polished GRANITE STONE in stair case riser & steps with half round moulding with groove on every steps as per drg. including cement mortar 1:3 & in cement slurry, including necessary filing joints in cement pigmented to approved shade. Also includes necessary edge polishing, champhering, moulding etc complete as per the direction of architect. Below break up of dimension is subject to actual design and shall be considered approximate size of whole piece.

TREAD SIZE (1550mm *300mm )

RISER SIZE (1550 mm*165 mm )

TREAD SIZE (1800mm *300mm )

RISER SIZE (1800 mm*165 mm )

100mm high approved Granite stone skirting. (Location : Staircase)

Providing and fixing approved Granite stone jambs and soffit (in two steps) of shape and size of approved quality and colour with required moulding, chamfering / rounding edges, polishing etc. complete as per detailed drawing. Stone fixed with approved quality compatible adhesive ( approved make) back of stone to correct line, level and plumb. Joints well cleaned, grouted with matching colour approved quality polymer based ready-made grout and cured, polishing etc. Further to include required double legged independent scaffolding etc. all complete at all heights and lead to satisfaction of the Engineer incharge.

a) L shaped 100mm at front and 275mm inside lift jamb; Location: Lift opening

b) 230mm wide; Location: window sills (in 2 steps)

c) 100mm wide; Location: Toilet ledge wall sill

Providing and laying of 18mm thick machine cut, machine polished approved Black Granite stone Band / Threshold in pattern and size as detailed in drawing or as directed by the Engineer incharge. Stone to be bedded in cement sand mortar mix ratio 1:6 (1 cement : 6 sand) thickness as per detail drawing including cleaning and preparing the surface for bedding, spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading cement paste using minimum cement about 4.5 kg/sqm over bedding, joints to be cleaned and grouted with matching colour approved quality polymer based readymade compatible grout, curing, cleaning, protecting approved make protection sheet till handing over etc. to required line, level, etc. all complete at all heights and leads to the entire satisfaction of the Engineer incharge. i) 300mm wide (Location : Lift lobby) 150mm to 300mm wide as per the requirement

Providing & applying 1.2 mm thk PU based flooring which includes FLORPRIME quality WB Primer Coat, POLYDECK BC PU based base coat, Aggregate 30 broadcast & POLYDECK SF solvent free PU coating in desired colour shade.. (Location : over all lab area )

P/A Line Marking Paint : Providing & Applying Line marking paint 100mm wide using Flowcrete PU material.

Providing & laying 60 mm thick Precast standard interlocking heavy duty, M 35 grade paving blocks set by hand over the sand bed about 50mm thick, including levelling the original ground, compacting with compactor before & after laying the blocks by spreading fine sand by hand operated compactor, cleaning the surface all complete. (Location : Footpath SURROUNDING ROAD AREA AND PARKING AREA )

A) Providing & laying 75 mm to 100mm wide POLYDECK LM High build Epoxy based line marking over the flooring ( Ground - 1st floor)

B) Providing & laying 150 mm wide POLYDECK LM High build Epoxy based line marking & top coat with FLORTHANE UV - UV stable polyurethane based coating over the flooring (Terrace floor)

Providing and fixing Urinal partitions made out of 18mm thick approved granite stone urinal partitions machine cut and machine polished (both sides) in one piece and edges polished and semi rounded 500mm x 1050mm size (exposed size) stone fixed in wall securely and grouted and finished in cement sand mortar 1:3 (1 cement : 3 sand) fixed to correct line and level including chasing in wall, curing, cleaning, exposed edge of stone rounded / chamfered and polished etc. all complete as shown in the drawing and to the satisfaction of the Engineer incharge. (Location: Gents Toilet, Drivers toilet)

Providing, machine mixing and laying of 40-50mm thick vacuum dewatered (Tremix) concrete finished (with broom finish) of grade M20 of trap metal for plain cement concrete as per detail drawings including dewatering, steel form work, compaction, panels as specified and as per recommendation of manufacturer of equipment, power floating and broom finishing or finishing smooth as specified, cutting concrete for groove as expansion joint about 1/3rd depth of concrete and 12mm wide, filling grooves with approved bitumen based sealant, cleaning, curing surface etc. all complete to the entire satisfaction of the Engineer incharge. Further including applying of non-skid epoxy hardener as approved as per direction of approved manufacturer.

Providing, fabricating and fixing M.S. Railing 1200mm high out of 50mm dia & 5mm thick pipe section hand rail out of 'C' Class pipe, 50 x 50 x 5mm section in vertical spaced @ 1200mm C/C including M.S support & 25mm thick inclined spaced @250mm c/c, coated with iron oxide paint and finished with poly urethane paint with approved colour and make as per drawing out of square bars / class ‘C’ pipes / tees / angles / flats etc. including providing and fixing GI hold fast as necessary to the of RCC members / brick work, electric welding the joints and grinding smooth the welded joints to give one piece appearance including taking site measurements and preparing shop drawing, getting approval of shop drawing prior to fabrication all complete to entire satisfaction of the Engineer incharge. (Location : Staircase)

Providing, fabricating and fixing MS grill for service slabs (Shaft covering), made of 150 x 50 x 5 mm as primary member & 50mm x 50mm x 5mm as secondary member MS box section, MS net on top as per approved sample including cement concrete 1:2:4 block of required size, welding, priming with zinc rich primer etc. complete as directed. (Location : All floor Shafts)

ALUMINIUM COMPOSITE PANEL CLADDING (ACP)Designing, providing, fabricating and installing cladding of 4mm thick (0.5mm + 3mm + 0.5mm) aluminium composite panels with FR core of approved make, for sizes and panels (based on concept architectural elevation drawings) including required fixtures and fittings of stainless steel (SS 316 grade), anchor fasteners, jointing and sealing with M/s. Dow Corning silicon sealant, required fire stops, water drains and gutters and finishing junctions with concrete, stone, timber, aluminium, glass etc. all complete. Further include required preparation of shop drawings with structural calculations and getting approval from the Architect and structural consultants, providing samples, mock-ups, taking actual site measurements and modifying and coordinating with site and fabrication yard, all conforming to international standards etc. complete to the approval of Engineer incharge. Further the system installed and tested shall be guaranteed for 10 years in approved proforma on stamp paper of appropriate value. (Location at Roof decking area periphery)

Providing & fixing openable type trap doors in false ceiling in 19mm thick commercial ply with necessary wooden framework in CP teak including hinges, locking arrangements etc. Complete finished with 1.0 mm thk approved laminate or gypsum boarding as per instructions .

Providing & applying 1st quality Plaster of Paris (POP) Punning 12-15 mm thick over plaster surface to bring the surface in neat plumb, line & level and make it smooth, including making groove at junctions of dissimilar materials.

Providing and applying Oil paint (Enamel paint) of approved make and colour conforming to IS in two coats (surface and finish acceptable to the Engineer incharge must be achieved by the contractor and any additional coats if required shall be at the cost of the contractor); including preparing surfaces, filling up with gypsum or approved crack filler, binder; cleaning and making the surface dust-free, applying a sealer or primer coat of paint as recommended by approved paint manufacturer, applying two coats of paint (of approved make and shade), required scaffolding, cleaning and protecting till the handing over of site to the employer all complete to entire satisfaction of the Engineer incharge.

Providing and applying Plastic Acrylic emulsion paint of approved make and colour conforming to IS in two coats (surface and finish acceptable to the Engineer incharge must be achieved by the contractor and any additional coats if required shall be at the cost of the contractor); including preparing surfaces, filling up with gypsum or approved crack filler, binder; cleaning and making the surface dust-free, applying a sealer or primer coat of paint as recommended by approved paint manufacturer, applying two coats of paint (of approved make and shade), required scaffolding, cleaning and protecting till the handing over of site to the employer all complete to entire satisfaction of the Engineer incharge.

Providing and applying two or more coats of approved White wash (surface and finish acceptable to the Engineer incharge must be achieved by the Contractor and any additional coats if required shall be at the cost of the Contractor) including preparing surfaces, required scaffolding etc. all complete at all leads and lifts to entire satisfaction of the Engineer incharge.

Providing and applying Texture paint of approved make and colour conforming to IS in two coats (surface and finish acceptable to the Engineer incharge must be achieved by the contractor and any additional coats if required shall be at the cost of the contractor); including preparing surfaces, filling up with gypsum or approved crack filler, binder; cleaning and making the surface dust-free, applying a sealer or primer coat of paint as recommended by approved paint manufacturer, applying two coats of paint (of approved make and shade), required scaffolding, cleaning and protecting till the handing over of site to the employer all complete to entire satisfaction of the Engineer incharge.

Providing and applying minimum 6 mm thick silk finish plaster of paris over plastered surface as detailed above including making level beads, cutting, finishing and scrapping smooth to perfect line and level; including touching, finishing adjoining cornices, drips, corners, pattas, sills etc.; checked with 3 m aluminium edge and no undulation shall be permitted etc. all complete as directed and approved by the Engineer incharge at all locations marked in drawings.

Providing & applying 2 coats of Epoxy/PU paint application to specified areas, with necessary base preparation making surface clean, in perfect line & level filling all gaps, cracks etc, using approved shade, to ceiling, walls, columns, wooden, steel surface etc. Concrete as well as steel elements with appropriate base coat

TWO TRACK TWO SHUTTER SLIDING WINDOW: Providing,Supply, Fabrication & Installation of 27 mm approved make Domal series 2 track 2 shutter sliding window with 18mm thk DGU (5mm thk clear toughened glass + 8mm air gap + 5mm thk clear toughened glass) glass. Using double roller adjustable brearings, Wool pile, EPDM gsket & Lock. Aluminium sections shall be powder coated with 60 to 80 micron as per approved shade by architect / client. SIZE 1500 mm x 1400 mm approximate.

