SPECIAL REPAIR TO 08 OR MD ACCN EOR 82 TO 92 AND EOR 113 TO 116 AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Dismantling wrought iron as in rafters, purlins etc or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - B] as in main and cross beams, hip and jack rafter, purlin, Gusset plate and base plates, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plate, framing for cladding, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

M&L for cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregates) as in copings, Chajja kerbs, roof kerb, roof padding, staging of water tank, for fixing of pipe in wall, for fixing of DB with wall etc including necessary formwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying 4mm thick APP modified water proofing polymeric membrane reinforced with non woven polyester fibre using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 4.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption,% - Not more than 0.15. (ix) Cold flexibility - (-) 50C. (x) Dimentional stability % change = Maximum 1%. (xi) Heat Resistance - Does not dirp at 1200 C

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

S & F 6mm thick Non-asbestos fibre cement building boards (6mm thick pre-painted designed type E-Board) to GI frame work with screws in ceiling (flat and/or slopping) and in jointless finish with & including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Note :- The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.

S&F of GI frame work for seamless ceiling comprising GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, Provision of Hangers 4 mm dia. G.I. (upto 1800mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of stone slabs, Paving Blocks and stone tiles of any description or thickness laid, bedded and pointed in any mortar as in floors, approaches etc including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc, complete all as specified and as directed.

M&L for 18 to 20mm thick machine cut, pre-polished Block Jet, premium quality, granite stone slab, in skirting, Kitchen platform, dado etc laid over and including 15mm thick CM 1:4 screed bed, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with the shade of granite stone including rounding / moulding the edges half round, complete all as specified and directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square / rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per item No 16 above but for vertical surfaces such as skirting, over and including 10mm thick backing coat in CM 1:4.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

M&L for coloured tiles of size 600mm X600mm x15 mm thick as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of the tiles including provision of 20mm screed in CM 1:4, complete all as specified and directed. Note : The tiles shall be of make JOHNSON ENDURA : METEOR series or equivalent of make AGL as approved by the GE.

M&L for coloured tiles of size 600mmX600mmX16 mm thick as in skirting,dado and risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of the tiles including provision of 15mm screed in CM 1:4, complete all as specified and directed. Note : The tiles shall be of make JOHNSON ENDURA : METEOR series or equivalent of make AGL as approved by the GE.

Demolition of cement concrete (un-reinforced ) of any description & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Taking down existing un-servicable waterproofing treatment from roof slab surfaces etc, cleaning the surfaces by wire brash and including disposing off the retrieved debris outside the premises / site, complete all as specified and as directed.

Surface exacavation n exec 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

M&L for 25mm thick sand cushioning including spreading and levelling etc, as in sub base of Floors etc,complete all as specified and directed.

M&L for 60mm thick Factory Fabricated Machine pressed precast conctete interlocking paver blocks confirming to IS 15658-2006, M-35 Grade (size, shape and colour as approved by the GE) with grey cement and pigment, complete all as specified and as directed.

M&L for factory fabricated Hydraulically machine pressed cement concrete chequered tiles of size 300x300X25mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM 1:4, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in CM 1:3 mixed with pigments to match the colour of the Tiles (in separate process), complete all as specified and directed.

M&L for providing 50mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not otherwise specifically provided for (above Ground Floor) including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat concrete surfaces, complete all as specified and as directed.

Use and waste of formwork to Beams, cantillevers, bressumers, lintels, shelves and similer items for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similer items including edges for rough finished flat surface of concrete, complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates ) as in Fins, fascias, louvres, parapets, and the railings exceeding 60cm in height and similar articles, complete all as specified and as directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates ) as in Beams, cantilevers, bressumers, lintels over 1.5 metre span, complete all as specified and directed.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates ) as in Chajjas, complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork with Sub-Class 'B', old size bricks of class designation 75 (average compressive strength 75 Kg/Cm2) straight or curved on plan exc 6m mean radius, built in Cement morter 1:6, complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:6) on the surfaces of brick work or concrete, finsihed even and smooth (without using extra cement), complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for rendering 10mm thick in CM 1:4 on the ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

M&L for preparing the new plastered ceiling surfaces and applying 3 coats of white wash, complete all as specified and as directed.

