WELCOME MAINT, PERIODICAL SERVICES AND REPAIRS TO WALL, FLOORING, PLASTERING, ROOF SHEET, FALSE CEILING, SANITARY, JOINERY ETC FOR TRIVENI COMPLEX, SANGAM COMPLEX, CORPS HQ, KLP QTRS AT RMS

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish of the premises complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry built in cement mortar ,complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks , straight or curved on plan exc 6 metre mean radius as in full brick thick walls built in CM 1:4 using old size bricks complete all as specified and as directed.

M&L for brick wrok with sub-class 'B' bricks, straight or curved on plan to any radius, built in CM (1:4) using old size bricks in half brick thick walls complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position, un -framed work complete all as directed.

Dismantling wooden boarding, any description, fixed in any position with nails complete all as directed.

S & F Second class hard wood timber scantling 40 Sqcm and over in section, in any position, clean sawn ,un -framed work, fixed with nails , complete all as specified and directed.

S & F for second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.

M&L second class hardwood plain fillets exc 13sqcm and not exc. 25sqcm, square or rectangular in section, wrought, secured with nails or brads complete all as specified and directed.

M&L for prelaminated particle board 12mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in pelmet boxes or in narrow widths not exceeding 15 cm each, rebated or flat edged including 6mm thick teak wood lipping allround complete all as specified and directed.

M&L for prelaminated particle board 18mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in shelves of cup boards etc., rebated or flat edged including 6mm thick teak wood lipping on exposed edge, supported on teak wood wrought fillet of size not less than 25x25mm on three sides complete all as specified and directed.

Taking down chowkats including shutter (without taking off shutter from the frame) area not exc 1.50 Sqm each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exceeding 1.50 Sqm and not exceeding 4 Sqm each and removing complete all as directed.

Taking down shutters of any description n.exc 1 Sqm each complete all as directed

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm eachcomplete all as directed

Taking down shutters for easing and adjusting area n.exe.1.00 Sqm and refixing in same opening complete all as directed.

Taking down shutters for easing and adjusting area exe.1.00 Sqm and not exceeding 2 Sqm each and refixing in same opening complete all as directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue and pinned at joints complete all as specified and as directed.

S&F for second class hardwood 30 mm thick plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for second class hardwood glazed and skeleton door shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F for second class hardwood glazed and skeleton window and ventilator shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. provided with stiles and rails, edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats complete all as specified and as directed.

S & F for 30 mm thick flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F factory made 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative choice sunmica lamination 0.9mm thick type I with lipping to match fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening complete all as specified and as directed.

S&F for Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame wedded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and as directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section of size 40 x 18 x 1.29mm thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed

S&F for anodised aluminium door shutter, aluminium section weighting 0.55 kg/m including necessary joining, cleats,glazing clips,rubbber neoprene, packing headls 2 nos in each door hinges anodised aluminium snap beading screw etc.complete all as specified and directed

Cutting holes in brick walls, built in cement mortar for taking out or Inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1as required in exc. half brick but not exc. one brick thick walls, complete all as specified and as directed.

S&F for mild steel conforming to Fe 410-0 or Fe 310-0 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; hand made sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles complete as specified and directed.

M&L Second class hard wood small fittings such as brackets of any type, shaped door and window stopers and the like, including all necessary labours, articles not exceeding 200 cu. cm each complete as specified and directed.

M&L for preparing surface of wood and wood based matreials, new or old, of any description and girth and treaed with tar or coal tar black paint and sanding newly tarred surfaces with clean sharp sand complete as specified and directed.

M&L for preparing surfaces of small articles such as holdfast etc. of steel or iron, new or old, area not exceeding 0.1 Sqm each and treating with tar or coal tar black paint complete as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 50mm size complete as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 75mm size complete as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete as specified and directed.

S&F 300mm ordinary mild steel rat tail rod patttern springs includding roller and roller plate complete as specified and directed.

S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section and fixed complete as specified and directed.

S&F Aluminium, anodised, barrel tower bolt 150mm long of extruded section and fixed complete as specified and directed.

S&F 40 mm cupboards knobs fixed with nut screw and washer of brass polished complete as specified and directed.

S&F for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete as specified and directed.

S&F Extruded aluminum alloy handles, fabricated type, anodised 100 mm size complete as specified and directed.

S&F in repairs Mortice lock,vertical type Brass 2 levers, size 100 mm,complete as specified and directed.

S&F Extruded aluminum alloy handles, fabricated type, anodised 150 mm size complete as specified and directed.

S&F Hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws 100mm size complete as specified and directed.

S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. fixed in repairs complete as specified and directed.

S&F for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg , fixed in repairs,complete all as specified and directed.

S&F in repair floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete as specified and directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless cover, governing pivot made of brass, other parts made of mild steel heavy duty , fixed in repair ,complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete as specified and directed..

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples fixed in repairs, complete as specified and directed..

Dismantling structural steel work including doors, gates but excluding framed truss etc, complete as directed.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410-W (Gde E- 250) quality A complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410-W (GdeE- 250) quality A complete all as specified and directed.