FIX WINDOW Providing,Supply, Fabrication & Installation of fix window, 52mm Z series with 18mm thk DGU (5mm thk clear toughened glass + 8mm air gap + 5mm thk clear toughened glass) glass. Using EPDM gasket & SS screws. Aluminium sections shall be powder coated with 60 to 80 micron as per approved shade by architect / client. SIZE 3650 mm x 2450 mm

ADJESTEBLE LOUVERS WINDOW: Providing, Supply, Fabrication & Installation of adjustable Louvers window with 4mm thk Frosted glass. Aluminium rectangular tube of 25x38 shall be fix to RCC / Wall with SS 304 Grade screw #8x50 with PVC sleeves. 4mm thk frosted glass will fix with aluminium adjustable louvers with clip. all Aluminium sections shall be powder coated with 60 to 80 micron as per approved shade by architect / client. SIZE 600 mm x 900 mm

SUN CONTROL FILM: providing and applying approved sun control film of 3M or Garware on existing glass window with approved shade and colour. etc complete as per architects instructions and details.

PLUMBING SYSTEM

Providing and fixing white vitreous china flat back type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

E.W.C.:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, level white P.V.C. flushing cistern with capacity as mentioned below, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. It should include 'P' or 'S' trap as per approved make with left or right vent in position including fixing it on chair brakcet or wall bracket. With necessary C.P. brass screws & plugs etc. Floor mounted EWC Universal with 5 to 7 Ltrs Cistern - white colour

Hand Spray wth PVC connection approved equivalent make (1M long) as per the instruction of engineer incharge.

2 Way Bib-Cock with connection for Health Faucet of approved make and as per the instruction of Engineer incharge.

Under Counter Sink including waste Coupling. WASH BASIN: Providing and fixing white vitreous china counter wash basin including making all connections but excluding the cost of fittings white colour angle back wash basin of size 630 X 450 mm

FANCY PILLAR TAP: Providing & fixing approved make heavy quality C.P. brass screw down pillar tap long nose not less than 810gm. with jam nut easy clean variety of 15 mm n.b. etc. complete all as directed by the Engineer-In-Charge

Providing and fixing Bottle trap with Wall Connection Pipes & Wall Flange weighing Not less than 263 gms. Extra if required. All as per the instruction of Engineer incharge.

Providing and fixing Fancy Angle Stop Cock including all fittings required to fix it as per the instruction of Engineer incharge.

Providing & fixing 100mm dia C.I heavy duty nahani trap as per the instruction of engineer incharge.

Providing and fixing Grab handle / Grab Bar of minimum 300mm length of approved make and design as per the instruction of Engineer incharge

TOWEL ROD: Providing & fixing approved C.P. brass towel rods of size 600mm x 20mm heavy duty with a pair of C.P. brass brackets wall flanges etc. fixed to wall with C.P. screwed on the raw plugs etc. complete as and when required and as directed by the Engineer-In-Charge.

Providing and fixing beveled edge mirror of superior glass (of approved quality) and of required shape and size with designer frame of approved make and complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Rectangular shape Rectangular shape 453x357 mm

Pressmatic Taps approved Make :Urinal Valve Auto Closing System with Built-in Control Cock with Wall Flange. Providing and fixing including removal of existing if any as per the instruction of EIC

S.S pipe clean out plugs with S.S. cap of following sizes for maintenance and cleaning purpose etc. complete as per directions of engineer-in-charge. (Optional in case require at site).75 mm dia.

HDPE/PVC clean out plugs with brass cap of following sizes for maintenance and cleaning purpose etc. complete as per directions of engineer-in-charge. (Optional in case require at site)

75 mm dia.

110 mm dia.

150 mm dia.

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 75mm

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 110mm

Forged brass Ball valve/butterfly valve (PN 10) with body of brass and ball & stem of Stainless Steel with material and labour etc all complete as per drawings, specifications and to the level of satisfraction of Site- Incharger

20 mm dia

25 mm dia

CPVC Pipes conforming to ASTM D-2846, SDR-11 grade and CPVC solvent weld fittings like elbows, tees, couplers, brass threaded adapters, insert ring etc. suitable for (domestic hot water) applications rated, concealed piping within wall / floor including jointing with fittings using solvent cement ,brass threaded end fittings for making connection to fixtures. The work shall also include chasing the walls with machine wherever required for concealed piping and making good the same after laying of pipes & necessary pressure testing Chasing finishing shall be done with 1:1 cement mixed mortar, restore the same original condition for internal and shaft piping, including necessary hot deep galvanized supports vertical / horizontal, as per direction of Site in charge direction. The rate shall include supply of S. S. screws and nut bolts etc. chasing in walls done by machine (CPVC PIPING )

20 mm Dia

25 mm Dia

65mm Dia

Sewage/ETP Inspection chamber with 230mm best quality approved Table Moulded bricks in CM 1:4 over a bed of 100mm thick PCC 1:4:8, internal walls plastered in CM 1:3 and external walls with CM 1:3 with sponge finish, benching and channelling in PCC 1:4:8,CI square frame & cover of size 900 x 600mm (weight 110 Kgs.), PVC steps in position as per the detailed drawing. The quoted rate shall also include necessary excavation and back filling etc. Clear internal size of the chamber shall be 900 x 450 mm. Depth of excavation and backfilling-1200mm deep as per the invert levels

Providing & laying including all necessary excavation in all strata, supply of material & labour & lowering, jointing RCC NP3 class (HUME) pipe of standard class including necessary ramming of subgrade after excavation to achieve a designed gradient & alignment by site rails & boning rods for proper levelling & making the joints water-tight with cement mortor 1:1 joints hemp yarn including 6" thick 1:3:6 C.C. bedding & encasement on all sides throughout length, excavation in all types of soils,refilling,curing etc. complete as per directions of engineer-in-charge including dewatering wherever necessary. - 300mm pipe

Public Address System

6W public area ceiling speakers complete with back box and with all the acccessories

Cabling work: Supply and laying of cables including fixing accessories, tray, trunking, conduits, saddles, clamps, ties, tags, termination of cables etc. Cable length and quantity are to be finally worked out by contractor at site based on actual measurements.Laying shall be inclusive of supply of wires, providing tray, trunking, galvanized steel tubes (conduit) / trunking, pull wires, tees / bends / elbows, junction Box / pull out boxes, etc., clamps / saddles for conduit clamping with all accessories & hardwares as required.

2C 1.5 sqmm FR Mylan Shielded copper , multistrand, twisted pairs, PVC armoured wires having fire retarded low smoke insulation.

Shielded Cat6 Cable for call station with RJ45 connectors.

6 zone call station with microphone

Fire Alarm System

Supply, installation, testing & commissioning of addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The shall include the thermal sensor. The detector shall have twin bi-colour LED for 360 deg viewing. The unit shall be complete with mounting all required mounting accessories. Designed to meet UL268, 7th Edition Approvals: UL Listed & FM Approved

Supply, installation, testing & commissioning of addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The shall include the thermal sensor. The detector shall have twin bi-colour LED for 360 deg viewing. The unit shall be complete with mounting all required mounting accessories. (with suitable mountings for above false ceiling appliaction) Designed to meet UL268, 7th Edition Approvals: UL Listed & FM Approved

Cable work: Supply and laying of cables including fixing accessories, tray, trunking, conduits, saddles, clamps, ties, tags, termination of cables etc. Cable length and quantity are to be finally worked out by contractor at site based on actual measurements.Laying shall be inclusive of supply of wires, providing tray, trunking, galvanized steel tubes (conduit) / trunking, pull wires, tees / bends / elbows, junction / pull out boxes, etc., clamps / saddles for conduit clamping with all accessories & hardwares as required. 2C x1.5 mm2 twisted FRLS armoured multistrand cable

FIXED DOME CAMERA Supply, Installation, Testing & Commissioning of Dome IR Color Indoor Day/Night, 6Megapixel CMOS , Pixel 1280(H)*960(V), 25/30 fps @720P, High speed, long distance realtime transmission , Day/Night and IR upto 30-40 mtrs, D-WDR, BLC, 2D-DNR , 2.8 to 12mm varifocal lens , Smart IR , Can connecto to Existing DVR and Any HD DVR, including power supply. Camera shall be suitable to install on wall / ceiling / Sheet panel.

Supply, Installation, Testing & Commissioning of IP Based NVR Watertight Bullet Camera. : • 6 Megapixel 1/3” CMOS Sensor in High Resolution, H.264/MJPEG Dual Codec & Streaming , 1920x1440@22fps /1080P (1920x1080@30fps), Digital Powerful WDR, 3D Noise Reduction, 2 Way Audio Supported.Up to 30 m IR range, 2.8 mm to 12 mm motorized vari-focal lens. • Intelligent Video Analytics, Micro SD Card Supported (SDHC up to 32GB), PoE Power Over Ethernet IEEE802.3af, CE, FCC Class A, RoHS, IP66, UL, ON/VIF Supported.

CAT-6-UTP ARMOURED VIDEO CABLE Supply & laying of armoured CAT-6-UTP Video cable with required accessories like cable tie, screws, raval plugs, saddles as per site requirement.

OPTICAL FIBER CABLE Supply & laying of armoured OFC cable with required accessories like cable tie, screws, raval plugs, saddles as per site requirement.