M&L for preparing new plastered surfaces of walls, applying two coats of Birla/Asian wall care Putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparing newely plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, also including disposing off the debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, also including disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down shutter of any description area exc 1.00 Sqm and not exc 2 Sqm each, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc and applying one shop coat of redoxide primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of fixing lugs, locks strike plate etc and applying one shop coat of redoxide primer, complete all as specified and as directed. Note:- Hinges shall be paid for seperately.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold fast block, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

S&F hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

S&F Factory made 35mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type on both sides including provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

S&F Factory made 25mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides icluding provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F factory made solid panelled PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet bedding and joined together with solvent cement etc complete all as shown on drg at Srl page No 156 of MES Schedule Part-II, as specified and as directed

S&F Factory made Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified, as shown on drawing and directed (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F standard aluminium powder coated section(minimum thickness of powder coating shall be 50micron and colour shall be as approved by the GE) as in frame, shutters for doors, windows / ventilators, partitions, kitchen cabinate, kitchen almirah, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered. (iii) Cost of all the items / accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and wire cloth shall be measured and paid separately under respective items.

S&F in repairs, Factory made, steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F 4mm thick sheet glass of ordinary quality and glazing for Aluminium Joinery or with & including oil putty for steel surrounds or with wooden beading for wooden joinery (cost of wooden beads included in wooden joinery), in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F 4mm thick Figured glass, pin head type and glazing for Aluminium Joinery or with & including oil putty for steel surrounds or with wooden beading for wooden joinery (cost of wooden beads included in wooden joinery), in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including stainles steel wire staples etc, complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt 200 mm long of extruded section, complete all as specified and as directed.

All as per item No 66 above, but 150 mm long.

All as per item No 66 above, but 100 mm long.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 100mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S & F 50mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and type C-21, complete all as specified and as directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

M&L for 18-19mm thick, prelaminated partical board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for cupboard shelves fixed with and including 2nd class hard wood supports of size as directed by the Engr-in-Charge with nails or screw as required at site, complete all as specified and as directed.

125mm size Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

M&L preparing new wooden surfaces of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and as directed.

Dismantling water tanks exc 500 litres but not exc 1000 litres capacity including disconnecting the connections, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 82 above but 20 mm bore.

Fixing only of 15mm bore GI tubing, medium grade with provn of new G.I. fittings as required and fixing accessories in new or old position (walls,ceiling, floor etc) including testing, complete all as specified and directed.

All as item No 84 herein before but 20mm bore.

S&F 15mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, fixed partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, also including cutting chases of the required size and making good the same after fixing of the pipes in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per item no 86 above but 20 mm bore pipes.

S&F Hard drawn steel wire fabric in available size weight not exc 4.00 Kg /sqm for the tank caging etc including welding, riveting, framing etc, complete all as specified and as directed.

S&F in repairs, vitreous china, 1st quality, squatting pan, Orrisa pattern of size 580 X 440mm, white with integral foot rests, 'P' or 'S' trap including making connection to trap, flush pipe, anti-syphonage pipe etc and also including provision of lime conctere bedding, complete all as specified and directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repair vitreous china wash basin, 1st quality, white, flat back, size 550x400 mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repairs Pillar taps, fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed.

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S&F in repairs stop valves /angle valves, fancy type, cast copper alloy, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repairs PVC connection of 450 mm length including brass nuts, complete all as specified and as directed.

S & F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete all as specified and as directed.

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints including fixing to 15mm bore steel pipe or union, complete all as specified and as directed.

S&F in repair sink made of 0.80 mm thick sheet of stainless steel grade A1S1304 for kitchen or laboratory with and including plugs, washers, wastes; brass chromium plated fittings, 40mm bore PVC waste pipe, also including bedding in cement mortar 1:3 on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S&F in repair grating doom 100mm dia of PTMT (minimum weightt 25 gm) for floor trap/nahani trap, complete all as specified and directed.

