SPL REPAIR TO BLDG NO P 17 ADM BLOCK OF 1861 MED REGT AT DINJAN MIL STN UNDER GE DINJAN

Amount

Dismantling of plain or corrugated sheeting all as specified and as directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and as directed.

S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws all as specified and as directed.

S&F for steel work in tubular section for purlin/rafters etc including special shaped washer etc. complete using induction butt welded tubes conforming to I.S. 1161-1998 grade St- 240 all as specified and as directed.

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc gde Fe-410 W (Gde E- 250) quality A all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets all as specified and as directed.

S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified and as directed.

M & L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing all as specified and as directed.

S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and as directed.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre all as specified and as directed.

M&L for 8mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) ® all as specified and as directed.

Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) all as specified and as directed.

Taking down of chaukhats or frame exc 1.5 Sqm but n.exc 4.5 Sqm (without taking off shutters from the frames) all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed.

S&F solid PVC moulded door frame of size 50mmx47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast all as specified and as directed.

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed.

S&F 75 mm size stainless steel butt hinges medium weight cold rolled all as specified and as directed.

Supply and fix for 150mm long aluminium handles, cast type, anodised complete all as specified and as directed.

Supply and fix in for 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed.

S&F 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides Ditto, but with particle board core all as specified and as directed.

S & F 35 mm thick, 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers all complete as specified and directed.

S & F 35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a) all as specified and as directed.

Supply and fix butt hinges 100mm long cold rolled medium weight complete all as specified and as directed.

Supply and fix 150mm long mild steel pressed handles, oval type, stove enameled black complete all as specified and as directed.

S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long all as specified and as directed.

S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 150mm long all as specified and as directed.

Supply and fix 250mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

M & L preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete as specified and directed.

S & F in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire & average width of aperature 1.18mm & fixed with tinned tacks are galvanized wire staples all as specified and as directed.

S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete as specified and directed.

S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes all as specified and as directed.

M & L MS flat iron work as in hold fast and similar small articles, cut to length, bent to shape, drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete as specified and directed.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165 all as specified and as directed.

S&F in Repair Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as specified and as directed.

S&F in repairs Stainless Steel drapery rod of 25 mm inner dia (in length as directed ) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beams including PVC curtain rings of matching colour @10 cm c/c all as specified and directed

M&L for preparation of old painted wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted wood and wood based surfaces of any description, n.exc 10 cm in width or girth when unconnected with other painting or when painted in different tint and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for two coats of synthetic enamel paint on new steel surfaces over one coat of red oxide primer over one coat of red oxide primer over 10cm width of grith including preparation of surfaces all as specified and as directed.

S&F powder coated aluminium anodised frame for doors, windows etc with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all all as specified and as directed.

S&F powder coated Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified.

S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including all necessary fittings like hinges joining cleats, glazing clips,moving roller, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

Supply & fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified and as directed.

Supply and fixing 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and as directed.

Supply and fixing 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and as directed.

Supply and fixing 5mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and as directed.

Dismantling timber scantlings 40 Sq. cm and over in section and in any position in unframed work as directed all as specified and as directed.

M&L 2nd class hardwood, scantlings, wrought, timber fixed, complete as specified and directed.

S & F 18/19mm pre-laminated particle board interior grade prelaminated both side with decorative choice lamination fixed with screws to timber frame work as in shutter of cup board and other similar work all as specified and as directed.

S & F Width of flaps (when open) 40mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed.

Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement : 2 Coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed.

Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:3) & painted with white or coloured paint complete all as specified and as directed

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises all as specified and as directed.

M & L 25 mm thick PCC type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in leveling all as specified and directed.

M&L for Vitrified Ceramic tiles(dark shade / double charged / ultra charged ) 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm as on vertical surfaces over 10 mm rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile Complete all as specified and directed.

M&L for Vitrified Ceramic tiles(dark shade / double charged / ultra charged ) 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed.

M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed.

M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed.

M&L Non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm 7mm thick coloured tiles in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over screed bedding 15mm thick in CM 1:4 as specified and as directed.

M&L for glazed ceramic tiles in vertical surface 300x450x7mm thick in dado over 10mm thick screed bed in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and as directed

Dismantling of stone slabs or tiles of any description or thickness as in floors, pavings, aprons, pathway etc laid dry or laid dry and pointed complete all as specified & directed.

M&L for 20mm thick granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite complete all as specified and directed.

Material and labour for Machine cut kota stone slab flooring 20 to 25mm thick size not less than 22" x 22" laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick cement screed bed in cement mortar 1:3 including rubbing and mirror polishing complete all as specified and as directed.