Access Control System

Design, Supply, Installation, Testing & Commissioning of Access control System c/w Panel, panel wiring, Programming Software, Testing & Commissioning to integrate with FA system. ( De-energize all magnetic locks in case of any emergency) Detail quantity, drawings & components require to installation on site to be work out by Vendor

Access Control system shall be inclusive of laying of wires, providing modular decorative plates (for mounting in Door Frame, suitable for clean room application) and heavy duty PVC conduits, pull wires, tees / bends / elbows, PVC junction /pull put boxes,bracket,backbox, clamps / saddles for conduit clamping, with all accessories and hardwares etc. Recessed conduiting shall mean chasing of wall / surface, fixing of conduit with saddles, openings for various boxes & plastering of same to match the rest of surface. Saddles shall be provided at not more than 300mm distance.

Specification for Biometric Reader which mentioned in below line item with requirment - Biometric + Mi-Fare / Equivalent Card reader ( for attendance) - Mi-Fare / Equivalent enabled IP65 & PoE. Fake Finger Detection, RISC 400MHz, 32bit CPU, User Capacity : 5,000, TCP/IP, Wiegand, RS485, RS232, PoE, Apprx. Dimension : 88(W) x 175(H) x 43.5(D) mm.

Single Leaf Door with Access control system controller with panel, power supply & internal wiring as required to make the system complete which includes and handle following devices - Biometric + Card Reader - 01Nos. - Exit Button (Non-Touch)(SS304) -01 - Emergency switch - (SS304)-01nos. - Magnetic Drop Bolt lock for single leaf door - 01 nos. - Magnetic Door Sensor -01 - etc.

Receipt Area

Ante Room ISO8

Primary Change Room

Single Leaf Door with Door Interlock System controller with panel which support for 2 no Doors,including power supply & internal wiring as required to make the system complete which includes and handle following devices - Entry / Exit Button (Non-Touch) (SS304) -30 - Emergency switch - (SS304)-30nos. - Magnetic Drop Bolt lock for single leaf door - 30 nos. - Magnetic Door Sensor -30 - etc.

2-DOOR INTERLOCK

Single Leaf Door with Access control Cum Door Interlock System controller with panel which support for 3 no Doors,including power supply & internal wiring as required to make the system complete which includes and handle following devices - Entry Button (Non-Touch) (SS304) -03 - Exit Button (Non-Touch) (SS304) -03 - Emergency switch - (SS304)-3nos. - Magnetic Drop Bolt lock for single leaf door - 03 nos. - Magnetic Door Sensor -03 - etc.

3 DOOR INTERLOCK

Specification for Card Reader which mentioned in below line item with requirment - Mi-Fare / Equivalent Card reader ( for attendance) - Mi-Fare / Equivalent enabled IP65 & PoE. Fake Finger Detection, RISC 400MHz, 32bit CPU, User Capacity :should be Expandable up to 10,000 card and transaction buffer of 25000, Ethernet TCP/IP protocal compatible with flash memory, Wiegand protocol, RS485, RS232, PoE, software& system should be enough access level and time zone level, 8/12 supervised inputs, 2 no. of relay input (FAS & Door interlock) & 4n. relay output with inbuilt digital power supply. Apprx. Dimension : 88(W) x 175(H) x 43.5(D) mm.

Mi-Fare / Equivalent cards with details printed on it like company logo, address, name etc.

Access control & attendance software with all rights with computer system with latest windows operating system, office licensed copy .Software should be 21CFR Part-11 compliant. Access control Desktop PC with the following minimum specifications: INTEL CORE i5, 3GHz, 4GB RAM, 500GB HDD, 32" LCD monitor, USB Mouse, USB keyboard, DVD / CD writer, modem/IP connectivity, HDMI output, configuration with Windows 10 pro, Office 12 and antivirus

Cable Work

Supply and laying of cables including fixing accessories, tray, trunking, conduits, saddles, clamps, ties, tags, termination of cables etc. Cable length and quantity are to be finally worked out by contractor at site based on actual measurements.Laying shall be inclusive of supply of wires, providing tray, trunking, galvanized steel tubes (conduit) / trunking, pull wires, tees / bends / elbows, junction / pull out boxes, etc., clamps / saddles for conduit clamping with all accessories & hardwares as required.

2C x 1.0 sqmm FR Mylan Shielded copper , multistrand, twisted pairs, PVC,non armoured wires having fire retarded low smoke insulation.

4C x 1.0 sqmm FR Mylan Shielded copper , multistrand, twisted pairs, PVC,non armoured wires having fire retarded low smoke insulation.

14 gauge, 25 mm Heavy duty PVC conduit

Cat 6 Cable

Cable Tray 150x50 mm (WXH),Cable tray- 2.0 mm thick,Type - Hot Dipped Galvanised Perforated Trays. Vendor shall supply tray joining plates, nut bolts, washers etc.

Cable Tray 50x25 mm (WXH),Cable tray- 2.0 mm thick,Type - Hot Dipped Galvanised Perforated Trays. Vendor shall supply tray joining plates, nut bolts, washers etc.

3 core 1.5 Sqmm power cable for ACS controller

Testing & Commissioning of Acess Control system

Clean Room Partition Work

Wall Panels – Progressive type SITC of Prefabricated factory made one-piece modular sandwich progressive panels, laminated with 0.8 mm cold rolled powder coated GI sheets on both sides with infill as PUF as core insulation material with density of minimum 40 kg/m³ for PUF and overall thickness of 80 mm. Minimum width of standard panel should be not less than or equal to 1185 mm, cost should include necessary panel to panel joining arrangement, necessary channels and flashings for fixing panels on the floor. GI profile along the periphery for reinforcement. U Floor Track suitable to accomodate epoxy floor flush with wall panel. The panels will be supplied in colour or as per client’s requirement, shade as per RAL codes and with peel off film. The peel off film will be removed after installation and all joints finished with silicon sealant application using masking tape. The modules will be smooth monolithic surfaces as well as being easy to clean and attractive. Glazing, doors, return air riser systems, process utility piping and electrical equipment shall be easily integrated in modules. Note:- There should not be any horizontal joint in wall panels of rooms irrespective of variable room height

SITC of Prefabricated factory made one-piece modular sandwich progressive panels, laminated with 0.8 mm cold rolled powder coated GI sheets on both sides with infill as PUF as core insulation material with density of minimum 40 kg/m³ for PUF and overall thickness of 35 mm. Minimum width of standard panel should be not less than or equal to 1185 mm, cost should include necessary panel to panel joining arrangement, necessary channels and flashings for fixing panels on the floor. GI profile along the periphery for reinforcement. U Floor Track suitable to accomodate epoxy floor flush with wall panel. The panels will be supplied in colour or as per client’s requirement, shade as per RAL codes and with peel off film. The peel off film will be removed after installation and all joints finished with silicon sealant application using masking tape. The modules will be smooth monolithic surfaces as well as being easy to clean and attractive. Glazing, doors, return air riser systems, process utility piping and electrical equipment shall be easily integrated in modules. Note:- There should not be any horizontal joint in wall panels of rooms irrespective of variable room height

Ceiling Panel-Walkable Type SITC of Non Progressive Prefabricated factory-made sandwich Ceiling panels laminated with 0.8 mm thick cold rolled powder coated GI sheets on both sides and with necessary flashings and suspension members for erecting the panels at desired levels. PUF insulation as core insulation material with density of minimum 40 kg/m³ for PUF and overall thickness of 50 mm approx., complete with panel to panel joining arrangement, necessary channels and flashings for fixing panels on the wall panels. GI Profile along the preiphery for panel reinforcement. Minimum width of standard panel should be not less than 980 mm. The panels will be supplied in color or as per client’s requirement shade as per RAL codes and with peel off film, the peel off film will be removed after installation and all joints finished with silicon sealant application using masking tape. Cost should include necessary suspension for ceiling, hanging arrangements, bolts, rods etc. Necessary cut-out for HVAC, light & other utilities will be covered with capping / flashing. (Load carrying capacity-250 kg/m2) All supports will be clamp type to suspension grid.

Coving

SITC of of 65 x 65 mm Aluminium Coving with polyester powder coated finish and air tight with sealant at wall to wall and wall to ceiling location. Colour of coving should match the colour of wall and ceiling panel. Note : In case of SS 304 panels coving wall to wall and wall to ceiling coving should be of SS 304.

Wall to Wall & Wall to ceiling

External vertical corner - 90°

3D corners

2D corners

Clean Room/civil Doors-Non flameproof

SITC of Clean Room/civil NON-FLAMEPROOF doors with 46mm thick honeycomb as infill with 0.8 mm thick PCGI Panels. Door frame 1.2 mm thick PCGI. Double glazed 6 mm thick toughened clear view glass (450mm X 600mm ) wherever required with 25 mm black border and both side adhesive tape and silicon sealant, door closer TS 68 Dorma make, drop seal, SS kick plate of 300 mm height and 0.8 mm thick, SS push plate on push side (Size: 125 x 325 (H x 1.2mm thick)), SS 'D' type handles on pull side with ϕ 19 mm x 254mm, single / double side key operated locking arrangement with 3 keys of Doyen Make, SS Ball Bearing Hinges, Silicon Gasket. Door colour: Client to confirm. Note: - 1. Consider Doors in Modular panel with service shaft on one side for Door interlock switch / access control 2. Drop seal should be easily detachable without dismantling the door to suffice maintenance / cleaning requirement. 3. Door dimensions mentioned are indicating clear opening.