S&F steel works in tubular truses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1797 grade St 240 complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings,complete all as directed.

Dismantling Asbestos cement (corrugate ted, semi corrugated, etc.) sheets in roof coverings including ridge or similar pattern roof coverings complete all as directed.

S & F 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with 'L' hooks or cranked bolts complete all as specified and directed.

S&F 6mm thick asbestos cement two piece adjustable serrated ridge for corrugated or semi corrugated sheets fixed with ‘L’ hooks or ‘J’ type cranked bolts complete all as specified and as directed.

S&F for 0.63mm galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 275, fixed with L-type or J-type or cranked hook bolts complete all as specified and directed.

S&F Plain Galvanised Mild Steel Sheeting 0.80mm thick Galvanised as in Ridges, Hips Valley, Gutters and Straight Flushing, fixed with GI 'L' type or 'J' type or cranked hook bolts in roof, with grade of zinc coating as per IS complete all as specified and as directed.

S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour as approved of 550 Mpa tensile strength as in roof covering/ cladding to wall etc. fixed with self tapping screws complete as specified and directed

S&F 0.50 mm thick Prepainted galvalume aluminium zinc coating GI based plain steel sheet any colour as approved of 550 Mpa tensile strength as in ridges etc fixed with self drilling and self tapping screws, complete all as specified and directed.

Dismantling of wall and Ceiling Board of any description and any thickness including Cover Fillets, , complete all as specified and as directed.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified and directed.

S&F for 4 mm thick veneered decorative Plywood (no of ply 05), grade-I (with BWR resin) with decorative face veneers on one face, fixed with screws to timber frame work complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate) as in paving/plinth protection , laid in alternate bays, finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 40 mm thk PCC 1:2:4 type B-1 (using20mm graded aggregate) as in flooring finished even and smooth with using extra cement ,complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular), area of each tiles exc 0.06 Sqm but not exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and piinted in white/coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular), area of each tiles exc 0.11 Sqm but not exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and piinted in white/coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed

All as per item No 71.00 here-in-before but as in skirting/ dado for vertival surfaces ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular), area of each tiles exc 0.18 Sqm but not exc 0.38 Sqm in floors etc set and jointed in neat cement slurry and piinted in white/coloured cement to match ,including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

All as per item No 71.00 here-in-before but as in skirting/ dado for vertival surfaces ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300mm x 200mm x 7mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match with the existing, ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match with the existing ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on walls built in cement mortar etc including racking out joints, hacking for key, scrubbing down with water etc ,complete all as directed.

M&L for 15mm thick cement plastering in cement mortar 1:4 brick or concrete surfaces of wall finished fair and even,complete all as specified and directed.

Demolition of reed lathing single or double including battens and plaster or chicken wire lathing complete all as directed.

S & F for 0.71 mm dia wire netting of galvanised steel wire of size 12 mm mesh fixed with tinned tack of wire staple complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 on one side of lathing finished even and smooth without using extra cement,complete all as specified and directed.

M&L for rendering 12 mm thick in CM 1:6 on other side of lathing finished even and smooth without using extra cement ,complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of white wash , complete all as specified and as directed.

All as per item No 84.00 here-in-before but two coat of white wash.

All as per item No 84.00 here-in-before but on ceiling.

M&L for preparation of newly plastered surface of wall and applying two coats of distemper oil emulsion over priming with chalk whiting , complete all as specified and as directed.

M&L for preparation of old decorated surface of wall and applying one coat of distemper oil emulsion , complete all as specified and as directed.

All as per item No 88.00 here-in-before but two coat of distemper .

M&L for complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over a coat of 3mm thick wall care putty filling complete all as specified and directed.

M&L preparation of newly plastered surface of any description and applying two coat of plastic emulsion paint complete all as specified and as directed.

Preparation of old decorated plastered surface of any description and applying one coat of plastic emulsion paint complete all as specified and as directed.

Hacking out old broken glass of any thicknesssize or description from wooden frames or metal frames fixed with wooden beads/ putty , complete all as directed.

S&F Sheet glass 4.8mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane , complete all as specified and as directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane, , complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over priming coat of pink primer complete all as specified and as directed.

M&L for preparation of old decorated wooden surfaces of any description, over 10cm in width or girth, not otherwise described,, and applying two coats of synthetic enamel paint (1st quality) complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over priming coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of old decorated steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described,, and applying one coat of synthetic enamel paint (1st quality) complete all as specified and as directed.

Complete removal of existing treatment of walls and preparation of old surfaces of wall including scrapping down, smoke soot, efflorescent salts trading oil and greasy spots etcapplying two coats of cement base paint over a coat of over priming coat of alkali resistant priming paint ,complete all as specified and as directed.

M&L for preparing old painted surfaces of wall by washing, rubbing down and stopping of painted surfaces and applying a coat of cement base paint ,complete all as specified and as directed .

M&L for preparation old decorated surfaces on wall and applying one coat of weather exterior acrylic emulson wall paint ,complete all as specified and as directed.

M&L for complete removal of existing treatment of wall and applying two coats of exterior emulsion paint (weather coat) over a coat of approved primer complete all as specified and directed.

