PROVN OF COVER SHED FOR FOL DUMP AND DG SETS OF CSR, PROVN OF 02 X BUS SHELTER AT BATRA ENCALVE AND NAR BAHADUR THAPA ENCLAVE AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R I UNDER GE PANAGARH

Amount

M&L for excavating in post holes (or similar holes) each n.exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm, in soft/loose soil complete all as specified and as directed.

M&L for cement concrete type (D-2) 1:4:8 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete and as in post holes complete all as specified and as directed.

S&F Mild Steel work as in posts, struts, roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel, flat & hollow sections) including distance pieces, cleats etc. Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating @150 GSM GI based Corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges fixed with self tapping screws complete all as specified and as directed.

M&L for preparation surfaces of steel over 10 cm width or girth and apply of two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Excavating over areas, n.exc 1.5 m deep and getting out in soft/loose soils complete all as specified and as directed.

M&L for 200 mm thick Kankar or laterite,with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (i.e. 10% fly ash,30% clinker & 60% stone dust) laying in layers n.exc 30cm thick in each layer, watering, ramming and compacted with vibratory / power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engr-in-charge .

M&L for hardcore of broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed

M&L for 75mm thick PCC type D2, 1:4:8 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed

M&L for 100mm thick Cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in floors, finished even and smooth without using extra cement complete all as specified and as directed

M&L for forming Contraction (Dummy) joint 65 mm deep x10mm wide, filled with sealling compound Á (Cold applied polysuiphide/polyurethane joint sealant will be used) complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exc 6 mtr mean redious built in CM (1:6) complete all as specified and directed. Make : ACC/Shyam Steel Pvt Ltd/L&T/Lafarge

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

Supply only Liquid water proofing compound complete all as specified and directed. (Makes : Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

Returning, filling in and including spreading, leveling, watering & well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and directed.

Removing of excavated materials to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point in oft/loose soil complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 18.00 mentioned above 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

S&F roof trusses (framed) of angle iron members trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.of Fe-410- W(Gde- E - 250) quality B complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410-W (Gde E-250) quality A complete all as specified and directed..

S&F Pre-painted galvalume aluminum zinc coating @150 GSM GI based Plain steel as in ridges sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces of wall, surface finished even and smooth without using extra cement complete all as specified and directed

M&L for 150 mm thick in two layers of each 75 mm thick in pavings,with mix of fly ash ,clinker & stone dust in the proportion of 1:3:6 (i.e. 10% fly ash,30% clinker & 60% stone dust) laying in layers n.exc 15 cm thick, watering, ramming and compacted complete all as directed by Engr-in-charge .

M&L for 25 mm thick pre-polished coloured chequered cement concrete tiles of approved size, 30cm x 30cm thick set, jointed and pointed using with grey cement and pigment in floors, paving etc including the setting and jointing in neat cement paste and slurry 0.3 kg/Sqm over and including 20mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for 18-20 mm for granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for 75 mm thick Cement concrete type C1, 1:3:6 (using 20 mm graded stone aggregate) in plinth protections/ hard standing/sub base finishing the surface without extra cement even and smooth complete all as specified and directed

M&L for Machine pressed pre-polished precast concrete coloured interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigments complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including 20mm cement screed bed of CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces incl. necessary form work in cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc.as specified & directed by Engr-in-Charge

M&L for preparing new surfaces of walls plastered and white washing with three coats of white wash on walls complete all as specified and directed.

Excavation in trenches, n.exc 1.5m wide and n.exc. 1.5m in depth; for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc. n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed

S&F framed work such as grills, gratings,etc,with ends of bars shouldered and /or riveted, or forged into spickes; framed guard bars; barried iron door;ladders;framed balustars; walk ways; railings; framed work of water tans and similar work conforming to Fe-290 Gde-E-165 complete all as specified and directed

M&L for providing precast cement concrete louvres and jallies, type B0 1:2:4 (using 12.5mm graded stone aggregate), 35 mm thick (measured solid), including all mouldings but excluding frame (Pre cast frame shall be measured separately and paid for under item and set in CM (1:4) complete all as specified and directed

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement on walls in CM (1:4), using water proofing compound complete all as specified and directed.(Note: WPC shall be measured and paid separately)

M&L for finishing walls with two coats of cement based paint including preparation of newly plastered surface of concrete complete all as specified and directed.

M&L for fixing PVC (SWR) pipes of 110 mm bore diameter single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for cast- in- situ cement concrete in Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in lintels upto 1.5 m clear span, cills,steps and other similar bands, plinth courses,string courses and railings upto 60cm in height copings, apex stones,kerbs and the like including weathering, slightly rounded or chamfered angles and throating as desired complete all as directed by the Engr-in-charge.

M&L for 100mm thick PCC type D2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with CM (1:3) (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed

M&L for preparation of new surfaces of brick, stone, concrete and asbestos cement or plaster surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of cement primer complete all as specified and directed.