Clean Room Doors

Single Door

800 x 2400/2200 mm Single Door

900 x 2400/2200 mm Single Door

1050 x 2400/2200 mm Single Door

Door Accessories

Automatic concealed door bottom Drop Seal (For Flush Floor)

Door Closer (Dorma TS-68) std arm.EN 7

One side S.S. D type handle (200 mm) & other side push plate

Door Lock (Dorset Make)

SS kick 0.8 mm thk plate 300mm Height

Civil Doors

Single Door

650 x 2400/2200 mm Single Door

900 x 2400/2200 mm Single Door

800 x 2400/2200 mm Single Door

1050 x 2400/2200 mm Single Door

Double Door

1200 x 2400/2200 mm Double Door.

Door Accessories

Automatic concealed door bottom Drop Seal (For Flush Floor)

Door Closer (Dorma TS-68) std arm.EN 7

One side S.S. D type handle (200 mm) & other side push plate

Door Lock (Dorset Make)

SS kick 0.8 mm thk plate 300mm Height

Vision Panel:

SITC of View panels should be factory assembled, flush to the wall on both side with double toughened factory made glass. Double Glazed Glass Panel with flush design with 6 mm thick toughened clear glass fixed in panel with 3M or equivalent make both side Adhesive Tape (black) over Aluminium polyester powder coated frame width to match wall thickness with silica gel desiccant arrangement and made air tight with Silicon sealant and all necessary arrangement. Sizes of the View panel for partition wall, the view panel size will be as per BOQ. Glazing will hold in place by extruded aluminium frame and silicon gasket and Food grade. Extruded aluminium frame thickness will vary as per single and double wall panel. View panel will be installed from the finished floor level as per the sill level mention in the Modular panel wall panel layouts / BOQ. (View panel/windows feature concealed anti-moisture agents). View panels should be furnished with the system to avoid condensation between two glasses. Note : View Panel width to match the standard panel width.

Double glazed View Panel in 80mm thk panel

1500x2100 mm (Emergency Crash Panel)

Inbuilt Return Air Riser

SITC of Modular Panels with Inbuilt risers will not be measured separately. They are measured in wall partition quantity. In wall partition inbuilt riser to be created. The return air riser will be fabricated from 20 G powder coated GI sheets capping on either side. The riser shall be provided with four side bevelled SS 304 Perforated Grill. Perforated sheet to be fixed on the wall panel by the magnetic locks (4-6 Nos). The magnetic locks are fixed to the riser frame with SS 304 screws. The perforated sheet will be supported on the wall panels itself. The bottom edge of the suction grill of return air riser will be 100 mm above the finished floor level. Necessary stiffeners / supports shall be provided within to avoid buckling of the riser panels. Riser duct should extend 200 mm above ceiling with 32 mm flange suitable for top / side connection.

SS 304 perforated sheet of 1.20 mm thick with 65% perforation area, magnetic latch arrangement,ceiling operated damper and 200 mm extended riser height above top side of the ceiling for duct connection with mating flange.

Supply and fixing for volume control damper inside the riser from room side 610x80

PVC Conduits & Boxes for fixing following

Cut-outs

Cutout Profiles for Terminal Box 300x300mm

Cutout Profiles for Terminal Box 450x450mm

Cutout Profiles for Diffuser 300x300mm

Cutout Profiles for Diffuser 450x450mm

Cutout Profiles for Diffuser 600x600mm

Cutout Profiles for Grill 300x300mm

Cutout Profiles for Grill 150x150mm

Cutout Profiles for Light Fixtures 300x300mm

Cutout Profiles for Light Fixtures 600x600mm

Cutout Profiles for Riser Grill size 500x450mm

Fire Sprinkler

Sprinkler/Hydrant System (Internal)

Providing, laying, jointing, testing and commissioning of G.I. `C' Class pipes (IS:1239 (Part-I)-1979) including cutting,threading welding etc providing all malleable galvanized iron fittings conforming to IS 1879, viz. Flanges, bends, tees, elbows,reducers, unions, supporting with G. I. clamps, hangers, M.S. brackets etc. including cutting holes and chases in brick or RCC wall / slabs and making good the same to the Approval of Architect / consultant,complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( INTERNAL FIRE FIGHTING SYTEM)

25 mm dia.

32 mm dia.

40 mm dia.

50 mm dia.

Providing , fixing testing and commissioning of pendant type sprinkler heads 68 deg. Temp.(K-5.6-Quick response type)

Providing & fixing testing and commissioning of UL Rated SS Flexible pipe-1.6MT long

Gun metal chrome finished Ball valves (PN 16) with fittings of screwedend type.

32 mm dia.

Butterfly Valves (PN 16) with CI Body, Black Nitrile Body Liner and Nylon Coated SG Iron Disc with material and labour including hydraulic testing etc. complete as per drawing, specification & to the level of satisfaction of Site- Incharge.

80 mm dia.

Flow switch on sprinkler distribution header on each floor with 2 SPDT contacts suitably rated, capable of the high pressure system and connected to fire alarm panel through cable. ( suitable connecivity to FA system)

80 mm dia.

STATUTORY APPROVAL -OR THIRD PARTY CONSULTANT

Sealing of fire shafts at all floor levels by using M.S. angle iron frame around the shaft, M.S. chequered plate and PCC of 1:2:4 (100mm thick) on the plate for whole shaft area.

Liasoning work with Statutory Authorities (CFO/etc.) for obtaining approval by preparing plans for submittal etc.incidental expenses connected with approval from Statutory Authorities (CFO) (All official fees/ deposits will be paid by Client)

Fire order signages for fire escape routs (LED type) with required all details as per statutory requirements

Note- 1) Contactor shall submit the hydraullic calculations /Shop drawings/revision required as per sites etc 2) Piping test with with 10 kg/cm2 pressure ( OR 2.5 times of design pressure) for 24 hours.3)Design validation by performing the functional tests with simulated fire condition in the space to be decided by the Client. The contractor shall supply all materials, labor and personnel , required for the functional test.

ELECTRICAL WORK

SECTION-I : PANELS & DB'S ELECTRICAL PANELS & DISTRIBUTION BOARDS: FABRICATED IN 14/16 SWG CRCA SHEET STEEL, POWDER COATED TO DESIRED SHADE. FULLY COMPARTMENTALIZED, SELF SUPPORTING TYPE.COMPLETE WITH BASE FRAME, KNOCK OUTS FOR CABLE GLANDS ETC.,ALL SWITCHGEARS, METERING, PROTECTION, INDICATIONS, TYPES Etc., :NOTE :Prospective Bidders to visit Site, Review existing Panels & DB's etc.Existing Panels andd DB's to be Refurbished appropriately as per this BOQ/ BOM :ALL SWITCHGEARS ABOVE 160A, SHALL HAVE MICRO-PROCESSOR BASED RELEASES UNLESS SPECIFICALLY DEFINED.MBR : MICRO-PROCESSOR BASED RELEASES FOR ( SC-OC-EF ).ALL SWITCHGEARS UPTO 160A, SHALL HAVE THERMAL MAGNETIC RELEASES UNLESS SPECIFICALLY DEFINED.TMR : THERMAL MAGNETIC RELEASES FOR ( SC-OC-EF )..

SUPPLY, INSTALLATION, TESTING & COMMISSIONING :Unloading, Shifting, Installation, Testing and Commissioning of following distribution boards. MCB distribution boards shall be totally enclosed with double door, vertical, surface/recessed mounting type, outer door shall be hinged type with push intype spring / magnetic lock, inner door shall be fixed up with screws with cut outs for MCB operation, copper bus bar of at adequate space for termination of incoming and outgoing cables,removable undrilled top & bottom gland plates, suitable for wall, column mounting type. he incoming MCCB shall be provided in separate compartment & shall have front drive mechanism and door interlock.The DB shall be fabricated out of 1.6 mm thick CRCA sheet steel . DB shall be completely wired up, up to incoming and outgoing terminals by PVC insulated flexible copper wire of adequaterating. All MCB in Power DB shall be suitable for Motive power (Curve C). Wherever standard DB's of DB manufacturers available, same shall be used. DB's shall be pre-wired and pre-assembled. Rate should be inclusive of the PPI kit, adaptor box for proper terminations of cables.

RPDB 2/Minor UT: 3Ph., 6 Way TPN-DB. Phase Segregated. ( LEGRAND/ HAGER/ SCHNEIDER Make.) I/C : 25A- TPN , MCB. O/Gs : 20A-DP-RCCB., 100mA. .. 3 Nos. ( R-Y-B).Phased O/Gs : C Curve type16A- SP-MCB's.. 12 Nos.Spare:- 2 Nos. First Floor

RPDB 2/Minor UT: 3Ph., 6 Way TPN-DB. Phase Segregated. ( LEGRAND/ HAGER/ SCHNEIDER Make.) I/C : 25A- TPN , MCB. O/Gs : 20A-DP-RCCB., 100mA. .. 3 Nos. ( R-Y-B).Phased O/Gs : C Curve type16A- SP-MCB's.. 12 Nos.Spare:- 2 Nos. Second Floor

LDB: 3 Ph., 8 Way TPN-DB. Phase Segregated. ( LEGRAND/ HAGER/ SCHNEIDER Make.)I/C : 16A- TPN , MCB,10KAO/Gs : 16A-DP-RCCB., 30mA. .. 3 Nos. ( R-Y-B).Phased O/Gs : C Curve type6A- SP-MCB's.. 09 Nos.SPARE:- 2 Nos. First Floor

LDB: 3 Ph., 8 Way TPN-DB. Phase Segregated. ( LEGRAND/ HAGER/ SCHNEIDER Make.)I/C : 16A- TPN , MCB,10KAO/Gs : 16A-DP-RCCB., 30mA. .. 3 Nos. ( R-Y-B).Phased O/Gs : C Curve type6A- SP-MCB's.. 09 Nos.SPARE:- 2 Nos. Second Floor