Material and labour for kota stone slab 20 to 25mm thick in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including cutting, moulding outer edges, rubbing and mirror polishing complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L fly ash brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with sub class 'B' bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:4) using old size bricks complete all as specified and as directed.

M&L for half thick brick work with sub class "B" bricks straight or curved on plan exceeding 6m mean radius with old size bricks locaaly available built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on brick walls/ concrete surface, etc. including raking out joints, hacking for key, scrubbing down with water, etc all as specified and as directed.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed.

M&L 15 mm thick cement plaster on wall in CM (1:6) on fair faces of brick work incl finished even and smooth without using extra cement all as specified and as directed.

M&L 15 mm thick cement plaster in CM (1:4) on wall ( with approved water proofing compound) on fair faces of brick work incl finished even and smooth without using extra cement all as specified and as directed. Note : 1. WPC @ 2% of cement, will be paid separately. 2. The rate quoted by contractor is deemed to be included necessary scaffolding and formwork as required upto 7.00 Mtr height building.

M & L 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceilings (sunshade, chajja etc) and finished the surfaces even and fair without using extra cement complete all as specified and directed.

Supply only Integral water proofing compound all as specified and as directed.

M&L for complete removal of exisiting treatment of wall and applying two coat of oil bound distemper over 1 to 1.5mm thick wall care putty and one coat of Primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 1 to 1.5mm thick wall care putty birla white or JK & over one coat of chalk whiting priming paint complete all as specified and as directed.

M&L for preparation of new plastered surface of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick plaster of paris putty on new surfaces complete all as specified and as directed.

M&L for complete removal of existing treatment incl preparation of old surfaces, scrubing down, washing etc from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfacesincl 1mm thick plaster of paris putty, using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and will execute the same work by authorised applicator as mentioned in PS and acessories complete all as specified and directed.

M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation all as specified and directed.

M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A’ all as specified and as directed.

Material and labour rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening etc. confirming to Fe 410-W (gde-E-250) quality-A and fixing complete all as specified and as directed.

S&F in repairs door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked), complete all as specified & as directed.

Supply and fix as in repairs rolled mild steel as in joist, channel, angle or tee section/hold fast/wind ties fixed independently with connecting base plate etc complete all as specified and as directed.

M&L PCC 1:3:6, C-1 (using 20 mm graded stone aggregate) as in bed blocks for inserting holdfast/ filling of steel frame, etc including necessary form work complete as specified and directed.

Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed.

Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed.

Refixing 15mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.)

S & F steel tubing 15mm bore medium grade galvanised with all fittings and fixed complete to wall, ceilings or laid in floors all as specified and directed.

Refixing 20mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.)

S & F steel tubing 20 mm bore medium grade galvanised with all fittings and fixed complete to wall, ceilings or laid in floors all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as directed.

S&F in repairs for MS grating CP 75/100mm dia, without hole and with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as directed.

S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S & F in repairs, stop valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions as specified and directed.

S&F in repairs 15mm bore Two way Angle valve chromium plated screwed plated screwed down,high pressure with capstan heads screwed both ends for iron pipe or for union all as specified and as directed.

S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends all as specified and as directed.

S&F in repair Hasp and staple, 75mm size, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified and as directed.

S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges all as specified and as directed.

S&F in repairs health faucet cast copper alloy with push button flexible steel pipe with PVC lining of 1 mtr long suitable for 15mm pipe all as specified and as directed.

S&F in repairs stainless steel peg set of 6 peg, 45 cm long, complete all as specified and as directed.

S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed

S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash hand basin 32/40mm dia, length not less than 70 cm, connected to PVC waste coupling/fittings complete all as specified and as directed.

Supply and fix in repair 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float, handle including Flush Pipe of polyethylene of low or high density or PVC 32 mm dia for low level cisterns and brackets after taking down old cistern all as specified and as directed.

S&F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.

S & F in repairs Vitreous china wash basin pedestal pattern, white,flat back, size 550 x 400 mm with brackets,excluding pillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (single piece WC with S trap), coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, CP jet nozzle, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified & directed.

S&F in repair for Vitreous China urinals, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing grating and Union for discharge pipe incl CP 40mm waste coupling and PVC 40mm waste pipe 900mm long all as specified and as directed.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) all as specified and as directed.

S & F 15 mm bore single lever faucet, cast copper alloy, chromium plated, fancy type with or without lettered Hot or Cold, screwed for iron pipe including iron pipe for hot and cold water all as specified and as directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long fixed on wall with PVC rawl & cadmium plated brass screws complete all as specified and as directed.