Taking down PVC SWR Pipes ( any size or pattern) including all fittings, heads, shoes etc, complete all as specified and as directed.

S & F 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, complete all as specified and directed. Note :- Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM 1:3 to match with the existing surfaces.

S&F uPVC vent cowl for 110mm bore uPVC (SWR) pipe with and including rubber ring joints, complete all as specified and directed.

S&F 110mm bore uPVC (SWR), junction single, (Single T) equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F 110mm bore uPVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

S&F in repairs 100 mm bore Cast iron soil, waste and vent pipes(spun pipes), in any length with ears, with and including cement joints, laid in trenches or in floors or fixed to wall vertically (also including suitable clamps for fixing of the pipes with the wall etc), complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid for separetly.

S&F 100 mm bore cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured), fitted with & including oval access door, complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 25mm bore (Minimum weight 455 grms), complete all as specified and as directed.

M&L for cement concrete 1:5:10 type E-2 (using 40mm granded brick aggregates) as in sunken portion of WC etc, complete all as specified and as directed

M&L for brushing neat cement slurry with 3.00 kilogram of cement per square metre over roof surfaces & sunken floors etc, providing 20 mm thick plastering in cement mortar 1:4 mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

M&L for applying evenly bituminous tack coat @1.20Kg/Sqm of industrial bitumen blinded with 0.006 cum of coarse sand per sqm on the surfaces of the sunken floor, complete all as specified and as directed.

Demolition and breaking up drain pipes 150mm bore (Salt glazed ware or AC pipes) set in cement mortar, complete all as specified and directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed.

Removing excavated material to a distance not exc 50.00 mtr and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregates for 150 mm bore pipes as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed.

M&L for 150 mm bore SGSW pipe, grade 'A', laid in trenches including jointing with cement mortar, complete all as specified and directed.

Disludging gully trap by taking out sludge & foreign materials, excavating a pit of appropriate size & depositing sludge in the pit and covering with 30 cm thick layer of soil to cover the sludge including removing surplus soil where directed by Engineer - in - Charge.

All as per item No 120 above but from the manholes of depth upto 100cm

M&L for complete removal of existing treatment of old decorated wall surfaces, applying two coat of Brila/Asian putty and thereafter applying two coat of oil bond distemper over one coat of primer, complete all as specified and directed.

M&L for complete removal of existing treatment of old decorated wall surfaces and applying two coat of cement base paint over one coat of primer after preparation of the surfaces, complete all as specified and directed.

S&F cast iron branch pieces, single (equal or unequal), oridinary or inverted (spigot or socket type) or with paralled branches for 100mm bore pipe with & including oval access door, complete all as specified and as directed.

M&L for applying two coats of white wash on old decorated surfaces of ceiling including preparation of the surfaces, complete all as specified and as directed.

S&F 150mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

S&F stainless steel kitchen plate rack of approx overall size 24’’ x 24”x10” , Cat No- P-310 of Make Prayag or any other equivalent as approved by GE.

S&F in repairs stainless steel decorative curtain rod of 20mm bore with wood finish, complete all as specified and as directed.

S&F brackets and funnel caps suitable for the curtain rod to be provided for item No 128 above, complete all as specified and as directed.

Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity) and making good the disturbed surfaces all as specified and as directed.

Taking down existing unserviceable submain wiring (including conduit /casing -caping), any size and making good the disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed.

Material and labour for point wiring for one light Point /one Fan point/one bell point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 133 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 133 here-in-before but for one socket with other switch/switch socket outlet 5 amps on the same board, complete all as specified and as directed.

All as per item No.133 here - in - before but for one light point controlled by two, 2- way switch.

All as per item No 133 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Supply and fixing switch socket out let multipurpose, 3 pin, 15 amp and one 3 pin, 5 amp, controlled by one switch, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 5 amps, complete all as specified and as directed.

Supply and fixing switch socket outlet 5 pin, 5 Amp, flush type, complete all as specified and as directed.

S&F socket outlet, 5 pin, 5 Amps, flush type, complete all as specified and as directed.

S&F switch, flush type, 5 Amps, SP, two way, complete all as specified and as directed.