UPSDB/1-SPL-GF3Ph., 8/10 Way TPN-DB. Phase Segregated. ( LEGRAND/ HAGER/ SCHNEIDER Make.)I/C : 63A- TPN , MCB,10KA O/Gs : 63A-DP-RCCB., 100mA. .. 3 Nos. ( R-Y-B).Phased O/Gs : C Curve type16A- SP-MCB's.. 17 Nos.25A- SP-MCB's. 1 Nos. Spare 16A-SP-MCB-2 Nos First Floor

UPSDB/1-SPL-GF3Ph., 8/10 Way TPN-DB. Phase Segregated. ( LEGRAND/ HAGER/ SCHNEIDER Make.)I/C : 63A- TPN , MCB,10KAO/Gs : 63A-DP-RCCB., 100mA. .. 3 Nos. ( R-Y-B).Phased O/Gs : C Curve type16A- SP-MCB's.. 17 Nos.25A- SP-MCB's. 2 Nos. Spare 16A-SP-MCB-2 Nos Second Floor

ELDB3Ph., 4 Way TPN-DB. ( LEGRAND/ HAGER/ SCHNEIDER Make.)I/C : 25A- TPN , MCB,10KAO/Gs : 16A-DP-RCCB., 30mA. .. 3 Nos. ( R-Y-B).O/Gs : 6/10A- SP-MCB's.. 06 Nos. First Floor

ELDB3Ph., 4 Way TPN-DB. ( LEGRAND/ HAGER/ SCHNEIDER Make.)I/C : 25A- TPN , MCB,10KAO/Gs : 16A-DP-RCCB., 30mA. .. 3 Nos. ( R-Y-B).O/Gs : 6/10A- SP-MCB's.. 06 Nos. Second Floor

Providing Cables : XLPE-SWA-PVC : SUPPLY,INSTALLATION, TESTING & COMMISSIONING : Supply,Unloading, Laying, Testing and Commissioning of 1.1KV Grade XLPE/PVC FRLS insulated stranded copper conductor steel of armoured/unarmoured power cables as per the specs. Laying of Cables in horizontal/vertical formation on cable trays, supported along RCC/steel structures, pipe racks and cable supports provided, include unloading, shifting up to site at various location/levels, unpacking & inspection. The scope includes clamping of cables by readymade G.I. spacers, saddles, cable ties or clamps fabricated out of MS strip 3 mm thick along vertical runs and wherever specified, cutting of the cable as per actual measurement/cable schedule, Treasing and Clamping of Cable on cable tray, supply of all clamping materials and hardware etc., providing cable tags made out of aluminium strip and 75x20 mm in size with cable number and size punched on it. Cable tags shall be tied to cables at every 20 meter interval and at both the ends. Supports provided for clamping of cables up to individual motors and push-buttons shall be paid extra as per item rate for MS fabrication work.

Unused cables & Empty cable drums shall be returned to stores. In case of laying unlisted cables, rate of cable whose outer dia is closest to the cable sizes quoted shall be applicable. The same shall hold good for cable termination also. The rates quoted shall be for laying in trays, cable trenches (indoor and outdoor), pipes, along/on the wall/metallic partition etc.Contractor shall take exact measurement as per site feasibility & submit the required quantity to client. Any balance material left shall be taken back by the contractor free of cost, without any cost implication & no extra amount shall be paid for it. SUPPLY, XLPE Insulated etc. - COPPER /ALUMINIUM CONDUCTOR CABLES : 2XWY/2XFY : Sizes :

3.5c x 185 sq.mm. Aluminium-Conductor Armoured XLPE FRLS Cable.

4c x 10.0 sq.mm. Copper-Conductor Armoured XLPE FRLS Cable.

4c x 4.0 sq.mm. Copper-Conductor Armoured XLPE FRLS Cable.

SUPPLY, INSTALLATION, TESTING & COMMISSIONING : Providing Cable End Terminations : S,I, T & C : LT Termination : 1) Termination of XLPE/PVC insulated armoured cables (up to 11 kV grade) and connection of leads including the supply of cables glands and lugs & including cutting, stripping of cable insulation, drilling of gland plate, fixing of cable gland, crimping the lug on to the conductor, supply, fixing & marking with number ferrules etc. All necessary GI consumables & hardware, including all labour and materials complete as per approved drawings, directions of Engineer-In-Charge. The scope includes all standard tests, as specified. Scope will also include provision of additional supports, if required, with steel for proper dressing & support of cables as per approved drawings, specification and directions of Engineer-In-Charge.

2) Supply, installation of the terminations with double compression type Brass-Nickel cable gland, lugs & PVC Shrouds. The gland shall be provided with earth tag , ensures earth continuity between gland and equipment, etc. complete as required. XLPE Insulated etc. - COPPER /ALUMINIUM CONDUCTOR CABLES : 2XWY/2XFY : Sizes :

3.5c x 185 sq.mm. Aluminium-Conductor Armoured XLPE FRLS Cable.

4c x 10.0 sq.mm. Copper-Conductor Armoured XLPE FRLS Cable.

4c x 4.0 sq.mm. Copper-Conductor Armoured XLPE FRLS Cable.

SWITCH BOXES & SWITCH SOCKET :TABLE TOP/ WALL MOUNTING : ETC. : S, I, T & C : Supply, Installation, Testing and Commissioning of domestic(modular sockets) & industrial metal clad switch socket with "C" curve control MCB combination and "C" curve MCB enclosure for Non clean area, enclosed in (IP20) enclosure made out of 1.2 mm thick sheet steel enclosure, pre-treated and painted with two coats of primer and two coats of epoxy paint.(For Industrial sockets) The erection rates shall include fixing of enclosures on wall/concealed in the wall, supply of all fixing accessories/hardware, MCB and socket shall be wired up to outgoing terminals and termination including lugs, ferrules etc., complete as required.(Vendor to provide sample for each type of fitting at the time of GA Approval)

6/16A-Switch Socket outlets .

Non-FLP : SSO : 1 Switch -6/16A-Socket

Non-FLP : SSO : 2 Switch 6/16A-Socket

G. I. RACEWAY-CABLE TRAYS , ETC . : S, I, T & C : Supply, Installation in horizontal & vertical formation of prefabricated perforated / ladder type HOT dipped galvanized (not less than 65 microns) sheet steel cable trays different widths and delivered in standard lengths along with Coupler plates and requisite number of hardware, at different levels along pipe rack, ready made cable trenches, cable cellar, etc., in tier formation as per specifications, drawings, standard engineering practice and as per the direction of Engineer-In-Charge. The Contractor's scope is inclusive of lifting & placing of trays on supports at different levels, aligning, joining of trays with couplers, clamping / fastening of supports to the RCC/METALIC structure & clamping / fastening of cable tray to the support of the vertical portions and wherever required as per specs/ drawings.

All the necessary bends (horizontal / vertical), tees, cross, elbows, reducers, etc., as shown in the drawing and as per the site. Hardware is inclusive of this item. Hardware items (for fixing & aligning of cable tray) are all requisite material like Z-channel, threaded rod, nut, bolt, anchor fastener, screw etc. MS Structural supports are captured elsewhere in the BOQ. The supports should be as follows - For cable tray width from 50mm to 200mm - Z-channel of 50x50x4mm size with 2nos of 8mm rod at every 1.5mtr. For cable tray width from 300mm to 450mm - Z-channel of 50x50x6mm size with 2nos of 10mm rod at every 1.5mtr. For cable tray width from 600mm to 750mm - L angle of 50x50x5mm for both vertical & horizontal supports at every 2 mtr.

Condition / requirement are to be fabricated out of standard length of trays issued and as per standard and good engineering practice. Gas cutting of cable trays at site is not permitted. If any welding is to be done on cable trays applying of two coats of zinc rich primer and one coat of Silver paint at the modified / repaired area/ portions and erection of the same. Without limiting to the above, the work is to be completed in all respects end to end of each route as per the specs, drawings and the direction of the Engineer-In-Charge. Work for External cable tray like supporting pipe rack is under Mechanical / civil contractor scope. IS standard to be comprised - - IS 1079 / 2062 for sheet - IS 2629 / 4759 for Hot dipped galvanization

For Equipment Power Cabling :

100mm *50mm wide cable tray perforated type

300 mm*50mm wide cable tray perforated type

500 mm*75mm wide cable tray perforated type

Structural Supports for Cable tray

Supply, Installation & Fabrication of ISI mark GI structural steel in form of angles, channels, flats, Fabricated "C-Z-L" etc. for supporting various items of equipment such 'as various cable trays, push button stations,'junction boxes, light fittings, DB etc. including required hardwares

GI full threded Rod & Cable tray supporting & fixing clamps. Supply, Installation GI full treded rod with Nuts at both ends. 8 mm Thick with All Hardwears

LIGHT & POWER POINT CABLING/WIRINGS : Concealed wiring in HPVC conduits with Modular type Accessories. Point wiring shall include all necessary HPVC FRLS conduits with GI pull wire, conduit fittings, conduit accessories like saddles, spacers, bends, couplings, collars etc., junction / pull / inspection boxes, wires, gland, conduit supports, bushings lamp holders, ceiling rose, flexible conduit/ inspection L bends, fan hooks wherever required & terminations using tinned copper lugs of crimping type. A point wiring shall include in addition the earth continuity conductor/wire from the DB to the earth pin/stud of the outlets/switchbox & to the outlet point.

including cutting bending, threading, removing of burs & coupling as per specification, general engineering practice / standard, and std. Drawing and the direction of Engineer-In-Charge, to complete the work in all respect and to make ready the system to hand over for operation / utilization. The method of laying of conduit will be surface / concealed as per site requirement and as specified in drg. The scope of the work is including of fixing necessary spacing bars / saddle as specified, tying of the conduit with reinforced rods, chipping along the wall fixing chicken mesh and making good of the same as specified in drg / required at site. The detailed layout preparation for aesthetic look will be in contractor's scope.

