Construction of community hall with public toilet blocks for male and female at Khoirom Village, Thoubal Dist, Manipur

Amount

Schedule 'A'

M/L earth work in excavation in trenches n exc 1.5 mtr in width getting out in soil.

M/L for PCC 1:4:8 type D2 40 mm graded for idn.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering finishing and reinforcement - All work above plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering finishing and reinforcement - All work above plinth level : 1:2:4 (1 cement : 2 coarse sand (Zone -III): 4 graded stone aggregate 20 mm nominal size)

M/L of form work to slides of fdn column Columns, piers abutments, pillars, posts and base slab.

Steel reinforcement for RCC work including straightening, cutting, bending all complete upto plinth level. Thermo-Mechanically Treated bars.

Brick work with common burnt clay modular bricks of class designation. 7.5 in foundation and plinth in : cement Mortar 1:6 (1 cement : 6 corase sand )

Brick work with common burnt clay modular bricks of class designation. 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand ) cum

Half Brick masonry with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level 6.13.2 Cement mortor 1:4

Providing and laying in position cement concrete of spcified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 including finishing flooring.

12 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 ( 1 Cement : 6 fine sand) (Half brick wall upto roof, gabble wall, deduction door, window,steps

steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structral steet etc. as required. In stair cases. Including use of chequered plate wherever required, all complete Kg. Plate MS 8mm thick, 6mm thick cleat, Plate MS 6mm thick

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, special shaped washers etc. complete. Hot finished welded MS tube 88.90 mm OD, MS tube 48.30mm OD (purlin), Main turss/rafter 33.70mm OD, Tie beam 42.4mm OD and MS Tube 26.90 mm OD (main truss strut), Main truss/rafter 33.70 mm OD

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. Bolts 65 mm long 12 mm dia

Providing corrugated GS sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G. I limpet washers or with G. I limpet washer filled with white lead, including a coat of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/m roof.

Providijng wood work in frames of false ceiling, partitions etc. sawn and fixed in position : 2nd class H/wood Ceiling

Providing ridges or hips of width 60 cm overall width plain G S sheet fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G. I limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/Sqm

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separetely. 2nd class H/wood

Providing and fixing glass panes with putty and glazing clips in steel doors windows, clerestory windows, all complete with : 4.0 mm thick glass panes

Providing and fixing ISI marked oxidised M.S handles conforming to IS : 4992 with necessary screws etc. completed : 125mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150 x10mm

Providing and fixing ISI marked oxidised M.S sliding door bolts with nuts and screws etc. complete : 300x16mm

Making plinth proction 50mm thick of cement concrete 1:3:6 (1 cement: 3 Coarse sand :6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Painting with synthetic enamel paint of approved brand and manifacture to give an even shade : two or more coats on door

M/S G.S. SHEKHAWAT (BID ID -3088231)

M/s Mahesh Kumar Gupta (BID ID -3089591)