S&F glass corner shelf (Cat Part No T6010A1 of make – Parryware or equivalent from approved list of makes) complete all as specified & as directed.

S&F Towel ring CP (Cat Part No T6904A1 of make – Parryware or equivalent from approved list of makes) complete all as specified & as directed.

S&F in repairs Mirror cabinet PVC frame of size 400 x 500 mm fixed to wall with rawl plug & stainless steel suitable size screws complete all as specified and direceted.

S&F fixed in repair vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete all as specified and directed.

S & F 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed all as specified & as directed.

S&F as in repairs for Gun metal gate valves with iron wheel headscrewed both ends for iron pipes or for unions for 20 mm bore pipes, complete all as specified and directed.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a)Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L 25 thick cement concrete type B0 1:2:4 (12.5 mm graded aggregate) finished even and smooth. (c) Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight). (d) M&L for 20 mm thick screed bed in cement mortar 1:4 finished even and smooth. (e) Preparing & cleaning of fully dried cement plastered surface. (f) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384. (g) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (h) One coat of aluminium paint over APP membrane @0.11Kg/Sqm. Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

M&L for special treatment for sunken portion of WCs/Bath & toilet executed in following stage:- Stage1:- Demolition of wc including lime concrete and cemennt concrete etc and preparing of surfaces of existing sunken portion of wc`s or bath etc with wire brush to removed all loose dirts, oil grease etc including removing debries from site of work etc. Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 3:- Apply Dr. Fixit Premeseal primer or equivelent of STP Ltd (and allow to dry for 8 hrs) all as per manufacturer`s instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 micron or shilicry 215 of STP (The surfaces after painting one coats shall be allowed to dry for 6 hrs before next coats) Stage 5:- Rendering 10mm thick in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 6:- All CI joints shall be filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr. Fixit pidicrete URP all as per manufacturer`s instructions. Stage 7:- Making holes in walls and fixing 600mm long 40mm dia medium grade GI spouts for draining of excess water if any. Stage 8:- Carryout ponding testfor 48 hrs to ensure water tighteness of repaired sunken portion and filling of sunken portion for cement concrete Type E2, 1:5:10 using 40mm graded stone aggregate as in lean concrete complete all as specified and directed. Note:- only plan area shall be measured for payment under this items. (b) Depth of suken portion of WC`s/ bath shall be upto 35 CM which is to be taken into account while coating the rate against this item. (c) The rate shall be quoted by contractor shall be deemed to be included for all the horizontal and verticl treated surface of sunken portion of WC`s/baths.

S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F 0.71 mm thick Plain Aluminium sheeting alloy 31000H4 in ridges, hip, valley gutter, crumple joint etc. complete all as specified and directed.

M& L for PVC (SWR) floor trap 100 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

M& L for PVC (SWR) floor trap 75 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete all as specified and directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S & F Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges of thickness 1.25mm of dia 150mm complete all as specified & as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling of PCC & taking out old unserviceable 75mm bore PVC pipe with fittings & making good disturbed area complete all as specified & directed.

S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 110mm bore pipes complete all as specified and directed.

S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 75mm bore pipes complete all as specified and directed.

S & F for PVC (SWR) bends any radius with access door, 110mm bore complete all as specified and directed.

S & F for PVC (SWR) bends any radius, 110mm bore complete all as specified and directed.

S & F for PVC (SWR) vent cowl, 75mm bore complete all as specified and directed.

S & F for PVC (SWR) bends any radius, 75mm bore complete all as specified and directed.

S&F PVC(SWR) Vent cowl 110mm dia all as specified and directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed.

Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and keeping it in MES store for safe custody and refixing it after repair all as specified and directed.

Material and labour for point wiring for One light/exhaust fan point controlled by one,one way switch, with 1.5 Sqmm single core, PVC FRLS insulated unsheathed, multistranded copper conductor drawn through and including PVC concealed including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly suitable for modular sunken box with inner and outer cover for 01 module to 08 module as required at site complete all as specified and directed as below. Note:-(1) Rate for Cutting, chieseling and making good the existing surface for complete concealed wiring is deemed to be included in quoted rate all as specified and directed. (2) Rate include for Modular sunkan boxes, inner and outer cover.

Description all as per Ser item No. 147 here-in-before but One 3 Pin 5 Amps socket out let point on independent board.

Description all as per Ser item No. 147 here-in-before but One bell point controlled by one push button switch.