M&L for preparation ne surfaces of roof and applying two coats of Polyurethene (PU) acrylic based water proofing liquid compound (minimum 1.5 Ltr/sqm PU or manufacture instruction which are higher to be followed) over & including one coat of self priming primer @ one litre per ten sqm with reinforcing fabric sheet as per manufactures instruction to stop leakage/seepage from roof/wall complete all as specified and directed by the Engr-in-Charge. Notes: (i) As per description of theis item minimum two coats of Polyurethene (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out by as per manufacturer instruction. Please note no price adjustment shall be made, if as per manufacturer instructions more coats of Polyurethene(PU) acrylic based water proofing liquid compound & primer are required for roof treatment (ii) Quoted rate shall be deemed to be included for work in building/Structure of any height. (iii) Roof treatment to be carried out by authorised applicator.

M&L for rendering 5 mm thick in CM (1:3) on fair faces of brick work or concrete surfaces & finishing the surfaces even on ceilings complete all as specified and directed

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as specified and directed.

M&L for cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed for floor finishes complete all as specified and directed

S&F Bib tap long body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed. Make : Jaquar/Parryware/Hindware/Cera

S&F Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. Make : Jaquar/Parryware/Hindware/Cera

S&F CPVC pipes laid in floors/ trenches with outer dia 16 mm dia with all fittings and fixtures complete all as specified and directed.

S&F angle/stop valve cast copper chromium plated concealed with long shank type screwed down, high pressure with capstan head suitable for 15 mm bore complete all as specified and directed. Make : Jaquar/Parryware/Hindware/Cera

S&F grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed

M&L for glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including CM (1:3) back coat of mortar 10 mm thick for laying skirting/dado's wall tiles complete all as specified and directed. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvant cement, and S&F in the frame at side as per specification and drawing.

S&F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F anodised powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed

S&F sheet glass 4 mm thick , ordinary quality and glazing with rubber gasket in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F 100 mm size butt hinges extruded aluminium alloy with galavanised mild steel hing pin anodised and fixed type C-21 complete all as specified and directed

S&F 150 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150mm long complete all as specified and directed.

S&F vitreous china wash down water closet pan, pedestal pattern Pedestal pan and trap(excluding flushing cistern and flush pipe),connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device complete all as specified and directed Make : Jaquar/Parryware/Hindware/Cera

Supply and fixing 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and directed. Make : Jaquar/Parryware/Hindware/Cera

S&F vitreous china wash basin white, flat back, size 550X400 mm including cutting for pinning in ends of brackets, complete all as specified and directed Make : Jaquar/Parryware/Hindware/Cera

S&F CP tubular towel rail 20mm dia D type 60cm between two flanges complete all as specified and directed by Engineer -in-Charge. Make : Jaquar/Parryware/Hindware/Cera

Supply flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 32 mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms) suitable for basin/sink etc complete all as specified and directed

S&F toilet paper holder fixed to wall with chromium plated brass screws complete all as specified and directed Make : Jaquar/Parryware/Hindware/Cera

S&F soap dish, chromium plated, approximate size 160 x 160 x 90mm complete all as specified and directed Make : Jaquar/Parryware/Hindware/Cera

S&F PVC (SWR) floor trap 75mm dia of outlet plain with grating including jointing with solvent cement complete all as specified and directed

S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed.

S& F Vitreous China bowl urinal flat back Size of 465 x 355 x 265 mm white with grating and union for discharge pipe complete all as specified and directed. Make : Jaquar/Parryware/Hindware/Cera

S&F 32 mm bore waste coupling of PTMT (half or full threaded) suitable urinal. (Minimum weight 32mm-45gms/ 40mm-60 gms complete all as specified and directed

S&F Urinal Spreader of CP with 15 mm dia pipe complete all as specified and directed Make : Jaquar/Parryware/Hindware/Cera

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.2 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified Make : Jaquar/Parryware/Hindware/Cera

M&L for laying Reinforced concrete pipes 150 mm in dia, class NP2, laid and jointed complete with collars complete all as specified and directed .

M&L for Concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40mm graded stone aggregate complete all as specified and directed

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surfaces of concrete complete all as specified and directed. .

M&L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as speciified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed. .

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping) complete all as speciified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed.

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed. .

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as speciified and directed. .

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. .

M&L for rendering 15 mm thick cement plaster in CM (1:6) on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) incl WPC (WPC will be measured and paid separately).

M&L for rendering 10mm thick on fair faces on roof surfaces of concrete surfaces in CM (1:4) mixed with water proofing compound complete all as specified and directed. Note:-WPC measured and paid separately complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exc 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed. .

S&F Vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of lime concrete bedding, complete all as specified and directed. (Make : Hindware/Parryware/Cera

S&F 125 mm Brass Chromium Plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as directed by Engr-in-charge .