M&L forFrench polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and as directed.

S&F Vitreous China wash down water closet pan (pedestal pattern) white with P or S Trap, Joints between Flush Pipe and Socket of WC Pan (excluding Flushing Cistern and Flush Pipe), fixing with fixing bolts , fixed in repair ,complete all as specified and as directed..

S&F vitreous china wash hand basin, white, flat back, size 550x 400 mm including a pair of MS brackets and cutting for pinning in ends of brackets but including chain and plug and porcelain stopper, MS chromium plated grating, PVC waste pipe fixed in repair,complete all as specified and as directed.

S&F for Vitreous china urinal, flate type, size 465 x355x265 mm, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back with grating and union for discharge pipe (excluding flushing cistern flush pipe and waste pipe) complete all as specified and as directed.

S&F PVC connections pipe ,15mm dia size with PTMT nuts of length 450mm ,fixed in repair, complete all as specified and as directed.

S&F PVC flushing cistern 10 litre capacity, low level valve less, symphonic action type, white, with inlet, ball valve, float and handle including 32mm dia PVC flush pipe, a pair of cast iron brackets duly painted/ recting stand including cutting and pinning in ends, making good disturbed surfaces in cement mortar 1:3,, fixed in repair,complete all as specified and directed.

S&F brass chromium plated tubular towel Rail, 20mm dia, D type, 60cm long between flanges , fixed in repair, complete all as specified and as directed.

S&F PVC waste pipe, 32mm bore, 750mm long for basin, fixed in repair, complete all as specified and directed.

S&F 32mm dia waste coupling of PTMT (half or full threaded) (minimum weight 45 gms) fixed in repair ,complete all as specified and directed.

S&F (Health Faucet) with 8mm dia, 1 m long flexible tube & wall hook fixed in repairs,complete as specified and as directed. . Make : ESSCO/ HINDWARE/ PRAYAG or equivalent

S&F PVC waste pipe, 32mm bore, 750mm long for basin, fixed in repair, complete all as specified and directed.

Supply and fix plastic water closet seat cover, white closed pattern with flat bottom and cover and MS chromium plated or aluminium hanging device ,fixed in repair, complete all as specified and directed.

S&F Wall mixer 3-in-1 System with Provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting Legs and wall flange (without hand & overhead shower) Make : ESSCO/ HINDWARE/ PRAYAG or equivalent

S&F 15mm bore, CP single lever Basin Mixer without popup waste system with 450mm long copper pipes and brass nuts , fixed in repairs, complete as specified and directed. Make : ESSCO/ HINDWARE/ PRAYAG or equivalent

S&F Bib tap, 15 mm bore , screwed for iron pipe for brass ferrule ,fixed in repair complete all as specified and directed. Make : ESSCO/ HINDWARE/ PRAYAG or equivalent

S&F pillar tap 15 mm bore,chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' long screwed shanks and fly-nuts screwed for iron pipe, fixed in repair , complete all as specified and directed. Make : ESSCO/ HINDWARE/ PRAYAG or equivalent

S&F angle Stop valves, 15mm bore, ,chromium plated, serewed down high pressure, with crutch or butter fly handle, for iron pipe or for union a , complete all as specified and directed. (MAKE:- Prayag or equivalent of make Cera/Hindware/ Century)

Demolition/breaking up drain pipes (salt glazed ware/ PVC ) 110/75 mm bore (dia), jointed in cement mortar of any description including PCC of packing and haunching to sides of the pipes (except Bed), complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipe single socketed in any length with rubber ring joints ,fixed on wall , complete all as specified and as directed.

S&F 75 mm PVC (SWR) pipe single socketed in any length with rubber ring joints ,fixed on wall , complete all as specified and as directed.

S&F 110 mm PVC (SWR) bends any radius provided with acess door complete all as specified and as directed

S&F 75 mm PVC (SWR) bends any radius provided with acess door complete all as specified and as directed

S & F 110 mm dia PVC (SWR) vent cowl complete all specified and as directed.

S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement, fixed in repair complete all as specified and as directed.

Taking up or down galvanised steel water tubing 15/20 mm bore from wall/ceiling/floor including all fittings, complete all as directed

Refixing old serviceable galvanised steel water tubing 15mm bore, (serviceable pipe obtained from item No 129.00 here-in-before) in new or old situation/alignment of wall, ceiling or floor including provision of all new fittings including discaling/cleaning of pipe (internally and externally) cutting and threading of tubing ends complete all as specified and as directed.

All as per item No 130.00 here-in-before but 20mm dia GI pipe

S&F 15mm dia steel water tubing, galvanised, medium grade, with all fittings and fixed to wall and ceiling or laid in floor in old/new position ,including taking down the old unserviceable pipe,complete all as specified and as directed.

S&F 20 mm dia steel water tubing, galvanised, medium grade, with all fittings and fixed to wall and ceiling or laid in floor in old/new position ,including taking down the old unserviceable pipe,complete all as specified and as directed.

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1;3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for conceald water tubing and making good, cutting not exc 20 cm girth , complete all as specified and directed.

PERFECT BUILDERS AND SUPPLIERS

sanjay kumar

M/S Lucky Builders