Lighting Circuits Mains using : 3 Run x 2.5 sq.mm., FRLS Gr. PVC Insulated Copper Wire. This shall cover the wiring from SLDB to First switch board and looping of switch board to switch board. Switch board point Wire-2.5SQMM (Phase, Neutral) Wire 2.5Sqmm (Earthing)

Lighting Circuits including Primary Points , using : 3 Run x 2.5 sq.mm., FRLS Gr. PVC Insulated Copper WirePrimary Light point Wire-2.5SQMM (Phase, Neutral) Wire 2.5Sqmm (Earthing) in Mtr- Switch board to first Light fixture (Average Distance=10m)cables thru provided , Mesh Cable Trays, FRLS Gr. PVC Conduits , secured to walls,Ceiling, Trays etc.

Lighting Points , Looped or Secondary Points, using : 3C x 1.5 sq.mm., FRLS Gr. PVC Insulated Copper WireSecondary Light Point-1.5SQMM (Phase, Neutral) Wire 1.5Sqmm (Earthing) First Light fixture to subsequent light fixture 1 (Average Distance=5m)cables thru provided , Mesh Cable Trays, FRLS Gr. PVC Conduits , secured to walls,Ceiling, Trays etc.

Providing & Fixing of Switches & Sockets complete with accessories for recessed mounting. Supply of Modular switch boards with necessary number of modular box, SS front and rear plate, modular switches, switch sockets & blank plates. The module box shall be concealed in such a way that so front plate flush with wall, all civil work (chasing, chipping providing chicken mesh & plastering )includes in this item. Scope includes fixing of screw cover & marking identification numbers & interconnections as per standard drawing, site requirement & direction of Engineer-In-charge.

6 Amp Switch 1 nos. with 1 Module CRCA box and rear & front (SS 304 MATT finish) plate.

6 Amp Switch 2 nos. with 2 Module CRCA box and rear & front (SS 304 MATT finish) plate.

6 Amp Switch 3 nos. with 3 Module CRCA box and rear & front (SS 304 MATT finish) plate.

6 Amp Switch 4 nos. with 4 Module CRCA box and rear & front (SS 304 MATT finish) plate.

POWER CIRCUIT WIRINGS , USING PVC INSULATED, FRLS, 1.1KV. Gr. FLEX. COPPER CONDUCTOR CABLES. All socket point wiring shall be carried out using 1.5/2.5/4sq. mm copper stranded conductor 660/1100V grade PVC insulated FRLS wire including 25mm dia HPVC FRLS conduit. Circuiting from DB to first Socket & looping of socket shall be done using 3 runsx 1.5/2.5/4 Sq.mm FRLS Copper wires & covered in Primary & secondary socket point wiring.All socket point wiring shall be carried out using 2.5/4sq. mm copper stranded conductor 660/1100V grade PVC insulated FRLS wire including 25mm dia HPVC FRLS conduit. Circuiting from DB to first Socket & looping of socket shall be done using 3 runsx 1.5/2.5/4 Sq.mm FRLS Copper wires & covered in Primary & secondary socket point wiring. Power Circuits from DB to Power Outlets / Equipments using :

3 Run x 4.0 sq.mm. WireThis shall cover the wiring from DB to First socket/Equipment and looping of socket to socket using 4 SQMM wirePrimary Socket point Wire-4 SQMM (Phase, Neutral) Wire 4Sqmm (Earthing) - DB TO First Socket

4 Run x 2.5 sq.mm. WireThis shall cover the wiring from DB to First socket/Equipment and looping of socket to socket using 2.5 SQMM wireLIGHT FIXTURES & ACCESSORIES For Proper Installation Of The Same At Desired Locations. Suitable for Operation on 230V.AC. 50 hz. Power Supply.

SUPPLY,INSTALLATION, TESTING & COMMISSIONING : Supply, Unloading, Installation, Testing & Commissioning of standard light fittings and lighting accessories .The scope shall includes unpacking assembly of luminaries, providing of all hardware such as chain, nuts, anchor fasteners, bolts, screws, cleats, clamps, PVC insulated wires / cables from Junction box to lighting fixtures, ceiling roses ball and socket 'arrangement with J.B., suspension conduit pipe 1.5 m long 19 mm black MS conduit down rod for light fitting. The cost of fabrication supply and installation of MS supports with anchor fasteners will be the part of this item only. The scope of work also includes any modifications required to be carried out on the mounting bracket to suit mounting of light fixtures & any modification inside control gear box / fixture for proper commissioning of fixture.

NON Clean Room Fixture : 2' x 2': Recessed - 6000*/6500*K .. 60W. Recess mounted NON CLEAN ROOM LIGHT fixture with & milky Diffuser LC & grade Make Bayer etc. having fixture size approx of 600 x 600. The light fixture with bottom frame & 5 mm thk. thoughen glass. ( The color temp of LED lamp to be 6500 Kelvin. Cool Day Light ) System Efficay 120 Lm/watt.THD<10%,Surge Protection >3KV Constant Current driver,PF>0.95 LED .Light Fixture shall be made from CRCA powder coated bottom frame with minimum thickness 0.7mm or more duly epoxy powder coated.non-hygroscopic XLPE Gasket. CRI>70 with Threaded Type hanging arrangement Top Opening, luminair with accessories, suitable for : 60 W LED

NON Clean Room Fixture : 2' x 2': Recessed - 6000*/6500*K .. 40W . Recess mounted NON CLEAN ROOM LIGHT fixture with & milky Diffuser LC & grade Make Bayer etc. having fixture size approx of 600 x 600. The light fixture with bottom frame & 5 mm thk. thoughen glass. ( The color temp of LED lamp to be 6500 Kelvin. Cool Day Light ) System Efficay 120 Lm/watt.THD<10%,Surge Protection >3KV Constant Current driver,PF>0.95 LED .Light Fixture shall be made from CRCA powder coated bottom frame with minimum thickness 0.7mm or more duly epoxy powder coated.non-hygroscopic XLPE Gasket. CRI>70 with Threaded Type hanging arrangement Top Opening, luminair with accessories, suitable for : 40 W LED

Clean Room Fixture : 2' x 2': Surface Mounted- 6000*/6500*K .. 40W. Recess mounted CLEAN ROOM LIGHT fixture with & milky Diffuser LC & grade Make Bayer etc. having fixture size approx of 600 x 600. The light fixture with bottom frame & 5 mm thk. thoughen glass. ( The color temp of LED lamp to be 6500 Kelvin. Cool Day Light ) System Efficay 120 Lm/watt.THD<10%,Surge Protection >3KV Constant Current driver,PF>0.95 LED .Light Fixture shall be made from CRCA powder coated bottom frame with minimum thickness 0.7mm or more duly epoxy powder coated.non-hygroscopic XLPE Gasket. CRI>70 with Threaded Type hanging arrangement Top Opening, luminair with accessories, suitable for : 40 W LED

NON Clean Room Fixture : 1' x 1': Recessed - 6000*/6500*K .. 30W . Recess mounted NON CLEAN ROOM LIGHT fixture with & milky Diffuser LC & grade Make Bayer etc. having fixture size approx of 300 x 300. The light fixture with bottom frame & 5 mm thk. thoughen glass. ( The color temp of LED lamp to be 6500 Kelvin. Cool Day Light ) System Efficay 120 Lm/watt.THD<10%,Surge Protection >3KV Constant Current driver,PF>0.95 LED .Light Fixture shall be made from CRCA powder coated bottom frame with minimum thickness 0.7mm or more duly epoxy powder coated.non-hygroscopic XLPE Gasket. CRI>70 with Threaded Type hanging arrangement Top Opening, luminair with accessories, suitable for : 30 W LED

Recess mounted CLEAN ROOM LIGHT fixture with & milky Diffuser LC & grade Make Bayer etc. having fixture size approx of 300 x 300. The light fixture with bottom frame & 5 mm thk. thoughen glass. ( The color temp of LED lamp to be 6500 Kelvin. Cool Day Light ) System Efficay 120 Lm/watt.THD<10%,Surge Protection >3KV Constant Current driver,PF>0.95 LED .Light Fixture shall be made from CRCA powder coated bottom frame with minimum thickness 0.7mm or more duly epoxy powder coated.non-hygroscopic XLPE Gasket. CRI>70 with Threaded Type hanging arrangement Top Opening, luminair with accessories, suitable for : 30 W LED

Linear Lights -Recessed Linear Profile. IP20/6500*K ..20W (For OFFICE- MEETING ROOM). 1200 mm x 75 mm. 20W- LED Recessed mounted, Linear Lights, IP 20type light fitting with Acrylic Cover , with the accessories like ball sockets, down rod etc. ( The color temp of LED lamp to be 4000 Kelvin. for passages, Open Areas ) System Efficay 120 Lm/watt.THD<10%,Surge Protection >3KV Constant Current driverDriver, PF>0.95. Fixture shall be made from CRCA with minimum thickness 0.7mm or more duly epoxy powder coated.non-hygroscopic XLPE Gasket. CRI>70. (For OFFICE- MEETING ROOM)

2 x 18W Linear Light -Surface Mounted - 5700*/6500*K

Spot Lights -Recessed Round light. 4000K-6500*K .. (5W-9W) (For OFFICE- MEETING ROOM).