M&L for preparation of newly plastered surfaces of wall and applying a layer of plaster of paris putty of 1 mm thickness over plastered surface and two coat of oil bound distemper complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed. .

S&F Pipes galvanized, 20 mm bore “Medium grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

S&F gun metal , gate valve, 20 mm dia with iron wheel head, screwed both ends for iron pipe and fix complete all as specified and directed.

S&F capacity 750 Ltrs rotational moulded polyethylene water storage tanks (Cylindrical, vertical with closed top minimum three layer) confirming to relevent IS complete including provision of all inlet outlet overflow and drain pipe fitting complete all as specified and directed by Engineer in Charge Make : Vectus/Sintex/Prayag

S&F of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 20 mm dia with fly nut complete all as specified and directed. Make : Prayag /Polytrap

M&L for cutting existing steel tubing for alternation or addition of size 40 to 50 mm dia GI pipe complete all as specified and directed.

E/M PORTIOM Supply, laying, connecting, testing and commissioning of LT under ground cable XLPE insulated, aarmoured heavy duty electric cable with aluminium conductor , 1100 volts grade , crsectional area 10 sqmm 2 core complete all as specified and directed Note:-Excavation, sand cushioning, brick will be measured and paid separately.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . Note :- Punned thickness 18 cm shall only be considered for payment

Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed by the Engr-in-Charge.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement complete all as specified and directed.

Material and labour point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectional area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

Supply and fix switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.

S&F LED light fitting 1 x 20 watt box type with same make LED tube rod side connection AC decorative boxype 4' long wih driver, holder including LED tube connecting up with complete all accessories andconnection from ceiling rose with twin core twisted flexible copper conductor cable withsuitable size and earthing complete all as specified and directed.

S&F wall LED security light fittings 25 watt, 230 volts, minimum lumn output 100 lumen/watt, made up of pressure dia cast housing with prismatic polycarbonate diffuser and industrial LED with secondary optic and IP-65/66 including necessary connection complete with all accessories including connected with 3 core copper cable of suitable 1.5 sqmm size complete allas specified and directed.

S&F LED batten mirror light fitting 1 x 10 watt box type, Polycarbonate, cool day light, 6500K,1000 lumens with accessories complete all as specified and directed.

S&F ventilating exhaust fan 300 mm sweep 230 volt AC complete with louver and all accessories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size all as directed.

S&F epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral, 2 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.

S&F MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessary connection all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion.

M&L for wiring for socket out let on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectional area multistranded copper conductor , PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

All as per item No.115.00 above but 5 Amp socket on same board with other switches.

S&F switch 1 multipurpose 5 pin, (6 Amps) complete all as specified.

S&F Socket outlet 3 pin, 5/6A, flush type complete all as specified.

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), triple pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contact complete all as directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs including necessary connection complete all as specified and directed. (Note:Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SPN 40 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessary connection all as specified and directed (Note: Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F GI light grade 40mm dia of size for road cross/cutting on wall floor drain etc complete all as speciified and directed.

S&F 25mm bore GI tubing medium grade in trenches Floor/ Pillar connection in old or new position including fittings complete all as specified and directed.

All as per item No 123.00 above but 40 mm bore complete all as specified and directed.

S&F 25 mm bore dia pipe gun metal globle or gate valves, yoke type, full opening with iron whell head, screwed both ends heavy duty, ISI complete for iron pipes complete all as specified and directed.

S&F capacity of 1000 Ltr Rotation/Moulded Polyehtylene water tank (Cylindrical vertical with closed top minimum three layer) hoisted & fixed in position all as specified directed. Make : Prayag/Vectus/Sintex

S&F wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 3 star rating of capacity 2.00 TR complete all as specified and directed. Make: Blue Star/Carrier/Haier.

S&F copper wound wall mounted Voltage Stabilizer for automatic operation single phase naturally air cooled indoor type & designed for input variation between 130V to 270V with output Voltage Stabilizer at 220V to 240V with accuracy of + 2% and of capacity of 5 KVA complete all as specified and directed. Make: V-Guard, Sen & Pandit or eqvt.

M&L for wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core 4 Sqmm and one 4.0 Sqmm PVC insulated FRLSH cable with stranded copper conductor drawing into and including PVC Casing caping complete all as specified and as directed.

M&L for Sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core 6 Sqmm and one 6.0 Sqmm PVC insulated FRLSH cable with stranded copper conductor drawing into and including PVC Casing caping complete all as specified and as directed.

S&F epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral 240 V, 4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and as directed.

S&F switch socket combination 5 in 1, 5A/16A, flush type universal incl GI box complete all as specified and as directed.

S&F flexible water drain out pipe of suitable size for indoor splite AC unit complete all as specified and as directed.

S&F wall mounted Heavy duty Air conditioner outdoor unit AC stand upto 2 ton self bracket (Made by Iron with powder coatet painted) complete all as specified and as directed.

M/S GLOBE ENTERPRISE

M/S TRIVENI BUILDERS

ANSH CONSTRUCTION