Description all as per Ser item No. 147 here-in-before but one 3 pin socket outlet, 5 Amp same board complete all as specified and directed.

Description all as per Ser item No. 147 here-in-before but using 2.5 sqmm PVC FRLS insulated copper condutor wire for connecting 15A socket on independent board complete all as specified/directed.

Description all as per Ser item No. 147 here-in-before but but with 4 sqmm.

Supply and fixing of modular switch one way 6 amps 1 module 240 Volts complete all as specifed/directed.

S&F of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB including all the fixtures for its installtion all complete as specified & directed.

Supply and fixing of modular socket outlet 2/3 pin 6 Amps 240 volts 2 module complete all as specified & directed.

Supply and fixing of modular socket outlet combined 2/3 pin 6 Amps 240 volts 2 module complete all as specified & directed.

Supply & fixing of modular switch one way 16 Amps 1 module 240 Volts complete all as specified & directed.

Supply and fixing of modular socket 6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

S&F modular bell push switch 6A 1 module all complete all as specified & directed.

Supply and fixing of surface mounting LED with minimum efficiency 100 LM/W edgelit slim round downlighter made of PDC AL with huge efficient LEDs and glare free opal diffuser, IP20 including all the accessories needed for its installation all complete all as specified & directed.

Supply and fixing of bell electric, ding dong type 240 Volts, single pole complete all as specified and directed.

Supply and fixing in repair of MCB Distribution board TPN double door 4 Way for mounting SPN/ SP/TPN/TP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed at site all as specified & directed.

Supply and fixing in repair of MCB Distribution board SPN 12 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified & directed.

Supply & fixing in repair MCCB 4 Pole, 415 V, fixed type,160 Amps with breaking capacity 36 KA with connection testing and commissioning including all the accessories needed for its installation all as specified & directed.

Supply & fixing in repair of MCB SPN 32-40 Amps 'B' Series 10 KA 240 volts complete all as specified/directed.

Supply & fixing in repair of MCB SP 6-32 Amps 'C' Series 10 KA, 240 volts complete all as specified & directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing and commissioning all all as specified & directed.

Supply & Fixing of ceiling fan step modular step regulator ,120W, 2 module all as specified & directed.

Supply and fixing angular/batten holder PVC/Polycarbonate suitable for batten fittings including one LED Lamp of 9W of Havells/Philips/Cromton Make, complete all as specified & directed.

S&F LED light fitting inverter type with high ouput diffuser 2 feet, 10 watts 220 volts AC decorative type with driver holder and LED lamp with aluminium housing including connecting up with three core flexible copper conductor cable of suitable of suitable size all as specified & directed.

Supply and fixing inverter type LED fitting 1x18 watts, 220volts AC decorative box type with driver,holder LED tube light conncting up to 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed.

Supply and fixing of recess mounted motion sencored LED flat panel 2 x 2 made of CRCA sheet steel housing duly powdercoated with high efficient LEDs & glare free full opal diffuser,including all the fittings required for installation, IP-20 including testing completed all as specified & directed.

Supply and fixing of ceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals complete all as specified & directed.

Supply and fixing LED Bldg light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with 40000 burning hour complete all as specified & directed.

S&F Bldg light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtr complete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed.

Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLS PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC conduit of adequate size fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLS PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 4 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old sub main wiring two run of 4 Sqmm cable one run of casing capping and one run of 2.5 Sqmm earth continuity wire for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed.

Taking down and Supply & Laying or Fixing or Passing through Pipe, XLPE insulated, Armoured, Electric Power UG Cable (Heavy Duty) with Aluminium Conductor, 1100 Volt Grade, Nominal Cross-Sectional Area 35 sqmm 3.5 core and Testing, including Brass Compression Cable Gland, Terminal Lug, etc including taking down complete all as specified and as directed.

Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, Taking Out and Laying of Cables, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed.

Removing excavated Materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the Starting Point in Soil, complete all as specified and as directed.

M&L Sand Cushioning (dry) in Trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed.

S&F LT cable cover , Type-1 flat-1 size 250 x 150 x 40mm for cable protection, laid breadth-wise along the axis of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed.

Boring under without disturbing the top surface of the road for passing through GI protection pipe 50mm bore, not exceeding 10m in single length complete all as specified and as directed. Note: Necessary infrastructure required for boring shall be arranged by the contractor at his own cost.

jitendra narayan goswami (BID ID -3406318)

M/S BORAH BROTHERS (BID ID -3406666)

M/S A K BROTHERS (BID ID -3406430)

CHETIA CONSTRUCTION (BID ID -3406728)