SURFACE MOUNTED (For Staircase area) LED PANEL LIGHT -600 x 600 40W - 6000*/6500*K

SURFACE MOUNTED (For Toilet area) LED PANEL LIGHT - 9'' x 9" 20W - 6000*/6500*K

40 watt LED Linear Light.-Surface Mounted (For Technical Area).

SAFETY SIGNS

General Warning

Electrical Hazard

Hot surface Hazard

Compressed Gas

Non-Flammable Gas

Entry

EARTH CONNECTIVITIES : Supply, laying of hot dipped galvanized (GI)/copper bare earth conductor bar / flexible wire /strip of following sizes along the cable trenches or cable trays or fixing to walls or structures or buried individually in paved/unpaved areas but excluding civil work finishing after layering of earthing strips etc. The installation shall include drilling of holes, connection & supply of adequate lugs, clamping, hardware material, Welded joints shall be used for G.I. strips. Welded joints after welding shall be painted with anticorrosive black bitumen paint , applying anti corrosive primer paint and two coat each of bituminous paint for buried earth strip. Excavation & backfilling of soil for burying the strip wherever applicable is paid extra as per the rate of excavation and backfilling rate. Jumper 150 mm x 50 mm shall be provided at every 10 meter interval for main earthing strip under instruction of engg. in charge and jumper rate is in inclusive.

32 x 6mm. G. I. Flat.

50 x 6mm. G. I. Flat.

HVAC WORK

LOW SIDE

Supply, Installation, Testing & Commissioning of AHU for NUDE mice, SCID mice experiment, Clean Corridor & food storage

Double skin Horizontal / Vertical Air Handling unit will be having following specifications

Construction

Thermal Bridging: TB2

Casing Strength: D1

Casing Leakage: L1

Thermal Transmittance: T3

Filter Bypass Leakage: F8

Material of Construction

Casing Details:

Outer skin 0.8MM thick pre coated GSS

Inner skin: 0.8mm Alu Zinc sheet

Framework: Extruded aluminum alloy

Drain Pan: Single skin 18 G Stainless steel with 13mm thick Nitrile rubber insulation with slope to avoid water retention

Insulation: Polyurethane foam

Panel thickness: 50mm

CHW & Coil details:

Coil casing blank off: Galvanized Steel sheet

Material of tube: Copper (Plain)

Tube dia: 12.7mm (0.5inch)

Thickness of tube:20guage

Header material: MS header with MS End connection

Fin material: 0.2mm Plain Aluminum with hydrophobic coating

Number of fins: 12FPI to 14 FPI

Filter details:

Make of filters: Thermadyne/ Freudenberg

Filter media: Synthetic non-woven for EU4 & EU7

Filter media: Submicronic glass fiber for EU13

Filter efficiency EU4: : 90% Efficient down to 10micron

Filter efficiency EU7: : 99% Efficient down to 3micron

Filter efficiency EU13: : 99.997% Efficient down to 0.3micron

Filter media: Submicronic glass fiber for EU13

Unit Configuration

1. Mixing box section with manually operated FA damper with EU-4 filters.

2. Pre Filter section with 50mm thick EU-4 + 300 mm thick EU-7 filters.

3. Pre cooling coil section with 6 row deep (12.7mm OD copper tube) CHW cooling coil with Hydrophilic coating

4. Cooling coil section with 8 row deep (12.7mm OD copper tube) CHW cooling coil with Hydrophilic coating

5. UV section with UV Light., Pureair make

6.Min. 2 pass SS Moisture Eliminator (Removable sliding type arrangement)

7. Electric Strip Heaters, ( Air flow sensor make:-honeywell/Siemens)

8. Fan section with Kruger Plug fan with TEFC sq. cage induction motors [Crompton/Havell/ABB) make IE3 IP 55 having antivibration isolators, anti microbial rexine connector at fan discharge.

9.Air flow switch [Siemens / Honeywell]

10.The fan section will have limit switch, marine lamp & view window

11. Fine filter section with 300mm thick EU-7 filter.

12. Supply air plenum with manually operated Al damper.

13. Canvas connection required for Fan and Connection for Supply & return duct from AHU to be included.

AHU-03-7000 CFM @ 130mmwc, 68.96 TR, 33.31 Kw Heater

AHU-04-7000 CFM @ 130mmwc, 68.96 TR, 33.31 Kw Heater

Supply, Installation, Testing & Commissioning of AHU Exhaust unit

Double skin Horizontal / Vertical AHU Exhaust unit will be Eurovent/AHRI certified and having following specifications

Construction

Thermal Bridging: TB2

Casing Strength: D1

Casing Leakage: L1

Thermal Transmittance: T3

Filter Bypass Leakage: F8

Material of Construction

Casing Details:

Outer skin 0.8MM thick pre coated GSS

Inner skin: 0.8mm Alu Zinc sheet

Framework: Extruded aluminum alloy

Insulation: Polyurethane foam

Panel thickness: 25mm

Filter details:

Make of filters: Thermadyne/ Freudenberg

Filter media: Synthetic non-woven for EU4

Filter media: Submicronic glass fiber for EU13

Filter efficiency EU4: : 90% Efficient down to 10micron

Filter efficiency EU13: : 99.997% Efficient down to 0.3micron

Unit Configuration

1. Return Air section with manually operated damper.

2. Pre Filter section with 50mm thick EU-4 filters.

3. Fan section with Kruger backward curve DIDW centrifugal fan with TEFC sq. cage induction motors 2Nos (1working +1 Standby) [Crompton/Havell/ABB) make IE3 IP 55 having belt drive, antivibration isolators, anti microbial rexine connector at fan discharge

4.Air flow switch [Siemens / Honeywell]

5.The fan section will have limit switch, marine lamp & view window

6. Fine filter section with 300mm thick EU-13 filter.

7. Exhaust air plenum with manually operated Al damper.

8. Canvas connection required for Fan and Connection for Supply & return duct from AHU to be included.

AHU-03,04-EX- 7000 CFM @ 75mmwc

Supply, Installation, Testing and Commissioning of Prefabricated Ducting in L types. ( Prefabricating Ducting means duct fabrication on CNC machines ) Ducting will have M.S. Angle Flanges with Food Grade Epoxy based primer, followed by Food Grade epoxy black colour, with Food Grade Rubber Gasket 5mm EPDM to be used between MS flange. All Ducting seam to be sealed with Food Grade RTV Sealent. All Necessary duct support are part of the Duct Installation. (The Site Fabrication ducting qty should not increase more than 10% of the total qty. ). All Ducting to prepared at factory in L type shape along with MS flanges.Aluminum Cladding to be provided for Exposed ducting. Leak testing of Supply and return duct as per DW-143 standard Leak testing Machine to have printing facility. Duct Construction shall be in compliance with relevant static norms as per SMACNA 2” Static pressure for Lab area & 3” Static Pressure for clean room area norms to be followed.

0.63 mm thick duct

0.81 mm thick duct

1.00 mm thick duct

19 mm thick - For Supply Duct

13 mm thick - For Return Duct

Supply installation of Fiber Glass or GlassWool acoustic insulation of minimum 1mm thickness to be provided inside duct to reduce noise.

Supply, Installation, Commissioning of removable core, Al. Epoxy Powder Coated Supply / Return Air Ceiling Diffusers of powder coated aluminum construction. Diffuser to be fixed in the 20swg GI plenum box along with powder coated volume control damper. The outer ring and the cores shall be 1 piece pressed type without any hair line crack.(The plenum box shall be measured in ducting quantity. The plenum box shall be of 100mm height.)

SqM. Rate of Diffuser

Supply, Installation, Commissioning of removable core, Al. Epoxy Powder Coated Supply / Return Air Ceiling grills of powder coated aluminum construction. Grill to be provided with powder coated volume control damper.

SqM Rate of Grilles

Supply, Installation, Commissioning of removable core, Al. Epoxy Powder Coated Supply / Return Air Ceiling grills of powder coated aluminum construction. Grill to be provided with powder coated volume control damper and inbuilt terminal heater and controller. The Terminal Heater to be along with the necessary cabling and accessories required with controller.

SqM Rate of Grilles

Supply, Installation,Testing, CommissioningExtruded Aluminum Low Leakage Aerofoil Design Volume Control Dampers suitable for Manual & Motorised operation for Filters & Risers (Suitable for Actuator installation at latter stage). Dampers should have percentage open marking, locking in position and sealing arrangement.

SqM Rate of Damper

Supply, Installation, Testing and Commissioning of UL listed Fire Dampers. Fire damper to be operated through Temp. sensor and / or Smoke sensor. The closing of the fire damper shall be through on/off type actuator along with controller and blade position indicator. (Fire Damper to be considered in Supply as well as return of AHU). Supply of smoke sensor in the scope of LV vendor.

Damper

Actuator

Magnehlic Guages - (-50 to +50mm) Range for Room to be installed in clean room partition cutout with SS 304 cover having brush finsih with High and Low Side Pressure Ports and Tubing. sensing Probe to be in ss 304 quality with SS 304 plate on Partition side to be part of the items.(Based on design the requirement might be positive or negative type.) Magnehelic guages installation to be inside wall, as per instruction provided by client.