S&F bell push, flush type, 5 Amps, complete all as specified and directed.

S&F call bell Dingdong type, AC, 230 Volts, single pole, complete all as specified and directed.

Supply and fixing ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

Supply and fix electronic fan regulator, flush type (Delux model), rotary step type, 5 step, not less than 100 watt, complete all as specified and directed.

Supply and fixing indoor LED 18/20 watt luminaires, Trim linea in a PC batten, compact appearance (with 4 Feet LED Tube light Luminaries), make Crompton : Cat No. LCTLN-20-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL's as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

Supply and fixing indoor LED 10 watt luminaires, Trim linea in a PC batten, compact appearance (with 2 Feet LED Tube light Luminaries), make Crompton : Cat No. LCTLN-10-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL'S as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

Supply and Fix Angular type lamp holder, PVC/Polycarbonate type with back plate, complete all as specified and directed.

Supply and Fix LED Lamp, 9 watt, retro fit, complete all as specified and directed.

Supply and fixing decorative wall mounting LED luminaries with end covers suitable for and including 1x15 watt LED lamp, Make Havells Model No City-01 or Equivalent model of make Bajaj/Phillips/CROMPTON as approved by the GE, including provision of copper conductor cable for connecion, complete all as specified and directed.

S & F 1X10W LED bulk head luminaries IP65, complete with all accessories, Make : Crompton, . Cat Part No - LBHP-10-CDL, or equivalent model of Philips/Bajaj/Havell's as approved by the GE, including provision of twin core fexible copper conductor cable of suitable size for connection, complete all as specified and directed.

S&F 20W LED STREET light luminaire, pressure die cast housing with polycarbonate cover and high power LEDs and secondary lenses with IP66 protecton, Make Crompton Cat No. LST-20-CDL-M/NL or equivalent of make BAJAJ/PHILIPS/HAVELLS as approved by the GE, complete with and including providing connection from ceiling rose with 3 core 1.5 Sqmm PVC insulated stranded copper conductor cable, also including providing bracket made of 25mm bore GI light grade tubing 1metre Long bent to angular Shape, (120 degree) with MS FI Clamps, nuts and bolts as required , complete all as specified and directed.

S&F in repairs ceiling fan, 5 star rating, 1200 mm sweep, 230V, SP, complete with accessories, MS hooke made out of mild steel flat iron of size 25 x 5mm of the rquired length for hanging of ceiling Fan, also making connection with and including copper conductor cable from eiling sose to fan, complete all as specified and as directed, Make : Usha model technix 5 star or Equivalent of make Havells/Bajaj as approved by the GE. Note : Old Fans shall be the property of the deptt and the same shall be deposited by the contractor in the MES store yard.

Taking down ceiling fan, sealing cable end, dismantling blades, painting with one coat of white synthetic enamel paint by spraying including filling cavities with filler after preparation of the surfaces, marking same MES No. with permanent Marker etc, hanging the ceiling fan and connecting up including provision of copper conductor cable from ceiling rose or connector to fan, complete all as specified and directed by the Engineer-in-charge.

S&F Exhaust fan, 300 mm sweep, 230 V, SP, metal body, heavy duty complete with and including accessories, luoversanchoring bolts, nuts, washers, making opening for fixing of the Exhaust Fan and making good the surfaces of the opening with CM 1:3 to match with the existing surfaces and provision of PVC copper conductor cable for making connection with ceiling rose, complete all as specified and as directed, Make : Usha Model No : TURBO-DBB-G or Equivalent of make Havells/Bajaj as approved by the GE.

S&F PVC, Heavy duty, exhaust fan of 250 mm sweep, single phase,230volts AC with louver shutter /grill accessories, mounting anchor fasteners, provision of three core 1:5 Sqmm copper conductor cable for connection, also including cutting opening for fixing of the Exhaust Fan and making good disturbed surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and directed.

S & F Geyser 25 ltr capacity, vertical type with BEE 5 star rating, having working pressure 8.0 Kg/cm2 (max), electric water heater with ABS cover outer body, 3mm EPAC (Engineered Polymer Anti Corrosion) coated inner tank to suit any kind of water, interchangeable colour panel, vitreous enamel coated Incoloy heating element for long life, adjustable capilary thermostat for temperature regulation, multifunctional safety valv, including Hot and cold water CP Flexible pipe etc and fixing along the wall all as specified and directed. (Make-Usha Model-Mysty or Equivalent model of V-Guard/ Racold/ Havells/Bajaj as approved by the GE).

Supply and fixing sheet metal enclosure for MCBs DBs, Double Door, phosphatised, Powder coated , Triple pole and Neutral (TPN), 240 Volts, 04 Ways, with and including 200 Amps rated bus bar, complete all as specified and as directed.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , Triple pole and neutral (TPN), 240 Volt , 8 Ways with and including 200 Amps rated bus bar, complete all as specified and directed.

S & F MCB, 'C' Series, Four Pole, 415 volts, 40 to 63 Amps, ruputring breaking capacity 10KA, complete all as specified and directed.

S&F MCB 'C' Series, SPN, 06 to 32 Amp, 240 Volts, reputring capacity 10 KA, complete all as specified and directed.

Supply and fixing MCB,Single Pole, C series, 10kA ruputring capacity, 6 to 32 Amps, 240 Volts, complete all as specified and as directed.

S & F MCB, 'C' series, single Pole, 'C' series, 10 KA ruputring capacity, 40 to 63 Amps, r240 Volts, complete all as specified and directed.

Supply and fixing AC Single phase Static Electronic KWH Energy Meter of accuracy class 1.0, 240V, 50 Hz, with Bakelite LCD Display of Rating 10-60 A with Transperent Hinged Type Box with six month History of Energy in KWH including taking down of old Energy Meter and depositing the same in MES store yard, complete all as specified and as directed.

Taking down of existing Under Ground cable from trenches/ along wall/pole etc, complete all as specified and directed. Note :- Excavation & Earth work shall be measured & paid for separately.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 6.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 6.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed. Note For Items No 167 & 168:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 20mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply, laying, jointing and testing XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm, 4 core laid in trenches/ along poles/ wall etc, complete all as specified and directed.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt Sub class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

Material and labour for galvanized iron tubing 40mm bore light grade with all fitting for protection of cable, laid in trenches/ along poles /wall/floor incl necessary clamps, bolts/nuts, complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid separately.

Dismantling of existing earthing and in lieu providing new earthing complete of advance encapsulated compound based (CPRI tested) maintenance free, pipe-in-pipe technology upgraded (Zinc & Alloy coated). Zinc coated (80-100) microns with pure zinc(99.9%) & alloy coating (200-250) microns. Earthing system shall be conforming to IS-3034, the outer and inner pipe shall be 76.2mm & 41.9mm dia, 2 metre length Zinc coated with additional special alloy coating 300mm on the topside for additional protection of the terminal annular space between the pipes being filled up with compact fill (CF) (Crystalline conductive compound). The compact fill (CF) mixture shall be machine pressed in the pipes and should not disintegrate or collapse when outer pipe corrodes. The inner pipe shall be extended with terminals for connectivity. The job includes digging the pits and refilling the same by electrodite/ conductolite back fill comopound (Ground Enhancer). The BFC shall be eco friendly, it shall not contain environmentally hazard materials having ROHS certification from NABL accredited lab. The earth pit shall also be provided with earth pit cover for protection and safe guard of terminals. In area where soil condition is bad, good earth shall be provided to fill the excavated pits by mixing the same with BFC, 4 bags (as per soil condition) extra per pit/unit. The earth electrode (the main component of the earthing system) which is in direct contact with the ground shall be able to provide a means of releasing or collecting earth leakage current. The materials shall have good electrical conductivity & anti-corrosion property in wide rage of soil condition and testing on completion including dismantling unserviceable earthing complete all as specified and as directed. Make ASHLOK Model- ASEEL or equivalent of make JMV/True Power as approved by the GE.

M/S JYOTI SHARMA AND SONS

M/S SEN CONSTRUCTION

T K GANGULY

GAYATRI BUIDERS

J.K.ROY & SONS

PRADIP KUMAR BOSE