Supply, Fabrication, Installation and Testing of Chilled Water manifold for AHU, manifold consists of

MS C Class Pipe with Fittings - 16RMT

Extended spindle Ball Valve / Butterfly valve- 5 Nos flanged End

2-Way Pressure Independent balancing & Control valve (PIBCV) with Actuator and all Accessories - 1 Nos Flanged end make-siemens

Y strainer with SS/Bronze mesh - 1 Nos Flanged End

Auto Air vent with 15mm ball valve - 1 Set

Drain Valve - 1 Nos 25 NB

4'' Dial Pressure Gauge 0-7kg/cm2 - 2 Nos With syphon and ball valve

Temperature Gauge with thermowell (range 0-100C) - 2 nos

Pipe Insulaton:32 mm thk Puf Insulation f Density Not less than 40Kg/m3.t The insulation shall be available in self-seal (pre-slit and pre-glued) pre-formed tube type for pipe diameter upto 4 inches. For pipe diameters above 4 inches factory-cut sheet insulation to match the pipe OD should be used. The Adhesive to be used as recommended by Manufacturer. The Application will be executed strictly as Specified by manufacturer. The Insulated Pipe shall be with 26 gauge aluminium Cladding.

U-Loop along with drain valve & Funnel to be supplied as part of manifold.

Factory manufactured Pipe section upto 80mm to be used for manifold insulation.

Manifold to be marked with arrows reflecting the direction of water flow for both supply and return along with system no.

The entire manifold assembly to be factory fabricated upto isolation valves.

Tentative Size of Manifold is given below final Manifold size will be as per manufacturerer requirement. Manifold to be as per AHU manufacturer requirement

Tapping required for the manifold will be part of the manifold irrespective of the length of tapping required.

Manifold upto 40 mm to be with Ball Valve and above 40 mm to be Butterfly Valve.

100 mm (FOR AHU-03 & AHU-04)

AHU Electrical Panel

Supply, Installation and Commissioning of Power Panel for AHU with MCCB - 4 pole (25 KVA Rating ) of Suitable Range as Isolator along with VFD and By Pass DOL / Star Delta Starter ( Upto 7.5 KW DOL starter above Star Delta). All VFD out put should have Contactors. The Panel will have Cooling Fan arrangement with Guard and Drawing Folder Provision. The Panel to be Fabricated from 16swg sheet duly powder coated of RAL Shade 7032, inlcuding Cabling from Control panel to AHU Motor, Exhaust Motor, UV light etc.Differential Pressure Transmitter compatible with Instrumented Inlet Ring at suction of blower to be provided along with control panel with control wiring upto VFD panel. Cabling from control panel to AHU will be in contractor scope irrespective of length of the cable required, Suitable control cabling to be considered. The Cables used should be Copper up to 10 sq.mm and Aluminum cable above 10 sq.mm. Armoured XLPE Cables to be used. The schematic drawing of Panel is indicated in the Tender. The Type of switch gear to be as per Client requirements. Thyristor based controller to be provided for heater control. Control Panel internal wiring to be carried out in 2.5 mm2 copper wires FR grade. Wires will be terminated to connector strip (Stud Type Connectors for Power Terminals) by using pin type lugs with Ferules. AHU/Ex/heaters/UV light etc. to have interlock wherever applicable. 20% additional potential free contact to be provided for BMS integration.Control Panel to be mounted on black powder coated MS stand. Electrical panel to have necessary controls for remote self Iluminating push button panel. AHU motor and exhaust motor to have VFD. Cabling from AHU to Control panel will be in contractor scope irrespective of length of the cable required.Suitable quantity of cabling to be included in the costing. Panel to be of IP54 rating. Indivisual Panel to be provided for indivisual AHU (Supply unit & Exhaust Unit)

AHU-03,04-SUPPLY MOTOR-10HP, HEATER- 44.65HP

AHU-03,04-EXHAUST MOTOR-5HP

Supply, Installation and Commissioning of AHU/Duct mounted dew point sensor along with cabling upto control panel. Sensor to be compatible with HVAC series VFD for controlling the actuators of Chilled water. Cabling from AHU to Control panel will be in contractor scope irrespective of length of the cable required.Suitable quantity of cabling to be included in the costing.

Supply, Installation and Commissioning of Duct Mounted Temp & RH Sensor for for controlling Hot water water modulating valve with cabling upto Control panel. Sensor to be compatible with HVAC series VFD for controlling the actuators of Hot water.Cabling from AHU to Control panel will be in contractor scope irrespective of length of the cable required.Suitable quantity of cabling to be included in the costing.

Supply installation testing and commissioning of microprocessor based PID controller to control Chilled water 2 way PIBC valve by taking feedback from temperature sensor and will control the VFD by taking feedback from Differential pressure transmitter. Control cabling required will be the part of control panel wiring. PID controller to match with the existing PID controller installed, All the PID controller to be of same make. Additional 4 I/o to provided in the PID controller, 20% additional potential free contact to be provided for BMS integration

PID FOR AHU-03,04

Supply and installation of following sizes of pre-fabricated Hot dipped GI perforated type cable tray along with coupler plates, 90 bends, Tees, necessary nut-bolts / washers and other hardware etc. including providing / fixing of necessary supports.

50mm (W) x 25mm (H) x 2mm (THK) cable trays

100mm (W) x 25mm (H) x 2mm (THK) cable trays

Supply and Installation of AHU condensate Drain Piping in Heavy Duty UPVC piping along with insulation of suitable thickness to avoide condensation and Clamps with rubber Pad packing on top and bottom side of pipe along with fitting accessories like bends, elbows, T's etc. duly supported at proper intervals. PVC pipe to be insulated with 32mm thick nitril rubber.

Supply, Installation, Testing, Commissioning of Eurovent/AHRI certified Double Skin Heat recovery wheel section with Al Thermal break profile and integral internal coving, double skin panels minimum 43±2 mm thick fabricated out pre-plasticized 22 swg GSS on outer side and plain 22 swg Galvanized sheet on inner side with Polyurethane foam insulation density not less than 43 kg/m3 sandwiched between inner and outer sheet for Process area.The Heat recovery wheel section shall comprise of Fresh Air Module with G-4 filter and Damper, Mixing Chamber for G-4 filter section with filters. Plate type Heat exchanger (Min. 70% sensible heat recovery).Heat recovery wheel section, belt drive packages with TEFC motor suitable for operation on 415 +/- 10% volts, 50 Hz, 3 phase, A.C. power supplyAll Dampers to be of Extruded Aluminum Low Leakage Aerofoil Volume Control Dampers with extanded shaft suitable for Manual & Motorised operation with % opening marking, locking and sealing arrangement. Control panel for Heat recovery wheel pump and other accessories to be with the unit, control wiring and necessary stand and support to be considered in costing.

FRESH AIR AHU-03,04--6616 CFM & EXHAUST AIR CFM--6088 (7000 CFM unit)

Supply, Instalation, Testing and Commissioning of Chilled water FCU Unit shall consist of CHW coil, fan, fan motor, coarse filters housed in a sheet metal casing complete with vibration isolators. The unit will have proper mounting arrangment. The Unit should consist of inbuilt controller to control the FCU unit with Temperature Sensor and its cabling. The FCU unit should include Manifold, Manifold to have Extended spindle Ball Valve / Butterfly valve- 5 Nos flanged End, 2-Way Pressure Independent balancing & Control valve (PIBCV) with Actuator and all Accessories - 1 Nos Flanged end , Y strainer with SS/Bronze mesh - 1 Nos Flanged End, Auto Air vent with 15mm ball valve - 1 Set, Drain Valve - 1 Nos 25 NB, 4'' Dial Pressure Gauge 0-7kg/cm2 - 2 Nos With syphon and ball valve, Temperature Gauge with thermowell (range 0-100C) - 2 nos, Pipe Insulaton:32 mm thk Puf Insulation f Density Not less than 40Kg/m3.t The insulation shall be available in self-seal (pre-slit and pre-glued) pre-formed tube type for pipe diameter upto 4 inches. For pipe diameters above 4 inches factory-cut sheet insulation to match the pipe OD should be used. The Adhesive to be used as recommended by Manufacturer. The Application will be executed strictly as Specified by manufacturer. The Insulated Pipe shall be with 26 gauge aluminium Cladding.U-Loop along with drain valve & Funnel to be supplied as part of manifold. Manifold to be marked with arrows reflecting the direction of water flow for both supply and return along with system no.The entire manifold assembly to be factory fabricated upto isolation valves. Temperature sensor and control panel required for FCU to be provided with the unit along with the stand for Electrical Paneal and necessary cabling and accessories required. (Cost of FCU unit shall include Electrical Panel, temperature sensor Chilled water manifold, Chilled water tapping and cabling irrespective of piping and cabling length required.)

1.50 TR FCU--- (UPS & BATTERY ROOM FF )

1.50 TR FCU--- (UPS & BATTERY ROOM SF )

Validation of HVAC System as per WHO TRS/ISO 14644 Guidelines Air Balancing, ACPH/Return CFM/Supply CFM/Fresh air CFM/Bleed CFM, HEPA integrity test, Particle count, Recovery test, Airflow pattern recording, Temp and RH Monitoring for Continuous 3 days with data loggers and any other test as per client requirement or as per guidelines. Vendor to follow the Clients protocol to carry out the validation of the Systems.Blow down of AHU will be part of validation scope. Lot should be for Total Area of Ground and first floor, in case of phase wise construction the Lot should be considered complete after final phase and that should be Ground and first floor completion.

1 set of inbuilt terminal heater and controller to be provided in spare, 2set of Belt to be provided where belt drive motor /main equipment has been provided with belt driven motor, 2 Nos of Spare PID controller to be provided of same make. All the filters including HEPA 1 set spare filters to be provided based on the AHU/Main equipment riser FCU etc.

SITC of Data logger to be provided for measure the temprature and RH as per instructed and as directed by OIC-ES.

SHAH EPC SERVICES AND PROJECTS PVT LTD (BID ID -3243448)

arcoma (BID ID -3248675)